Interdiffusion and Association Phenomena in the System NiO-Al2O3

The rate of formation of NiAl₂O₄ by reaction between single crystals of NiO and Al₂O₃ can be described by k = 1.1 × 10⁴ exp (−108,000 ± 5,000/ RT ) cm²/s. In NiO the behavior of D as a function of concentration supports the Lidiard theory of diffusion by impurity-vacancy pairs. A good fit of the theory to the experimental results was obtained by assuming that Al³⁺ ions diffuse as [Al_Ni· V_Ni]'pairs. The diffusion coefficient of pairs, D_p , obeys the equation 6.6 × 10⁻² exp (−54,000 ± 3,000/ RT ) cm²/s. The free energy of association for pairs was calculated to range from 6.5 kcal/mol at 1789°C to 9.0 kcal/mol at 1540°C. The interdiffusion coefficients in the spinel showed a constant small increase with increasing concentration of Al³⁺ dissolved in the spinel.     

Deviation from Stoichiometry in Cr2O3 at High Oxygen Partial Pressures

The deviation from stoichiometry, δ, in Cr₂−δO₃ was measured by a tensivolumetric method in the high pO₂ range of ≊10⁴ to 10⁴ Pa at 1100°C. The value of δ, or chromium vacancy concentration, was≊9×10⁻⁵ mol/mol Cr₂O₃ in air for Cr₂O₃ with 99.999% purity. The chemical diffusion coefficient, DT, determined from equilibration data was ≊4.6× cm²·s⁻¹ at 1100°C for pO₂= 2.2 ×10¹ Pa. The self-diffusion coefficient of Cr ions was calculated from and δ and found to be≊1.6×10-17 cm²-s⁻¹, in good agreement with recently measured values.     

Electrical Conduction in Single-Crystal and Polycrystalline Al2O3 at High Temperatures

The electrical conductivity and ion/electron transference numbers in Al₃O₃ were determined in a sample configuration designed to eliminate influences of surface and gas-phase conduction on the bulk behavior. With decreasing O₂ partial pressure over single-crystal Al₂O₃ at 1000° to 1650°C, the conductivity decreased, then remained constant, and finally increased when strongly reducing atmospheres were attained. The intermediate flat region became dominant at the lower temperatures. The emf measurements showed predominantly ionic conduction in the flat region; the electronic conduction state is exhibited in the branches of both ends. In pure O₂ (1 atm) the conductivity above 1400°C was σ≃3×10³ exp (–80 kcal/ RT ) Ω⁻¹ cm⁻¹, which corresponds to electronic conductivity. Below 1400°C, the activation energy was <57 kcal, corresponding to an extrinsic ionic condition. Polycrystalline samples of both undoped hot-pressed Al₂O₃ and MgO-doped Al₂O₃ showed significantly higher conductivity because of additional electronic conduction in the grain boundaries. The gas-phase conduction above 1200°C increased drastically with decreasing O₂ partial pressure (below 10⁻¹⁰ atm).     

Thermal Expansion of the Low-Temperature Form of BaB2O4

Thermal expansion of the low-temperature form of BaB₂O₄ (β-BaB₂O₄) crystal has been measured along the principal crystallographic directions over a temperature range of 9° to 874°C by means of high-temperature X-ray powder diffraction. This crystal belongs to the trigonal system and exhibits strongly anisotropic thermal expansions. The expansion along the c axis is from 12.720 to 13.214 Å (1.2720 to 1.3214 nm), whereas it is from 12.531 to 12.578 Å (1.2531 to 1.2578 nm) along the a axis. The expansions are nonlinear. The coefficients A, B , and C in the expansion formula L _t = L ₀(1 + At + Bt ²+ Ct ³) are given as follows: a axis, A = 1.535 × 10⁻⁷, B = 6.047 × 10⁻⁹, C = -1.261 × 10⁻¹²; c axis, A = 3.256 × 10⁻⁵, B = 1.341 × 10⁻⁸, C = -1.954 × 10⁻¹²; and cell volume V, A = 3.107 × 10⁻⁵, B = 3.406 × 10⁻⁸, C = -1.197 × 10⁻¹¹. Based on α _t = (d L _t /d t )/ L ₀, the thermal expansion coefficients are also given as a function of temperature for the crystallographic axes a , c , and cell volume V.     

Concurrent Measurement of Volume, Grain-Boundary, and Surface Diffusion Coefficients in the System NiO-Al2O3

Surface, grain-boundary, and volume inter diffusion coefficients for the NiO-Al₂O₃ system were measured concurrently by using a diffusion couple consisting of an A1₂O₃ bicrystal and an NiO single crystal. The A1₂O₃ bicrystals having various tilt angles were fabricated by firing 2 single crystals to be joined in an H₂ atmosphere at 1800°C for 30 h. Diffusion profiles over the surface, along the grain boundary, and in the bulk of the bicrystal were determined with an electron probe microanalyzer. Mathematical analysis of the diffusion profiles gives D _s = 7.41×10^-2 exp (-35,200/ RT ), D _gb = 2.14×10^-1 exp (-63,100/ RT ) (tilt angle =30°), and D _v = 1.26×10⁴ exp (-104,000/ RT ). The grain-boundary diffusion coefficient increases with the mismatch at the boundary.     

Annealing of Irradiation-Induced Thermal Conductivity Changes in ThO2-1.3 wt% UO2

The thermal conductivities of sintered pellets of ThO₂-1.3 wt% U0₂ were measured at 60°C before and after irradiation. The irradiation temperature was below 156°C, and the exposures varied from 3.1 × 10¹⁴ to 4.7 × lo^L7 fissions/cm³. Each fission fragment damaged a region of 2.2 × 10^-16 cm³ with the reduction in conductivity saturating by about 10¹⁷ fissions/cm³. Samples having exposures from 10¹⁵ to 10¹⁶ fissions/cm³ were annealed isothermally at 651 °C or isochronally from 300° to 1200° C to study the annealing of damage. Most of the annealing occurred between 500° and 900°C. The width of this interval plus the slow isothermal annealing suggest that the damage is annealed by a number of single order processes with a spectrum of activation energies from 1.8 to 3.9 eV or, less probably, by a high order process with an activation energy of 3.55 ± 0.4 eV.     

Crystallization and Properties of Fe2O3—CaO—SiO2 Glasses

Nucleation and crystal growth rates and properties were studied in a two-stage heat treatment process for Fe₂O₃-CaO-SiO₂ glasses. Glass transition (T_g) and crystallization temperatures (T _c ) for the glasses lay between about 612.0° and 710.0°C, and 858.5° and 905.0°C, respectively, and magnetite was the main crystal phase. For a glass of 40Fe₂O₃. 20CaO·40SiO₂ (in wt%) the maximum nucleation rate was (68.6 ± 7) × 10⁶/mm³·s at 700°C, and the maximum crystal growth rate was 9.0 nm/min^1/2 at 1000°C. The mean crystal size of the magnetite increased from 30 to 140 nm with variation of nucleation and crystal growth conditions. The glass showed the maxima in saturation magnetization and coercive force, 212.1 × Wb/m² and 30.8 × 10³ A/m, when heat-treated for 4 h at 1000°C and 1050°C, respectively. The variation of the saturation magnetization could be quantitatively interpreted well in terms of the volume fraction of the magnetite, whereas that of the coercive forces could be explained only qualitatively in terms of the particle size of the magnetite. Hysteresis losses showed the maximum value of 1493 W/m³ when heat-treated at 1000°C for 4 h prenucleated at 700°C for 60 min, and increased linearly with increasing heat treatment time under a magnetic field up to 800 × 10³ A/m.     

Effect of Neutron Irradiation on Knoop Microhardness Anisotropy in MgO·3Al2O3 Single Crystals

MgO·3Al₂O₃ single crystals were irradiated with neutron fluences of 8.3 × 10²² n/m² at 100°C and 2.4 × 10²⁴ n/m² at 470°C ( E > 1.0 MeV) in the Japan Materials Testing Reactor. The Knoop microhardness of several orientations on the (100) plane of both the irradiated and unirradiated crystals were measured with different indentation loads. The change in hardness profile of the crystals was almost the same after the two irradiation conditions. The hardness increased by 4–15% because of the irradiations depending on the crystallographic orientation, the larger change being observed at orientations between the (001) and (011) directions. While both the {111}     and {110}     slip systems are simultaneously active in the unirradiated MgO·3Al₂O₃, the {111}     system may be the dominant slip system in the neutron-irradiated crystals. It is concluded that the restriction of the {110}     slip system is caused by irradiation-induced interstitial ions.     

Tribological Behavior of Ti2SC at Ambient and Elevated Temperatures

The tribological properties of Ti₂SC were investigated at ambient temperatures and 550°C against Ni-based superalloys Inconel 718 (Inc718) and alumina (Al₂O₃) counterparts. The tests were performed using a tab-on-disk method at 1 m/s and 3N (≈0.08 MPa). At room temperature, against the superalloy, the coefficient of friction, μ, was ∼0.6, and at ∼8 × 10⁻⁴ mm³·(N·m)⁻¹ the specific wear rate (SWRs), was high. However, against Al₂O₃, at ∼5 × 10⁻⁵ mm³·(N·m)⁻¹ and ∼0.3, the SWRs and μ were significantly lower, which was presumably related to more intensive tribo-oxidation at the contact points. At 550°C, the Ti₂SC/Inc718 and Al₂O₃ tribocouples demonstrated comparable μ's of ∼0.35–0.5 and SWRs of ∼7–8 × 10⁻⁵ mm³·(N·m)⁻¹. At 550°C, all tribosurfaces were covered by X-ray amorphous oxide tribofilms. At present, Ti₂SC is the only member of a family of the layered ternary carbides and nitrides (MAX phases) that can be used as a tribo-partner against Al₂O₃ in the wide temperature range from ambient to 550°C.     

Thermal Diffusivity of Be4B, Be2B, and BeB6

The thermal diffusivities of polycrystalline Be₄B, Be₂B, and BeB₆ were measured by the flash method. Generally, the thermal diffusivities at a given temperature decrease with increasing boron content. The thermal diffusivities of Be₄B, Be₂B, and BeB₆ varied from 0.13 to 0.072 to 0.031 cm²/s, respectively, at 200°C and from 0.068 to 0.038 to 0.007 cm²/s at 1000°C. Heat transport in BeB₆ is expected to occur almost entirely by phonon conduction, whereas electronic conduction probably plays a major role in Be₄B and Be₂B. Analytical expressions for the thermal diffusivities (α) of Be₄B and Be₂B at 200° to 1000°C and of BeB₆ at 25° to 1500°C are: α(Be₄B)=1/(5.83+9.05×10 3 T ), α(Be₂B)=1/(10.92+1.40×10 2 T ), and α(BeB₆)=5.60×10 4+5.72/ T +77.3/T²-4.09×10⁴/T³ cm²/s.     

Thermal Expansion of 12CaO°7Al2O3

Literature data for the 12CaO°7Al₂O₃ phase show certain discrepancies in the structure, thermal stability, and mean linear thermal expansion obtained by different techniques. Phase-pure, cubic, polycrystallin I2CaO°7Al₂O₃ was synthesized by annealing a stoichiometric melt in air. Infrared spectrophotometry indicated stabilization by moisture. Differential thermal analysis and thermogravimetric analysis showed the cubic phase to be stable up to at least 1200° C. High-temperature X-ray diffraction analysis of a polycrystalline sample and dilatometric measurement of sintered pellets indicated a linear thermal expansion of 41 × 10^-7 to 43X10^-7/°C in the temperature range 200° to 800°C.     

In Situ Reaction Synthesis, Electrical and Thermal, and Mechanical Properties of Nb4AlC3

In this work, a bulk Nb₄AlC₃ ceramic was prepared by an in situ reaction/hot pressing method using Nb, Al, and C as the starting materials. The reaction path, microstructure, physical, and mechanical properties of Nb₄AlC₃ were systematically investigated. The thermal expansion coefficient was determined as 7.2 × 10⁻⁶ K⁻¹ in the temperature range of 200°–1100°C. The thermal conductivity of Nb₄AlC₃ increased from 13.5 W·(m·K)⁻¹ at room temperature to 21.2 W·(m·K)⁻¹ at 1227°C, and the electrical conductivity decreased from 3.35 × 10⁶ to 1.13 × 10⁶Ω⁻¹·m⁻¹ in a temperature range of 5–300 K. Nb₄AlC₃ possessed a low hardness of 2.6 GPa, high flexural strength of 346 MPa, and high fracture toughness of 7.1 MPa·m^1/2. Most significantly, Nb₄AlC₃ could retain high modulus and strength up to very high temperatures. The Young's modulus at 1580°C was 241 GPa (79% of that at room temperature), and the flexural strength could retain the ambient strength value without any degradation up to the maximum measured temperature of 1400°C.     

Interdiffusion in the System MgO-MgAl2O4

Interdiffusion coefficients in single-crystal MgO were determined using an MgO-MgAl₂O₄ diffusion couple. For a concentration of 1 mol% Al₂O₃ in MgO, the interdiffusion coefficient can be expressed as D =2.0±0.2 exp (−76,000±3,000/ RT ) for the MgO-MgAl₂O₄ couple. This relation compares well with previous measurements in the MgO-Al₂O₃ system. The interdiffusion coefficients, which increased with the mol fraction of cation vacancies, were in the range of 10⁻⁸ to 10⁻¹⁰ cm²s⁻¹ for the concentrations and temperatures studied. Diffusion was enhanced below 1640°C if powdered MgAl₂O₄ was used. Self-diffusion coefficients for Al³⁺ ions in MgO were calculated; Al³⁺ diffuses faster than Cr³⁺ in MgO.     

Sodium Diffusion in SiO2 Glass

Diffusion of the radioactive tracer ²²Na in a commercial SiO₂ glass was investigated from 170° to 1000°C. The temperature dependence curve had discontinuities at about 573° and 250°C. The resulting Arrhenius equations are D = 3.44 × 10² exp(-21.1 kcal/RT) cm²/sec between 1000° and 573°C, D = 0.398 exp(-25.8 kcal/RT) cm²/sec between 573° and 250°C, and D = 2.13 exp(-28.3 kcal/RT) cm²/sec between 250° and 170°C. The two anomalies are discussed in terms of "quartz-like" and "cristobalite-like" precrystalline elements in the structure of the glass. Comparison of the Na diffusion in SiO, glass with that in soda-silica and soda-lime-silica glasses shows that SiO₂ glass occupies a boundary position with respect to these systems. A possible diffusion mechanism is discussed.     

Microcellular Al2O3 Ceramics from Wood for Filter Applications

Microcellular biomorphous Al₂O₃ was produced by Al-vapor infiltration in pyrolyzed rattan and pine wood-derived biocarbon preforms. At 1600°C the biocarbon preforms reacted with gaseous aluminum to form Al₄C₃. After oxidation in air at temperatures between 1550° and 1650°C, for 3 h, the biocarbon preforms were fully converted into α-Al₂O₃. Owing to the high anisotropy of biomorphous Al₂O₃, the compressive strength behavior was strongly dependent on the loading direction. The compressive strength of the specimens (0.1–11 MPa) is strongly dependent on their overall porosity and their behavior could be explained using the Gibson–Ashby model. The Darcian permeability ( k ₁), as well as the non-Darcian permeability ( k ₂), increased with an increase of the total porosity. The Darcian permeability of biomorphous Al₂O₃ was found to be in the range of 1–8 × 10⁻⁹ m², which is in the order of magnitude of gas filters, and, therefore, suitable for several technological applications.     

Thermal Expansion of Polycrystalline Ti3SiC2 in the 25°–1400°C Temperature Range

We measured the volume thermal expansion of Ti₃SiC₂ from 25° to 1400°C using high-temperature X-ray diffraction using a resistive heated cell. A piece of molybdenum foil with a 250 μm hole contained the sample material (Ti₃SiC₂+Pt). Thermal expansion of the polycrystalline sample was measured under a constant argon flow to prevent oxidation of Ti₃SiC₂ and the molybdenum heater. From the lattice parameters of platinum (internal standard), we calculated the temperature by using thermal expansion data published in the literature. The molar volume change of Ti₃SiC₂ as a function of temperature in °C is given by: V _M (cm³/mol)=43.20 (2)+9.0 (5) × 10⁻⁴ T +1.8(4) × 10⁻⁷ T ². The temperature variation of the volumetric thermal expansion coefficient is given by: α_v (°C⁻¹)=2.095 (1) × 10⁻⁵+7.700 (1) × 10⁻⁹ T . Furthermore, the results indicate that the thermal expansion anisotropy of Ti₃SiC₂ is quite mild in accordance with previous work.     

Thermal Expansion of Y2SiO5 Single Crystals

The thermal expansion of Y₂SiO₅ crystals has been measured for the principal crystallographic directions and two orthogonal directions in the (010) plane in the temperature range 25° to 200°C. This monoclinic crystal has strongly anisotropic expansions with coefficients which range from 0.6 × 10⁻⁶/°C for [100] to 11.4 × 10⁻⁶/°C for [001]. Third-order polynomials have been calculated from the expansion curves. Data for the β angle and cell volume as a function of temperature are also given. The thermal expansion of Y₂SiO₅ crystals is not affected by doping with 5% Tb.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Cation Self-Diffusion in Cr2O3

Self-diffusion of ⁵¹Cr was measured both parallel to and perpendicular to the c axis in single crystals of Cr₂O₃ as a function of oxygen partial pressure at 1490° and 1570°C. The oxygen-partial-pressure dependence of the diffusivity indicates that cation self-diffusion occurs by a vacancy mechanism. The values of the self diffusion coefficients determined in this experiment are about 10⁴ times smaller than those previously reported in this temperature range .     

Eletrical Properties of Glasses in the System PbO-Al2O3-B2O3-SiO2

Glasses in the system Pb0–Al₂O₃-B₂O₃-SiO₂ are chemically stable over a wide composition range and have very desirable electrical characteristics such as high electrical resistivities and activation energies for conduction. Variations in these electrical properties were studied as a function of composition changes within the system, the object being to identify the role of the constituent oxides in achieving the highest activation energy and resistivity values consistent with moderate preparation temperatures. Measurements were made in the temperature range 25° to 400°C on carefully prepared glass disks in which the individual oxide components or different oxide ratios such as PbO/SiO₂, Al₂O₃/SiO₂, and B_sO₃/SiO₁ were systematically varied. The activation energy and resistivity values obtained ranged from 1.2 to 1.6 ev and 10° to 10¹⁴ ohm-cm, with dielectric constants ranging from 9 to 19 and densities from 4.30 to 4.50 g/cmY. Indications were that, for the composition range studied, the behavior manifested was basically that of the binary PbO-SO₂ glass with additions of Al₂O₃ or B₂O₃, even in small concentrations, sharply increasing the activation energy for conduction while lowering the density.