Formation of austenite in 1.5 pct Mn steels

The formation of austenite from different microstructural conditions has been studied in a series of 1.5 pct Mn steels that had been heated in and above the intercritical (α+ γ) region of the phase diagram. The influence of variables such as cementite morphology, initial structural state of the ferrite and the carbon content has been assessed in terms of their respective effects on the kinetics of austenite formation and final microstructure. Austenite was found to form preferentially on ferrite-ferrite grain boundaries for all initial structures. The results of this study have shown that the 1.5 pct Mn has lowered both the AC₃ and AC₁, lines causing large amounts of austenite to form in low carbon steel. The kinetics of austenite formation at 725 °C were not only very slow but also were approximately independent of the amount formed. Austenite appeared to form slightly more rapidly from cold rolled ferrite than from recrystallized ferrite or ferrite-pearlite structures.     

Interrelations of cooling rate,microstructure, and mechanical properties in four HSLA steels

The present study was carried out on four steels containing 0.1 pct C-1.5 pct Mn-0.003 pct B* in common, with additions of 1 pct Cr, 0.5 pct Mo, 0.25 pct Mo + 1 pct Cr, 0.2 pct Ti + 1 pct Cr. They were designated, accordingly, as Cr, Mo, Mo-Cr, and Cr-Ti steels. All the steels exhibited a complete lath martensite microstructure with thin interlaths of retained austenite (≈0.05 pct) in the quenched condition. The normalized microstructures, granular bainite, contained massive areas of ferrite and granules of bainite laths. Both microconstituents contained a fine dispersion of cementite particles (size ≈50 Å) together with high dislocation densities. A mechanism explaining their for-mation has been given. The Cr steel, due to its low hardenability, showed in addition polygonal ferrite in the neighborhood of the so-called M-A constituent (twinned martensite and/or austenite). The annealed microstructure (using a cooling rate of 0.033 °C s^?1) of the Cr steel consisted of coarse ferrite-pearlite. Addition of 0.2 pct Ti to the Cr steel markedly refined the structure, whereas an addition of 0.25 pct Mo altered the microstructure to ferrite-lower bainite. In the 0.5 pct Mo steel, polygonal ferrite was found to be completely missing. The mechanical properties of the four steels after quenching, normalizing, and annealing were investigatedvia hardness and tensile test mea-surements. An empirical equation, relating the ultimate tensile strength to the steel composition, for steels that had granular bainite microstructures in the normalized condition, was proposed. The fracture surfaces exhibited cleavage and variable-size dimples depending on the microstructure and steel composition.     

Nucleation sites for ultrafine ferrite produced by deformation of austenite during single-pass strip rolling

An austenitic Ni-30 wt pct Fe alloy, with a stacking-fault energy and deformation characteristics similar to those of austenitic low-carbon steel at elevated temperatures, has been used to examine the defect substructure within austenite deformed by single-pass strip rolling and to identify those features most likely to provide sites for intragranular nucleation of ultrafine ferrite in steels. Samples of this alloy and a 0.095 wt pct C-1.58Mn-0.22Si-0.27Mo steel have been hot rolled and cooled under similar conditions, and the resulting microstructures were compared using transmission electron microscopy (TEM), electron diffraction, and X-ray diffraction. Following a single rolling pass of ∼40 pct reduction of a 2mm strip at 800 °C, three microstructural zones were identified throughout its thickness. The surface zone (of 0.1 to 0.4 mm in depth) within the steel comprised a uniform microstructure of ultrafine ferrite, while the equivalent zone of a Ni-30Fe alloy contained a network of dislocation cells, with an average diameter of 0.5 to 1.0 μm. The scale and distribution and, thus, nucleation density of the ferrite grains formed in the steel were consistent with the formation of individual ferrite nuclei on cell boundaries within the austenite. In the transition zone, 0.3 to 0.5 mm below the surface of the steel strip, discrete polygonal ferrite grains were observed to form in parallel, and closely spaced “rafts” traversing individual grains of austenite. Based on observations of the equivalent zone of the rolled Ni-30Fe alloy, the ferrite distribution could be correlated with planar defects in the form of intragranular microshear bands formed within the deformed austenite during rolling. Within the central zone of the steel strip, a bainitic microstructure, typical of that observed after conventional hot rolling of this steel, was observed following air cooling. In this region of the rolled Ni-30Fe alloy, a network of microbands was observed, typical of material deformed under plane-strain conditions.     

Molybdenum accumulation at ferrite: Austenite interfaces during isothermal transformation of an Fe-0.24 pct C-0.93 pct Mo alloy

A scanning transmission electron microscope (STEM) technique was used to measure Mo concentrations at ferrite:austenite (α:γ) interfaces in an Fe-0.24 pct C-0.93 pct Mo alloy partially transformed at 650°C, 630°C, and 610°C. These concentrations were quite small at 650°C, which is just below the bay temperature of the time-temperature-transformation (TTT) curve for the initiation of ferrite formation. There were larger concentrations at 630°C, a temperature at which transformation stasis (incomplete transformation) occurred. Concentrations at 610°C were intermediate between the values observed at 650°C and 630°C. The average accumulation at the latter temperatures increased appreciably as a function of transformation time. After each heat treatment, there was considerable variation in Mo accumulation from one α:γ interface to another and, to a lesser extent, from one region to another along the same interface. These higher Mo concentrations were deduced to have developed largely through volume diffusion of Mo, mainly through ferrite, to interfaces whose ledgewise growth had been interrupted by growth stasis. (Mo₂C precipitation at α:γ boundaries occurred only at the end of growth stasis.) It appears that only a very small amount of Mo segregation is needed, probably at specific interfacial sites, in order to produce growth cessation. Growth kinetics anomalies of this kind continue to provide the best evidence available for the operation of a coupled-solute drag effect. This article is based on a presentation given in the symposium “The Effect of Alloying Elements on the Gamma to Alpha Transformation in Steels,” October 6, 2002, at the TMS Fall Meeting in Columbus, Ohio, under the auspices of the McMaster Centre for Steel Research and the ASM-TMS Phase Transformations Committee.     

Ferrite recrystallization and austenite formation in cold-rolled intercritically annealed steel

The recrystallization of ferrite and austenite formation during intercritical annealing were studied in a 0.08C-1.45Mn-0.21Si steel by light and transmission electron microscopy. Normalized specimens were cold rolled 25 and 50 pct and annealed between 650 °C and 760 °C. Recrystallization of the 50 pct deformed ferrite was complete within 30 seconds at 760 °C. Austenite formation initiated concurrently with the ferrite recrystallization and continued beyond complete recrystallization of the ferrite matrix. The recrystallization of the deformed ferrite and the spheroidization of the cementite in the deformed pearlite strongly influence the formation and distribution of austenite produced by intercritical annealing. Austenite forms first at the grain boundaries of unrecrystallized and elongated ferrite grains and the spheroidized cementite colonies associated with ferrite grain boundaries. Spheroidized cementite particles dispersed within recrystallized ferrite grains by deformation and annealing phenomena were the sites for later austenite formation.     

Effects of austenitizing temperature on the kinetics of the proeutectoid ferrite reaction at constant austenite grain size in an Fe-C alloy

Austenitizing an Fe-0.23 pct C alloy at 1300°C and further at 900°C prior to isothermal transformation was found to increase the growth kinetics of grain boundary ferrite allotriomorphs while decreasing their rate of nucleation. A scanning Auger microprobe was used to establish that sulfur segregates to the austenite grain boundaries and does so increasingly with decreasing austenitizing temperature. A binding free energy of sulfur to these boundaries of approximately 13 kcal/mole (54.4 kj/mole) was calculated from theMcLean adsorption isotherm. The kinetic results were explained in terms of preferential reduction of the austenite grain boundary energy decreasig nucleation kinetics, and adsorption of sulfur at α:γ boundaries increasing the carbon concentration gradient in austenite driving growth.     

The 885° f (475° c) embrittlement of ferritic stainless steels

The 885odgF (475°C) embrittlement of seven heats of chromium steels was investigated: four vacuum-melted heats with C + N < 0.008 pct and 14 pct Cr, 14 pet Cr-2 pet Mo, 18 pct Cr, or 18 pet Cr-2 pet Mo, and three air-melted heats with C + N > 0.09 pet and 18 pet Cr, 18 pct Cr-2 pet Mo, or 18 pet Cr-2 pet Mo-0.5 pct Ti. The steels were heated at 600° (316°), 700° (371°), 800° (427°), 900° (482°), and 1000°F (538°C) for various times up to 4800 h and the influence of this aging was investigated by hardness measurements, impact tests, and electron metallography. It was demonstrated that the embrittlement due to 885°F (475°C) exposure was caused by precipitation of a chromium-rich α^’ phase on dislocations. The nucleation rate of α^’ was calculated with the aid of Becker’s theory and the results were used to extrapolate experimental data obtained in this study. After an exposure of about 1000 h at 1000°F (538°C), a decrease in room temperature toughness was observed for all steels investigated. The decrease in toughness was not caused by immobilization of dislocations by α^’, but by precipitation of carbonitrides.     

The mechanical stability of austenite and cryogenic toughness of ferritic Fe-Mn-AI Alloys

In an attempt to understand the role of retained austenite on the cryogenic toughness of a ferritic Fe-Mn-AI steel, the mechanical stability of austenite during cold rolling at room temperature and tensile deformation at ambient and liquid nitrogen temperature was investigated, and the microstructure of strain-induced transformation products was observed by transmission electron microscopy (TEM). The volume fraction of austenite increased with increasing tempering time and reached 54 pct after 650 °C, 1-hour tempering and 36 pct after 550 °C, 16-hour tempering. Saturation Charpy impact values at liquid nitrogen temperature were increased with decreasing tempering temperature, from 105 J after 650 °C tempering to 220 J after 550 °C tempering. The room-temperature stability of austenite varied significantly according to the(α + γ) region tempering temperature;i.e., in 650 °C tempered specimens, 80 to 90 pct of austenite were transformed to lath martensite, while in 550 °C tempered specimens, austenite remained untransformed after 50 pct cold reductions. After tensile fracture (35 pct tensile strain) at -196 °C, no retained austenite was observed in 650 °C tempered specimens, while 16 pct of austenite and 6 pct of e-martensite were observed in 550 °C tempered specimens. Considering the high volume fractions and high mechanical stability of austenite, the crack blunting model seems highly applicable for improved cryogenic toughness in 550 °C tempered steel. Other possible toughening mechanisms were also discussed. Formerly Graduate Student, Seoul National University.     

Continuous cooling transformation kinetics of thermomechanically worked low-carbon austenite

Continuous cooling transformation diagrams were determined for molybdenum-boron steels containing 0.24, 0.4, and 0.66 pct Mo with 0.1 pct C, and also 0.4 pct Mo with 0.2 pct C, after thermomechanically working by compressive deformation to 12, 25, and 50 pct reduction at 830°C (1525°F), as well as for the steels in the underformed condition. In underformed specimens, higher carbon or molybdenum decreased the limiting cooling rate for the avoidance of polygonal ferrite formation. The same was true for deformed specimens, although increased deformation raised the limiting cooling rates of all compositions. The limiting cooling rate for polygonal ferrite formation increased exponentially with austenite, deformation, as measured by true strain. Thermomechanical working also raised bainite start temperatures at fast cooling rates and caused small increases in martensite start temperatures.     

Determination of the Fe-Ni and Fe-Ni-P phase diagrams at low temperatures (700 to 300 °C)

The α + γ two-phase fields of the Fe-Ni and Fe-Ni (P saturated) phase diagrams have been determined in the composition range 0 to 60 wt pet Ni and in the temperature range 700 to 300 °C. The solubility of Ni in (FeNi)₃P was measured in the same temperature range. Homogeneous alloys were austenitized and quenched to form α₂, martensite, then heat treated to formα (ferrite) + γ (austenite). The compositions of the α and γ phases were determined with electron microprobe and scanning transmission electron microscope techniques. Retrograde solubility for the α/(α + γ) solvus line was demonstrated exper-imentally. P was shown to significantly decrease the size of the α + γ two-phase field. The maximum solubility of Ni in α is 6.1 ± 0.5 wt pct at 475 °C and 7.8± 0.5 wt pct at 450 °C in the Fe-Ni and Fe-Ni (P saturated) phase diagrams, respectively. The solubility of Ni in α is 4.2 ± 0.5 wt pct Ni and 4.9 ± 0.5 wt pct Ni at 300 °C in the Fe-Ni and Fe-Ni (P saturated) phase diagrams. Ternary Fe-Ni-P isothermal sections were constructed between 700 and 300 °C. Formerly Research Assistant in Department of Metallurgy & Materials Engineering, Lehigh University, Bethlehem, PA.     

Effects of Initial Structure and Reversion Temperature on Austenite Nucleation Site in Pearlite and Ferrite–Pearlite

Austenite nucleation sites were investigated in near-eutectoid 0.8 mass pct C steel and hypoeutectoid 0.4 mass pct C steel samples with full pearlite and ferrite–pearlite initial structures, respectively. In particular, the prior austenite grain size had been coarsened to compare grain boundaries in the hierarchical pearlite structure, i.e., the low-angle pearlite colony and high-angle block boundaries with ferrite/pearlite interfaces in the austenite nucleation ability. When the full pearlite in 0.8 mass pct C steel underwent reversion at a relatively low temperature, austenite grains preferentially formed at pearlite block boundaries. Consequently, when the full pearlite with the coarse block structure underwent reversion just above the eutectoid temperature, the reversion took a long time due to the low nucleation density. However, austenite grains densely formed at the pearlite colony boundaries as well, as the reversion temperature became sufficiently high. On the other hand, when ferrite–pearlite in the 0.4 mass pct C steel underwent reversion to austenite, the ferrite/pearlite interface acted as a more preferential austenite nucleation site than the pearlite block boundary even in the case of low-temperature reversion. From these results, it can be concluded that the preferential austenite nucleation site in carbon steels is in the following order: ferrite/pearlite interface?>?pearlite block?>?colony boundaries. In addition, orientation analysis results revealed that ferrite restricts the austenite nucleation more strongly than pearlitic ferrite does, which contributes to the preferential nucleation at ferrite/pearlite interfaces. This suggests that austenite grains formed at a ferrite/pearlite interface tend to have an identical orientation even under high-temperature reversion. Therefore, it is thought that the activation of austenite nucleation within pearlite by increasing the reversion temperature may be effective for rapid austenitization and the grain refinement of austenite structure after the completion of reversion in carbon steels.     

Selective Oxidation and Reactive Wetting of 1.0 Pct Si-0.5 Pct Al and 1.5 Pct Si TRIP-Assisted Steels

Heat treatments were performed using an isothermal bainitic transformation (IBT) temperature compatible with continuous hot-dip galvanizing on two high Al–low Si transformation induced plasticity (TRIP)-assisted steels. Both steels had 0.2 wt pct C and 1.5 wt pct Mn; one had 1.5 wt pct Al and the other had 1 wt pct Al and 0.5 wt pct Si. Two different intercritical annealing (IA) temperatures were used, resulting in intercritical microstructures of 50 pct ferrite (α)-50 pct austenite (γ) and 65 pct α-35 pct γ. Using the IBT temperature of 465 °C, five IBT times were tested: 4, 30, 60, 90, and 120 seconds. Increasing the IBT time resulted in a decrease in the ultimate tensile strength (UTS) and an increase in the uniform elongation, yield strength, and yield point elongation. The uniform elongation was higher when using the 50 pct α-50 pct γ IA temperature when compared to the 65 pct α-35 pct γ IA temperature. The best combinations of strength and ductility and their corresponding heat treatments were as follows: a tensile strength of 895 MPa and uniform elongation of 0.26 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 90-second IBT time; a tensile strength of 880 MPa and uniform elongation of 0.27 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 120-second IBT time; and a tensile strength of 1009 MPa and uniform elongation of 0.22 for the 1 pct Al-0.5 pct Si TRIP steel at the 50 pct γ IA temperature and 120-second IBT time.     

Spatially resolved X-ray diffraction mapping of phase transformations in the heat-affected zone of carbon-manganese steel arc welds

Phase transformations that occur in the heat-affected zone (HAZ) of gas tungsten arc welds in AISI 1005 carbon-manganese steel were investigated using spatially resolved X-ray diffraction (SRXRD) at the Stanford Synchrotron Radiation Laboratory. In situ SRXRD experiments were performed to probe the phases present in the HAZ during welding of cylindrical steel bars. These real-time observations of the phases present in the HAZ were used to construct a phase transformation map that identifies five principal phase regions between the liquid weld pool and the unaffected base metal: (1) α-ferrite that is undergoing annealing, recrystallization, and/or grain growth at subcritical temperatures, (2) partially transformed α-ferrite co-existing with γ-austenite at intercritical temperatures, (3) single-phase γ-austenite at austenitizing temperatures, (4) δ-ferrite at temperatures near the liquidus temperature, and (5) back transformed α-ferrite co-existing with residual austenite at subcritical temperatures behind the weld. The SRXRD experimental results were combined with a heat flow model of the weld to investigate transformation kinetics under both positive and negative temperature gradients in the HAZ. Results show that the transformation from ferrite to austenite on heating requires 3 seconds and 158°C of superheat to attain completion under a heating rate of 102°C/s. The reverse transformation from austenite to ferrite on cooling was shown to require 3.3 seconds at a cooling rate of 45 °C/s to transform the majority of the austenite back to ferrite; however, some residual austenite was observed in the microstructure as far as 17 mm behind the weld.     

The morphology,crystallography, and mechanism of carbide precipitation in an Fe-0.12 Pct C-3.28 Pct Ni alloy

Carbide precipitation during the eutectoid decomposition of austenite has been studied in an Fe-0.12 pct C-3.28 pct Ni alloy by transmission electron microscopy (TEM) supplemented by optical microscopy. Nodular bainite which forms during the latter stages of austenite decomposition at 550 °C exhibits two types of carbide arrangement: (a) banded interphase boundary carbides with particle diameters of about 20 to 90 nm and mean band spacings between 180 and 390 nm and (b) more randomly distributed (“nonbanded”) elongated particles exhibiting a wide range of lengths between 33 and 2500 nm, thicknesses of approximately 11 to 50 nm, and mean intercarbide spacings of approximately 140 to 275 nm. Electron diffraction analysis indicated that in both cases, the carbides are cementite, obeying the Pitsch orientation relationship with respect to the bainitic ferrite. The intercarbide spacings of both morphologies are significantly larger than those previously reported for similar microstructures in steels containing alloy carbides other than cementite (e.g., VC, TiC). Both curved and straight cementite bands were observed; in the latter case, the average plane of the interphase boundary precipitate sheets was near {110}_α//{011}_c consistent with cementite precipitation on low-energy {110}_α//{111}_γ ledge terrace planes (where α,β, andc refer to ferrite, austenite, and cementite, respectively). The results also suggest that the first stage in the formation of the nonbanded form of nodular bainite is often the precipitation of cementite rods, or laths, in austenite at the α:γ interfaces of proeutectoid ferrite secondary sideplates formed earlier. Although these cementite rods frequently resemble the “fibrous” microstructures observed by previous investigators in carbide-forming alloy steels, they are typically much shorter than fibrous alloy carbides. The bainitic microstructures observed here are analyzed in terms of a previously developed model centered about the roles of the relative nucleation and growth rates of the product phases in controlling the evolution of eutectoid microstructures.     

Effect of interpass time on austenite grain refinement by means of dynamic recrystallization of austenite

A 0.06 pct C-0.3 pct Mn and a 0.07 pct C-0.6 pct Mn-0.028 pct Nb steel were deformed in torsion at a constant strain rate of 2/s. Two schedules were used. In schedule A, seven roughing passes executed between 1260°C and 1130°C were followed by a single large finishing pass with a strain of 3.5 at constant temperatures between 1010°C and 840°C. The time between roughing and finishing was 200 seconds. In schedule B, the seven roughing passes were followed by 10 finishing passes, again applied isothermally, with strains of 0.3 and interpass times of 0.6, 2, and 10 seconds. The results indicate that for the Nb steel, low rolling temperatures (870°C) and strains above 2 are required for complete dynamic recrystallization, which results in austenite grain sizes under 6μm. Cooled at a rate of 10°C/s, the dynamically recrystallized austenite grain structures transform into ferrite with grain sizes under 4 μ. Extrapolations from the present data suggest that at industrial strain rates and cooling rates, ferrite grain sizes under 2 μm should be achieved. Y.W. BOWDEN, formerly CSIRA Research Associate, Department of Mining and Metallurgical Engineering, McGill University     

Influence of Interfacial Structure upon Carbide Precipitation at Austenite : Ferrite Boundaries in an Fe-C-Mo Alloy

During conventional isothermal transformation of an Fe-0.11 pct C-1.95 pct Mo alloy, eutectoid decomposition occurs by the interphase boundary carbide precipitation and the fibrous carbide mechanisms at 770° to 825 °C. When proeutectoid ferrite is formed and then recrystallized within the α + γ region, and subsequently further transformed at 770° to 825 °C, however, both of these eutectoid decomposition mechanisms are rendered inoperative. Carbide precipitation occurs instead entirely as isolated particles. This result supports the deduction that carbide precipitation at austenite : ferrite boundaries can occur only when these boundaries are locally immobilized by a partially coherent interfacial structure. A general approach to explaining the development of planar and curved interphase boundary precipitation, fibrous structure, and pearlite is developed in terms of two crystallographic factors. Formerly Research Associate in the Department of Metallurgical Engineering, Michigan Technological University, Houghton, MI 49931 and the Department of Metallurgical Engineering and Materials Science, Carnegie-Mellon University, Pittsburgh, PA 15213 Formerly Graduate Student, Michigan Technological University, and Visiting Graduate Student, Camegie-Mellon University Formerly Professor at Michigan Technological University     

Analysis of the <Emphasis Type="Italic">γ</Emphasis> → <Emphasis Type="Italic">α</Emphasis> transformation in a C-Mn steel by phase-field modeling

This article deals with the austenite (γ) decomposition to ferrite (α) during cooling of a 0.10 wt pct C-0.49 wt pct Mn steel. A phase-field model is used to simulate this transformation. The model provides qualitative information on the microstructure that develops on cooling and quantitative data on both the ferrite fraction formed and the carbon concentration profile in the remaining austenite. The initial austenitic microstructure and the ferrite nucleation data, derived by metallographic examination and dilatometry, are set as input data of the model. The interface mobility is used as a fitting parameter to optimize the agreement between the simulated and experimental ferrite-fraction curve derived by dilatometry. A good agreement between the simulated α-γ microstructure and the actual α-pearlite microstructure observed after cooling is obtained. The derived carbon distribution in austenite during transformation provides comprehension of the nature of the transformation with respect to the interface-controlled or diffusion-controlled mode. It is found that, at the initial stage, the transformation is predominantly interface-controlled, but, gradually, a shift toward diffusion control takes place to a degree that depends on cooling rate.     

High temperature phase chemistries and solidification mode prediction in nitrogen-strengthened austenitic stainless steels

Nitronic 50 and Nitronic 50W, two nitrogen-strengthened stainless steels, were heat treated over a wide range of temperatures, and the compositions of the ferrite and austenite at each temperature were measured with analytical electron microscopy techniques. The compositional data were used to generate the (γ + δ phase field on a 58 pct Fe vertical section. Volume fractions of ferrite and austenite were calculated from phase chemistries and compared with volume fractions determined from optical micrographs. Weld solidification modes were predicted by reference to the Cr and Ni contents of each alloy, and the results were compared with predictions based on the ratios of calculated Cr and Ni equivalents for the alloys. Nitronic 50, which contained ferrite and austenite at the solidus temperature of 1370 °C, solidified through the eutectic triangle, and the weld microstructure was similar to that of austenitic-ferritic solidification. Nitronic 50W was totally ferritic at 1340 °C and solidified as primary delta ferrite. During heat treatments, Nitronic 50 and Nitronic 50W precipitated secondary phases, notably Z-phase (NbCrN), sigma phase, and stringered phases rich in Mn and Cr.     

A Eutectoid Reaction for the Decomposition of Austenite into Pearlitic Lamellae of Ferrite and M<Subscript>23</Subscript>C<Subscript>6</Subscript> Carbide in a Mn-Al Steel

We discovered a eutectoid reaction in an Fe-13.4Mn-3.0Al-0.63C (wt pct) steel after solution heat treatment at 1373 K (1100 °C) and holding at temperatures below 923 K (650 °C). The steel is single austenite at temperatures from 1373 K to 923 K (1100 °C to 650 °C). A eutectoid reaction involves the replacement of the metastable austenite by a more stable mixture of ferrite and M₂₃C₆ phases at temperatures below 923 K (650 °C). The mixture of ferrite and M₂₃C₆ is in the form of pearlitic lamellae. The morphology of the lamellae of the product phases is similar to that of pearlite in steels. Thus, we found a new pearlite from the eutectoid reaction of the Mn-Al steel featuring γ  → α + M₂₃C₆. A Kurdjumov–Sachs (K-S) orientation relationship exists between the pearlitic ferrite (α) and M₂₃C₆ (C6) grains, i.e., (110)_α // (111)_C6 and [[`1] \overline{1} 11]<sub>α</sub> // [0[`1] \overline{1} 1]_C6. The upper temperature limit for the eutectoid reaction is between 923 K and 898 K (650 °C and 625 °C).     

Solidification of M2 high speed steel

The freezing process in AISI type M2 high speed tool steel (6 pct W, 5 pct Mo, 4 pct Cr, 2 pct V, 0.8 pct C) was studied by metallographic and thermal analysis techniques. Unidirectional solidification of small laboratory melts in a modified crystal growing apparatus was employed to provide metallographic sections of known macroscopic growth direction. Also cooling curves were obtained on 40 g specimens solidified in thimble crucibles. X-ray microradiography, electron probe scanning techniques, and quantitative microanalysis of dendrites and interdendritic carbides were extensively used to supplement conventional metallography. Carbon and vanadium contents of M2 were varied in order to observe the effect of an austenite and ferrite stabilizer on the thermal analysis curves and microstructure. The nonequilibrium freezing process in M2 includes three major liquid-solid reactions: 1) Liquid → Ferrite, 1435°C; 2) Liquid + Ferrite → Austenite, 1330°C; 3) Liquid → Austenite + M₆C + MC, 1240°C. These reactions account for the as-cast structure of the commercial alloy. The addition of carbon depresses the liquidus (1) and solidus temperatures (3) and narrows the gap between the liquidus (1) and peritectic transformation (2). This gap is eliminated at > 1.39 wt pct C, where the initial freezing reaction is the crystallization of austenite. The accompanying microstructural change is the elimination of σ eutectoid dendrite cores. The addition of vanadium promotes ferrite formation by strongly depressing the peritectic reaction and thus widening the gap between the liquidus and the peritectic.