Effects of CaSiO3 addition on sintering behavior and microwave dielectric properties of Al2O3 ceramics

The effects of CaSiO₃ addition on the sintering behavior and microwave dielectric properties of Al₂O₃ ceramics have been investigated. The addition of CaSiO₃ into Al₂O₃ ceramics resulted in the emergence of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which acting as liquid sintering aids can effectively lower the sintering temperature of Al₂O₃ ceramic. The Q × f value of Al₂O₃-CaSiO₃ ceramics decreased with the CaSiO₃ addition increasing because of the lower Q × f value of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈. Compared with the pure CaSiO₃ ceramic, the Al₂O₃-CaSiO₃ ceramic with 20 wt% CaSiO₃ addition possessed good dielectric properties of ?_r = 9.36 and Q × f = 13,678 GHz at the similar sintering temperature.     

Microwave dielectric properties of SnO2-doped CaSiO3 ceramics

SnO₂-doped CaSiO₃ ceramics were successfully synthesized by a solid-state method. Effects of different SnO₂ additions on the sintering behavior, microstructure and dielectric properties of Ca(Sn_1−xSi_x)O₃ (x=0.5–1.0) ceramics have been investigated. SnO₂ improved the densification process and expanded the sintering temperature range effectively. Moreover, Sn⁴⁺ substituting for Si⁴⁺ sites leads to the emergence of Ca₃SnSi₂O₉ phase, which has a positive effect on the dielectric properties of CaO–SiO₂–SnO₂ materials, especially the Qf value. The Ca(Sn_0.1Si_0.9)O₃ ceramics sintered at 1375 °C possessed good microwave dielectric properties: ε_r =7.92, Qf =58,000 GHz and τ_f=−42 ppm/°C. The Ca(Sn_0.4Si_0.6)O₃ ceramics sintered at 1450 °C also exhibited good microwave dielectric properties of ε_r=9.27, Qf=63,000 GHz, and τ_f=−52 ppm/°C. Thus, they are promising candidate materials for millimeter-wave devices.     

Low temperature sintering and microwave dielectric properties of CaSiO3–Al2O3 ceramics for LTCC applications

The effects of CuO, Li₂CO₃ and CaTiO₃ additives on the densification, microstructure and microwave dielectric properties of CaSiO₃–1 wt% Al₂O₃ ceramics for low-temperature co-fired applications were investigated. With a single addition of 1 wt% Li₂CO₃, the CaSiO₃–1 wt% Al₂O₃ ceramic required a temperature of at least 975 °C to be dense enough. Large amount addition of Li₂CO₃ into the CaSiO₃–1 wt% Al₂O₃ ceramics led to the visible presence of Li₂Ca₃Si₆O₁₆ and Li₂Ca₄Si₄O₁₃ second phases. Fixing the Li₂CO₃ content at 1 wt%, a small amount of CuO addition significantly promoted the sintering process and lowered the densification temperature to 900 °C whereas its addition deteriorated the microwave dielectric properties of CaSiO₃–1 wt% Al₂O₃ ceramics. Based on 10 wt% CaTiO₃ compensation in temperature coefficient, good microwave dielectric properties of ε_r=8.92, Q×f=19,763 GHz and τ_f=−1.22 ppm/°C could be obtained for the 0.2 wt% CuO and 1.5 wt% Li₂CO₃ doped CaSiO₃–1 wt% Al₂O₃ ceramics sintered at 900 °C. The chemical compatibility of the above ceramics with silver during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between silver and ceramics, indicating that the as-prepared composite ceramics were suitable for low-temperature co-fired ceramics applications.     

Sintering behavior and microwave dielectric properties of a new low-permittivity ceramic system Ca(Mg1−xAlx)(Si1−x/2Alx/2)2O6

The diopside ceramics with a formula of Ca(Mg_1−xAl_x)(Si_1−x/2Al_x/2)₂O₆ (x=0.01–0.3) were synthesized via a traditional solid-state reaction method, and their solid solubility, sintering behavior and microwave dielectric properties were investigated. The results revealed that the solubility limit of Al₂O₃ in Ca(Mg_1−xAl_x)(Si_1−x/2Al_x/2)₂O₆, which is defined as x, was between 0.15 and 0.2, and a second phase of CaAl₂SiO₆ presented when the x value reached 0.2. Appropriate Al³⁺ substitution for Mg²⁺ and Si⁴⁺ could promote the sintering process and lower the densification temperature, and a broadened densification temperature range of 1250–1300 °C was obtained for the compositions of x=0.08–0.15. With the increase of the x value, the dielectric constant (ε_r) increased roughly linearly, and the temperature coefficient of frequency (τ_f) showed a rising trend. The Q×f values increased from 57,322 GHz to 59,772 GHz as the x value increased from 0.01 to 0.08, and then they were saturated in the range of x=0.08–0.2. Further increase of the x value (x≥0.25) deteriorated the microwave dielectric properties. Good microwave dielectric properties of ε_r=7.89, Q×f=59,772 GHz and τ_f=−42.12 ppm/°C were obtained for the ceramics with the composition of x=0.08 sintered at 1275 °C.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Dielectric properties and microstructures of CaSiO3 ceramics with B2O3 addition

The effects of B₂O₃ additives on the sintering behavior, microstructure and dielectric properties of CaSiO₃ ceramics have been investigated. The B₂O₃ addition resulted in the emergence of CaO–B₂O₃–SiO₂ glass phase, which was advantageous to lower the synthesis temperature of CaSiO₃ crystal phase, and could effectively lower the densification temperature of CaSiO₃ ceramic to as low as 1100 °C. The 6 wt% B₂O₃-doped CaSiO₃ ceramic sintered at 1100 °C possessed good dielectric properties: _r = 6.84 and tan δ = 6.9 × 10⁻⁴ (1 MHz).     

Preparation and microwave dielectric properties of 3ZnO·B2O3 ceramics with low sintering temperature

The preparation and dielectric properties of 3ZnO·B₂O₃ ceramics were investigated. Dense 3ZnO·B₂O₃ ceramics were obtained as sintered in the temperature range from 950 to 1000 °C for 3 h. The X-ray diffraction showed that the obtained ceramics were of a monoclinic 3ZnO·B₂O₃ structure. The ceramic specimens fired at 955 °C for 1 h exhibited excellent microwave dielectric properties: ?_r ∼ 6.9, Q × f ∼ 20,647 GHz (@6.35 GHz), and τ_f ∼ −80 ppm/°C. The dependences of relative density, ?_r, and Q × f of ceramics sintered at 955 °C on sintering soaking time showed that they all reached their plateaus as the soaking time was up to 60 min. Meanwhile, 3ZnO·B₂O₃ ceramics had no reaction with silver during cofiring, indicating it is a potential candidate for low-temperature cofired ceramic (LTCC) substrate.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Synthesis of Zn3Nb2O8 ceramics using a simple and effective process

Synthesis of Zn₃Nb₂O₈ ceramics using a simple and effective reaction-sintering process was investigated. The mixture of ZnO and Nb₂O₅ was pressed and sintered directly without any prior calcination. Single-phase Zn₃Nb₂O₈ ceramics could be obtained. Density of these ceramics increased with soaking time and sintering temperature. A maximum density 5.72 g/cm³ (99.7% of the theoretical density) was found for pellets sintered at 1170 °C for 2 h. Pores were not found and grain sizes >20 μm were observed in pellets sintered at 1170 °C. Abnormal grain growth occurred and grains >50 μm could be seen in Zn₃Nb₂O₈ ceramics sintered at 1200 °C for 2 h and 1200 °C for 4 h. Reaction-sintering process is then a simple and effective method to produce Zn₃Nb₂O₈ ceramics for applications in microwave dielectric resonators.     

Densification, microstructural evolution and microwave dielectric properties of fluxed sintered 12R-Ba(Ti0.5Mn0.5)O3 ceramics

Doped hexagonal BaTiO₃ (h-BaTiO₃) ceramics have recently been identified as potential candidates for use in microwave dielectric resonators. However, similar to other common microwave ceramics, doped h-BaTiO₃ ceramics require a sintering temperature higher than 1400 °C. In this study, the effects of Bi₂O₃ and Li₂CO₃ on the densification, microstructural evolution and microwave properties of hexagonal 12R-Ba(Ti_0.5Mn_0.5)O₃ ceramics were examined. Results indicate that Bi₂O₃ and Li₂CO₃ are able to effectively reduce the sintering temperature of 12R-Ba(Ti₀₅Mn_0.5)O₃ ceramics through liquid phase sintering while retaining the hexagonal structure and the microwave dielectric properties. The best results were obtained for the 12R-Ba(Ti_0.5Mn_0.5)O₃ with the additions of 5 wt% Bi₂O₃ sintered at 1200 °C (?_r: 36.0, Qf_r: 6779 GHz, and τ_f: 25.3 ppm/°C), and 5 wt% Li₂CO₃ sintered at 1200 °C (?_r: 28.1, Qf_r: 5304 GHz, and τ_f: 35.3 ppm/°C).     

Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

Transparent polycrystalline MgAl2O4 ceramic fabricated by spark plasma sintering: Microwave dielectric and optical properties

The optical properties and microwave dielectric properties of transparent polycrystalline MgAl₂O₄ ceramics sintered by spark plasma sintering (SPS) through homemade nanosized MgAl₂O₄ powders at temperatures between 1250 °C and 1375 °C are discussed. The results indicate that, with increasing sintering temperatures, grain growth and densification occurred up to 1275 °C, and above 1350 °C, rapid grain and pore growth occurred. The in-line light transmission increases with the densification and decreases with the grain/pore growth, which can be as high as 70% at the wavelength of 550 nm and 82% at the wavelength of 2000 nm, respectively. As the sintering temperature increases, Q×f and dielectric constant ε_r values increase to maximum and then decrease respectively, while τ_f value is almost independent of the sintering temperatures and remains between −77 and −71 ppm/°C. The optimal microwave dielectric properties (ε_r=8.38, Q×f=54,000 GHz and τ_f=−74 ppm/°C) are achieved for transparent MgAl₂O₄ ceramics produced by spark plasma sintering at 1325 °C for 20 min.     

Synthesis and microwave dielectric properties of CaSiO3 nanopowder by the sol–gel process

The synthesis and microwave dielectric properties of CaSiO₃ nanopowder by sol–gel method have been investigated in this paper. CaSiO₃ nanoparticles with an average grain size of 50–60 nm were obtained by calcining the CaO–SiO₂ xerogel that was prepared from Calcium nitrate tetrahydrate (Ca(NO₃)₂·4H₂O) and tetraethylortho silicate (TEOS). Calcining the CaO–SiO₂ xerogel at 1150 °C, the pseudowollastonite-CaSiO₃ phase was completely formed. However, the main phase is not CaSiO₃ or CaSi₂O₄ but SiO₂ when calcining the mixture of SiO₂ and CaCO₃ at 1150 °C. Comparing with CaO–SiO₂ ceramics prepared by solid-state process, the CaSiO₃ ceramics made from nanopowders calcined at 1000 °C achieved more compact structure at the sintering temperature of 1320 °C, and then had excellent microwave dielectric properties: ?_r = 6.69, Qf = 25398 GHz.     

Effects of CaTiO3 addition on the densification and microwave dielectric properties of BiSbO4 ceramics

In this study, the effects of CaTiO₃ addition on the sintering characteristics and microwave dielectric properties of BiSbO₄ were investigated. Pure BiSbO₄ achieved a sintered density of 8.46 g/cm³ at 1100 °C. The value of sintered density decreased with increasing CaTiO₃, and sintering at a temperature higher than 1100 °C led to a large weight loss (>2 wt%) caused by the volatile nature of the compound. Samples either sintered above 1100 °C or with a CaTiO₃ content exceeding 3 wt% showed poor densification. SEM micrographs revealed microstructures with bimodal grain size distribution. The size of the smaller grains ranged from 0.5 to 1.2 μm and that of the larger grains between 3 and 7 μm. The microwave dielectric properties of the (1−x) BiSbO_4−x CaTiO₃ ceramics are dependent both on the x value and on the sintering temperature. The 99.0 wt% BiSbO₄–1.0 wt% CaTiO₃ ceramic sintered at 1100 °C reported overall microwave dielectric properties that can be summarized as ε_r≈21.8, Q×f≈61,150 GHz, and τ_f≈−40.1 ppm/°C, all superior to those of the BiSbO₄ ceramics sintered with other additives.     

TEM observation of liquid phase sintering in V2O5 modified Zr0.8Sn0.2TiO4 microwave ceramics

The phenomena of liquid phase sintering in the V₂O₅ modified (Zr_0.8, Sn_0.2)TiO₄ (ZST) microwave ceramics has been investigated by using transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDS). The amounts of second phase were too low to be detected by X-ray diffraction (XRD), but could be observed by TEM bright field image. However, the presence of grain boundary phases did not degrade the microwave properties of V₂O₅ modified ZST ceramics. The ?_r value of 37.2, Q × f value of 51,000 (at 7 GHz) and τ_f value of −2.1 ppm/°C were obtained for ZST ceramics with 1 wt% V₂O₅ addition sintered at 1300 °C.     

Influence of A-site Ba substitution on microwave dielectric properties of (BaxMg1−x)(A0.05Ti0.95)O3 (A=Zr,Sn) ceramics

The microwave dielectric properties of (Ba_xMg_1−x)(A_0.05Ti_0.95)TiO₃ (A=Zr, Sn) ceramics were investigated with regard to substitution of Ba for Mg of A-site. The microwave dielectric properties were correlated with the Ba content. With an increase in Ba content from 0.01 to 0.1, the dielectric constant and the τ_f value increased, but the Q×f value decreased. The sintered (Ba_xMg_1−x)(Zr_0.05Ti_0.95)TiO₃ (called B_xMZT) ceramics had a permittivity in the range of 19.1−20.6, quality factor from 180,000 to 25,000 GHz, and variation in temperature coefficient of resonant frequency from −35 to −39 ppm/°C with increasing composition x. For sintered (Ba_xMg_1−x)(Sn_0.05Ti_0.95)TiO₃ (called B_xMST) ceramics, the dielectric constant increased from 19 to 20.5, Q×f value increased from 120,000 to 37,000 (GHz), and the τ_f value increased from −50 to −3.3 ppm/°C as the x increased from 0.01 to 0.1. When A=Sn and x=0.1, (Ba_0.1Mg_0.9)(Sn_0.05Ti_0.95)TiO₃ ceramics exhibited dielectric constant of 20.5, Q×f value of 37,000 (GHz), and a near-zero τ_f value of −3.3 ppm/°C sintered at 1210 °C for 4 h.     

Effects of grinding and firing conditions on CaAl2Si2O8 phase formation by solid-state reaction of kaolinite with CaCO3

The effects of grinding and firing conditions on CaAl₂Si₂O₈ phase formation by solid-state reaction of kaolinite with CaCO₃ were investigated by differential thermal analysis (DTA)–thermogravimetry (TG), X-ray powder diffraction (XRD) and ²⁹Si and ²⁷Al MAS NMR. Unground and ground samples showed similar crystallization behavior at about 850 °C, and the crystallizing temperature was relatively unaffected by grinding. On the other hand, the crystalline products were strongly influenced by the grinding. Gehlenite (Ca₂Al₂SiO₇) was the dominant phase in the unground samples but layer-structured CaAl₂Si₂O₈ was dominant in the ground samples, together with a small amount of anorthite, which is the stable phase. The amount of anorthite gradually increased with higher firing temperature, the sample fired at 1000 °C being almost completely anorthite. Grinding treatment before firing was effective in accelerating the decomposition of CaCO₃ and extending the temperature range for the formation of CaAl₂Si₂O₈, a phase with local structure similar to that of layered CaAl₂Si₂O₈.     

Low temperature sintering and microwave dielectric properties of Li2ZnTi3O8 ceramics doped with ZnO–La2O3–B2O3 glass

Li₂ZnTi₃O₈ ceramics doped with ZnO–La₂O₃–B₂O₃ glass were prepared by the conventional solid-state ceramic route. The effects of the ZnO–La₂O₃–B₂O₃ glass on the sintering temperature, phase composition, microstructure and microwave dielectric properties of Li₂ZnTi₃O₈ ceramics were investigated. The addition of ZLB glass can reduce the sintering temperature of Li₂ZnTi₃O₈ ceramic from 1075 °C to 925 °C without obvious degradation of the microwave dielectric properties. Only a single phase Li₂ZnTi₃O₈ with cubic spinel structure is formed in Li₂ZnTi₃O₈ ceramic with ZLB addition sintered at 925 °C. Typically, 1.0 wt% ZLB-doped Li₂ZnTi₃O₈ ceramic sintered at 925 °C can reach a maximum relative density of 95.8% and exhibits good microwave dielectric properties of ε_r=24.34, Q×f=41,360 GHz and τ_f=−13.4 ppm/°C. Moreover, this material is compatible with Ag electrode, which makes it a promising candidate for LTCC application.     

Effects of Al2O3 addition on the microstructure and microwave dielectric properties of Ba4Nd9.33Ti18O54 ceramics

Ba₄Nd_9.33Ti₁₈O₅₄·x wt%Al₂O₃ (BNT-A) ceramics (x=0, 0.5, 1.0, 1.5, 2.0, 2.5) were prepared by the conventional solid state reaction. The effects of Al₂O₃ on the microstructure and microwave dielectric properties of Ba₄Nd_9.33Ti₁₈O₅₄ (BNT) ceramics were investigated. X-ray diffraction and backscatter electronic images showed that the Al₂O₃ additive gave rise to a second phase BaAl₂Ti₅O₁₄ (BAT). The formation mechanism and grain growth of the BAT phase were first discussed. Dielectric property test revealed that the Al₂O₃ additive had improved the dielectric properties of the BNT ceramics: increased the Q×f value from 8270 to 12,180 GHz and decreased the τ_f value from 53.4 to 11.2 ppm/°C. A BNT-A ceramic with excellent dielectric properties: ε_r=70.2, Q×f=12,180 GHz, τ_f=20 ppm/°C was obtained with 2.0 wt% Al₂O₃ added after sintering at 1320 °C for 4 h.     

Dielectric and mechanical properties of porous Si3N4 ceramics prepared via low temperature sintering

Borophosphosilicate bonded porous silicon nitride (Si₃N₄) ceramics were fabricated in air using a conventional ceramic process. The porous Si₃N₄ ceramics sintered at 1000–1200 °C shows a relatively high flexural strength and good dielectric properties. The influence of the sintering temperature and contents of additives on the flexural strength and dielectric properties of porous Si₃N₄ ceramics were investigated. Porous Si₃N₄ ceramics with a porosity of 30–55%, flexural strength of 40–130 MPa, as well as low dielectric constant of 3.5–4.6 were obtained.