Laser-tungsten inert gas hybrid welding of dissimilar metals AZ31B Mg alloys to Zn coated steel

Laser-tungsten inert gas (TIG) hybrid welding has been developed for joining Mg alloys to Zn coated steel in a lap joint configuration. The joint could not be produced in laser or arc welding only, while acceptable joints without obvious defects were obtained with a relatively wide processing window in the hybrid process. Two reaction layers were observed to form at the interface and were identified as Mg–Zn eutectic structure (α-Mg + MgZn) and Fe₃Al phase by TEM analysis. In some cases, Al₆Mn phase also formed adjacent to the Fe–Al reaction layer. The tensile-shear strength attained the maximum value of 68 MPa, representing 52.3% joint efficiency relative to Mg base metal. The element Al from AZ31B Mg alloys diffused to the liquid/solid interface and then reacted with the elements from steel, such as Fe and Mn, contributing to the metallurgical bonding at the interface. The weak bonding between Mg–Zn reaction layer and newly formed Fe–Al layer resulted in the interfacial failure.     

Investigation of laser welding on butt joints of Al/steel dissimilar materials

Dissimilar metals of AA6013 aluminum alloy and Q235 low-carbon steel of 2.5 mm thickness were butt joined using a 10 kW fiber laser welding system with ER4043 filler metal. The study indicates that it is feasible to join aluminum alloy to steel by butt joints when zinc layer was hot-dip galvanized at the steel’s groove face in advance, and better weld appearance can be obtained at appropriate welding parameters. The joints had dual characteristics of a welding joint on the aluminum side and a brazing joint on the steel side. The smooth Fe₂Al₅ layer adjacent to the steel matrix and the serrated-shape FeAl₃ layer close to the weld metal were formed at the brazing interface. The overall thickness of Fe–Al intermetallic compounds layers produced in this experiment were varied from 1.8 μm to 6.2 μm at various welding parameters with laser power of 2.85–3.05 kW and wire feed speed of 5–7 m/min. The Al/steel butt joints were failed at the brazing interface during the tensile test and reached the maximum tensile strength of 120 MPa.     

Study of metallurgic and mechanical properties of laser welded heterogeneous joints between DP600 galvanised steel and aluminium 6082

This investigation focuses on the feasibility of heterogeneous welded joints between DP600 steel and aluminium 6082. The process adopted used a power laser in two modes: keyhole welding and laser-induced reactive wetting. All the results of the study show that the use of laser welding of galvanised sheets, in the keyhole mode, can achieve a joint shear strength of 140 MPa by optimising the process parameters and controlling the penetration, which must be limited to 600 μm. Another key factor with this welding method is control of the inter-sheet gap, which was achieved by using a clamping system that ensured a rigid joint while maintaining a constant gap sufficient to allow the escape of zinc vapour. This approach enabled an increase in shear strengths of 200 MPa to be obtained and the zinc acted as a beneficial factor to the welding process. With the laser-induced reactive wetting mode, the joint between galvanised sheets was more brittle because of the formation of a non-uniform reaction layer. With this mode, the presence of zinc is a factor that limits the growth of the reaction layer and, at the same time, leads to a mechanical deterioration of the joint; test results indicate that mechanical strength was limited to about 80 MPa.     

Microstructural development of diffusion-brazed austenitic stainless steel to magnesium alloy using a nickel interlayer

The differences in physical and metallurgical properties of stainless steels and magnesium alloys make them difficult to join using conventional fusion welding processes. Therefore, the diffusion brazing of 316L steel to magnesium alloy (AZ31) was performed using a double stage bonding process. To join these dissimilar alloys, the solid-state diffusion bonding of 316L steel to a Ni interlayer was carried out at 900 °C followed by diffusion brazing to AZ31 at 510 °C. Metallographic and compositional analyses show that a metallurgical bond was achieved with a shear strength of 54 MPa. However, during the diffusion brazing stage B₂ intermetallic compounds form within the joint and these intermetallics are pushed ahead of the solid/liquid interface during isothermal solidification of the joint. These intermetallics had a detrimental effect on joint strengths when the joint was held at the diffusion brazing temperature for longer than 20 min.     

Microstructure and tensile properties of laser beam welded Ti–22Al–27Nb alloys

Ti–22Al–27Nb alloys were welded using the laser beam welding process. The microstructure characterization and the tensile properties of the laser beam welded joints were investigated. The experimental results showed that a well-quality joint could be obtained using laser beam welding method. The fusion zone of the welded joint was composed of B2 phase. The tensile strength of the joints at room temperature was basically comparable to that of the base metal and the tensile ductility of the joints achieved 56% of the base metal. The average tensile strength of the welded joints at 650 °C was tested to be about 733 MPa, with the elongation of 2.93%.     

Microstructure characteristics and mechanical properties of cold metal transfer welding Mg/Al dissimilar metals

AZ31B Mg alloy and 6061 Al alloy were joined by using cold metal transfer (CMT) welding with pure copper (HS201) as the filler metal. The microstructure of Mg/Al CMT weld joint was studied by means of Optical Microscopy, Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDX), X-ray Diffraction (XRD). Results showed that dissimilar metals of Mg/Al could be successfully joined by CMT under proper processing parameters. The bonding strength of the joint was 34.7 MPa. A variety of Al–Cu intermetallic compounds, i.e. AlCu, CuAl₂, Cu₉Al₄, presented in the fusion zone of Al side, and Cu based solid solution was generated in weld zone, while Cu₂Mg and Al–Cu–Mg ternary eutectic structure was formed in the fusion zone of Mg side. The micro-hardness in the both sides of fusion zones increased sharply, which were 362 HV in Mg side and 260 HV in Al side. The joint was brittle fractured in the intermetallic compound layer of the fusion zone of Mg side, where plenty of Cu₂Mg intermetallic compounds were distributed continuously.     

Effect of gradient thermal distribution on butt joining of magnesium alloy to steel with Cu–Zn alloy interlayer by hybrid laser–tungsten inert gas welding

Experimental investigations on butt welding of magnesium alloy to steel by hybrid laser–tungsten inert gas (TIG) welding with Cu–Zn alloy interlayer are carried out. The results show that the gradient thermal distribution of hybrid laser–TIG welding, controlled by offset adjustment, has a noticeable effect on mechanical properties and microstructure of the joints. Particularly, at the offset of 0.2 mm, defect-free joints are obtained, and the tensile strength could attain a maximum value of 203 MPa. Moreover, the fracture of the joint with the 0.2 mm offset happens in the weld seam of Mg alloy instead of the Mg/Fe interface. Owning to the addition of the Cu–Zn alloy interlayer, a metallurgical bonding between Mg alloy and steel is achieved based on the formation of intermetallic compounds of CuMgZn and solid solutions of Cu and Al in Fe. Meanwhile, the same element distribution tendency of Fe and Al indicates the intimate interaction between Fe and Al in current experimental conditions.     

Microstructures and mechanical property of laser butt welding of titanium alloy to stainless steel

Laser butt welding of titanium alloy to stainless steel was performed. The effect of laser-beam offsetting on microstructural characteristics and fracture behavior of the joint was investigated. It was found that when the laser beam is offset toward the stainless steel side, it results in a more durable joint. The intermetallic compounds have a uniform thickness along the interface and can be divided into two layers. One consists of FeTi + α-Ti, and other consists of FeTi + Fe₂Ti + Ti₅Fe₁₇Cr₅. When laser beam is offset by 0 mm and 0.3 mm toward the titanium alloy side, the joints fracture spontaneously after welding. Durable joining is achieved only when the laser beam is offset by 0.6 mm toward the titanium alloy. From the top to the bottom of the joint, the thickness of intermetallic compounds continuously decreases and the following interfacial structures are found: FeAl + α-Ti/Fe₂Ti + Ti₅Fe₁₇Cr₅, FeAl + α-Ti/FeTi + Fe₂Ti + Ti₅Fe₁₇Cr₅ and FeAl + α-Ti, in that order. The tensile strength of the joint is higher when the laser beam is offset toward the stainless steel than toward the titanium alloy, the highest observed value being 150 MPa. The fracture of the joint occurs along the interface between two adjacent intermetallic layers.     

A novel weld-bonding hybrid process for joining Mg alloy and Al alloy

A novel weld-bonding hybrid process is carried out to join Mg alloy and Al alloy, and the technology combines a modified metal inert gas (MIG) spot welding process with adhesive bonding. The Mg base metal and the fusion zone are metallurgical connected by an Al–Mg transition layer with the thickness of 30–60 μm. Single nugget of spot welded joint can offer high shear strength of 130 MPa, which reach 81% of that of Mg base metal. The increased strength is due to the intermetallic layer being formed at the region with low stress, so the joint fractures in an Al-rich dendritic region. Superior mechanical properties can be obtained by weld bonded joint, benefiting from the advantages of both welding and adhesive bonding.     

Employment of fiber laser technology to weld austenitic stainless steel 304 l with aluminum alloy 5083 using pre-placed activating flux

The overlapping welding was carried out in keyhole mode between austenitic stainless steel 304 l and aluminum alloy 5083 using a low power fiber laser in continuous irradiation. The significant content of magnesium as the alloying element with low boiling point and high vapor pressure inside the AA 5083 matrix can induce the spatter formation and depression on surface of the weld beads upon laser beam absorption and temperature growth which can deteriorate the mechanical properties and appearance of the joints. To reduce these defects, a variety of single and multi-components activating fluxes including oxide-based TiO₂ and halide-based CaF₂ flux powders were pre-placed on the surface of welding material prior to laser welding. The EDX and XRD analyses in addition to microhardness and shear tests were carried out to characterize the joints. The obtained results showed that, the oxide and halide activating fluxes can significantly improve the joints' strength up to 1.48 and 1.85 times in average respectively compared with autogenous joint. It was deduced that the simultaneous effect of significant decrease in joints' surface depression leading to welds' geometry improvement in addition to less formation of interfacial Fe–Al intermetallics, were the major causes for considerable strength improvements.     

Comparative study on microstructure and mechanical properties of laser welded–brazed Mg/mild steel and Mg/stainless steel joints

A laser welding–brazing (LWB) technology using Mg based filler has been developed for joining Mg alloy to mild steel and Mg alloy to stainless steel in a lap configuration. Microstructure and mechanical properties of laser welded–brazed lap joints in both cases were comparatively studied. The results indicated that no distinct reaction layer was observed at the interface of Mg/mild steel and subsequently the interface was confirmed as mechanical bonding, whereas an ultra thin reaction layer with a continuous and uniform morphology was evidenced at the Mg/stainless steel interface, which was indicative of metallurgical bonding. The newly formed interfacial layer was indexed as FeAl phase by transmission electron microscopy (TEM) combined with energy dispersive spectroscopy (EDS). The average tensile–shear strength of Mg/mild steel joint was only 142 N/mm with typical interfacial failure, while that of Mg/stainless steel joint could reach 270 N/mm, representing 82.4% joint efficiency relative to the Mg alloy base metal. The fracture location of Mg/stainless steel joint was at Mg fusion welding side, suggesting the interface was not weak point due to the formation of ultra thin interfacial layer. The role of alloying elements in base metal and bonding mechanism of the interfacial layer were discussed, respectively.     

Analysis of process parameters effects on friction stir welding of dissimilar aluminum alloy to advanced high strength steel

Thin sheets of aluminum alloy 6061-T6 and one type of Advanced high strength steel, transformation induced plasticity (TRIP) steel have been successfully butt joined using friction stir welding (FSW) technique. The maximum ultimate tensile strength can reach 85% of the base aluminum alloy. Intermetallic compound (IMC) layer of FeAl or Fe₃Al with thickness of less than 1 μm was formed at the Al–Fe interface in the advancing side, which can actually contribute to the joint strength. Tensile tests and scanning electron microscopy (SEM) results indicate that the weld nugget can be considered as aluminum matrix composite, which is enhanced by dispersed sheared-off steel fragments encompassed by a thin intermetallic layer or simply intermetallic particles. Effects of process parameters on the joint microstructure evolution were analyzed based on mechanical welding force and temperature that have been measured during the welding process.     

High power fiber laser arc hybrid welding of AZ31B magnesium alloy

High power fiber laser–metal inert gas arc hybrid welding of AZ31B magnesium alloy was studied. The fusion zone consisted of hexagonal dendrites, where the secondary particle of Al₈Mn₅ was found at the center of dendrite as a nucleus. Within hybrid weld, the arc zone had coarser grain size and wider partial melted zone compared with the laser zone. The tensile results showed the maximum strength efficiency of 5 mm thick welds was up to 109%, while that of 8 mm thick welds was only 88%. The fracture surface represented a ductile–brittle mixed pattern characterized by dimples and quasi-cleavages. On the fracture surface some metallurgical defects of porosity and MgO inclusions around with secondary cracks were observed. Meanwhile, a strong link between the joint strength and weld porosity were demonstrated by experimental results, whose relevant mechanism was discussed by the laser–arc interaction during hybrid welding.     

Microstructure and mechanical properties of dissimilar Al alloy/steel joints prepared by a flat spot friction stir welding technique

The 6061-T6 Al alloy and mild steel plate with a thickness of 1 mm were successfully welded by the flat spot friction stir welding technique, which contains two steps during the entire welding process. The rotating tools with different probe lengths of 1.0, 1.3 and 1.5 mm were used in the first step, during which a conventional spot FSW was conducted above a round dent previously made on the back plate. However, sound Al/Fe welds with similar microstructure and mechanical properties can still be obtained after the second step, during which a probe-less rotating tool was used to flatten the weld surface. The sound welds have smooth surface without keyholes and other internal welding defects. No intermetallic compound layer but some areas with amorphous atomic configuration was formed along the Al/Fe joint interface due to the lower heat input. The shear tensile failure load can reach a maximum value of 3607 N and fracture through plug mode. The probe length has little effect on the weld properties, which indicates that the tool life can be significantly extended by this new spot welding technique.     

Interfacial microstructure and mechanical property of resistance spot welded joint of high strength steel and aluminium alloy with 4047 AlSi12 interlayer

Dissimilar materials of H220YD galvanised high strength steel and 6008-T66 aluminium alloy were welded by means of median frequency direct current resistance spot welding with employment of 4047 AlSi12 interlayer. Effects of interlayer thickness on microstructure and mechanical property of the welded joints were studied. The welded joint with interlayer employed could be recognised as a brazed joint. The nugget diameter had a decreased tendency with increasing thickness of interlayer under optimised welding parameters. An intermetallic compound layer composed of Fe₂(Al,Si)₅ and Fe₄(Al,Si)₁₃ was formed at the interfacial zone in the welded joint, the thickness and morphology of which varying with the increase of interlayer thickness. Reaction diffusion at the steel/aluminium interface was inhibited by introduction of silicon atoms, which restricted growth of Fe₂(Al,Si)₅. Tensile shear load of welded joints experienced an increased tendency with increasing interlayer thickness from 100 to 300 μm, and the maximum tensile shear load of 6.2 kN was obtained with interlayer thickness of 300 μm, the fractured welded joint of which exhibiting a nugget pullout failure mode.     

Optimization of deep penetration laser welding of thick stainless steel with a 10 kW fiber laser

Deep penetration laser welding of 12 mm thick stainless steel plates was conducted using a 10 kW high-power fiber laser. The effect of the processing parameters on the weld bead geometry was examined, and the microstructure and mechanical properties of the optimal joint were investigated. The results show that the focal position is a key parameter in high-power fiber laser welding of thick plates. There is a critical range of welding speed for achieving good full penetration joint. The type of top shielding gas influences the weld depth. The application of a bottom shielding gas improves the stability of the entire welding process and yields good weld appearances at both the top and bottom surfaces. The maximum tensile stress of the joint is 809 MPa. The joint fails at the base metal far from the weld seam with a typical cup–cone-shaped fracture surface. The excellent welding appearance and mechanical properties indicate that high-power fiber laser welding of a 304 stainless steel thick plate is feasible.     

Effect of applying electrical potential to a CO2 laser welding of different thickness plates

This study was aimed at developing laser welding with an applied voltage potential to increase the bead root width in laser welding. Also, in order to enhance the welding speed and the butt joint gap tolerance, the influences of the experimental conditions: supplied voltage between plate and backside electrode, welding speed, plasma operate gaseous species, and the butt joint gap, on the bead root width were investigated. Although it is necessary to avoid over heating and melting the plates, it is applicable for higher speed and wider gap butt joint welding than a conventional laser welding. In the case of butt joint welding with a thickness of 2.0 and 0.8 mm steel sheets by using 5 kW CO₂ laser system, it is concluded that this method is effective for increasing of the welding speed from 5 to 8 m/min. Knowledge of optimum conditions and configurations has guided to extend this process to more challenging structural materials such as a tailored blank steel sheet.     

Interface microstructure and mechanical properties of arc spot welding Mg–steel dissimilar joint with Cu interlayer

A novel technology was developed for the arc spot welding of AZ31 Mg alloy to Q235 steel with Cu as interlayer. The mechanisms of bonding dissimilar materials were investigated using mechanical and metallurgical examinations. Results show that the joining of Mg alloy to steel with Cu involved two bonding mechanisms: weld-brazing by the Cu transition layer at the interface edge and bonding by a micron-scale composite transition layer of Al₃Cu₄Fe₃ and Fe₄Cu₃ intermetallic phases at the interface center. The additional reaction of Cu increased the reaction temperature and composition ranges at the interface. It also elicited a bridge effect that improved the weldability of Mg alloy and steel by new formed phases.     

Optimised design of electrode morphology for novel dissimilar resistance spot welding of aluminium alloy and galvanised high strength steel

A novel resistance spot welding method of dissimilar materials of 6008-T66 aluminium alloy and H220YD galvanised high strength steel was presented, and the morphology of welding electrodes was designed optimally. Macrostructure, microstructure and mechanical property of the welded joints obtained with optimised electrodes were studied. Numerical simulation of current density distribution and temperature field during welding was also performed. The optimised electrodes were a planar circular tip electrode with tip diameter of 10 mm on the steel side and a spherical tip electrode with spherical diameter of 70 mm on the aluminium alloy side. The welded joint obtained with optimised electrodes could be regarded as a special welded-brazed joint, and an intermetallic compound layer composed of Fe₂Al₅ and Fe₄Al₁₃ with maximum thickness of about 4.0 μm was formed at the aluminium/steel interface in the welded joint. Tensile shear load up to 5.4 kN was achieved for the welded joint obtained with optimised electrodes. Current density distribution during welding with optimised electrodes was more homogeneous than that with F type electrodes. Furthermore, interfacial temperature in the welded joint during welding with optimised electrodes (about 915 °C) was lower than that with F type electrodes (about 985 °C).     

Ultrafine grain structure features in spray-formed AZ31 magnesium alloy

The ultrafine grain structure was developed in spray-formed AZ31 magnesium alloy by optimizing delivery tube orifice diameter. A significant refinement of grain size ∼1 μm in ultrafine level was achieved by using 2.25 mm delivery tube orifice diameter. The tensile strength value was increased from 145 MPa of as-cast alloy to 250 MPa of spray-formed alloy, registering an enhancement of ∼72%. On the other hand, elongation was increased from 6% to 13% using 2.25 mm orifice, registering more than onefold increase in elongation. Also, hardness enhancement of ∼49% was observed in spray-formed AZ31 alloy compared to as-cast alloy. The fracture surface of spray-formed AZ31 Mg alloy evidences the mixed type of ductile and brittle fracture.