Effect of rice-husk ash on durability of cementitious materials

In this paper the effects of partial replacements of Portland cement by rice-husk ash (RHA) on the durability of conventional and high performance cementitious materials are investigated. Different percentages of RHA replacement levels, two RHAs (amorphous and partially crystalline optimized by dry-milling) and several water–cementitious materials ratio are studied. The following durability aspects were tested: air permeability, chloride ion penetration, alkali-silica expansion, sulfate and acid resistance. The results were compared with those of cementitious materials without RHA. It is concluded from the tested properties that the incorporation of both RHAs in concretes show different behaviors for air permeability and chloride ion penetration depending on the water/cementitious materials ratio used; in mortars, it reduces the mass loss of specimens exposed to hydrochloric acid solution and decreases the expansion due to sulfate attack and the alkali-silica reaction. The results of durability aspects due to physical or pozzolanic effects after the addition of both RHAs, and its chemical composition, in general indicate an enhanced performance, proving the feasibility of its rational utilization as a supplementary cementing material.     

The combined benefits of CPF and RHA in improving the durability of concrete structures

The work presented is a laboratory study of controlled permeability formwork (CPF) applied to concrete where cement was partially replaced (10%, 15% and 20%) with Portuguese rice husk ash (RHA). Portuguese rice husk is a by-product which may be incinerated industrially. Various tests were carried out to evaluate the durability of concrete made with RHA at 10%, 15% and 20% replacement of cement by weight and cast with both the usual formwork and CPF. Tests carried out so far, reported in this paper, concern strength, absorption by capillarity and chloride ion penetration. Results lead to the conclusion that CPF enhances concrete performance even further when using partial cement replacement by RHA.     

Development of vegetable fibre–mortar composites of improved durability

The primary concern for vegetable fibre reinforced mortar composites (VFRMC) is the durability of the fibres in the alkaline environment of cement. The composites may undergo a reduction in strength and toughness as a result of weakening of the fibres by a combination of alkali attack and mineralisation through the migration of hydration products to lumens and spaces. This paper presents several approaches used to improve the durability performance of VFRMCs incorporating sisal and coconut fibres. These include carbonation of the matrix in a CO₂-rich environment; the immersion of fibres in slurried silica fume prior to incorporation in the ordinary Portland cement (OPC) matrix; partial replacement of OPC matrix by undensified silica fume or blast-furnace slag and a combination of fibre immersion in slurried silica fume and cement replacement. The durability of the modified VFRMC was studied by determining the effects of ageing in water, exposure to cycles of wetting and drying and open air weathering on the microstructures and flexural behaviour of the composites. Immersion of natural fibres in a silica fume slurry before their addition to cement-based composites was found to be an effective means of reducing embrittlement of the composite in the environments studied. Early cure of composites in a CO2-rich environment and the partial replacement of OPC by undensified silica fume were also efficient approaches in obtaining a composite of improved durability. The use of slag as a partial cement replacement had no effect on reducing the embrittlement of the composite.     

Use of ultrafine rice husk ash with high-carbon content as pozzolan in high performance concrete

Rice husk ash (RHA) has been generated in large quantities in rice producing countries. This by-product can contain non-crystalline silica and thus has a high potential to be used as cement replacement in mortar and concrete. However, as the RHA produced by uncontrolled burning conditions usually contains high-carbon content in its composition, the pozzolanic activity of the ash and the rheology of mortar or concrete can be adversely affected. In this paper the influence of different grinding times in a vibratory mill, operating in dry open-circuit, on the particle size distribution, BET specific surface area and pozzolanic activity of the RHA is studied, in order to improve RHA’s performance. In addition, four high-performance concretes were produced with 0%, 10%, 15%, and 20% of the cement (by mass) replaced by ultrafine RHA. For these mixtures, rheological, mechanical and durability tests were performed. For all levels of cement replacement, especially for the 20%, the ultra-fine RHA concretes achieved superior performance in the mechanical and durability tests compared with the reference mixture. The workability of the concrete, however, was reduced with the increase of cement replacement by RHA.     

Effect of utilizing unground and ground normal and black rice husk ash on the mechanical and durability properties of high-strength concrete

The aim of the present study is to investigate the effects of utilizing different processings of normal rice husk ash (RHA) and black rice husk ash (BRHA) on the mechanical and durability properties of high-strength concrete (HSC). Mechanical and durability properties of HSC were evaluated on concrete mixes containing unground BRHA and RHA and ground BRHA and RHA, their average particles sizes being 165, 85, 67 and 24 µm, respectively. The replacement of ordinary Portland cement with the ashes was adopted at 20%. The results showed that incorporating any form of RHA and BRHA in HSC reduced the slump value. The surface areas of RHA and BRHA, not their carbon content, determined the dosage of superplasticizer needed to achieve a targeted slump value. Concrete with unground and ground RHA incorporated exhibited 30% higher compressive strength while unground BRHA produced 30% lower compressive strength than that of the control concrete. Incorporating unground and ground RHA showed a synergy between filler and pozzolanic effect and had insignificant difference in mechanical and durability properties of the concretes. Meanwhile, incorporating ground BRHA showed a dominant filler effect in the concrete. Overall, the improvement of splitting tensile strength and modulus of elasticity of both RHA and GBRHA concrete showed a similar trend to that of the compressive strength of RHA concrete. The durability of concretes with unground and ground RHA and ground BRHA incorporated showed better performance than that of the control concrete. The material with 20% ground BRHA as partial cement replacement in HSC of Grade 50 could be used without any reduction in the mechanical and durability properties. Use of unground BRHA is not recommended because it did not improve these properties.     

Freeze–thaw resistance and transport properties of high-volume fly ash roller compacted concrete designed by maximum density method

The aim of this study is to evaluate the effect of high-volume fly ash on some durability characteristics of roller compacted concrete (RCC). In addition to a control mixture without fly ash, two different series of mixtures were prepared by partial replacement of either cement or aggregate with fly ash. The mixtures were designed by a maximum density method. A total of 28 mixtures having four different water/binder ratios (0.30, 0.35, 0.40 and 0.45 by mass) were prepared to determine the optimum water/binder ratio. Among these, seven mixtures containing the optimum water content were selected for further experimental study. It was observed that in the mixtures where cement was substituted with fly ash, increasing the fly ash content adversely affected the durability performance up to 90 days. However, fly ash substitution for a part of the aggregate improved the durability characteristics of the mixture as the amount of fly ash increased.     

Influence of a fine glass powder on the durability characteristics of concrete and its comparison to fly ash

A detailed investigation carried out to ascertain the durability characteristics of fine glass powder modified concretes is reported in this paper. Tests were designed to facilitate comparisons between concretes modified with either glass powder or fly ash at the same cement replacement level. The optimal replacement level of cement by glass powder is determined from strength and hydration tests as 10%. The later age compressive strengths of glass powder and fly ash modified concretes are seen to differ by only 5%. The durability characteristics are ascertained using tests for rapid chloride permeability, alkali–silica reactivity, and moisture transport parameters. The chloride penetrability values indicate some amount of pore refinement. The potential of glass powder to reduce the expansion due to alkali–silica reaction is established from tests conducted in accordance with ASTM C 1260, but fly ash is found to perform better at similar replacement levels. Glass powder–fly ash blends that make up a 20% cement replacement level are found to be as efficient as 20% fly ash in reducing expansion. The control concrete is seen to exhibit the lowest overall moisture intake after 14 days of curing, and fly ash concrete the highest, with the glass powder concrete in between. The trend is reversed at later ages, demonstrating that both the replacement materials contribute to improved durability characteristics. The sorptivity and moisture diffusion coefficient values calculated from the moisture intake-time data also demonstrate a similar trend. These studies show that fine glass powder has the potential to improve the durability of concretes.     

Use of rice husk ash in sandcrete blocks for masonry units

Different mix proportions of sand, cement and rice husk ash (RHA) were studied for use in sandcrete blocks. Optimum water/(cement+RHA) ratios were determined at different mix proportions. Compressive strengths of various mix proportions at 7, 28 and 60 days were also determined. The optimum water/(cement+RHA) ratio increased with rice husk ash contents. Test results showed that up to 40% RHA could be added as a partial replacement for cement without any significant change in compressive strength at 60 days. Compressive strengths of various mix proportions were compared with British Statutory minimum compressive strengths of bricks for various walls and it was found that sandcrete blocks of 1∶5 mortar mixes with 40% RHA (by weight of cement) could be used in both load and non-load bearing walls.     

Assessing the effect of biomass ashes with different finenesses on the compressive strength of blended cement paste

This study assesses the effect of biomass ashes with different finenesses on the compressive strength of blended cement paste. rice husk ash (RHA), palm oil fuel ash (POFA) and river sand (RS) were ground to obtain two finenesses: one was the same size as the cement, and the other was smaller than the cement. Type I Portland cement was replaced by RHA, POFA and RS at 0%, 10%, 20%, 30% and 40% by weight of binder. A water to binder ratio (W/B) of 0.35 was used for all blended cement paste mixes. The percentages of amorphous materials and the compressive strength of the pastes due to the hydration reaction, filler effect and pozzolanic reaction were investigated. The results showed that ground rice husk ash and ground palm oil fuel ash were composed of amorphous silica material. The compressive strength of the pastes due to the hydration reaction decreased with decreasing cement content. The compressive strength of the pastes due to the filler effect increased with increasing cement replacement. The compressive strengths of the pastes due to the pozzolanic reaction were nonlinear and were fit with nonlinear isotherms that increased with increasing fineness of RHA and POFA, cement replacement rate and age of the paste. In addition, the model that was proposed to predict the percentage compressive strength of the blended cement pastes on the basis of the age of the paste and the percentage replacement with biomass ash was in good agreement with the experimental results. The optimum replacement level of rice husk ash and palm oil fuel ash in pastes was 30% by weight of binder; this replacement percentage resulted in good compressive strengths.     

Performance and properties of mortar mixed with nano-CuO and rice husk ash

This paper presents an experimental study on a new mixture scheme of mortar. Unlike most of existing work, the present study investigates nano-CuO (NC), and its combined effects with cement replacement i.e., rice husk ash (RHA) on durability performance, as well as strength and permeability properties of mortars. Comprehensive observations of both the performance and properties improvements on RHA-containing mortar specimens were determined with the addition of NC. To this end, a series of tests for examining the strength both directly (compressive strength) and indirectly (Ultrasonic Pulse Velocity), electrical resistivity, chloride permeability, water absorption and microstructure characteristics (i.e., SEM micrographs, Mercury intrusion porosimetry (MIP) & capillary analyses) of mortar specimens were performed. A relationship between the Rapid chloride permeability test (RCPT) and electrical resistivity was also studied in order to recommend an alternative method for quality control in the presence of RHA and NC. Finally, a mixture scheme which provides relatively satisfactory properties improvement with positive environment credential is suggested.     

Hydration of high-volume fly ash cement pastes

The hydration processes of high-volume fly ash cement paste were investigated by examining the non-evaporable water content, the CH content, the pH of pore solution and the fraction of reacted fly ash, curing at either 20°C or elevated temperatures after an initial curing at 20°C. The replacement percentage levels of fly ash were 40%, 50% and 60% by weight, respectively. The results revealed that the non-evaporable water content in high-volume fly ash cement pastes does not develop as plain cement pastes does, so it may be improper to apply the non-evaporable water content to evaluate the hydration process in high-volume fly ash cement matrix. The reduction in CH content increases with the progressing of hydration process and varies linearly with the logarithm of curing age. The addition of 3.0% of Na₂SO₄ could accelerate the pozzolanic reaction of fly ash at early ages. At 20°C, the pH of pore solution of high-volume fly ash cement paste was reduced to a great extent at early ages and it continued to decline at later ages due to the inclusion of large amount of fly ashes. At elevated temperatures, however, this trend was not found. The fraction of reacted fly ash directly reflects the pozzolanic reactivity of fly ash both at normal and elevated temperatures. There is some inherent correlation between the reduction in CH content, the pH of pore solution and the fraction of reacted fly ash. For specified matrix, the consumption of CH and the pH of pore solutions change linearly with the increase of the fraction of reacted fly ash.     

Decoupling the physical and chemical effects of supplementary cementitious materials on strength and permeability: A multi-level approach

Supplementary cementitious materials (SCMs) represent an alternative for the industry to achieve sustainability by reducing cement contents without significant compromises of the mechanical properties and enhancing durability. SCMs play a dual role during hydration: a physical effect promoting nucleation and cement hydration and a chemical effect through pozzolanic activity. Rice husk ash (RHA) and natural pozzolans (NP) were evaluated using compressive strength and durability tests in a multi-level experimental program. RHA increased the strength more than NP, which is well explained by its prominent chemical effect (78%) assessed by isothermal calorimetry and its high amorphous silica content. Both RHA and NP produced significant reductions in the permeability of the concrete, which is mostly explained by the chemical effect. Decoupling the physical and chemical effects of a SCM allows for optimisation of its manufacturing process.     

Effect of grinding of low-carbon rice husk ash on the microstructure and performance properties of blended cement concrete

The effectiveness of unground low-carbon rice husk ash (URHA) as a pozzolan and the effect of grinding the URHA to finer fractions for use in portland cement system were investigated. The properties investigated include the setting time and calcium hydroxide depletion of rice husk ash (RHA) pastes; microstructure and flow behavior of RHA mortars; strength and durability of RHA concretes. Results from this investigation suggested that the URHA and ground RHA (GRHA) mixtures performed better than the control mixtures in all tests conducted except water demand and setting time. The URHA mixture revealed denser microstructure compared to the control mixture. The internal porosity created by the coarse RHA grains in the matrix and their inability to completely participate in pozzolanic reaction may be the reasons for the poorer performance of the URHA mixture than compared to the GRHA mixture. The effect of grinding the RHA to finer fractions either substantially or slightly improved all properties except final setting time. With the performance of the GRHA concrete somewhat similar to that of the SF concrete, the use of ground RHA can be concluded to provide acceptable performance in portland cement systems.     

Transport properties of self compacting concrete with limestone filler or fly ash

The durability of a cementitious material is greatly influenced by the permeability of the material for potentially aggressive substances. As the pore structure of self compacting concrete (SCC) might be different in comparison with traditional concrete (TC), some changes in durability behaviour may occur. At this moment however, it is unclear how significant these differences will be with regard to the concrete practice. In this paper, the gas and water transport in SCC with limestone filler or fly ash is investigated experimentally. Nine different concrete compositions are considered: one TC and eight SCC mixtures. Some important parameters like the water/cement (W/C) and cement/powder ratio (C/P), type of filler (limestone filler and fly ash), type of aggregate and type of cement are considered. The results of the gas and water transport are discussed and linked to experimental data concerning pore volume. Lower transport properties can be obtained by using fly ash instead of limestone as filler material, by lowering the W/C ratio, decreasing the C/P ratio at a constant W/C ratio or using blast furnace slag cement instead of portland cement. The effect of changing from gravel to crushed limestone is small. SCC is differing strongly of TC with respect to the apparent gas permeability. This difference is probably due to the differences in pore volume, as seen from MIP results.     

Strength development of concrete with rice-husk ash

This paper presents a study on the development of compressive strength up to 91 days of concretes with rice-husk ash (RHA), in which residual RHA from a rice paddy milling industry in Uruguay and RHA produced by controlled incineration from the USA were used for comparison. Two different replacement percentages of cement by RHA, 10% and 20%, and three different water/cementicious material ratios (0.50, 0.40 and 0.32), were used. The results are compared with those of the concrete without RHA, with splitting tensile strength and air permeability. It is concluded that residual RHA provides a positive effect on the compressive strength at early ages, but the long term behavior of the concretes with RHA produced by controlled incineration was more significant. Results of splitting tensile and air permeability reveal the significance of the filler and pozzolanic effect for the concretes with residual RHA and RHA produced by controlled incineration.     

Water absorption control of ternary blended concrete with nano-SiO2 in presence of rice husk ash

In the current study, the effects of SiO₂ nanoparticles as additive with two different sizes of 15 and 80?nm on water absorption of rice husk ash (RHA) blended concrete have been investigated. Concrete samples were prepared by replacing 10, 15 and 20?wt% of cement with RHA and 0.5, 1.0, 1.5 and 2.0% of cement with SiO₂ nanoparticles followed by curing in lime solution for 7, 28 and 90?days. The results indicated that the resistance to water absorption of Portland cement?Cnano SiO₂?Crice husk ash (PC?CNS?CRHA) ternary blended concrete was considerably improved with respect to the control concrete. This improvement was observed at all curing ages and replacement levels but the optimal point was reached for 20% of RHA incorporating 2% of 80?nm SiO₂ particles at 90?days of curing. Fast formation of C?CS?CH gel in the presence of ultra high active nano-sized SiO₂ and micron level RHA particles together with their high filler effect may result in a continuous cement paste with the lowest weak zones. It has been concluded that the use of novel ternary blended concrete (PC?CNS?CRHA) provides significant reduction in the water absorption of concrete.     

Evaluation of bagasse ash as supplementary cementitious material

The utilization of waste materials in concrete manufacture provides a satisfactory solution to some of the environmental concerns and problems associated with waste management. Agro wastes such as rice husk ash, wheat straw ash, hazel nutshell and sugarcane bagasse ash are used as pozzolanic materials for the development of blended cements. Few studies have been reported on the use of bagasse ash (BA) as partial cement replacement material in respect of cement mortars. In this study, the effects of BA content as partial replacement of cement on physical and mechanical properties of hardened concrete are reported. The properties of concrete investigated include compressive strength, splitting tensile strength, water absorption, permeability characteristics, chloride diffusion and resistance to chloride ion penetration. The test results indicate that BA is an effective mineral admixture, with 20% as optimal replacement ratio of cement.     

Effect of fly ash fineness on compressive strength and pore size of blended cement paste

This paper presents an experimental investigation on the effect of fly ash fineness on compressive strength, porosity, and pore size distribution of hardened cement pastes. Class F fly ash with two fineness, an original fly ash and a classified fly ash, with median particle size of 19.1 and 6.4 μm respectively were used to partially replace portland cement at 0%, 20%, and 40% by weight. The water to binder ratio (w/b) of 0.35 was used for all the blended cement paste mixes.Test results indicated that the blended cement paste with classified fly ash produced paste with higher compressive strength than that with original fly ash. The porosity and pore size of blended cement paste was significantly affected by the replacement of fly ash and its fineness. The replacement of portland cement by original fly ash increased the porosity but decreased the average pore size of the paste. The measured gel porosity (5.7–10 nm) increased with an increase in the fly ash content. The incorporation of classified fly ash decreased the porosity and average pore size of the paste as compared to that with ordinary fly ash. The total porosity and capillary pores decreased while the gel pore increased as a result of the addition of finer fly ash at all replacement levels.     

Optimization of concrete mixture with hybrid blends of metakaolin and fly ash using response surface method

This paper presents the experimental results of a research carried out on the strength and permeability related properties of high performance concretes made with binary and ternary cementitious blends of fly ash (FA) and metakaolin (MK). The replacement ratios for FA were 10% and 20% by weight of Portland cement and those for MK were 5% and 10%. Compressive strength, chloride permeability, water sorptivity, and water absorption properties of concretes were obtained in this study for different testing ages up to 90 days. The influences of fly ash, metakaolin, and testing age on the properties of concretes have been identified using the analysis of variance. The statistical based regression models and the response surface method with the backward stepwise techniques were employed in the multi-objective optimization analysis. That is carried out by maximizing compressive strength while minimizing chloride permeability, water sorptivity, and water absorption. It was observed that fly ash and especially metakaolin were very effective on the aforementioned properties of the concretes, depending mainly on replacement levels and duration of curing. The results indicated that the ternary use of fly ash and metakaolin with the approximate cement replacement values of 13.3% and 10% respectively has provided the best results for the testing age of 90 days, when the optimized strength and permeability based durability properties of the concretes are concerned.     

Compressive strength and durability properties of ceramic wastes based concrete

This paper presents an experimental study on the properties and on the durability of concrete containing ceramic wastes. Several concrete mixes possessing a target mean compressive strength of 30 MPa were prepared with 20% cement replacement by ceramic powder (W/B = 0.6). A concrete mix with ceramic sand and granite aggregates were also prepared as well as a concrete mix with natural sand and coarse ceramic aggregates (W/B = 0.5). The mechanical and durability performance of ceramic waste based concrete are assessed by means of mechanical tests, water performance, permeability, chloride diffusion and also accelerated aging tests. Results show that concrete with partial cement replacement by ceramic powder although it has minor strength loss possess increase durability performance. Results also shows that concrete mixtures with ceramic aggregates perform better than the control concrete mixtures concerning compressive strength, capillarity water absorption, oxygen permeability and chloride diffusion. The replacement of cement and aggregates in concrete by ceramic wastes will have major environmental benefits.