Effect of CeO2 addition on densification and microstructure of Al2O3-YSZ composites

Alumina (Al₂O₃) and alumina-yttria stabilized zirconia (YSZ) composites containing 3 and 5 mass% ceria (CeO₂) were prepared by spark plasma sintering (SPS) at temperatures of 1350-1400 °C for 300 s under a pressure of 40 MPa. Densification, microstructure and mechanical properties of the Al₂O₃ based composites were investigated. Fully dense composites with a relative density of approximately 99% were obtained. The grain growth of alumina was inhibited significantly by the addition of 10 vol% zirconia, and formation of elongated CeAl₁₁O₁₈ grains was observed in the ceria containing composites sintered at 1400 °C. Al₂O₃-YSZ composites without CeO₂ had higher hardness than monolithic Al₂O₃ sintered body and the hardness of Al₂O₃-YSZ composites decreased from 20.3 GPa to 18.5 GPa when the content of ZrO₂ increased from 10 to 30 vol%. The fracture toughness of Al₂O₃ increased from 2.8 MPa m^1/2 to 5.6 MPa m^1/2 with the addition of 10 vol% YSZ, and further addition resulted in higher fracture toughness values. The highest value of fracture toughness, 6.2 MPa m^1/2, was achieved with the addition of 30 vol% YSZ.     

Spark plasma sintering technique for reaction sintering of Al2O3/Ni nanocomposite and its mechanical properties

Al₂O₃/Ni nanocomposites were prepared by spark plasma sintering (SPS) using reaction sintering method and the mechanical properties of the obtained nanocomposites are reported. The starting materials of Al₂O₃–NiO solid solution were synthesized from aluminum sulfate and nickel sulfate. These Al₂O₃–NiO powders were changed into Al₂O₃ and Ni phases during sintering process. The obtained nanocomposites showed high relative densities (>98%). SEM micrographs showed homogeneously dispersed Ni grains in the matrix. The 3-point strength and the fracture toughness of the composites significantly improved from 450 MPa in the monolithic α-Al₂O₃ to 766 MPa in the 10 mol% (2.8 vol.%) Ni nanocomposite and from 3.7 to 5.6 MPa m^1/2 in 13 mol% (3.7 vol.%) Ni nanocomposite. On the other hand, Young's modulus and Vickers hardness of the nanocomposites were mostly same as those of the monolithic α-Al₂O₃.     

Microstructure and mechanical properties of Al2O3/Er3Al5O12 eutectic rods grown by the laser-heated floating zone method

Eutectic rods of Al₂O₃-Er₃Al₅O₁₂ were grown by directional solidification using the laser-heated floating zone method at rates in the range 25-1500 mm/h. Their microstructure and mechanical properties (hardness, toughness and strength) were investigated as a function of the growth rate. A homogeneous and interpenetrated microstructure was found in most cases, and interphase spacing decreased with growth rate following the Hunt-Jackson law. Hardness increased slightly as the interphase spacing decreased while toughness was low and independent of the microstructure. The rods presented very high bending strength as a result of the homogeneous microstructure, and their strength increased rapidly as the interphase spacing decreased, reaching a maximum of 2.7 GPa for the rods grown at 750 mm/h. The bending strength remained constant up to 1300 K and decreased above this temperature. The relationship between the microstructure and the mechanical properties was established from the analysis of the microstructure and of the fracture mechanisms.     

Fabrication of novel multilayer Al2O3-(m-ZrO2)/t-ZrO2 fibrous ceramics composites

A novel layered microstructure in the Al₂O₃/ZrO₂ composites system was fabricated by the multipass extrusion method. The microstructure consisted with very fine alternate lamina of Al₂O₃-(m-ZrO₂) and t-ZrO₂. The composites were designed in such a way that a small group of 7 cylindrical alternate layers of Al₂O₃-(m-ZrO₂) and t-ZrO₂ made a concentric microgroup around 40 μm in diameter, with a common boundary layer between the adjacent groups. The thickness of both layers was around 2-3 μm. The microstructure was unidirectionally aligned throughout the composites. The composite microstructure was fibrous due to the unidirectional orientation of these microgroups. Detailed microstructure of the fabricated composites was characterized by SEM. The effect of the concentric layered microstructure on mechanical behavior was discussed. Material properties such as density, bending strength, Vickers hardness and fracture toughness were measured and evaluated depending on different sintering temperatures.     

Relationship between fracture toughness characteristics and morphology of sintered Al2O3 ceramics

The influence of sintering temperature and soaking time on fracture toughness of Al₂O₃ ceramics has been investigated. The samples were prepared by solid state sintering at 1500, 1600 and 1700 °C for different soaking time periods. The fracture toughness of the sintered samples was determined by inducing cracks using Vickers indentation technique. Microstructural investigations on fracture surfaces obtained by three point bend test mode were made and correlated with fracture toughness. Crack deflection in the samples sintered at 1500 and 1600 °C for which ranges of fracture toughness are 5.2–5.4 and 5.0–5.6 MPa m^1/2 respectively, are found. The samples sintered at 1700 °C have lower fracture toughness ranging between 4.6 and 5.0 MPa m^1/2. These samples have larger grains and transgranular fracture mode is predominant. The crack deflection has further been revealed by SEM and AFM observations on fracture surface and fracture surface roughness respectively.     

Memory characteristics of multi-stacked thin films using La2O3 and LaAlO3 as charge trap layer

Al₂O₃/La₂O₃/Al₂O₃ (ALA) and Al₂O₃/LaAlO₃/Al₂O₃ (A/LAO/A) multi-stacked films were deposited on Si substrates by MOCVD. No interfacial layers (Al_xSi_yO_z) were observed in TEM images, and the thickness ratio of the tunnel oxide (bottom oxide), trap layer (middle oxide), and blocking oxide (top oxide) was about (1:1.3:3) in both films. Memory windows of the (ALA) and (A/LAO/A) films were 1.31 V and 3.13 V, respectively. Each value in the program/erase cycle test was maintained for up to 10⁴ cycles.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Influence of sintering temperature and holding time on the densification, phase transformation, microstructure and properties of hot pressing WC-40 vol.%Al2O3 composites

WC-40 vol.%Al₂O₃ composites were prepared by high energy ball milling followed by hot pressing. The tungsten carbide (WC) and commercial alumina (Al₂O₃) powders composed of amorphous Al₂O₃, boehmite (AlOOH) and χ-Al₂O₃ were used as the starting materials. The phase transformation during sintering, the influence of sintering temperature and holding time on the densification, microstructure, Vickers hardness and fracture toughness and the toughening effects of WC-40 vol.%Al₂O₃ composites were investigated. The results showed that the amorphous Al₂O₃, AlOOH and χ-Al₂O₃ were transformed to α-Al₂O₃ completely during the sintering process. With the increasing sintering temperature and holding time, the relative density increased and both the Vickers hardness and fracture toughness increased initially to the maximum values and then decreased. When the as milled powders were hot pressed at 1540 °C for 90 min, a relative density of 97.98% and a maximum hardness of 18.65 GPa with an excellent fracture toughness of 10.43 MPa m^1/2 of WC-40 vol.%Al₂O₃ composites were obtained.     

Effect of Al2O3 particle size on preparation and properties of ZTA ceramics formed by gelcasting

Zirconia-toughened alumina (ZTA) ceramics were prepared using three different kinds of Al₂O₃ powders (marked PW-A average particle size: 7.53 μm, marked PW-B average particle size: 1.76 μm, marked PW-C average particle size: 0.61 μm) by gelcasting. Effect of Al₂O₃ particle size on zeta potential, dispersant dosage and solid volume fractions of ZTA suspensions as well as the mechanical properties of ZTA green bodies and ceramics were investigated. The optimum dosages of dispersant for ZTA suspensions prepared by PW-A, PW-B and PW-C are 0.4 wt%, 0.5 wt% and 0.7 wt%, respectively. The highest solid volume fractions of ZTA suspensions can reach 62 vol% (SP-A), 60 vol% (SP-B) and 52 vol% (SP-C), respectively. The green bodies show a bending strength as high as 20 MPa, which can meet the requirement of machining. The Al₂O₃ powder with fine particle size is beneficial to the improvement of mechanical properties. The ZTA ceramics prepared by PW-B Al₂O₃ powder show the highest bending strength (680 MPa) and toughness (7.49 MPa m^1/2).     

Processing and physical properties of Al2O3/aluminum alloy composites

Porous aluminum oxide (Al₂O₃) preforms were formed by sintering in air at 1200 °C for 2 h. A356, 6061, and 1050 aluminum alloys were infiltrated into the preforms by squeeze casting in order to fabricate Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites, respectively, with different volumes of aluminum alloy content. The content of aluminum alloy in the composites was 10–40% by volume. The resistivity of Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites decreased dramatically from 6.41 × 10¹² to 9.77 × 10⁻⁴, 7.28 × 10⁻⁴, and 6.24 × 10⁻⁴ Ω m, respectively, the four-points bending strength increased from 397 to 443, 435.1, 407.2 MPa, respectively, and the deviations were smaller than 2%. From SEM microstructural analysis and TEM bright field images, the pore volume fraction and the relative density of the composites were the most important factors that affected the physical and mechanical properties. The ceramic phase and alloy phase in Al₂O₃/aluminum alloy composites were found to be homogenized and uniformly distributed using electrical and mechanical properties analysis, microstructure analysis, and image analysis.     

Effects of CaSiO3 addition on sintering behavior and microwave dielectric properties of Al2O3 ceramics

The effects of CaSiO₃ addition on the sintering behavior and microwave dielectric properties of Al₂O₃ ceramics have been investigated. The addition of CaSiO₃ into Al₂O₃ ceramics resulted in the emergence of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which acting as liquid sintering aids can effectively lower the sintering temperature of Al₂O₃ ceramic. The Q × f value of Al₂O₃-CaSiO₃ ceramics decreased with the CaSiO₃ addition increasing because of the lower Q × f value of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈. Compared with the pure CaSiO₃ ceramic, the Al₂O₃-CaSiO₃ ceramic with 20 wt% CaSiO₃ addition possessed good dielectric properties of ?_r = 9.36 and Q × f = 13,678 GHz at the similar sintering temperature.     

Effects of Al2O3 addition on the sintering behavior and microwave dielectric properties of CaSiO3 ceramics

The effects of Al₂O₃ addition on the densification, structure and microwave dielectric properties of CaSiO₃ ceramics have been investigated. The Al₂O₃ addition results in the presence of two distinct phases, e.g. Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which can restrict the growth of CaSiO₃ grains by surrounding their boundaries and also improve the bulk density of CaSiO₃-Al₂O₃ ceramics. However, excessive addition (≥2 wt%) of Al₂O₃ undermines the microwave dielectric properties of the title ceramics since the derived phases of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈ have poor quality factor. The optimum amount of Al₂O₃ addition is found to be 1 wt%, and the derived CaSiO₃-Al₂O₃ ceramic sintered at 1250 °C presents improved microwave dielectric properties of ?_r = 6.66 and Q × f = 24,626 GHz, which is much better than those of pure CaSiO₃ ceramic sintered at 1340 °C (Q × f = 13,109 GHz).     

Selective oxidation of methanol to dimethoxymethane over acid-modified V2O5/TiO2 catalysts

Selective oxidation of methanol to dimethoxymethane (DMM) was conducted in a fixed-bed reactor over an acid-modified V₂O₅/TiO₂ catalyst. The influence of the acid modification on its structure, redox and acidic properties, and catalytic performance for methanol oxidation were investigated. The results indicated that the content of vanadia in the catalyst exhibits a vital influence on the dispersion of vanadium species, while the acid modification can enhance its surface acidity. Proper amounts of the acid (W() = 15%) and V₂O₅ (W(V₂O₅) = 15%) components loaded in the acid-modified V₂O₅/TiO₂ catalyst are able to build a bi-functional circumstance that is favorable for the formation of DMM with high activity and selectivity. As a result, for the selective oxidation of methanol, the H₂SO₄-modified V₂O₅/TiO₂ catalyst gives a much higher DMM yield at 150 °C than the unmodified one.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.     

Development of input output relationships for self-healing Al2O3/SiC ceramic composites with Y2O3 additive using design of experiments

Al₂O₃/SiC ceramic composites with Y₂O₃ as an additive, was synthesized using the Taguchi method of design of experiments, so as to develop statistically sound input output relationships. The proportion of SiC was varied from 12 to 21 vol.% whereas that of Y₂O₃ was varied from 2.5 to 4 vol.%. The composites were sintered at 1500 °C for a soaking time period of 12 h in an air atmosphere. Cracks were induced on the composite surface using a Vickers indenter with a load varying between 20 and 40 kg. Fractographical analyses have been carried out using optical and/or scanning electron microscopy to investigate the surface crack propagation behavior. Thermal aging at 1300 °C in the time range of 0.5-12.5 h was applied to find optimal conditions for healing of the pre-cracked samples. The output parameters such as crack length, healed crack length, hardness and fracture toughness of the samples were correlated with appropriate inputs such as contents of SiC and Y₂O₃, crack-healing temperature, healing time, compaction pressure, indentation load using statistical analysis. Further, the extent of influence, exerted by pertinent input parameters on output parameters, was also identified.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Indirect selective laser sintering of epoxy resin-Al2O3 ceramic powders combined with cold isostatic pressing

To fabricate Al₂O₃ ceramic components with complex shape, selective laser sintering (SLS) combined with cold isostatic pressing (CIP) process was used to consolidate Al₂O₃ powder with additive of epoxy resin E06 (ER06) and polyvinyl alcohol (PVA). The starting material preparation combined spray drying with mechanical mixing to formulate compound powder consisting of PVA (1.5 wt%), ER06 (8 wt%) and Al₂O₃ and provide a good fluidity for SLS. Experimental investigations were carried the shrinkage, relative density, bending strength of Al₂O₃-ER06 SLS specimens in order to optimize the laser sintering parameters. It was found that Al₂O₃-ER06 SLS specimens represented acceptable shrinkage, high density and bending strength when laser power, scanning speed, scanning space and layer thickness were, respectively, 21 W, 1600 mm/s, 100 μm and 150 μm. Following that, the SLS specimens were processed through CIP to eliminate the pores in green ceramics. Finally, the optimized SLS/CIP Al₂O₃ specimens were debinded, sintered to produce crack-free Al₂O₃ bodies. The final Al₂O₃ components achieved a relative high density of more than 92% after furnace sintering. The study shows a novel and promising approach to fabricate complex ceramic matrix and ceramic components via indirect SLS and CIP process.     

Mechanical properties of SiCp/Al2O3 ceramic matrix composites prepared by directed oxidation of an aluminum alloy

Silicon carbide particulate reinforced alumina matrix composites were fabricated using DIrected Metal OXidation (DIMOX) process. Continuous oxidation of an Al-Si-Mg-Zn alloy with appropriate dopants along with a preform of silicon carbide has led to the formation of alumina matrix surrounding silicon carbide particulates. SiC_p/Al₂O₃ ceramic matrix composites fabricated by the DIMOX process, possess enhanced mechanical properties such as flexural strength, fracture toughness and wear resistance, all at an affordable cost of fabrication. SiC_p/Al₂O₃ matrix composites were investigated for mechanical properties such as flexural strength, fracture toughness and hardness; the composite specimens were evaluated using standard procedures recommended by the ASTM. The SiC_p/Al₂O₃ ceramic matrix composites with SiC volume fractions from 0.35 to 0.43 were found to possess average bend strength in range 158-230 MPa and fracture toughness was found to be in range of 5.61-4.01 MPa√m. The specimen fractured under three-point loading as observed under scanning electron microscope was found to fail in brittle manner being the dominant mode. Further the composites were found to possess lower levels of porosity, among those prepared by DIMOX process.     

Microstructure, growth mechanism and mechanical property of Al2O3-based eutectic ceramic in situ composites

Directionally solidified Al₂O₃-based eutectic ceramic in situ composites with inherently high melting point, low density, excellent microstructure stability, outstanding resistance to creep, corrosion and oxidation at elevated temperature, have attracted significant interest as promising candidate for high-temperature application. This paper reviews the recent research progress on Al₂O₃-based eutectic ceramic in situ composites in State Key Laboratory of Solidification Processing. Al₂O₃/YAG binary eutectic and Al₂O₃/YAG/ZrO₂ ternary eutectic ceramics are prepared by laser zone melting, electron beam floating zone melting and laser direct forming, respectively. The processing control, solidification characteristic, microstructure evolution, eutectic growth mechanism, phase interface structure, mechanical property and toughening mechanism are investigated. The high thermal gradient and cooling rate during solidification lead to the refined microstructure with minimum eutectic spacing of 100 nm. Besides the typical faceted/faceted eutectic growth manner, the faceted to non-faceted growth transition is found. The room-temperature hardness H_V and fracture toughness K_IC are measured with micro-indentation method. For Al₂O₃/YAG/ZrO₂, K_IC = 8.0 ± 2.0 MPa m^1/2 while for Al₂O₃/YAG, K_IC = 3.6 ± 0.4 MPa m^1/2. It is expectable that directionally solidified Al₂O₃-based eutectic ceramics are approaching practical application with the advancement of processing theory, technique and apparatus.