石墨烯掺杂Cs2CO3作为高效电子注入层的OLEDs性能研究

研制了石墨烯掺杂Cs₂CO₃(Cs₂CO₃:Graphe ne )作为高效电子注入层、结构为ITO/N,N′-bis-(1-naphthyl) -N,N′-diphenyl-1,1′-biphenyl-4,4′-diamine (NPB)(50 nm)/tris-(8-hydroxy quinoline)-aluminum Alq₃(80 nm)/Cs₂CO₃:Gra phene (mss 20% 1nm)/Al(120 nm)的OLEDs。将其与标准器件ITO/NPB(50 nm)/Alq₃(80 n m)/LiF(0.5 nm)/Al(120 nm)作性能比较,研究石墨烯掺杂在Cs₂CO₃中作为电子注入层 对 OLEDs性能的影响。结果表明,基于Cs₂CO₃:Graphene结构作为电子注入层的器 件效率要高于LiF作为电子注入层的器件,其最大电流效率达到2.02 cd/A, 是标准器件的2.59倍;亮度也高于LiF作为电子注入层的器件,在10 V时达 到最大值7690cd/m²,是标准器件最大亮度 的2.07倍。性能得到提高的主要机理是由于Cs₂CO₃:Graphene的引入提高了电子注入效率。     

可调谐氮化硅波导微环谐振腔滤波器研究

设计并制备了一种基于热光效应的集成可调谐氮化 硅(Si₃N₄)波导微环谐振腔滤波器,通过采用马赫-曾德干涉仪(MZI)构成的可调谐 耦合器控制耦合区耦合比,以实现滤波器消光比的调谐。设计并优化了微环谐振 腔的波导截面尺寸、弯曲半径和耦合区波导间隔等参数,并通过光刻、反应离子刻蚀(RIE )等工艺制备 了两种不同弯曲半径的Si₃N₄波导微环谐振腔。实验结果表明,本文器件在波长1550nm附近处的自由光谱 范围(FSR)为68pm,3dB带宽约为16pm,品质因子Q达到了9.68×10 4,消光比可调范围约为17dB。     

VOLTE容灾机制研究及优化方案

_{本文首先对VOLTE现网网络结构及容灾机制进行研究分析,发现现存容灾机制中存在的缺点和不确定性,针对其中的问题,针对性地进行了深入研究和分析,创新的提出了1种快速容灾抢通方案,以达到提升VOLTE业务运维能力和用户业务感知的目的。}     

WO3对Rubrene/C70有机太阳能电池性能的改善

研究了WO₃对Rubrene/C₇₀有机太阳能电池 (OSCs)性能的 改善,制备了结构为ITO/WO₃/Rubrene/C₇₀/BCP/Al的OSCs,其中WO₃插入在I TO和Rubrene中间作为阳极修饰层。通过优化WO₃的厚度,研究了WO₃对OSCs性能的改善及其作用机理。实验发现,器件的短路电流Jsc、开路电压V_oc、 填充因子(FF)、光电转换效率(PCE)和串联电阻Rs等性能参数随WO₃厚度的变化呈规律性变化;当 WO₃厚度小于80 nm时,器件PCE随着厚度的增加不断增大;当W O ₃厚大于80 nm时,器件PCE随着厚度的 增加不断减小;当WO₃厚度为80 nm 时,器件PCE达到最高为1.03%, 相应的J sc、V_oc、FF分别为2.81mA·cm－2、 0.83V、43.85%,Rs为45.3Ω·cm²,对比没有WO₃修饰层, 器件的J_sc、V_oc、FF和PCE分别提高了31%、137%、17%,Rs降低了33%。     

基于Bphen:BCP:Cs2CO3作为电子传输层的OLED性能研究

为了进一步平衡OLED器件内部空穴和电子载流子 的注入,制备了结构为ITO/NPB(40nm)/Alq₃(45nm)/Bphen:(X%)BCP:(5%)Cs₂CO₃(15nm)/Cs₂CO₃(1.5 nm)/Al(100nm)的OLED器件,通过改变BCP 的掺杂浓度,研究了以Bphen:BCP:Cs₂CO₃作为电子传输层对OLED器件发光亮度、电流 密度和效率等性能 的影响。结果表明,采用Bphen:BCP:Cs₂CO₃作为电子传输层能提高器件的电子注入能力 ,改善器件的性能, 相比于未引入BCP的器件,采用BCP掺杂浓度为10%的Bphen:BCP:Cs₂CO₃作为电子传输层 ,可以使器件 的最大电流效率提高46%,达到3.89cd/A,且 在电压从为5V上升至10V的过程中,器件的色坐标一直为 (0.35,0.55),具有很高的稳定性。原因是由于BCP的高LUMO能级和高 HOMO能级,能够有 效阻挡空穴到达阴极,减小空穴漏电流,同时使电子的注入更容易,电子和空穴的注入更加 平衡,发光也更加稳定。     

用溶胶-凝胶法制备的Cu2Bi2Cr2O8薄膜 及其光学和铁磁性能研究

以硝酸铜Cu(NO₃)₂·3H₂O、硝酸铬Cr(NO₃)₃·9H₂O、硝酸铋Bi(NO₃)₃·3H₂O和乙二醇为原料,利用溶胶-凝胶工艺在石英衬底上制备了纳米Cu₂Bi₂Cr₂O₈薄膜。通过X射线衍射(X-Ray Diffraction, XRD)和拉曼测试对样品进行了表征。结果表明,Cu₂Bi₂Cr₂O₈薄膜具有良好的光学特性,其禁带宽度为1.49 eV;在磁性测试方面,Cu₂Bi₂Cr₂O₈薄膜呈现出了良好的铁磁性。     

MgF2/Se薄膜封装层对OLED性能及寿命的影响

有机电致发光器件(OLEDs)在使用过程中,易受到 空气中水汽、氧气及其它污染物的影响从而导致其工作寿命降低。本文将具有良好光透过率 和热稳定性的MgF₂薄膜与在水汽和氧气中具有良好稳定性的Se薄膜通过真空蒸镀制成复 合薄膜作为OLEDs的封装层,以达到提高器件使用寿命的目的。器件各功能层蒸镀完成后, 保持真空度(3×10－4 Pa)不变,在阴极表面蒸镀MgF₂/Se薄 膜封装层。比较 了绿光OLED器件(器件结构为ITO/CuPc/NPB/Alq₃:C-545T/Alq ₃/LiF/Al)封装前后的亮度-电压-电流密度特性、电致发光光谱及寿命。研究 发现,经过MgF₂/Se封装后,器件的电流密度-电压特性、亮度和发光光谱几乎没 有受到影响,二者的光谱峰都在528 nm处,色坐标(CIE)分别为(0.3555,0.6131)和(0.3560,0.6104),只是起亮电压由3V变为4V;器件的寿命由原来的175h变为300h,提高了1.7倍 。因此,MgF₂/Se薄膜是一种有效的OLEDs无机薄膜封装层。     

Co3O4/Fe2O3异质结复合材料的制备及其紫外光光电探测性能

分别采用旋涂法和水热法在FTO衬底上制备Co₃O₄种子层和Co₃O₄薄膜,再在Co₃O₄薄膜上水热生长Fe₂O₃纳米棒,获得了高质量的Co₃O₄/Fe₂O₃异质结复合材料。通过改变Fe₂O₃前驱体溶液浓度来改变异质结复合材料中Fe₂O₃组分的含量。结果表明,Fe₂O₃纳米棒覆盖在呈网状结构的Co₃O₄薄膜上,随着Fe₂O₃前驱体溶液浓度即Fe₂O₃组分含量的增加,Co₃O₄/Fe₂O₃异质结复合材料对紫外光的响应逐渐增强,当Fe₂O₃前驱体溶液浓度为0.015mol/L时,异质结复合材料有着很好的光电稳定性,并表现出较高的响应率(12.5mA/W)和探测率(4.4×10¹⁰Jones)。     

InyAl1-yAs线性渐变缓冲层对InP基HEMT材料性能的影响

采用气体源分子束外延（GSMBE）技术,研究了InP衬底上In_yAl_1-yAs线性渐变缓冲层对In_0.66Ga_0.34As/In_yAl_1-yAs高迁移率晶体管（HEMT）材料特性影响。研究了不同厚度和不同铟含量的In_yAl_1-yAs线性渐变缓冲层对材料的表面质量、电子迁移率和二维电子气浓度的影响。结果表明,在300 K（77 K）时,电子迁移率和电子浓度分别为8 570 cm²/（Vs）^-1（23 200 cm²/（Vs）-1）3.255E12 cm^-2（2.732E12 cm^-2）。当In_yAl_1-yAs线性渐变缓冲层厚度为50 nm时,材料的表面形貌得到了很好的改善,均方根粗糙度（RMS）为0.154 nm。本研究可以为HEMT器件性能的提高提供强有力的支持。     

Ca3Y2(Si3O9)2:Tb3+绿色荧光粉的光谱特性

采用高温固相法制备了Ca₃Y₂(Si₃O₉)₂: Tb³⁺绿色荧光粉,研究了材料的光学性能。X 射线衍射(XRD)结果显示,掺杂少量的Tb³⁺,并未影响Ca₃Y₂(Si₃O₉)₂材料 的晶相结构。Ca₃Y₂(Si₃O₉)₂:Tb³⁺ 荧光粉的激发光谱由较强的4f^75d1宽带吸收(200～300 nm )和较弱的4f-4f电子跃迁吸收 (300～500 nm)构成,主激发峰位于236nm。取波长分别为236、376和482nm的光 作为激发源时,发现样品的主发射峰均位于544 nm,对应Tb³⁺的⁵D 4→⁷F₅跃迁发射。以236nm 紫外光作为激发源,监测544nm主发射峰,随Tb³⁺浓度 的增大,Ca₃Y₂(Si ₃O₉)₂:Tb³⁺的荧光寿命逐渐减小,但在实验范围内并未出现浓度猝灭现象。     

Iron nitride mask and reactive ion etching of GaN films

One of the major GaN processing challenges is useful pattern transfer. Serious photoresist mask erosion and hardening are often observed in reactive ion etching of GaN. Fine pattern transfer to GaN films using photoresist masks and complete removal of remaining photoresist after etching are very difficult. By replacing the etch mask from conventional photoresist to a sputtered iron nitride (Fe-8% N) film, which is easily patterned by wet chemical etching and is very resistive to Cl based plasmas, GaN films can be finely patterned with vertical etched sidewalls. Successful pattern transfer is realized by reactive ion etching using Cl (H) containing plasmas. CHF₃/Ar, C₂ClF₅/Ar, C₂ClF₅/Ar/O₂, SiCl₄, and CHCl₃ plasmas were used to etch GaN. The GaN etch rate is dependent on the crystalline quality of GaN. Higher crystalline quality GaN films exhibit slower etch rates than GaN films with higher dislocation and stacking fault density.     

硅各向同性深刻蚀中的多层掩模工艺

掩模制备是硅各向同性刻蚀中的一项重要工艺.要实现深刻蚀,掩模必须满足结构致密、强度大及抗腐蚀性好的要求.一般光刻胶掩模无法在刻蚀液中较长时间地保持其掩蔽性能,很难实现深刻蚀;而金属掩模也容易出现针孔及裂纹等缺陷.因此提出使用Su-8负性光刻胶结合铬金属制备多层掩模.这种掩模结构制备工艺简单,经济实用;提高了掩模在高速刻蚀时的掩蔽性能,实现了深刻蚀.实验表明,其能满足300μm以上深刻蚀的要求,可用于硅及玻璃等材料的微加工.     

以非晶硅为硬掩膜的TaN金属栅的选择性湿法腐蚀

提出了一种在HfSiON介质上,采用非晶硅为硬掩膜的选择性去除TaN的湿法腐蚀工艺。由于SC1(NH4OH:H2O2:H2O)对金属栅具有合适的腐蚀速率且对硬掩膜和高K材料的选择比很高,所以选择它作为TaN的腐蚀溶液。与光刻胶掩膜和TEOS硬掩膜相比,因非晶硅硬掩膜不受SC1溶液的影响且很容易用NH4OH溶液去除（NH4OH溶液对TaN和HfSiON薄膜无损伤）,所以对于在HfSiON介质上实现TaN的选择性去除来说非晶硅硬掩膜是更好的选择。另外,在TaN金属栅湿法腐蚀和硬掩膜去除后, 高K介质的表面是光滑的,这可防止器件性能退化。因此,采用非晶硅为硬掩膜的TaN湿法腐蚀工艺可以应用于双金属栅集成,实现先淀积的TaN金属栅的选择性去除。     

Patterning and etching of amorphous teflon films

Amorphous Teflon®, deposited by spin-coating and thermal evaporation, has been studied as a low dielectric constant insulator for high performance interconnects. Since it is difficult to deposit a film on amorphous Teflon because of its inert chemical bonds, plasma etching and Zonyl FSN® fluorosurfactant are used to improve the adhesion of photoresist to amorphous Teflon. Plasma etching is shown to increase surface roughness and change chemical bonds of the amorphous Teflon, resulting in improved adhesion of metals and SiO₂ to amorphous Teflon. While amorphous Teflon cannot be etched by wet chemicals, etching the films in Ar, O₂, or CF₄/O₂ plasma is very effective.     

Removal of post-etch photoresist and sidewall residues using organic solvent and additive combined with physical forces

The effect of tetramethyl ammonium hydroxide (TMAH) used as additive in organic solvent (N-methyl pyrrolidone, NMP) on removal efficiency of post-etch photoresist was investigated on both blanket substrate and single damascene structures. In contrast to plasma ashing, photoresist removal using NMP/TMAH combined with megasonics showed no carbon depletion and no significant change in k-value. Mixing TMAH with NMP enhanced photoresist removal efficiency with respect to pure NMP. Photoresist removal using NMP/TMAH resulted in lower low-k capacitance (lower k-value) compared with that of plasma ashing process, due to the removal of the damaged layer generated during plasma etching. As a consequence of the removal of the damaged layer, a CD change was observed. The CD loss was estimated to be about 7 nm for 1% TMAH, and became negligible for 0.1% TMAH. Analysis of low-k sidewall using angle-resolved X-ray photoelectron spectroscopy showed that solvent mixture containing TMAH also removed sidewall residues generated by the etch plasma.     

Aspect-ratio-independent anisotropic silicon etching in a plasma chemical cyclic process

The conditions of implementation of aspect-ratio-independent etching (ARIE) are given for a two-stage etching/passivation process in an SF₆/C₄F₈ plasma. It is shown experimentally that the ARIE etching is achieved by extension of the stage of passivation and/or reduction of the energy of ions at the stage of etching. These phenomena lead to prolonged removal of the fluorocarbon film, which affects the dependence of the etching rate on the aspect ratio of the groove. A model of cyclic etching is presented that takes into account the aspect dependences of the processes on the groove bottom, namely, Si etching and deposition and removal of the fluorocarbon film. The simulation results correlate satisfactorily with the experimental data. Limitations of implementation of ARIE etching are discussed.     

Transferring of GaAs microtips using selective wet etching Al0.7Ga0.3As sacrificial layer

GaAs pyramidal microtips were successfully transferred from GaAs substrate to target wafer by a simple technique, i.e., selective wet etching off AlGaAs sacrificial layer. A GaAs/Al_0.7Ga_0.3As/GaAs sandwich structure is firstly formed on GaAs (0 0 1) substrate by metalorganic chemical vapor deposition, and then GaAs pyramidal microtips are grown on the sandwich structure using selective liquid-phase epitaxy. The GaAs microtips are removed from the sandwich structure by selective wet etching Al_0.7Ga_0.3As layer using concentrated HCl solution. Finally, the tips are glued onto the target wafer by a negative photoresist. During this transfer process the tips are completely encapsulated in a positive photoresist to protect against attack. Scanning electron microscopy images show that GaAs tips can be successfully transferred without any damage by this technique. The achievement reported here represents a significant step towards the application of scanning near-field optical microscopy.     

Investigations on a Multiple Mask Technique to Depress Processing-Induced Damage of ICP-Etched HgCdTe Trenches

A multiple mask technique, integrating patterned silicon dioxide (SiO₂) film over patterned thick photoresist (PR) film, has been investigated as a method to perform mesa etching for device delineation and electrical isolation of mercury cadmium telluride (HgCdTe) third-generation infrared focal-plane arrays. The multiple mask technique was achieved by standard thick PR photolithography, SiO₂ film deposition to cover the thick PR patterned film, and etching the SiO₂ film at the bottom region after another photolithography process. The dynamic resistance in the zero-bias and low-reverse-bias regions of HgCdTe photodiode arrays isolated by inductively coupled plasma (ICP) etching with the multiple mask of patterned SiO₂ and patterned thick PR film underneath was improved one- to twofold compared with a simple mask of patterned SiO₂. It is suggested that the multiple mask technique is capable of maintaining high etching selectivity while reducing the side-wall processing-induced damage of ICP-etched HgCdTe trenches. The results show that the multiple mask technique is readily available and shows great promise for etching HgCdTe mesa arrays.     

Calcination‐ and Etching‐Free Photolithography of Inorganic Phosphor Films Consisting of Rare Earth Ion Doped Nanoparticles on Plastic Sheets

It is demonstrated that patterned inorganic phosphor films consisting of rare earth ion doped nanoparticles (RE‐NPs) can be fabricated on plastic sheets using calcination‐ and etching‐free photolithography. Green up‐conversion luminescence and near‐infrared (NIR) fluorescence appears from the RE‐NPs that are prepared from Y₂O₃ doped with 1 mol% Er³⁺ and 0.85 mol% Yb³⁺. The diameter of the RE‐NPs is estimated to be about 300 nm using dynamic light scattering. Visible transmittance of the RE‐NP film fabricated by dip‐coating is more than 90%. Patterned RE‐NP films are obtained by dip‐coating the RE‐NPs on patterned photoresist films fabricated by UV exposure through a photomask, followed by selective removal of the photoresist. Optical, fluorescence, scanning electron, atomic force, and Kelvin probe force microscopies are used for the characterization of the patterned RE‐NP films. The present methodology enables fabrication of patterned RE‐NP films, not only on inorganic substrates but also on plastic sheets, with low cost and material consumption.     

Wet Etching Study of La0.67(Sr0.5Ca0.5)0.33MnO3 Films on Silicon Substrates

Wet etching of colossal magnetoresistive (CMR) perovskite La_0.67(Sr_0.5 Ca_0.5)_0.33MnO₃ (LSCMO) films on Bi₄Ti₃O₁₂/CeO₂/yttrium-stabilized zirconia (YSZ)-buffered Si substrates was investigated using potassium hydroxide (KOH) and buffered hydrofluoric acid (BHF) solutions. X-ray diffraction (XRD) and scanning spreading resistance microscopy (SSRM) measurements revealed that the morphological roughness of the LSCMO films increases, while the electrical resistance roughness decreases, with increasing KOH etching time. The LSCMO films are highly chemically resistant to KOH solution; however, in the case of BHF etching, an etch rate of 22 nm/min was obtained with high selectivity over a photoresist mask.