Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Fe_2O_3/Al_2O_3催化剂制备及催化降解酸性染料废水

以γ-Al2O3>为载体,采用浸渍-焙烧法制备了Fe2O3/Al2O3催化剂.并将其用于催化降解模拟酸性大红-3R染料废水.对于质量浓度为1 000 mg/L的高浓度酸性大红-3R染料废水,最佳的处理工艺条件为:温度60℃、pH=3.0、H2O2投加质量浓度9.4g/L、催化剂投加质量浓度1.5 g/L.在此工艺条件下酸性大红染料废水的降解率为99%,CODCr的去除率>83%.而对于质量浓度≤100 mg/L的酸性大红-3R染料废水在此条件下的降解速率接近100%.且催化剂连续使用6次后仍有较高的催化活性.     

CuO-ZnO/Al_2O_3催化剂对醋酸甲酯催化加氢制乙醇的研究

采用并流共沉淀法制备了醋酸甲酯催化加氢合成乙醇的CuO-ZnO/Al_2O_3催化剂,并通过N_2物理吸附、X射线衍射(XRD)、程序升温还原(H_2-TPR)、扫描电子显微镜(SEM)等表征手段分析了催化剂的物理化学特性,探究加料方式、铜锌铝的配比对催化剂结构的影响与催化剂活性之间的关系。结果表明,加料方式为并流、铜锌铝的配比为5∶2∶1时,催化剂前驱体的架构最为规整,焙烧后得到的CuO颗粒较小,且分散最为均匀,具有较多且分散的活性组分,表现出了最优的加氢性能。在反应温度220℃,反应压力3.0MPa,质量液时空速0.5h-1和氢酯物质的量比9的条件下,醋酸甲酯的转化率达到97.6%,乙醇的选择性高达97.5%。     

CuO-ZnO/Al_2O_3催化剂对醋酸甲酯催化加氢制乙醇的研究

采用并流共沉淀法制备了醋酸甲酯催化加氢合成乙醇的CuO-ZnO/Al_2O_3催化剂,并通过N_2物理吸附、X射线衍射(XRD)、程序升温还原(H_2-TPR)、扫描电子显微镜(SEM)等表征手段分析了催化剂的物理化学特性,探究加料方式、铜锌铝的配比对催化剂结构的影响与催化剂活性之间的关系。结果表明,加料方式为并流、铜锌铝的配比为5∶2∶1时,催化剂前驱体的架构最为规整,焙烧后得到的CuO颗粒较小,且分散最为均匀,具有较多且分散的活性组分,表现出了最优的加氢性能。在反应温度220℃,反应压力3.0MPa,质量液时空速0.5h-1和氢酯物质的量比9的条件下,醋酸甲酯的转化率达到97.6%,乙醇的选择性高达97.5%。     

搅拌速率对Pd/Al_2O_3催化剂CH_4催化燃烧性能的影响

为了考察搅拌速率在Pd/Al2O3催化剂制备过程中的作用,通过对不同搅拌速率制备的Pd/Al2O3催化剂进行XRD、H2-TPR和XPS表征及CH4催化燃烧活性测试,研究搅拌速率对Pd/Al2O3催化剂活性的影响。结果表明,低搅拌速率[(200~300)r·min-1]条件制备的催化剂,Pd O粒径较大,Pd分散度高,表面Pd与Pd O物质的量比=0.55~0.56,催化剂的CH4催化反应活化能与无搅拌时相比降低,在200 r·min-1达到最低;随着搅拌速率增加,高搅拌速率[(400~600)r·min-1]抑制了Pd O晶粒的生长,导致Pd O粒径变小,Pd分散度降低,并使表面Pd O含量增大,Pd与Pd O物质的量比=0.41~0.52,提高了CH4催化燃烧反应的活化能。     

Nd-Cr/Al_2O_3催化剂上苯直接氧化制苯酚的动力学研究

研究了苯直接氧化制苯酚反应的动力学行为。推测了Nd-Cr/Al2O3催化剂上过氧化氢氧化苯为苯酚的反应过程,建立了该反应动力学数学模型,模型很好的解释了实验结果。结果表明,在实验条件下,该羟基化反应对反应物苯、氧化剂过氧化氢和催化剂用量都是一级反应,反应的活化能为24.41 kJ/mol。     

Pd/Al_2O_3催化剂催化加氢处理六氯苯的新工艺

利用自制的固定床反应器研究了六氯苯催化加氢反应。结果表明负载单一金属Pd催化效果明显,但催化剂不够稳定,容易积碳失活,加入第二种金属有效增长了催化剂的寿命。并最终优化了工艺条件。     

Fe/Al_2O_3催化剂催化氧化兰炭废水

采用浸渍法制备Fe/Al_2O_3催化剂,采用BET、XRD和穆斯堡尔谱等进行结构和性能表征。以自制Fe/Al_2O_3为催化剂,应用催化湿式过氧化氢氧化技术处理COD为6 742 mg·L-1的兰炭废水,通过建立正交实验确定最佳实验条件,结果表明,在p H=4、过氧化氢添加量9.6 m L、反应时间150 min和反应温度80℃条件下,兰炭废水COD去除率达66.30%。对催化氧化后的废水进行GC-MS分析,确定最终氧化产物主要为乙酸。表明自制Fe/Al_2O_3催化剂具有优良的催化效果,并使大分子难降解有机污染物分解为易生化的小分子污染物,甚至被完全分解矿化。     

Pt/Al_2O_3与Pt/MgO-Al_2O_3催化剂制备及其催化氢能载体甲基环己烷脱氢反应性能

以碱共沉淀法制备Mg-Al水滑石,然后采用浸渍法负载活性组分Pt,经焙烧、氢气还原得到Pt/Al_2O_3与Pt/Mg O-Al_2O_3催化剂,采用XRD、N2吸附-脱附、FT-IR、H2-TPR和Py-IR等分析Mg O的加入对Pt/Al_2O_3催化剂结构性能的影响,并在甲基环己烷连续脱氢反应中对比两种催化剂活性。结果表明,Pt/Mg O-Al_2O_3催化剂比表面积小于Pt/Al_2O_3催化剂,且表面基本无酸性活性中心,但表现出与Pt/Al_2O_3催化剂相同的脱氢活性。在Pt负载质量分数2%、催化剂用量0.5 g、甲基环己烷0.1 m L·min-1纯样进料和325℃反应10 h后,原料平均转化率79.9%,脱氢产物只有甲苯,对应的产氢速率192.8 mmol·(g-metal·min)-1,表现出优良的脱氢活性。     

TiO_2/Al_2O_3复合载体用于有机硫加氢转化催化剂的研究

研究了不同TiO2 含量对有机硫加氢转化催化剂活性的影响 ,并与单一Al2 O3 作载体的催化剂进行了性能对比。结果表明 ,用TiO2 /Al2 O3 复合载体制得的有机硫加氢转化催化剂 ,性能明显改善 ,对噻吩的平均转化率由原 34 .73%提高到 6 7.5 2 % ;催化剂预硫化所需硫化剂量可减少 5 0 %以上。     

Selective reduction of NO on Ag/Al2O3 catalysts prepared from boehmite needles

Ag/Al₂O₃ catalysts prepared from boehmite needles (ca. 10 nm×100 nm), which were formed by a hydrolysis of aluminium tri-isopropoxide (AIP), showed good performances for selective catalytic reduction of NO_x compared with the previously reported catalysts [N. Aoyama, K. Yoshida, A. Abe, T. Miyadera, Catal. Lett. 43 (1997) 249], especially when ethanol is employed as a reducing agent in the presence of water. Temperature programmed reduction (TPR) study revealed that the Ag species are attractively interacted with the alumina surface and the oxidized Ag species contribute positively for the improvement of the catalytic activity at the temperatures above 750 K. It is concluded that the boehmite needles as a precursor of alumina support are useful to create the catalytically active sites for NO_x reduction.     

The mechanism of SO2 effect on NO reduction with propene over In2O3/Al2O3 catalyst

An In₂O₃/Al₂O₃ catalyst shows high activity for the selective catalytic reduction of NO with propene in the presence of oxygen. The presence of SO₂ in feed gas suppressed the catalytic activity dramatically at high temperatures; however it was enhanced in the low temperature range of 473–573 K. In TPD and FT-IR studies, the formation of sulfate species on the surface of the catalyst caused an inhibition of NO_X adsorption sites, and the absorbance ability of NO was suppressed by the presence of SO₂, and the amount of ad-NO₃⁻ species decreased obviously. This leads to a decrease of catalytic activity at higher temperatures. However, addition of SO₂ enhanced the formation of carboxylate and formate species, which can explain the promotional effect of SO₂ at low temperature, because active C₃H₆ (partially oxidized C₃H₆) is crucial at low temperature.     

Ru-Fe/Al_2O_3氧化-还原性能探究

以Al_2O_3为载体,RuCl_3·xH_2O和FeCl_3·6H_2O为活性组分前驱体,采用吸附-沉淀法制备了Ru-Fe/Al_2O_3和Ru/Al_2O_3催化剂,以马来酸二甲酯加氢合成丁二酸二甲酯为探针反应,结合H_2-TPR和XRD表征技术,考察Fe改性Ru基催化剂的氧化-还原性能及催化活性。经氧化-还原循环处理后,催化剂Ru-Fe/Al_2O_3上马来酸二甲酯加氢活性高于Ru/Al_2O_3。XRD结果显示,经处理的Ru-Fe/Al_2O_3上未见金属Ru的特征衍射峰,而Ru/Al_2O_3上出现了金属Ru的特征衍射峰。结合H_2-TPR结果推断,Ru与Fe之间发生了相互作用,这种协同作用可以改善Ru/Al_2O_3催化剂的热稳定性。     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

焙烧温度对NiMo/Al2O3催化剂加氢性能的影响

采用不同的焙烧温度制备系列NiMo/Al₂O₃催化剂,运用BET、XRD、SEM和HRTEM等分析手段对催化剂进行表征,并以催化裂化进料为原料,在固定床高压反应器上对催化剂的加氢性能进行评价,着重考察焙烧温度对催化剂活性组分结构及活性的影响。结果表明,焙烧温度的升高有利于活性组分在催化剂表面的分散,但同时会增强活性组分与载体之间的相互作用,使催化剂活性相中单片层MoS₂片晶的数量增加,导致催化剂活性下降。
     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Effects of alumina incorporation in coprecipitated NiO–Al2O3 catalysts

The effect of Al₂O₃ levels on the properties of NiO in coprecipitated NiO–Al₂O₃ samples were investigated, using samples with up to 60.7 wt.% Al₂O₃ that had been calcined in the range 300–700°C. Characterization techniques included BET surface area of fresh and reduced catalysts, X-ray diffraction analysis of structure and crystallite size, magnetic susceptibility measurements, oxidizing power, and reducibility in H₂. Only NiO was detected in samples with up to 4.1 wt.% Al₂O₃ for all sample calcination temperatures. Surface areas were similar for all fresh samples but decreased rapidly after calcination at high temperatures. The surface area loss was less for the higher Al₂O₃-containing samples. Nickel oxide crystallite sizes increased at higher calcination temperatures, but remained approximately the same for each Al₂O₃ level.

The NiO was nonstoichiometric (NiO_1+x), with x decreasing at higher calcination temperatures and increasing with small amounts of added Al₂O₃ through a maximum at about 3 wt.% Al₂O₃. However, this did not correlate well with microstrain in the NiO crystallites nor with reducibility, which decreased with Al₂O₃ addition. At higher levels of Al₂O₃ (13.6 wt.% and above), surface areas increased with higher Al₂O₃ loadings, but NiO crystallite sizes remained approximately the same, independent of both Al₂O₃ content and calcination temperature. X-ray diffraction patterns were very diffuse, and it was not possible to rule out the presence of pseudo-spinel combinations of NiO and Al₂O₃. Reducibility was more difficult than with low Al₂O₃ levels, and nonstoichiometry was low and independent of Al₂O₃ content.

Reducibilities of all samples calcined at 300°C correlated well with the final BET surface area of the reduced samples, indicating that more dispersed NiO crystallites are more difficult to reduce, a conclusion that supports a model for reduction proposed previously.