Molybdenum L-shell X-ray production by 350-600 keV Xe (q = 25-30) ions

Molybdenum L-shell X-rays were produced by Xe^q+ (q = 25-30) bombardment at low energies from 2.65 to 4.55 keV/amu (350-600 keV). We observed a kinetic energy threshold of Mo L-shell ionization down to 2.65-3.03 keV/amu (350-400 keV). The charge state effect of the incident ions was not observed which shows that the ions were neutralized, reaching an equilibrium charge state and losing their initial charge state memory before production of L-shell vacancies resulted in X-ray production. The experimental ionization cross sections were compared with those from Binary Encounter Approximation theory. Taking into account projectile deflection in the target nuclear Coulomb field, the ionization cross section of Mo L-shell near the kinetic energy threshold was well described.     

Separation of potential and kinetic electron emission from Si and W induced by multiply charged neon and argon ions

The total secondary electron emission yields, γ_T, induced by impact of the fast ions Ne^q+ (q = 2-8) and Ar^q+ (q = 3-12) on Si and Ne^q+ (q = 2-8) on W targets have been measured. It was observed that for a given impact energy, γ_T increases with the charge of projectile ion. By plotting γ_T as a function of the total potential energy of the respective ion, true kinetic and potential electron yields have been obtained. Potential electron yield was proportional to the total potential energy of the projectile ion. However, decrease in potential electron yield with increasing kinetic energy of Ne^q+ impact on Si and W was observed. This decrease in potential electron yield with kinetic energy of the ion was more pronounced for the projectile ions having higher charge states. Moreover, kinetic electron yield to energy-loss ratio for various ion-target combinations was calculated and results were in good agreement with semi-empirical model for kinetic electron emission.     

Guiding of argon ions through a tapered glass capillary

We report results from our recent experiments on guiding of Ar⁸⁺ ions through a single tapered glass capillary with an inlet diameter of 1 mm, an outlet diameter of 0.15 mm and a length of 45 mm. The profile width of the transmitted ion beam and the guiding power of the used glass capillary has been measured at a kinetic energy in the range of 8 keV up to 60 keV using a position sensitive detector. The charge up of the capillary and the evolution of the guiding effect is shown for a tilt angle of Ψ = 4°. The charge up of the inner walls of the tapered glass capillary causes a compression of the incident ion beam by a factor of 8. We found high guiding angles and small profile width of the transmitted ion beam in comparison to the transmission of highly charged ions through nanocapillaries in thin foils. A suppression of the transmission at small tilt angles and low kinetic energies has been observed.     

Proton beam induced luminescence of silicon dioxide implanted with silicon

Light emission from a silicon dioxide layer enriched with silicon has been studied. Samples used had structures made on thermally oxidized silicon substrate wafers. Excess silicon atoms were introduced into a 250-nm-thick silicon dioxide layer via implantation of 60 keV Si⁺ ions up to a fluence of 2 × 10¹⁷ cm⁻². A 15-nm-thick Au layer was used as a top semitransparent electrode. Continuous blue light emission was observed under DC polarization of the structure at 8-12 MV/cm. The blue light emission from the structures was also observed in an ionoluminescence experiment, in which the light emission was caused by irradiation with a H₂⁺ ion beam of energy between 22 and 100 keV. In the case of H₂⁺, on entering the material the ions dissociated into two protons, each carrying on average half of the incident ion energy. The spectra of the emitted light and the dependence of ionoluminescence on proton energy were analyzed and the results were correlated with the concentration profile of implanted silicon atoms.     

Electron excitation cross sections of atomic hydrogen by fully stripped projectile ions

Electron excitation of atomic hydrogen by fully stripped projectile ions (q = 1-8) is theoretically studied by using the boundary corrected continuum intermediate state approximation in the energy range of 20-1000 keV/amu. In this formalism, we have taken a distortion effect produced by the projectile charge. The present computed results for the excited states (n = 2, 3, 4) of hydrogen atom with proton impact is only compared with experiments and other theoretical results. In addition, other results for different charge states (q = 1-8) are displayed in tabular form to get a detail view of contribution from different sub-shells. We have also studied the behavior of saturation of the cross sections which should tend to a constant value as the projectile charge increase.     

Desorption of gold nanoclusters from gold nanodispersed targets by 200 keV Au5 polyatomic ions in the elastic stopping mode: Experiment and molecular-dynamics simulation

Au nanoislet targets (∅ 2-60 nm) were bombarded by 200 keV polyatomic ions (40 keV/atom), which deposit their energy mainly in the nuclear stopping mode: ∑(dE/dx)_n = 30 keV/nm and ∑(dE/dx)_e = 2 keV/nm. The matter desorbed in the form of nanoclusters was registered by TEM. The total transfer of matter was determined by neutron-activation analysis. The total yield of the ejected gold reached high values of up to 2.6 × 10⁴ atoms per Au₅ ion. The major part (2 × 10⁴ atoms per ion Au₅) of the emission is in the form of nanoclusters. The results are compared with the data of similar experiments with 1 MeV Au₅ (200 keV/atom) and other projectiles. The analysis of the experimental data and the comparison to molecular-dynamics simulation results of the desorption process show that the desorption of Au nanoislets is induced by their melting, build-up of pressure and thermal expansion.     

Guiding and blocking of highly charged ions through a single glass capillary

Highly charged ions produced in an electron beam ion trap, I^q+, q = 10-50, were transmitted through a tapered glass capillary having diameter of at the end. We found that for a particular beam current, there exists an optimum tilting angle of the capillary in which a steady output of ions is observed, while for smaller angles, the ion counts first rise, then gradually decay on a time scale of minutes. In the case of steady transmission, the charge state distribution is found to be slightly towards the lower side.     

Study of ion emission from a germanium crystal surface under impact of fast Pb ions in channeling conditions

A thin germanium crystal has been irradiated at GANIL by Pb beams of 29 MeV/A (charge state Q_in = 56 and 72) and of 5.6 MeV/A (Q_in = 28). The induced ion emission from the sample entrance surface was studied, impact per impact, as a function of Q_in, velocity v_in and energy loss ΔE in the crystal. The Pb ions transmitted through the crystal were analyzed in charge (Q_out) and energy using the SPEG spectrometer. The emitted ionized species were detected and analyzed in mass by a time-Of-flight multianode detector (LAG). Channeling was used to select peculiar ΔE values in Ge and hence peculiar Pb ion trajectories close to the emitting entrance surface. The experiment was performed in standard vacuum. No Ge emission was found. The dominating emitted species are H⁺ and hydrocarbon ions originating from the contamination layer on top of the crystal. The mean value 〈M〉 of the number of detected species per incoming Pb ion (multiplicity) varies as (Q_in/v_in)^p, with p values in agreement with previous results. We have clearly observed an influence of the energy deposition ΔE in Ge on the emission from the top contamination layer. When selecting increasing values of ΔE, we observed a rather slow increase of 〈M〉. On the contrary, the probabilities of high multiplicity values, which are essentially connected to fragmentation after emission, strongly increase with ΔE.     

Optical emission from Be, Cu and CuBe targets during ion beam sputtering

A spectral structure of the radiation (190-590 nm) emitted during sputtering of polycrystalline Cu, Be and CuBe targets by Kr⁺ ions with 5 keV have been presented. Evolution of surface composition during ion beam sputtering is investigated. Several time scales are distinguished, corresponding to different processes: the elimination of surface contaminants, the removal of the corroded layer. The implications for the use of ion beam optical spectroscopy in surface analysis are discussed. In the case of Be and Cu98 Be2, a molecular structure appears between 492 nm and 502 nm. It is similar for both samples and is ascribed to de-excitation of BeH.     

Cross sections for transfer ionization in ion-helium collisions

A simple model has been developed within the independent-particle model (IPM) based on the Bohr-Lindhard model and classical statistical model. Cross sections for transfer ionization of helium by ions A^q+ (q = 1-3) are calculated for impact energies between 10 and 6000 keV/u. The calculated cross sections are in good agreement with the experimental data of helium by He^(1-2)+ and Li^(1-3)+.     

Desorption of gold nanoclusters (2-30 nm) under low excitation of their electronic subsystem by Ar ions (14 keV/nm)

Gold nanodispersed targets with islands-grains sized 2-30 nm were irradiated by Ar⁷⁺ ions with the energy of 45.5 MeV and (dE/dx)_e = 14.2 keV/nm in gold. The desorbed gold nanoclusters were studied by TEM method. For all the targets desorption of intact gold nanoclusters is observed. However, for inelastic stopping of monatomic Ar ions in gold of 14.2 keV/nm desorption of nanoclusters is observed only up to ∼25 nm. The yield of the desorbed nanoclusters considerably decreases from 3 to 0.02 cluster/ion with the increase of the mean size of the desorbed nanoclusters from 3 to 14.2 nm. The results are discussed.     

PL and XPS study of radiation damage created by various slow highly charged heavy ions on GaN epitaxial layers

Photoluminescence (PL) spectrum, in conjunction with X-ray photoelectron spectroscopy (XPS) is used to evaluate the surface damage of GaN layer by highly-charged Xe^q+ (18 ? q ? 30), Ar^q+ (6 ? q ? 16) and Pb^q+ (q = 25,35) ions. The intensity of PL emission of GaN layer, including near band-edge peak and yellow luminescence, decreases with increasing fluence and charge state of the incident ions. Finally the PL emission is completely quenched after irradiation to high fluences at high charge state. A new peak at 450 nm appeared in PL spectra of the specimens irradiated with Xe¹⁸⁺, Ar⁶⁺ and Ar¹¹⁺, indicating that radioactive recombination within donor-acceptor pairs (DAPs) during irradiation. After irradiation, XPS spectra show N deficient or Ga rich on GaN surface and XPS spectra of Ga3d core levels indicate spectral peak evidently shifts from a Ga-N to Ga-Ga and Ga-O bond. The relative content of Ga-N bond decreases and the content of Ga-Ga bond increases with the increase of ion fluence and ion charge state. The binding energy of Ga3d_5/2 electron corresponding to Ga-Ga bond of the irradiated GaN film is found to be smaller than that of metallic Gallium (Ga⁰), which can be attributed to irradiation damage.     

Visible light emission from silicon dioxide with implanted excess silicon

Light emission from silicon dioxide doped with excess silicon by silicon ion implantation was investigated. Photoluminescence of silicon dioxide after silicon ion implantation and subsequent annealing at temperatures exceeding 1000 °C was observed. Excitation with monochromatic light with wavelength ranging from λ = 488 nm to λ = 266 nm leads to wide wavelength band emission ranging from about 650 nm up to about 850 nm with a maximum located at about 750 nm. This red/infrared photoemission is attributed to silicon nanocrystals created in silicon dioxide matrix. However, the same material used in electroluminescent experiments emitted blue and green light as well. In this paper the results of photo- and ionoluminescence experiments will be presented. The interest of the paper is focused on the problem of identification of different regions in the structure responsible for light emission of different wavelengths.     

Proton sputtering from polycrystalline Al surface interacting with highly charged ions at grazing incidence angle

Sputtering processes of protons from a polycrystalline Al surface interacting with Ar^q+ (q = 3-14) ions at a grazing incidence angle (∼0.5°) were investigated. The intensity of protons (I_H) detected in coincidence with scattered Ar atoms was measured as a function of q. I_H saturated at q ? 10, although it increased rapidly with q at 3 ? q ? 8. The angular distribution of protons with low kinetic energy (?2 eV) began to deviate from the cosine distribution and assumed a rather flat equidistribution as q increased. To analyze the sputtering processes of protons at the grazing incidence angle, a modified model of the “above-surface potential sputtering model” was proposed by considering image acceleration of projectile ions.     

Pure ionization cross section of helium and ionization mechanism

Pure target ionization was investigated for 0.4-6.4 MeV C^q+(q = 1-4) + He and O^q+(q = 1-4) + He collisions. The double-to-single target ionization ratios R₂₁ were measured using coincidence techniques. We compare our results with existing experimental results and find they are in good agreement. The ratio R₂₁ is nearly independent of projectile charge state. The relation of R₂₁ ∼ V is analyzed using the over barrier model (OBM) and ionization probability, which is described in our extended over barrier model. Our calculation agrees well with the experimental results.     

A high charge state all-permanent magnet ECR ion source for the IMP 320 kV HV platform

A 320 kV high voltage (HV) platform has been constructed at Institute of Modern Physics (IMP) to satisfy the increasing requirements of experimental studies in some heavy ion associated directions. A high charge state all-permanent magnet ECRIS-LAPECR2 has been designed and fabricated to provide intense multiple charge state ion beams (such as 1000 eμA O⁶⁺, 16.7 eμA Ar¹⁴⁺, 24 eμA Xe²⁷⁺, etc.) for the HV platform. LAPECR2 has a dimension of ∅ 650 mm × 560 mm. The powerful 3D magnetic confinement to the ECR plasma and the optimum designed magnetic field for the operation at 14.5 GHz makes it possible to obtain very good performances from this source. After a brief introduction of the ECRIS and accelerator development at IMP, the conceptual design of LAPECR2 source is presented. The first test results of this all-permanent magnet ECRIS are given in this paper.     

Monte Carlo study of ion-induced backward and forward secondary electron emission from thin Al foil

A direct Monte Carlo program has been developed to calculate the backward (γ_b) and forward (γ_f) electron emission yields from 20 nm thick Al foil for impact of C⁺, Al⁺, Ar⁺, Cu⁺ and Kr⁺ ions having energies in the range of 0.1-10 keV/amu. The program incorporates the excitation of target electrons by projectile ions, recoiling target atoms and fast primary electrons. The program can be used to calculate the electron yields, distribution of electron excitation points in the target and other physical parameters of the emitted electrons. The calculated backward electron emission yield and the Meckbach factor R = γ_f/γ_b are compared with the available experimental data, and a good agreement is found. In addition, the effect of projectile energy and mass on the longitudinal and lateral distribution of the excitation points of the electrons emitted from front and back of Al target has been investigated.     

Properties of Na implanted targets

Ten types of ²³Na implanted targets have been fabricated for the purposes of investigating the effects of proton beam bombardment on the implanted sodium distribution. Targets were implanted at energies of E_Na = 10-30 keV using copper, tantalum, and nickel as host materials. Thin layers (100-200 Å) of chromium and gold were also evaporated over some of the targets to provide a protective layer for the implanted sodium. The ²³Na(p, γ) resonance at a lab proton energy of E_p = 309 keV was used to determine the implanted distribution. Successive resonance profile measurements are presented for each implanted target, and the concurrent loss of ²³Na resulting from beam bombardment is reported. The calculated temperature rise of the targets indicates that beam heating has a negligible effect on the implanted sodium distribution, and that the principal mechanism for ²³Na loss during beam bombardment is sputtering.     

Sputtering and crystalline structure modification of bismuth thin films deposited onto silicon substrates under the impact of 20-160 keV Ar ions

The sputtering of bismuth thin films induced by 20-160 keV Ar⁺ ions has been studied using Rutherford backscattering spectrometry, scanning electron microscopy and X-ray energy dispersive and diffraction spectroscopy. These techniques revealed increasing modifications of the Bi film surfaces with increasing both ion beam energy and fluence up to their complete deterioration under irradiation conditions E = 160 keV and φ = 1.5 × 10¹⁶ cm⁻², leaving isolated islands of preferred (0 1 2) orientation on the Si substrate. The observed surface morphology and crystalline structure evolutions are likely due to a complex interplay of interaction mechanisms involving both elastic nuclear collisions and inelastic electronic ones. The measured Bi sputtering yields versus Ar⁺ ion fluence for a fixed ion energy exhibit a significant depression at very low φ-values followed by a steady state regime above ∼2.0 × 10¹⁴ cm⁻². Measured sputtering yields versus Ar⁺ ion energy with fixing ion fluence to 1.2 × 10¹⁶ cm⁻² in the upper part of the yield saturation regime are also reported. Their comparison to theoretical model and SRIM 2008 Monte Carlo simulation predictions is discussed.     

Alkali ion scattering from Ag(0 0 1) and Ag thin films at low and hyperthermal energies

We have investigated the scattering of K⁺ and Cs⁺ ions from a single crystal Ag(0 0 1) surface and from a Ag-Si(1 0 0) Schottky diode structure. For the K⁺ ions, incident energies of 25 eV to 1 keV were used to obtain energy-resolved spectra of scattered ions at θ_i = θ_f = 45°. These results are compared to the classical trajectory simulation safari and show features indicative of light atom-surface scattering where sequential binary collisions can describe the observed energy loss spectra. Energy-resolved spectra obtained for Cs⁺ ions at incident energies of 75 eV and 200 eV also show features consistent with binary collisions. However, for this heavy atom-surface scattering system, the dominant trajectory type involves at least two surface atoms, as large angular deflections are not classically allowed for any single scattering event. In addition, a significant deviation from the classical double-collision prediction is observed for incident energies around 100 eV, and molecular dynamics studies are proposed to investigate the role of collective lattice effects. Data are also presented for the scattering of K⁺ ions from a Schottky diode structure, which is a prototype device for the development of active targets to probe energy loss at a surface.