Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Effects of substrates on the capacitive performance of RuOx·nH2O and activated carbon-RuOx electrodes for supercapacitors

The electrochemical energy storage and delivery on the electrodes composed of hydrous ruthenium oxide (RuO_x·nH₂O) or activated carbon-hydrous ruthenium oxide (AC-RuO_x) composites are found to strongly depend on the substrate employed. The contact resistance at the active material-graphite interface is much lower than that at the active material-stainless steel (SS) mesh interface. Thin films of gold plus RuO_x·nH₂O deposited on SS meshes (RuO_x/Au/SS) are found to greatly improve the poor contact between SS meshes and electrode materials. The maximum specific capacitance (C_S,RuOx) of RuO_x·nH₂O, 1580 F g⁻¹ (measured at 1 mV s⁻¹), very close to the theoretic value, was obtained from an AC-RuO_x/RuO_x/Au/SS electrode with 10 wt.% sol-gel-derived RuO_x·nH₂O annealed in air at 200 °C for 2 h. The highly electrochemical reversibility, high-power characteristics, good stability, and improved frequency response of this AC-RuO_x/RuO_x/Au/SS electrode demonstrate its promising application potential in supercapacitors. The ultrahigh specific capacitance of RuO_x·nH₂O probably results from the uniform size distribution of RuO_x·nH₂O nanoparticles, ranged from 1.5 to 3 nm which is clearly observed from the high-resolution transmission electron microscopy (HRTEM).     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Transesterification of palm oil on KyMg1 − xZn1 + xO3 catalyst: Effect of Mg-Zn interaction

The Mg-Zn interaction effect of K_yMg_1 − xZn_1 + xO₃ heterogeneous type catalyst and its performance on transesterification of palm oil have been studied using the response surface methodology and the factorial design of experiments. The catalyst was synthesized using the co-precipitation method and the activity was assessed by transesterification of palm oil into fatty acid methyl esters. The ratio of the Mg/Zn metal interaction, temperature and time of calcination were found to have positive influence on the conversion of palm oil to fatty acid methyl ester (FAME) with the effect of metal to metal ratio and temperature of calcination being more significant. The catalytic activity was found to decrease at higher calcination temperature and the catalyst type K₂Mg_0.34Zn_1.66O₃ with Mg/Zn ratio of 4.81 gave FAME content of 73% at a catalyst loading of 1.404 wt.% of oil with molar ratio of methanol to oil being 6:1 at temperature of 150 °C in 6 h. A regression model was obtained to predict conversions to methyl esters as a function of metal interaction ratio, temperature of calcination and time. The observed activity of the synthesized catalyst was due to its synergetic structure and composition.     

Hydrothermal synthesis and electrochemical capacitance of RuO2·xH2O loaded on benzenesulfonic functionalized MWCNTs

Amorphous RuO₂·xH₂O was well coated on the benzenesulfonic functionalized multi-wall carbon nanotubes (f-MWCNTs) successfully via hydrothermal method. The decorated benzenesulfonic groups served as a bifunctional role both for solubilizing and dispersing MWCNTs into aqueous solution and for tethering Ru³⁺ precursor to facilitate the following uniform chemical deposition of RuO₂·xH₂O. The electrochemical performance of RuO₂/f-MWCNTs and utilization of RuO₂·xH₂O were evidenced by cyclic voltammetry and galvanostatic charge/discharge tests. The specific capacitance of 1143 Fg⁻¹ for RuO₂·xH₂O was obtained from RuO₂/f-MWCNTs with 32 wt.% RuO₂·xH₂O, which was much higher than that of just 798 Fg⁻¹ for the RuO₂/p-MWCNTs. Even though the RuO₂·xH₂O loading increases to 45 wt.%, the utilization of RuO₂·xH₂O still possesses as high as 844.4 Fg⁻¹, indicating a good energy capacity in the case of high loading.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Study on the rapid synthesis of LiNi1−xCoxO2 cathode material for lithium secondary battery

LiNi_1−xCo_xO₂ (x = 0, 0.1, 0.2) cathode materials were successfully synthesized by a rheological phase reaction method with calcination time of 0.5 h at 800 °C. All obtained powders are pure phase with α-NaFeO₂ structure (R-3m space group). The samples deliver an initial discharge capacity of 182, 199 and 189 mAh g⁻¹ (25 mA g⁻¹, 4.35-3.0 V), respectively. The reaction mechanism was also discussed, which consists of a series of defect reactions. As a result of these defect reactions, the reaction of forming LiNi_1−xCo_xO₂ takes place in high speed.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

New binary (1 − x)Ba(Lu1/2Nb1/2)O3-xPbTiO3 solid solution with morphotropic phase boundary

A new ferroelectric solid solution of (1 − x)Ba(Lu_1/2Nb_1/2)O₃-xPbTiO₃ (BLN-PT) (0 ≤ x ≤ 1) has been synthesized by solid state reactions. Its structure and electric properties have been studied by X-ray diffraction and di-/ferro-electric measurements. Based on the investigation, a partial solid state phase diagram of the binary BLN-PT ceramics system has been established, which exhibits a morphotropic phase boundary (MPB) region in the composition range of 0.64 ≤ x ≤ 0.68. The Curie temperature is measured to be around 250 °C in the vicinity of the MPB region, which is much higher than that of PMNT or PZNT system. The dielectric behavior has been discussed based on Curie-Weiss Law and Lorentz-type quadratic relationship. With increasing PT content, a transformation from relaxor to ferroelectric phase has been demonstrated in the solid solution system.     

Textural and pseudocapacitive characteristics of sol-gel derived RuO2·xH2O: Hydrothermal annealing vs. annealing in air

Hydrous ruthenium dioxide (RuO₂·xH₂O) prepared in a modified sol-gel process was subjected to annealing in air and water at various temperatures for supercapacitor applications. The textural and pseudocapacitive characteristics of RuO₂·xH₂O annealed in air and water were systematically compared to show the benefits of annealing in water (denoted as hydrothermal annealing). An important concept that hydrothermal annealing effectively restricts condensation of hydroxyl groups within nanoparticles, inhibits crystal growth, and maintains high water content of RuO₂·xH₂O is demonstrated in this work. The unique textural characteristics of hydrothermally annealed RuO₂·xH₂O are attributable to the high-pressured, water-enriched surroundings which restrain coalescence of RuO₂·xH₂O nanocrystallites. The crystalline, hydrous nature of hydrothermally annealed RuO₂·xH₂O favors the utilization of active species in addition to a merit of minor dependence of specific capacitance on the scan rate of CV for pseudocapacitors. As a result, RuO₂·xH₂O with hydrothermal annealing at 225 °C for 24 h exhibits 16 wt.% water, an average particle size of about 7 nm, and specific capacitance of ca. 390 F g⁻¹.     

Oxygen and chlorine evolution on RuO2 + TiO2 + CeO2 + Nb2O5 mixed oxide electrodes

A systematic investigation was conducted on the mechanism and electrocatalytic properties of O₂ and Cl₂ evolution on mixed oxide electrodes of nominal composition: Ti/[Ru_(0.3)Ti_(0.6)Ce_(0.1−x)]O₂[Nb₂O₅]_(x) (0 ≤ x ≤ 0.1). For the oxygen evolution, a 30 mV Tafel slope is obtained in the presence of CeO₂, while in its absence a 40 mV coefficient is observed. The intrinsic electrocatalytic activity is mainly due to electronic factors, as result of the synergism between Ru and Ce oxides. For chlorine evolution, the Tafel slope (30 mV) is independent on oxide composition. The best global electrocatalytic activity for ClER was observed in the absence of Nb₂O₅ additive. Variation of the voltammetric charge throughout the experiments confirms high CeO₂ content compositions are fragile, due mainly to the porosity caused by CeO₂ presence. On the other hand, Nb₂O₅ addition decreases considerably this instability.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Single crystal nanobelts of V3O7·H2O: A lithium intercalation host with a large capacity

In this study, single crystal V₃O₇·H₂O nanobelts were successfully synthesized using a simple hydrothermal route, in which templates or catalysts were absent. The synthesized V₃O₇·H₂O nanobelts are highly crystalline and have lengths up to several tens of micrometers. The width and thickness of the nanobelts are found to be about 30-50 and 30 nm, respectively. A lithium battery using V₃O₇·H₂O nanobelts as the positive electrode exhibits a high initial discharge capacity of 409 mAh g⁻¹, corresponding to the formation of Li_xV₃O₇·H₂O (x = 4.32). Such a high degree of electrochemical performance is attributed to the intrinsic properties of the single-crystalline V₃O₇·H₂O nanobelts.     

Preparation and cycling performance of Aland F co-substituted compounds Li4AlxTi5−xFyO12−y

Li₄Al_xTi_5−xF_yO_12−y compounds were prepared by a solid-state reaction method. Phase analyses demonstrated that both Al³⁺ and F⁻ ions entered the structure of spinel-type Li₄Ti₅O₁₂. Charge-discharge cycling results at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.5 and 0.5 V showed that the Al³⁺ and F⁻ substitutions improved the first total discharge capacity of Li₄Ti₅O₁₂. However, Al³⁺ substitution greatly increased the reversible capacity and cycling stability of Li₄Ti₅O₁₂ while F⁻ substitution decreased its reversible capacity and cycling stability slightly. The electrochemical performance of the Al³⁺-F⁻-co-substituted specimen was better than the F⁻-substituted one but worse than the Al³⁺-substituted one.     

Synthesis and tunable thermal expansion properties of Sc2−xYxW3O12 solid solutions

A new series of rare earth solid solutions Sc_2−xY_xW₃O₁₂ was successfully synthesized by the conventional solid-state method. Effects of doping ion yttrium on the crystal structure, morphology and thermal expansion property of as-prepared Sc_2−xY_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TG), field emission scanning electron microscope (FE-SEM) and thermal mechanical analyzer (TMA). Results indicate that the obtained Sc_2−xY_xW₃O₁₂ samples with Y doping of 0≤x≤0.5 are in the form of orthorhombic Sc₂W₃O₁₂-structure and show negative thermal expansion (NTE) from room temperature to 600 °C; while as-synthesized materials with Y doping of 1.5≤x≤2 take hygroscopic Y₂W₃O₁₂·nH₂O-structure at room temperature and exhibit NTE only after losing water molecules. It is suggested that the obvious difference in crystal structure leads to different thermal expansion behaviors in Sc_2−xY_xW₃O₁₂. Thus it is proposed that thermal expansion properties of Sc_2−xY_xW₃O₁₂ can be adjusted by the employment of Y dopant; the obtained Sc_1.5Y_0.5W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.00683×10⁻⁶ °C⁻¹ in the 25–250 °C range.