Electrically conductive silicon carbide with the addition of TiNbC

The work deals with the preparation of dense SiC based ceramics with high electrical conductivity. SiC samples with different content of conductive TiNbSiCO based phase were hot pressed at 1820 °C for 1 h in Ar atmosphere under mechanical pressure of 30 MPa. The conductive phase is a mixture of 50 wt% TiNbC (molar ratio of Ti/NbC is 1:1.8) and 50 wt% eutectic composition of Y₂O₃SiO₂. Composite with 30% of conductive TiNbSiCO phase showed the highest electrical conductivity 28.4 S mm^?1, while the good mechanical properties of SiC matrix were preserved (fracture toughness K_IC = 5.4 MPa m^1/2 and Vickers hardness 17.8 GPa).The obtained results show that the developed additive system is suitable for the preparation of SiC-based composite with sufficient electrical conductivity for electric discharge machining.     

Low temperature sintering and microwave dielectric properties of (Mg3 − xZnx)(VO4)2 ceramics

This paper describes the effects of Zn substitution for Mg on the microwave dielectric properties of (Mg_3 − xZn_x)(VO₄)₂ ceramics. As for the XRPD patterns of (Mg_3 − xZn_x)(VO₄)₂ ceramics sintered at the sintering temperature of 750 °C, no secondary phase was detected over the whole composition range. However, in the case of the sample sintered at 850 °C, the Zn₄V₂O₉ and Zn₂V₂O₇ compounds were identified by using XRPD; this result was attributed to the decomposition of Zn₃(VO₄)₂ phase. From crystal structure analysis, it was found that the atomic distances of M(1)O (M = Mg and Zn) and M(2)O in MO₆ octahedra increased, though that of VO in VO₄ tetrahedron decreased. Moreover, the slight tilting of M(2)O₆ octahedron was observed by the Zn substitution. As for the covalency of cation–oxygen bond, the covalency of MO bond in M(1)O₆ and M(2)O₆ octahedra decreased because of the increase in the atomic distance of MO, whereas that of VO increased with increasing the Zn addition. However, as a result, the slight decrease in the covalency of cation–oxygen bond was recognized because the variation in the covalency of MO bond is predominant in this crystal structure. The dielectric constants of the samples range from 4.4 to 11.1. The decrease in the covalency may be related to the difference in the dielectric constant of each composition. The maximum Q · f value of bulk densities is effected by varying the chemical composition of (Mg_3 − xZn_x)(VO₄)₂ ceramics and it shifts toward lower sintering temperature with an increase in x within the temperature region of 800–1050 °C. The temperature coefficient of resonant frequency (τ_f) of the samples decreased with increasing of Zn, and then a variation in τ_f value was attributed to the tilting of M(2)O₆ octahedron caused by Zn substitution for Mg.     

Measurement of the hydroxyl radical formation from H2O2, NO3−, and Fe(III) using a continuous flow injection analysis

Production of hydroxyl radical (OH) is of significant concern in engineered and natural environment. A simple in situ method was developed to measure OH formation in UV/H₂O₂, UV/Fe(III), and UV/NO₃^? systems using trapping of OH by benzoic acid (BA) and measuring fluorescence signals from hydroxylated products of BA. Method development included characterization of OH trapping mechanism and measurement of quantum yields (Φ_OH) for OH. The distribution of OHBA isomers was in the order of o-OHBA > p-OHBA > m-OHBA, although it changed with the H₂O₂ concentration and light intensity. This supports that OH attacks dominantly on the benzene rings. The quantum yields for OH formation in the UV/H₂O₂ process were 1.02 and 0.59 at 254 and 313 nm, which were in good agreement with the literature values, confirming that the method is suitable for the measurement of OH production from UV/H₂O₂ processes. Using the continuous flow method developed, quantum yields for OH in UV/H₂O₂, UV/Fe(III), and UV/NO₃^? systems were measured varying the initial concentration of OH precursors. The Φ_OH values increased with increasing concentrations of H₂O₂, Fe(III), and NO₃^? and approached constant values as the concentration increased. The Φ_OH values were 0.009 for H₂O₂ at 365 nm, showing that OH production is not negligible at such high wavelength. The Φ_OH values during the photolysis of Fe(OH)²⁺ (pH 3.0) and Fe(OH)₂⁺ (pH 6.0) at 254 nm were 0.34 and 0.037, respectively. The Φ_OH values for NO₃^? approached a constant value of 0.045 at 254 nm at the initial concentration of 10 mM.     

Thermally stable pseudo-third-generation Grubbs ruthenium catalysts with pyridine–phosphinimine ligand

The ligand precursors 2-(R₃PN)CH₂Py (R = Ph(1a), Cy(2a)) were prepared from reaction of pyridine azide with various phosphine ligands. Reaction of 1a or 2a with RuCl₂(CHPh)(Py)₂(H₂IMes) (Py = pyridine) afforded the ruthenium alkylidene complex RuCl₂(CHPh)(PyCH₂(NPR₃))(H₂IMes) (R = Ph(1), Cy(2)). Both catalysts showed good thermal stability and latent behavior toward RCM and ROMP reactions.     

Activity of Mo(II) allylic complexes supported in MCM-41 as oxidation catalysts precursors

[Mo(η³-C₃H₅)X(CO)₂(NCCH₃)₂] (X = Br, 1a; X = Cl, 1b) complexes reacted with the bidentate ligand RNC(Ph)–C(Ph)NR, R = (CH₂)₂CH₃ (DAB, 2) affording [Mo(η³-C₃H₅)X(CO)₂(DAB)] (X = Br, 4a; X = Cl, 4b), which were characterized by elemental analysis, FTIR and ¹H and ¹³C NMR spectroscopy. The modified silylated ligand RNC(Ph)C(Ph)NR, R = (CH₂)₃Si(OCH₂CH₃)₃ (DAB–Si, 3), was used to immobilize the two complexes in MCM-41 (MCM) mesoporous silica. The new materials were characterized by powder X-ray diffraction, N₂ adsorption analysis, FTIR and ²⁹Si and ¹³C CPMAS solid state NMR spectroscopy. Both the materials and the complexes were tested in the oxidation of cyclooctene and styrene and behaved as active catalyst precursors for cyclooctene and styrene epoxidation with TBHP (t-butylhydroperoxide), leading selectively to epoxides with high conversions and TOFs. Although the homogeneous systems reach 100% conversion of cyclooctene and slightly less for styrene, the loss of catalytic activity in the heterogeneous systems is small, with a 98% conversion of styrene achieved by the chloride containing material.     

Degradation of mechanical and electrical properties after long-term oxidation and corrosion of non-oxide structural ceramic composites

This work summarizes the results related to the influence of the starting composition and of microstructure on properties degradation, due to oxidation and corrosion, relatively to the following structural ceramics: Si₃N₄TiN, Si₃N₄MoSi₂, AlNSiCMoSi₂, AlNSiC.The effects of: (i) long-term oxidation in air (100 h), in the temperature range 600–1500 °C and (ii) of long-term corrosion (400 h) in acid or basic aqueous solution at RT, 40 and 70 °C, on the electrical resistivity and mechanical strength of the composites are analysed and compared. The degradation of the properties are related to the characteristics of the surface and sub-surface damage after oxidation and corrosion treatments.     

Etherification reactions of propargylic alcohols catalyzed by a cationic ruthenium allenylidene complex

The cationic ruthenium allenylidene complex R_RuR_ax −[Ru(indenyl)L(PPh₃)CCCPh₂]⁺PF₆ catalyzes the etherification of secondary and tertiary propargylic alcohols in a formal nucleophilic substitution reaction utilizing primary and secondary alcohols as the nucleophiles. At a catalyst loading of only 1.1 mol%, the corresponding propargylic ether products were obtained in 9 to 73% isolated yields (18 h reaction time at 100 °C); no further additives are required. The reaction exhibits an induction period; as shown by a control reaction, the high reaction temperature may chemically change the allenylidene complex to be employed as the catalyst but does not lead to catalyst deactivation.     

Synthesis,X-ray structure,spectroscopic properties,and theoretical investigations of dinuclear imidazole molybdenum(VI) complex with long MoO bands

One new dinuclear multioxomolybdenum(VI) complex containing long MoO bands with imidazole, [Mo₂O₆(imi)₄] (1) (imi = imidazole), has been prepared and characterized, and the geometric structure, electronic structure and spectroscopic properties, investigated experimentally and theoretically. The rarely observed long MoO bonds in 1 (ca. 0.15 Å longer than documents previously) are analysed by orbital structure analysis. The electronic origins of the optical transitions are also mainly related to the MoO groups with ligand-to-metal charge transfer (LMCT) nature (P_terminal-oxo → d_Mo).     

Extended X-ray absorption fine structure,X-ray diffraction and Raman analysis of nickel-doped Ba(Mg1/3Ta2/3)O3

Raman, X-ray diffraction and extended X-ray absorption fine structure (EXAFS) measurements of xBa(Ni_1/3Ta_2/3)O₃ + (1 − x)Ba(Mg_1/3Ta_2/3)O₃ samples with x = 0–0.03 were performed to reveal the nickel doping effect on the microwave properties. EXAFS result clearly shows that the nickel is located on the Mg lattice site. We also found that, as the nickel concentration increases, microwave dielectric constant decreases with the TaO and NiO bond distances. X-ray diffraction shows that the 1:2 ordered structure is degraded with the increasing of nickel concentration. The stretching phonon of the TaO₆ octahedra, that is A_1g(O) phonon near 800 cm⁻¹, are strongly correlated to the microwave properties of xBa(Ni_1/3Mg_2/3)O₃ + (1 − x)Ba(Mg_1/3Ta_2/3)O₃ samples. The large Raman shift and the large width of the A_1g(O) imply rigid but distorted oxygen octahedral structure, therefore, the effect of nickel doping lowers the dielectric constant and the Q × f value of Ba(Mg_1/3Ta_2/3)O₃ ceramic.     

Fabrication of polymer derived ceramic parts by selective laser curing

Polymer derived ceramic parts of complex shape were fabricated by selective laser curing (SLC). The ceramic parts were built similar to the selective laser sintering process by sequentially irradiating layers consisting of SiC loaded polysiloxane powder with a CO₂-laser beam (λ = 10.6 μm), which locally induces curing reaction of the polymer phase at moderate temperatures around 400 °C. The laser-cured bodies were converted to SiOC/SiC ceramic parts in a subsequent pyrolysis treatment at 1200 °C in argon atmosphere. The scanning speed and the power of the CO₂-laser beam were varied, leading to pronounced differences in material properties. Laser irradiating a powder mixture containing 50 vol.% polymer/50 vol.% SiC resulted in relative green densities between 38 and 60%. Relative densities decreased to 32–50% after pyrolysis due to the polymer shrinkage. A post-infiltration with liquid silicon was carried out in order to produce dense parts. While before infiltration the bending strength only attained 17 MPa as a result of both microcracks in the SiOC matrix and a pronounced porosity, an average value of 220 MPa was achieved after post-infiltrating with Si. In the case of 50 vol.% SiC content the linear shrinkage after pyrolysis was only 3%. Thus, the SLC approach can be considered as a near-net-shape forming process of ceramic components with complex geometries.     

A model study for the breaking of cyanogen out of CNx within DFT

To explain the nitrogen low rate in CVD CN_x layers, and their amorphisation, a release of gaseous species containing N was proposed. Previous modelling studies based on local density functional theory use pyrite type CN₂ as starting model to assess the release of molecular nitrogen. This model is completed here to investigate another mechanism of release of cyanogen as another gaseous species. The theoretical pyrite-like C₂N wherein C and N atoms form dumbbells in octahedral sites of a carbon face-centred sub-lattice is proposed as likely to model it. It demonstrates a good compressibility (B₀ = 272 GPa) and a mechanical instability, which supports both release of atoms and the amorphisation of layers. However, the variation of interatomic distances under strain leads to propose the formation of a radical species CN. This is enforced by the consideration of the chemical bonding and its evolution in the model with the E_COV and ELF functions. The release of nitrogen in molecular cyanogen is consequently substituted by a mechanism which implies a CN radical species, which is likely to recombinate at the CVD layers surfaces.     

The control of BN and BC bonds in BCN films synthesized using pulsed laser deposition

A novel chemical bond transformation from BN to BC was observed in BCN films synthesized using pulsed laser deposition (PLD). BCN film prepared by using green laser (λ=532 nm) induced two IR absorption at 1370 and 800 cm⁻¹. This film was dominated by amorphous carbon phase and sp² hybridized BN bonds. BCN film deposited using an ultraviolet (UV) laser (λ=266 nm ) induced an addition infrared (IR) absorption at 1250 cm⁻¹. As we deposit BCN film by deep-UV laser (λ=213 nm), the absorption at 1370 and 800 cm⁻¹ disappeared while the absorption at 1250 cm⁻¹ remained. According to X-ray photoelectron spectroscopy (XPS), BC bonds with a carbon rich composition were formed. The formation of BC bonds in BCN films was also sensitive to deposition gas pressure and substrate temperature. Reactive carbon and boron species were needed to enable BC bonds that hybridized the carbon and the BN phases. A low substrate temperature was required to avoid competition with sp² hybridized pure BN and pure carbon bonds.     

Carbothermal synthesis of β-sialon from mechanochemically activated precursors

Reaction mixtures of halloysite clay and fine carbon for carbothermal reduction and nitridation (CRN) synthesis of β-sialon were ground in a planetary ball mill under flowing nitrogen for varying periods before being converted to sialon by heating in nitrogen at 1200–1400 °C. After 4 h grinding the XRD reflections of the halloysite were destroyed and some of the octahedrally-coordinated Al was converted to four- and five-fold coordination. ²⁷Al and ²⁹Si MAS NMR gave no evidence of the formation of AlN or SiN bonds upon grinding. Upon subsequent heating in nitrogen, the ground samples show significant differences from the unground control, the intermediate compound mullite being replaced by β-sialon (z ≈ 2) a temperature at least 100 °C lower, but the formation of corundum (α-Al₂O₃) also occurs at a lower temperature and is more persistent than in the unground control. MAS NMR spectroscopy shows that the products from the ground mixtures contain relatively less AlON units and that the formation of SiC (a transient reaction intermediate) is also facilitated by grinding. The optimum grinding time for this system was found to be 12 h.     

Towards osseointegration of bioinert ceramics: Can biological agents be immobilized on alumina substrates using self-assembled monolayer technique?

Immobilization of biological agents on inert alumina surfaces could promote bone growth and improve osseointegration. We hypothesize that functional groups on alumina surfaces can be used to link biological agents as a supporting factor e.g. for cell attachment. CH₂, OH, COOH, and NH₂ groups were linked to alumina surfaces using self-assembled monolayer technique (SAM). Subsequently, bovine serum albumin (BSA) was immobilized on each functionalized surface. Contact angle, bicinchoninic acid assay and immunofluorescence were used to detect immobilized BSA. The amount of BSA linked to functionalized surfaces increased in the following order CH₂ < OH < COOH = NH₂. The greatest amount, 26.1 μg/cm² of BSA was found on both, NH₂- and COOH-terminated surfaces. Cell tests confirmed cytocompatibility of all surfaces. The highest proliferation was detected on NH₂-terminated samples. Using the model protein, the results confirmed feasibility for immobilization of biological agents to inert alumina ceramic surfaces using SAM technique.     

Direct conversion of citrus peel waste into hydroxymethylfurfural in ionic liquid by mediation of fluorinated metal catalysts

A new green technology was developed using citrus peel waste to produce hydroxymethylfurfual (HMF). FT-IR analysis of the waste showed 4 characteristic vibration modes (CH, CO, COH, and CO/COO^?), contributing to sugars. XRD and FESEM elucidated that the waste and its hydrolysate consist of highly amorphous clusters. HCl increased HMF yield by 1.4-fold. CrF₃ increased its yield by 1.7-fold. At 0.2 of the stoichiometric ratio value, HMF yield was highest. The highest HMF yield was achieved in the reaction mixture of 4 g [OMIM]Cl, 1 mL ethyl acetate, 0.1 g CrF₃, 5 mL 0.3 M HCl, and 0.5 g biomass.     

High Q dielectric resonator material with low dielectric constant for millimeter-wave applications

Al₂O₃TiO₂ ceramics has great promise as a dielectric resonator material for millimeter-wave use. The Al₂O₃TiO₂MnO system provides low dielectric constant and high quality factor (Q). TiO₂ and Al₂O₃ can compensate each other's temperature coefficient of resonant frequency. It is important to suppress the appearance of Al₂TiO₅ phase for obtaining high Q-value. In this study, dense Al₂O₃TiO₂ mixed ceramics without Al₂TiO₅ phase was synthesized by lowering the sintering temperature. The addition of MnO decreases the sintering temperature from 1400 to 1300 °C. In this temperature range, Al₂TiO₅ phase is hardly formed. X-ray powder diffraction (XRD) patterns show that the ceramics is composed of Al₂O₃ and TiO₂ phases only. Dense and well dispersed mixture of Al₂O₃ and TiO₂ grains is observed by scanning electron microscopy (SEM).The 0.9Al₂O₃0.1TiO₂ ceramics doped with 0.4 mol% of MnO has dielectric constant of 12.4, Q × f of 274,000 GHz at 76 GHz, and temperature coefficient of resonant frequency of +0.4 ppm/°C. The dielectric constant and the temperature coefficient of resonant frequency can be controlled by TiO₂ content. This ceramics is suitable for millimeter-wave applications because of its low dielectric constant, high Q-value, and small temperature coefficient of resonant frequency.     

Synthesis,pyrolysis of a novel liquid SiBCN ceramic precursor and its application in ceramic matrix composites

SiBCN ceramic precursor, polyborosilazane, was synthesized through a novel method which used sodium borohydride as boron source. Vinyl silazane with SiCl was converted to vinyl silazane with SiH structure, followed by hydroboration reaction and subsequent high-temperature reaction to form soluble polyborosilazane liquid. The process of precursor-to-ceramic conversion was almost completed before 800 °C and the cross-linked polyborosilazane precursor exhibited higher ceramic yield 75.6% at 1200 °C. The SiBCN ceramic annealed at 1400 °C contained BN, SiN and SiC bonds with smooth and dense surface and still retained principally amorphous structure up to 1600 °C. In addition, the viscosity of the polyborosilazane was 65 mPa.s, which can efficiently prepare ceramic matrix composite by means of precursor infiltration and pyrolysis (PIP). The density of as-obtained ceramic matrix composite (CMC) was 1.82 g/cm³, and the average bending strength, bending modulus and tensile strength were 265.2 MPa, 37.5 GPa and 158.6 MPa, respectively.     

On the nature of structural disorder in calcium silicate hydrates with a calcium/silicon ratio similar to tobermorite

Four calcium silicate hydrates (CSH) with structural calcium/silicon (Ca/Si) ratios ranging from 0.82 ± 0.02 to 0.87 ± 0.02 were synthesized at room temperature, 50, 80, and 110 °C. Their structure was elucidated by collating information from electron probe micro-analysis, transmission electron microscopy, extended X-ray absorption fine structure spectroscopy, and powder X-ray diffraction (XRD). A modeling approach specific to defective minerals was used because sample turbostratism prevented analysis using usual XRD refinement techniques (e.g. Rietveld analysis). It is shown that CSH with Ca/Si ratio of ~ 0.8 are structurally similar to nano-crystalline turbostratic tobermorite, a naturally occurring mineral. Their structure thus consists of sheets of calcium atoms in 7-fold coordination, covered by ribbons of silicon tetrahedra with a dreierketten (wollastonite-like) organization. In these silicate ribbons, 0.42 Si per bridging tetrahedron are missing. Random stacking faults occur systematically between successive layers (turbostratic stacking). Layer-to-layer distance is equal to 11.34 Å. Crystallites have a mean size of 10 nm in the a–b plane, and a mean number of 2.6–2.9 layers stacked coherently along the c* axis.     

A novel approach for preparation of dense TiC–SiC nanocomposites by sol–gel infiltration and spark plasma sintering

Dense TiC–SiC nanocomposite ceramics were prepared by infiltration of porous TiC scaffolds with a SiOC sol, followed by spark plasma sintering (SPS). The porous nano TiC scaffold was first synthesized by direct carbothermal reduction of a monolithic TiOC precursor obtained from a controlled sol–gel process. The TiC scaffold was infiltrated with a SiOC sol and then the sample was aged in a container for 48 h at 80 °C to convert the sol into gel. After this, the sample was heated at 550 °C to remove the organic components and then 1350 °C to convert the SiOC gel to SiC by carbothermal reduction reaction. The cycle of the infiltration and carbothermal reduction was repeated several times to obtain relatively dense TiC–SiC composite samples. Dense TiC–SiC composite with a uniform nano-sized grain microstructure was obtained by spark plasma sintering at 1800 °C for 5 min under 40 MPa uniaxial pressure. Compared with conventional powder mixing methods, the sol–gel infiltration approach has shown distinct advantages of achieving dense TiC–SiC composites with uniform nano-sized grain structures.     

Accelerating the crosslinking process of hyperbranched polycarbosilane by UV irradiation

A liquid hyperbranched polycarbosilane (LHBPCS) with stoichiometric C/Si ratio but without unsaturated groups was synthesized. Different from traditional thermal crosslinking, ultraviolet (UV) irradiation crosslinking was taken. The molecular weight, the consumption of SiH group and ceramic yield of LHBPCS showed an increase trend with increasing the UV irradiation time. After 30 min of UV irradiation, 71.8 wt% ceramic yield was obtained. In addition, extra divinyldimethylsilane was added into LHBPCS. Under UV irradiation, both the SiH group and vinyl group of divinyldimethylsilane were consumed. But the reaction extend of vinyl group was much faster than that of SiH group. Compared with pure LHBPCS, the mixture of LHBPCS and 5 wt% divinyldimethylsilane gave a higher ceramic yield of 79 wt% after 30 min of UV irradiation. By heating the crosslinked LHBPCS to 1000 °C, a near stoichiometric SiC ceramic was got. It exhibited excellent thermal stability at 1400 °C in air.