O2/N2、O2/CO2和O2/CO2/NO气氛下煤粉燃烧NOx排放特性

利用滴管炉研究了O₂/N₂、O₂/CO₂和O₂/CO₂/NO气氛下煤燃烧过程中NO_x的排放特性。实验结果表明,在O₂/N₂和O₂/CO₂气氛下,高温或高O₂浓度均使NO排放量增加。O₂/CO₂气氛下NO排放量比O₂/N₂气氛下NO排放量低大约30%～40%。在O₂/CO₂/NO气氛下,温度不同时,O₂浓度变化对NO排放量的影响规律不同,对循环NO降解的影响规律也不同。高温不利于循环NO降解。随停留时间的延长NO排放量出现两个峰值。     

O2/CO2气氛下煤燃烧SO2/NO析出特性

在水平管式炉上研究了O₂浓度、CO₂浓度、温度及石灰石添加等各参数对O₂/CO₂气氛下徐州烟煤和龙岩无烟煤燃烧过程中SO₂/NO排放特性的影响。结果发现,O₂/CO₂气氛下,烟煤和无烟煤燃烧SO₂/NO的析出规律与空气气氛下不同,同等O₂浓度下析出量比空气气氛下小。O₂/CO₂气氛下,随着O₂浓度的提高,烟煤和无烟煤SO₂/NO排放量均增大;随着CO₂浓度的升高, SO₂/NO排放量均减小。O₂/CO₂气氛下,石灰石添加对SO₂排放的抑制作用低于空气气氛下;石灰石添加对NO的排放有一定减排作用。对煤灰的元素分析显示O₂/CO₂燃烧对SO₂的抑制主要是由于煤灰的自固硫能力增强,而对NO的减排作用则是促进燃料N向其他含N气体的转换。     

O2/CO2气氛下煤燃烧SO2/NO析出特性

在水平管式炉上研究了O₂浓度、CO₂浓度、温度及石灰石添加等各参数对O₂/CO₂气氛下徐州烟煤和龙岩无烟煤燃烧过程中SO₂/NO排放特性的影响。结果发现,O₂/CO₂气氛下,烟煤和无烟煤燃烧SO₂/NO的析出规律与空气气氛下不同,同等O₂浓度下析出量比空气气氛下小。O₂/CO₂气氛下,随着O₂浓度的提高,烟煤和无烟煤SO₂/NO排放量均增大;随着CO₂浓度的升高, SO₂/NO排放量均减小。O₂/CO₂气氛下,石灰石添加对SO₂排放的抑制作用低于空气气氛下;石灰石添加对NO的排放有一定减排作用。对煤灰的元素分析显示O₂/CO₂燃烧对SO₂的抑制主要是由于煤灰的自固硫能力增强,而对NO的减排作用则是促进燃料N向其他含N气体的转换。     

O2/CO2气氛煤焦的燃烧及其孔隙结构变化

采用热力工况与实际煤粉炉相近的沉降炉实验装置,制备了不同环境气氛下(O2/N2及O2/CO2气氛)、不同燃尽率的煤焦试样,并采用低温氮吸附仪和扫描电子显微镜测定了其孔隙结构和表面形貌.结果表明,在相同的操作条件下,相同O2浓度的O2/CO2气氛下煤焦的燃烧速率较慢、燃尽率较低,各试样的孔比表面积和比孔容积均较小.两种气氛下燃尽过程孔结构参数(SBET和VBJH)均呈减小趋势,且在孔径变化较明显的区域内(<5 nm)在CO2气氛下煤焦的孔径分布较小且与煤种相关.SEM图像显示CO2气氛下的煤焦表面致密,孔隙较少,其定性结果与N2吸附法的定量测量结果吻合较好.     

煤在O2/CO2中燃烧的Nox释放规律

利用一维沉降炉,对3种煤在O₂/CO₂和空气两种气氛下燃烧NO_x析出特性进行了比较,分析了炉膛温度、过量空气系数对NO_x生成量的影响,并对O₂/CO₂气氛下NO_x的生成和破坏机理进行了分析.研究发现两种气氛下NO_x都有一个峰值出现,挥发分含量高的煤种峰值靠前, 挥发分含量低的煤种峰值靠后,O₂/CO₂条件下,峰值出现较空气条件下提前且有所下降;空气条件下NO_x的生成量随温度提高较快地增加,而O₂/CO₂气氛中NO_x的生成量随温度变化比较缓慢;在两种气氛下NO_x的峰值均随过量空气系数的增加而增加,高挥发分煤在O₂/CO₂气氛下NO_x峰值低于空气条件下峰值,而低挥发分煤则受影响较小.     

沉淀法SiO2包覆纳米CaCO3吸附剂性能

以CO₂为沉淀剂,Na₂SiO₃为硅源,制备了SiO₂包覆纳米CaCO₃吸附剂。TEM测试证实纳米CaCO₃表面包覆一层SiO₂膜, 用SEM & EDX 测试5个包硅样品Si含量为0.67%～4.93%。采用TGA考察吸附剂的分解温度及600℃、20% CO₂条件下的吸附性能。结果表明：采用CO₂沉淀法包覆SiO₂后,与未包硅的纳米CaCO₃相比,分解温度降低9～42℃。纳米SiO₂/CaCO₃吸附剂的循环吸附率、吸附容量、吸附速率均随Si含量的减小先增加后降低。Si含量为1.05%的纳米SiO₂/CaCO₃吸附剂显示最佳吸附性能,第1、5次循环吸附容量分别为8.9、6.0 mol·kg^-1,与未包覆SiO2的纳米CaCO₃相比,分别提高11%、50%,同时在第5次循环快反应段吸附速率较纳米CaCO₃提高10%。与纳米CaCO₃相比,包硅后的吸附剂具有较高的吸附容量和循环吸附率,循环稳定性较好。     

沉淀法SiO2包覆纳米CaCO3吸附剂性能

以CO₂为沉淀剂,Na₂SiO₃为硅源,制备了SiO₂包覆纳米CaCO₃吸附剂。TEM测试证实纳米CaCO₃表面包覆一层SiO₂膜, 用SEM & EDX 测试5个包硅样品Si含量为0.67%～4.93%。采用TGA考察吸附剂的分解温度及600℃、20% CO₂条件下的吸附性能。结果表明：采用CO₂沉淀法包覆SiO₂后,与未包硅的纳米CaCO₃相比,分解温度降低9～42℃。纳米SiO₂/CaCO₃吸附剂的循环吸附率、吸附容量、吸附速率均随Si含量的减小先增加后降低。Si含量为1.05%的纳米SiO₂/CaCO₃吸附剂显示最佳吸附性能,第1、5次循环吸附容量分别为8.9、6.0 mol·kg^-1,与未包覆SiO2的纳米CaCO₃相比,分别提高11%、50%,同时在第5次循环快反应段吸附速率较纳米CaCO₃提高10%。与纳米CaCO₃相比,包硅后的吸附剂具有较高的吸附容量和循环吸附率,循环稳定性较好。     

α-纤维素膜气体分离性能

制备了α-纤维素膜并对其气体分离性能进行了研究.测定了水溶胀下，CO₂、H₂、CH₄、N₂、O₂等气体在α-纤维素膜内的气体渗透速率.通过比较研究醋酸纤维素膜、苯甲酰化纤维素膜和聚砜膜在干态和湿态下的气体渗透性能，揭示了水对α-纤维素膜气体渗透性能的作用规律.     

原位漫反射红外光谱研究NO和NH3在CuO/γ-Al2O3催化剂上的吸附行为

利用原位漫反射红外光谱法在线研究NH₃和NO在CuO/γ-Al₂O₃催化剂表面吸附和氧化的反应过程。NH₃不仅能被吸附在L酸位,也能被吸附在B酸位。NH3氧化脱氢形成NH₂物种是反应的中间步骤。NO和NO₂以多种形态吸附在催化剂表面。O₂存在条件下有利于吸附的NO物种被氧化成高价的NO₂。暂态实验中,吸附NH₃饱和的催化剂载体通入NO和O₂后,共价吸附的NH₃首先消失,而NH⁺₄没有参加反应。吸附NO饱和的催化剂载体通入NH₃和O₂后,吸附态NO特征峰基本没有变化。选择性催化还原反应发生在吸附态NH₃和气态NO之间,吸附态的NO及其氧化生成的亚硝基和硝基物种不参与SCR反应。     

原位漫反射红外光谱研究NO和NH3在CuO/γ-Al2O3催化剂上的吸附行为

利用原位漫反射红外光谱法在线研究NH₃和NO在CuO/γ-Al₂O₃催化剂表面吸附和氧化的反应过程。NH₃不仅能被吸附在L酸位,也能被吸附在B酸位。NH3氧化脱氢形成NH₂物种是反应的中间步骤。NO和NO₂以多种形态吸附在催化剂表面。O₂存在条件下有利于吸附的NO物种被氧化成高价的NO₂。暂态实验中,吸附NH₃饱和的催化剂载体通入NO和O₂后,共价吸附的NH₃首先消失,而NH⁺₄没有参加反应。吸附NO饱和的催化剂载体通入NH₃和O₂后,吸附态NO特征峰基本没有变化。选择性催化还原反应发生在吸附态NH₃和气态NO之间,吸附态的NO及其氧化生成的亚硝基和硝基物种不参与SCR反应。     

负载型K2CO3/Al2O3二氧化碳吸收剂的碳酸化反应特性

The carbonation characteristics of K₂CO₃/Al₂O₃ supported sorbent for CO₂ capture was investigated with thermogravimetric apparatus（TGA）,X-ray diffraction（XRD）,scanning electron microscopy analysis（SEM）and N₂ adsorption.The results showed that the carbonation rate of K₂CO₃ before being loaded on Al₂O₃ was slow.However,the K₂CO₃/Al₂O₃ upported sorbent showed excellent carbonation performance.The difference in carbonation behavior between K₂CO₃ nd K₂CO₃/Al₂O₃ supported sorbent was analyzed from the microscopic view.The analytical reagent K₂CO₃ sample was of monoclinic crystal structure and could react quickly with H₂O in the experimental carbonation environment to produce K₂CO₃&#8226;1.5H₂O,which was unfavorable to carbonation reaction.When K₂CO₃was loaded on Al₂O₃,the surface area and porosity of the sorbent was improved greatly.So the carbonation properties of the K₂CO₃/Al₂O₃ supported sorbent was also improved.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

负载型钾基CO2吸收剂的结构表征和碳酸化反应特性

The structure identification and carbonation characteristics of several potassium-based supported sorbents for CO₂ capture were investigated with TGA,XRD,XRF,SEM and N₂ adsorption method.Potassium-based sorbents were prepared by impregnation with potassium carbonate on supports,such as cocoanut activated charcoal（AC1）,coal active carbon（AC2）,silica gel（SG）and diatomite（DT）using the iso-volume impregnation method.The results showed that the K₂CO₃ loading amounts of AC1,AC2,SG and DT were 24.1%,22.5%,21.7% and 19.1% respectively.The surface area and pore volume of K₂CO₃/AC1 and K₂CO₃/AC2 were larger than others.In contrast,those of K₂CO₃/DT were small.For K₂CO₃/SG,pore volume was large but surface area was small.K₂CO₃/AC1 and K₂CO₃/AC2 showed excellent carbonation capacity.However,the carbonation capacities of K₂CO₃/SG and K₂CO₃/DT were low.The difference in carbonation capacity of those sorbents were attributed to the difference in pore structure,leading to different supported sorbents.     

Experimental study of ash formation during pulverized coal combustion in O2/CO2 mixtures

The present paper was addressed to mineral transformations and ash formation during O₂/CO₂ combustion of pulverized coal. Four Chinese thermal coals were burned in a drop tube furnace to generate ashes under various combustion conditions. The ash samples were characterized with XRD analysis and ⁵⁷Fe Mössbauer spectroscopy. The impacts of O₂/CO₂ combustion on mineral transformation and ash formation were explored through comparisons between O₂/CO₂ combustion and O₂/N₂ combustion. It was found that, O₂/CO₂ combustion did not significantly change the mineral phases formed in the residue ashes, but did affect the relative amounts of the mineral phases. The differences observed in the ashes formed in two atmospheres were attributed to the impact of the gas atmosphere on the combustion temperatures of coal char particles, which consequently influenced the ash formation behaviors of included minerals.     

In situ diagnostics of Victorian brown coal combustion in O2/N2 and O2/CO2 mixtures in drop-tube furnace

Experimental investigation of the combustion of an air-dried Victorian brown coal in O₂/N₂ and O₂/CO₂ mixtures was conducted in a lab-scale drop-tube furnace (DTF). In situ diagnostics of coal burning transient phenomena were carried out with the use of high-speed camera and two-colour pyrometer for photographic observation and particle temperature measurement, respectively. The results indicate that the use of CO₂ in place of N₂ affected brown coal combustion behaviour through both its physical influence and chemical interaction with char. Distinct changes in coal pyrolysis behaviour, ignition extent, and the temperatures of volatile flame and burning char particles were observed. The large specific heat capacity of CO₂ relative to N₂ is the principal factor affecting brown coal combustion, which greatly quenched the ignition of individual coal particles. As a result, a high O₂ fraction of at least 30% in CO₂ is required to match air. Moreover, due to the accumulation of unburnt volatiles in the coal particle vicinity, coal ignition in O₂/CO₂ occurred as a form of volatile cloud rather than individual particles that occurred in air. The temperatures of volatile flame and char particles were reduced by CO₂ quenching throughout coal oxidation. Nevertheless, this negative factor was greatly offset by char-CO₂ gasification reaction which even occurred rapidly during coal pyrolysis. Up to 25% of the nascent char may undergo gasification to yield extra CO to improve the reactivity of local fuel/O₂ mixture. The subsequent homogeneous oxidation of CO released extra heat for the oxidation of both volatiles and char. As a result, the optical intensity of volatile flame in ∼27% O₂ in CO₂ was raised to a level twice that in air at the furnace temperature of 1273 K. Similar temperatures were achieved for burning char particles in 27% O₂/73% CO₂ and air. As this O₂/CO₂ ratio is lower than that for bituminous coal, 30-35%, a low consumption of O₂ is desirable for the oxy-firing of Victorian brown coal. Nevertheless, the distinct emission of volatile cloud and formation of strong reducing gas environment on char surface may affect radiative heat transfer and ash formation, which should be cautioned during the oxy-fuel combustion of Victorian brown coal.     

钾基CO2吸收剂的碳酸化反应特性

对钾基CO₂吸收剂的碳酸化反应机理进行研究。利用热重分析、XRD、扫描电镜和氮吸附仪进行试验。结果表明：分析纯碳酸钾的组分为K₂CO₃·1.5H₂O,碳酸化反应速率缓慢;先将分析纯碳酸钾样品脱除结晶水后再进行碳酸化反应时,K₂CO₃与气氛中的水蒸气迅速生成K₂CO₃·1.5H₂O,不利于碳酸化反应的进行;由KHCO₃分解产生的K₂CO₃却表现出优越的碳酸化反应性能,20 min内转化率高达85%以上,经过多次循环试验后吸收剂仍保持很高的活性。从微观角度分析了两种改性钾基CO₂吸收剂碳酸化反应机理差异的原因,通过拟合计算得到了这3种钾基吸收剂的碳酸化反应速率常数,为干法K₂CO₃/KHCO₃循环脱除CO₂的研究提供了一定的基础数据。     

Fe2O3对高变质程度脱灰煤热解反应性与半焦结构的影响

利用热天平研究了共混合法负载Fe₂O₃高变质程度脱灰煤的热解反应性，结果表明煤粉负载Fe₂O₃后热解反应性高于无负载的热解反应性。负载Fe₂O₃煤样在程序升温加热的马弗炉中制备出半焦，利用FTIR、XRD和RAMAN 等分析了半焦结构。由TG和FTIR可知，负载Fe₂O₃煤样热解时，热解转化率增加，热解后自由基增加。由XRD可知，Fe₂O₃没有使得煤样半焦的002峰衍射角发生明显变化，但使L_a和L_c参数明显降低，说明半焦的微晶结构石墨化程度降低。另外，在XRD分析谱图中发现部分Fe₂O₃被还原成FeO。由RAMAN可知，Fe₂O₃使半焦的G峰峰面积降低，D峰峰面积增加，说明半焦的有机结构有序化程度降低。     

CO2载体CaO循环煅烧/碳酸化反应的分形特征

捕捉煤燃烧释放出的CO₂时,作为CO₂载体的CaO微观结构特性对其循环碳酸化性能具有显著影响。采用分形维数作为表征CaO微观结构的特征参数,研究在循环煅烧/碳酸化反应过程中CaO的分形特征及其对CO₂捕捉性能的影响规律。结果表明,随着循环次数的增加CaO分形维数逐渐下降,CaO孔道也由粗糙和不规则变得越来越平滑和有规则性。煅烧温度升高则CaO分形维数下降。分形维数较大的CaO具有较高的碳酸化速率。在碳酸化过程的前10 min内CaO的分形维数迅速减小,此后随时间变化缓慢。在分形维数D≤2.61的实验范围内,CaO分形维数与其循环碳酸化转化率呈线性正相关;当D＞2.61时,可能存在临界分形维数D_cr,当D＞D_cr时随着分形维数的进一步增大CaO转化率反而减小。