Analytical performance of polymer-based microfluidic devices fabricated by computer numerical controlled machining

A study comparing the electrophoretic separation performance attainable from microchips molded by masters fabricated using conventional CNC machining techniques with commercial microchips, wire imprinted microchips, and microchips from LIGA molding devices is presented. An electrophoresis-based detection system using fluorescence microscopy was used to determine the analytical utility of these microchips. The separation performance of CNC microchips was comparable to commercially available microchips as well as those fabricated from LIGA masters. The important feature of the CNC machined masters is that they have rapid design-to-device times using routinely available machining tools. This low-cost prototyping approach provides a new entry point for researchers interested in thermoplastic microchips and can accelerate the development of polymer-based lab-on-a-chip devices.     

Probes for detection of specific DNA sequences at the single-molecule level

A method has been developed for highly sensitive detection of specific DNA sequences in a homogeneous assay using labeled oligonucleotide molecules in combination with single-molecule photon burst counting and identification. The fluorescently labeled oligonucleotides are called smart probes because they report the presence of complementary target sequences by a strong increase in fluorescence intensity. The smart probes consist of a fluorescent dye attached at the terminus of a hairpin oligonucleotide. The presented technique takes advantage of the fact that the used oxazine dye JA242 is efficiently quenched by complementary guanosine residues. Upon specific hybridization to the target DNA, the smart probe undergoes a conformational change that forces the fluorescent dye and the guanosine residues apart, thereby increasing the fluorescence intensity about six fold in ensemble measurements. To increase the detection sensitivity below the nanomolar range, a confocal fluorescence microscope was used to observe the fluorescence bursts from individual smart probes in the presence and absence of target DNA as they passed through the focused laser beam. Smart probes were excited by a pulsed diode laser emitting at 635 nm with a repetition rate of 64 MHz. Each fluorescence burst was identified by three independent parameters: (a) the burst size, (b) the burst duration, and (c) the fluorescence lifetime. Through the use of this multiparameter analysis, higher discrimination accuracies between smart probes and hybridized probe-target duplexes were achieved. The presented multiparameter detection technique permits the identification of picomolar target DNA concentrations in a homogeneous assay, i.e., the detection of specific DNA sequences in a 200-fold excess of labeled probe molecules.     

Fluorescence detection of DNA, adenosine-5'-triphosphate (ATP), and telomerase activity by zinc(II)-protoporphyrin IX/G-quadruplex labels

The zinc(II)-protoporphyrin IX (ZnPPIX) fluorophore binds to G-quadruplexes, and this results in the enhanced fluorescence of the fluorophore. This property enabled the development of DNA sensors, aptasensors, and a sensor following telomerase activity. The DNA sensor is based on the design of a hairpin structure that includes a "caged" inactive G-quadruplex sequence. Upon opening the hairpin by the analyte DNA, the resulting fluorescence of the ZnPPIX/G-quadruplex provides the readout signal for the sensing event (detection limit 5 nM). Addition of Exonuclease III to the system allows the recycling of the analyte and its amplified analysis (detection limit, 200 pM). The association of the ZnPPIX to G-quadruplex aptamer-substrate complexes allowed the detection of adenosine-5'-triphosphate (ATP, detection limit 10 μM). Finally, the association of ZnPPIX to the G-quadruplex repeat units of telomers allowed the detection of telomerase activity originating from 380 ± 20 cancer 293T cell extract.     

Single-quantum-dot-based DNA nanosensor

Rapid and highly sensitive detection of DNA is critical in diagnosing genetic diseases. Conventional approaches often rely on cumbersome, semi-quantitative amplification of target DNA to improve detection sensitivity. In addition, most DNA detection systems (microarrays, for example), regardless of their need for target amplification, require separation of unhybridized DNA strands from hybridized stands immobilized on a solid substrate, and are thereby complicated by solution-surface binding kinetics. Here, we report an ultrasensitive nanosensor based on fluorescence resonance energy transfer (FRET) capable of detecting low concentrations of DNA in a separation-free format. This system uses quantum dots (QDs) linked to DNA probes to capture DNA targets. The target strand binds to a dye-labelled reporter strand thus forming a FRET donor-acceptor ensemble. The QD also functions as a concentrator that amplifies the target signal by confining several targets in a nanoscale domain. Unbound nanosensors produce near-zero background fluorescence, but on binding to even a small amount of target DNA (approximately 50 copies or less) they generate a very distinct FRET signal. A nanosensor-based oligonucleotide ligation assay has been demonstrated to successfully detect a point mutation typical of some ovarian tumours in clinical samples.     

Fluorescently imaged particle counting immunoassay for sensitive detection of DNA modifications

Modifications of genomic DNA may change gene expression and cause adverse health effects. Here we for the first time demonstrate a particle counting immunoassay for rapid and sensitive detection of DNA modifications using benzo[a]pyrenediol epoxide (BPDE)-DNA adducts as an example. The BPDE-adducted DNA is specifically captured by immunomagnetic particles and then isolated from unmodified DNA by applying an external magnetic field. By taking advantage of the fluorescence signal amplification through multiple labeling of captured DNA by OliGreen dye, the captured BPDE-DNA adducts can be quantified by particle counting from fluorescence imaging. This clearly demonstrates that the number of fluorescently countable particles is proportional to the modification content in genomic DNA. It is interesting to note that the background fluorescence signal caused by nonspecific adsorption of OliGreen dye can be more effectively quenched than that induced by the binding of OliGreen dye to ssDNA, allowing for significant reduction in the background fluorescence and further enhancing the detection sensitivity. The developed method can detect trace BPDE-DNA adducts as low as 180 fM in the presence of 1 billion times more normal nucleotides in genomic DNA and has a dynamic range over 4 orders of magnitude. By using anti-5-methylcytosine antibody, the method is extended to the detection of global DNA methylation. With high sensitivity and specificity, this rapid and easy-to-perform analytical method for DNA modifications shows a broad spectrum of potential applications in genotoxical and epigenetic analysis.     

Single molecule fluorescence burst detection of DNA fragments separated by capillary electrophoresis.

A method has been developed for detecting DNA separated by capillary gel electrophoresis (CGE) using single molecule photon burst counting. A confocal fluorescence microscope was used to observe the fluorescence bursts from single molecules of DNA multiply labeled with the thiazole orange derivative T06 as they passed through the approximately 2 micrometer diameter focused laser beam. Amplified photoelectron pulses from the photomultiplier are grouped into bins of 360-450 micros in duration, and the resulting histogram is stored in a computer for analysis. Solutions of M13 DNA were first flowed through the capillary at various concentrations, and the resulting data were used to optimize the parameters for digital filtering using a low-pass Fourier filter, selecting a discriminator level for peak detection, and applying a peak-calling algorithm. Statistical analyses showed that (i) the number of M13 molecules counted versus concentration was linear with slope = 1, (ii) the average burst duration was consistent with the expected transit time of a single molecule through the laser beam, and (iii) the number of detected molecules was consistent with single molecule detection. The optimized single molecule counting method was then applied to an electrophoretic separation of M13 DNA and to a separation of pBR 322 DNA from pRL 277 DNA. Clusters of discreet fluorescence bursts were observed at the expected appearance time of each DNA band. The autocorrelation function of these data indicated transit times that were consistent with the observed electrophoretic velocity. These separations were easily detected when only 50-100 molecules of DNA per band traveled through the detection region. This new detection technology should lead to the routine analysis of DNA in capillary columns with an on-column sensitivity of approximately 100 DNA molecules/band or better.     

Fluorescence energy transfer between fluorescein label and DNA intercalators to detect nucleic acids hybridization in homogeneous media

A general approach to detecting nucleic acid sequences in homogeneous media by means of steady-state fluorescence measurements is proposed. The methodology combines the use of a fluorescence-labeled single-strand DNA model probe, the complementary single-strand DNA target, and a DNA intercalator. The probe was fluorescein labeled to a spacer arm at the N4 position of the cytosine amino groups in polyribocytidylic acid (5'), poly(C), which acts as a model DNA probe. The complementary strand was polyriboinosinic acid (5'), poly(I), as a model of the target, and the energy transfer acceptor was an intercalator, either ethidium bromide or ethidium homodimer. In previous papers we have shown that the fluorescence intensity of the fluorescein label decreases when labeled poly(C) hybridizes with poly(I), and this fluorescence quenching can be used to detect DNA hybridization or renaturation in homogeneous media. In this paper we demonstrate that fluorescence resonance energy transfer (FRET) between fluorescein labeled to poly(C) and an intercalator agent takes place when single-stranded poly(C) hybridizes with poly(I), and we show how the fluorescence energy transfer further decreases the steady-state fluorescence intensity of the label, thus increasing the detection limit of the method. The main aim of this work was to develop a truly homogeneous detection system for specific nucleic acid hybridization in solution using steady-state fluorescence and FRET, but with the advantage of only having to label the probe with the energy donor since the energy acceptor is intercalated spontaneously. Moreover, the site label is not critical and can be labeled randomly in the DNA strand. Thus, the method is simpler than those published previously based on FRET. The experiments were carried out in both direct and competitive formats.     

Fluorescence turn-on detection of DNA and label-free fluorescence nuclease assay based on the aggregation-induced emission of silole

By making use of the aggregation-induced emission feature of silole, compound 1 with an ammonium group is designed and synthesized with a view to developing a new optical probe for fluorescence turn-on detection of DNA and label-free fluorescence nuclease assay. The fluorescence of 1 increases largely upon mixing with DNA, in particular for long DNA, indicating that 1 can be used for fluorescence turn-on detection of DNA. More interestingly, 1 can be employed to follow the DNA cleavage process by nuclease. Therefore, a label-free fluorescence nuclease assay method is successfully established with 1. Furthermore, this label-free fluorescence assay can also be used for inhibitor screening of nucleases. Given its simplicity, easy operation, sensitivity and cost-effectiveness, this method can be extended to other nuclease assays and high-throughput screening of nuclease inhibitors.     

Label-free detection of DNA-binding proteins based on microfluidic solid-state molecular beacon sensor

A solid-state molecular beacon using a gold support as a fluorescence quencher is combined with a polydimethylsiloxane (PDMS) microfluidic channel to construct an optical sensor for detecting single-stranded DNA binding protein (SSBP) and histone protein. The single-stranded DNA-Cy3 probe or double-stranded DNA-Cy3 probe immobilized on the gold surface is prepared for the detection of SSBP or histone, respectively. Due to the different quenching ability of gold to the immobilized single-stranded DNA-Cy3 probe and the immobilized double-stranded DNA-Cy3 probe, low fluorescence intensity of the attached single-stranded DNA-Cy3 is obtained in SSBP detection, whereas high fluorescence intensity of the attached double-stranded DNA-Cy3 is obtained in histone detection. The amounts of SSBP in sample solutions are determined from the degree of fluorescence recovery of the immobilized single-stranded DNA-Cy3 probe, whereas that of histone in sample solutions is determined from the degree of fluorescence quenching of the immobilized double-stranded DNA-Cy3 probe. Using this approach, label-free detection of target proteins at nanomolar concentrations is achieved in a convenient, general, continuous flow format. Our approach has high potential for the highly sensitive label-free detection of various proteins based on binding-induced conformation changes of immobilized DNA probes.     

Time-resolved fluorescence detection of mosaic DNA chip

We demonstrated a time-resolved fluorescence (TRF) label and detection of mosaic DNA chip in this paper. We synthesized oligonucleotide sequences in situ on glass slides directly, and then sliced them up into small pieces and patched up the pieces bearing different sequences to generate a mosaic DNA chip. With multiple 4, 7-bis(chlorosulfophenyl)-1, 10-phenanthroline-2, 9-dicarboxylic acid (BCPDA, abbreviated as BCPDA) labeling method based on avidin-biotin amplification, we established a TRF detection format on the mosaic DNA chip. The detection method allows discriminatory signals for perfect match, one-base mismatch, two-base mismatch, and three-base mismatch by TRF labeled DNA hybridization, whereby Europium (III, Eu3+) was captured and released on the principle of complexation and dissociation interaction between BCPDA and Eu3+ solution when the BCPDA-tagged avidin and biotin-capped oligonucleotide sequence linked. The fluorescence spectra and related lifetimes were determined. We also compared the TRF detection mode with the conventional fluorescence one. These results showed the former is a potential alternative replacement of the latter, especially for labeling the mosaic DNA chip. The discovery is of fundamental interest and has significant implications to biochips and biosensors based on time-resolved-fluorescence detection.     

Pd nanowires as new biosensing materials for magnified fluorescent detection of nucleic acid

The designed synthesis of new nanomaterials with controlled shape, composition, and structure is critical for tuning their physical and chemical properties, and further developing interesting analytical sensing devices. Herein, we presented that Pd nanowires (NWs) can be used as a new biosensing platform for high-sensitivity nucleic acid detection. The general sensing concept is based on the fact that Pd NWs can adsorb the fluorescently labeled single-stranded DNA probe and lead to substantial fluorescence quenching of dye, followed by specific hybridization with the complementary region of the target DNA sequence. This results in desorption of double-stranded DNA from Pd NWs surface and subsequent recovery of fluorescence. Furthermore, an amplification strategy based on Pd NWs for nucleic acid detection by using exonuclease III (Exo III) was demonstrated. The present dual-magnification sensing system combined Pd NWs with Exo III has a detection range of 1.0 nM to 2.0 μM with the detection limit of 0.3 nM (S/N = 3), which is about 20-fold higher than that of traditional unamplified homogeneous assays.     

Efficient detection of single DNA fragments in flowing sample streams by two-photon fluorescence excitation

This paper reports the demonstration of efficient single molecule detection in flow cytometry by two-photon fluorescence excitation. We have used two-photon excitation (TPE) to detect single DNA fragments as small as 383 base pairs (bp) labeled with the intercalating dye, POPO-1, at a dye:nucleotide ratio of 1:5. TPE of the dye-DNA complexes was accomplished using a mode-locked, 120 fs pulse width Ti:sapphire laser operating at 810 nm. POPO-1 labeled DNA fragments of 1.1 kilobase pairs (kbp) and larger were sequentially detected in our flow cytometry system with a detection efficiency of nearly 100%. The detection efficiency for the 383 bp DNA fragments was approximately 75%. We also demonstrate the ability to distinguish between different sized DNA fragments in a mixture by their individual fluorescence burst sizes by TPE. These studies indicate that using TPE for single molecule flow cytometry experiments lowers the intensity of the background radiation by approximately an order of magnitude compared to one-photon excitation, due to the large separation between the excitation and emission wavelengths in TPE.     

Binding-induced fluorescence turn-on assay using aptamer-functionalized silver nanocluster DNA probes

We present here a binding-induced fluorescence turn-on assay for protein detection. Key features of this assay include affinity binding-induced DNA hybridization and fluorescence enhancement of silver nanoclusters (Ag NCs) using guanine-rich DNA sequences. In an example of an assay for human α-thrombin, two aptamers (Apt15 and Apt29) were used and were modified by including additional sequence elements. A 12-nucleotide (nt) sequence was used to link the first aptamer with a nanocluster nucleation sequence at the 5'-end. The second aptamer was linked through a complementary sequence (12-nt) to a G-rich overhang at the 3'-end. Binding of the two aptamer probes to the target protein initiates hybridization between the complementary linker sequences attached to each aptamer and thereby bring the end of the G-rich overhang to close proximity to Ag NCs, resulting in a significant fluorescence enhancement. With this approach, a detection limit of 1 nM and a linear dynamic range of 5 nM-2 μM were achieved for human α-thrombin. This fluorescence assay is performed in a single tube, and it does not require washing or separation steps. The principle of the binding-induced DNA hybridization and fluorescence enhancement of Ag NCs can be extended to other homogeneous assay applications provided that two appropriate probes are available to bind with the same target molecule.     

Few‐Layer Graphdiyne Nanosheets Applied for Multiplexed Real‐Time DNA Detection

Despite recent progress in 2D nanomaterials‐based biosensing, it remains challenging to achieve sensitive and high selective detection. This study develops few‐layer graphdiyne (GD) nanosheets (NSs) that are used as novel sensing platforms for a variety of fluorophores real‐time detection of DNA with low background and high signal‐to‐noise ratio, which show a distinguished fluorescence quenching ability and different affinities toward single‐stranded DNA and double‐stranded DNA. Importantly, for the first time, a few‐layer GD NSs‐based multiplexed DNA sensor is developed.     

Coordination polymer nanobelts for nucleic acid detection

Herein, coordination polymer nanobelts (CPNBs) were prepared rapidly and on a large scale, by directly mixing aqueous AgNO(3) solution and an ethanol solution of 4, 4'-bipyridine at room temperature. The application of such CPNBs as a fluorescent sensing platform for nucleic acid detection was further explored. CPNB is a π-rich structure, the strong π-π stacking interactions between unpaired DNA bases and CPNB leads to adsorption of fluorescently labeled single-stranded DNA (ssDNA) accompanied by 66% fluorescence quenching. However, the presence of target ssDNA will hybridize with the probe. The resultant helix cannot be adsorbed by CPNB due to its rigid conformation and the absence of unpaired DNA bases. Thus, a significant fluorescence enhancement, 73% fluorescence recovery, was observed in DNA detection as long as the target exists. The present system has excellent sensitivity; a substantial fluorescence enhancement was observed when the concentration of the target was as low as 5 nM. It also exhibits outstanding discrimination ability down to a single-base mismatch.     

Nano-C(60) : a novel, effective, fluorescent sensing platform for biomolecular detection

Water-soluble nano-C(60) can serve as a novel, effective, fluorescent sensing platform for biomolecular detection with high sensitivity and selectivity. In this paper, fluorescent detection of DNA and thrombin via nano-C(60) is demonstrated for the first time. The principle of the assay lies in the fact that the adsorption of the fluorescently labeled single-stranded DNA (ssDNA) probe by nano-C(60) leads to substantial fluorescence quenching. In the presence of a target, the biomolecular mutual interaction suppresses this quenching, signaling the existence of the target. This sensing system rivals graphene oxide but is superior to other carbon-structure-based systems. The present method can also achieve multiplex DNA detection and withstand the interference from human blood serum.     

2,4,6-Tris (2-pyridyl)-1,3,5-triazine nanobelts as an effective fluorescent sensing platform for DNA detection

In the present study, we report on the use of 2,4,6-tris (2-pyridyl)-1,3,5-triazine nanobelts (TPTNBs) as an effective fluorescent sensing platform for DNA detection for the first time. The general concept used in this approach is based on adsorption of fluorescently labeled single-stranded DNA (ssDNA) probe by TPTNB, due to the strong pi-pi stacking between unpaired DNA bases and TPTNB. As a result, the fluorophor is brought into close proximity of TPTNB, leading to fluorescence quenching. Upon presence of the target ssDNA, specific hybridization with the target takes place to form a double-stranded DNA (dsDNA). The resultant dsDNA cannot be adsorbed by TPTNB due to its rigid conformation and the absence of unpaired DNA bases. Thus, the fluorophor is seperated from TPTNB accompanied by fluorescence recovery. The present system shows a detection limit as low as 3 nM and has a high selectivity down to single-base mismatch.     

Fluorescence recovery assay for the detection of protein-DNA binding

We report a novel and straightforward fluorescence recovery assay which enables the detection of protein-DNA interactions and simultaneously determines relative binding affinities of sequence-specific DNA-binding proteins for a variety of DNA sequences in a multiplexed format. The detection of protein-DNA binding is accomplished by monitoring fluorescence recovery during exonuclease digestion of DNA sequences that are modified with fluorophore-quencher pairs. Retardation of fluorescence recovery occurs with binding of the protein to the putative DNA binding element, which arrests exonuclease digestion. The assay detects protein-DNA binding in a homogeneous solution simply, quickly, and reliably without using radioisotopes. Multiplexing is possible by labeling different DNA sequences with spectrally distinct dyes, allowing simultaneous analysis of experimental and control binding reactions in the same mixture.     

Single nucleotide polymorphism analysis based on minisequencing coupled with a fluorescence microsphere technology

In this paper, we describe a new method for detection of single nucleotide polymorphisms (SNPs) by applying the minisequencing principle to a fluorescence microsphere format. The specific primer, which was designed to anneal to its target of genomic DNA fragment immediately upstream of the polymorphic site, was immobilized to carboxylated Luminex microspheres as a probe. The primer was hybridized with genomic DNA fragments containing polymorphic sites and extended one base in the presence of biotin labeled ddNTP and DNA polymerase. After the extension reaction, Streptavidin-phycoerythrin was added to a reaction mixture to combine the biotin labeled with ddNTP. The final reaction products were analyzed by a Luminex 100 instrument. The fluorescence intensity of the Streptavidin-phycoerythrin combined with the extended ddNTP-biotin was used to identify the SNPs. The results showed that this method is highly sensitive, specific, and suitable for quantitative SNP detection. There was a good linear relationship between the mutant allele frequencies and the relative fluorescence intensities produced by mutant and wild-type gene fragments. A mutant allele frequency as low as 1.0% was accurately determined.     

DNA detection using a triple readout optical/AFM/MALDI planar microwell plastic chip

A ready-to-spot disposable DNA chip for specific and sensitive detection of DNA was developed. Plastic copolymeric substrate chemistry was optimized to selectively couple the target DNA with the active chip surface. At the same time, the developed substrate limits the unspecific adsorption of probe DNA molecules or additional polar contaminants in the test samples to the chip surface. The combination of glycidyl and n-butyl methacrylates was found to best fit the requirements of the assay. The fabricated DNA microarrays have mechanical properties similar to those of the glass or silicon substrates and, at the same time, provide chemically reactive surfaces that do not require lengthy chemical modification. An additional advantage of the plastic microchip is its compatibility with different analytical readout techniques, such as mass spectrometry (MALDI-TOF/MS), optical detection (fluorescence and enzyme-induced metal deposition), and imaging techniques (atomic force microscopy). These multiple readout techniques have given us the ability to compare the sensitivity, selectivity, and robustness of current state-of-the-art bioanalytical methods on the same platform exemplified by successful DNA-based detection of human cytomegalovirus. The obtained sensitivity for enzymatically enhanced silver deposition (10(-15) M) surpasses that of conventional fluorescence readouts. In addition, the assay's dynamic range (10(-6)-10(-15) M), reproducibility, and reliability of the DNA probe detection speaks for the silver deposition method. At compromised sensitivity (10(-9) M), the length of the DNA probes could be checked and, alternatively, DNA single point polymorphisms could be analyzed.