Reduction of thermal residual stresses of laminated polymer composites by addition of carbon nanotubes

This paper studies the effects of multi-walled carbon nanotubes (MWCNTs) on the thermal residual stresses in polymeric fibrous composites. Reinforced ML-506 epoxy nanocomposites with different amounts of homogeneously dispersed MWCNTs (0.1 wt.%, 0.5 wt.% and 1 wt.%) were fabricated using the sonication technique. Thermo-mechanical analysis and tensile tests of the specimens were carried out to characterize the thermal and mechanical properties of MWCNTs/epoxy composites. Due to the negative thermal expansion and high modulus of MWCNTs, addition of MWCNTs resulted in a great reduction of the coefficient of thermal expansion (CTE) of epoxy. The MWCNTs also moderately increased the Young’s modulus of the epoxy. Then, the effects of adding MWCNTs on micro and macro-residual stresses in carbon fiber (CF)/epoxy laminated composites were investigated using the energy method and the classical lamination theory (CLT), respectively. The results indicated that the addition of low amounts of MWCNTs leads to a considerable reduction in thermal residual stress components in both micro and macro levels.     

Mechanical performance of epoxy matrix hybrid nanocomposites containing carbon nanotubes and nanodiamonds

A novel class of epoxy matrix hybrid nanocomposites has been developed containing multiwalled carbon nanotubes (MWCNTs) and nanodiamonds (NDs) to explore the combined effect of nanoreinforcements on the mechanical performance of nanocomposites. Both the nanofillers were functionalized before incorporating into epoxy matrix to promote interfacial interactions. The concentrations of both MWCNTs and NDs in the nanocomposites were increased systematically, i.e. 0.05 wt.%, 0.1 wt.% and 0.2 wt.% while composites containing individual nanoreinforcements were also manufactured for comparison. The developed nanocomposites were characterized microstructurally by scanning electron microscopy (SEM) and mechanically by tensile, flexural, impact and hardness tests. Homogeneous dispersion of MWCNTs and NDs was observed under SEM, which resulted in the enhancement of mechanical properties of nanocomposites. The composites containing 0.2 wt.% MWCNTs and 0.2 wt.% NDs showed 50% increase in hardness while tensile strength and modulus enhanced to 70% and 84%, respectively. Flexural strength and modulus also showed a rise of 104% and 56%, respectively. Interestingly, fracture strain also increased in both the tensile and flexural testing. The impact resistance increased to 161% showing a significant improvement in the toughness of hybrid nanocomposites.     

Fabrication and characterization of three-dimensional nanofiber membrance of PCL–MWCNTs by electrospinning

The uniform and highly smooth nanofibers of poly(ε-caprolactone) (PCL) composited with different multi-walled carbon nanotubes (MWCNTs) content (ranging from 0.1 wt.% to 5 wt.%) were successfully prepared by electrospinning method without the occurrence of bead defects in this study. The PCL–0.5 wt.%MWCNTs nanofiber membrane exhibited the maximum tensile strength (about 1.42 MPa), which was increased by 46% compared with that of electrospun pure PCL nanofiber membrane. Moreover, the PCL–MWCNTs nanofiber membrane exhibited three-dimensional porous structure with a high porosity over 90%. The average diameter of PCL–MWCNTs nanofibers decreased with the addition of MWCNTs and there was a narrow diameter distribution in the range of 52–244 nm when the amount of MWCNTs was 0.5 wt.%. Compared with pure PCL nanofibers, PCL–MWCNTs nanofibers showed accelerating degradation behavior. In addition, the cytotoxicity results revealed that the electrospun PCL–MWCNTs nanofiber membranes possessed good in vitro biocompatibility, and hemolysis and kinetic clotting tests indicated that the PCL nanofiber membranes did not enhance blood coagulation after the addition of MWCNTs. It can be concluded that such kind of electrospun PCL–MWCNTs nanofibers may be promising candidate for tissue engineering scaffold application.     

Effect of different carbon nano-fillers on rheological properties and lap shear strength of epoxy adhesive joints

In this work, the rheological properties, thermal stability and the lap shear strength of epoxy adhesive joints reinforced with different carbon nano-fillers such as multi-walled carbon nanotubes (CNT), graphene nanoplatelets (GNP) and single-walled carbon nanohorns (CNH) have been studied. The nano-fillers were dispersed homogeneously using Brabender® Plasti-Corder®. The epoxy pre-polymer with and without the nano-fillers exhibited shear thinning behavior. The nano-filler epoxy mixtures exhibited a viscoplastic behavior which was analyzed using Casson’s model. Thermo-gravimetric analysis indicated an increase in the thermal stability of the epoxy with the addition of carbon nano-fillers. Carbon nano-fillers resulted in increased lap shear strength having high Weibull modulus. The joint strength increased by 53%, 49% and 46% with the addition of 1 wt.% CNT, 0.5 wt.% GNP and 0.5 wt.% CNH, respectively. The strength of the joints having high filler content (>1 wt.%) was limited by mixed mode type of failure.     

Tribological performance of carbon nanotube–graphene oxide hybrid/epoxy composites

An investigation is conducted on the effect of the hybrid of multi-wall carbon nanotubes (MWCNTs) and graphene oxide (GO) nanosheets on the tribological performance of epoxy composites at low GO weight fractions of 0.05–0.5 phr. The MWCNT amount is kept constant at 0.5 phr, which is typical for CNT/epoxy composites with enhanced mechanical properties. Friction and wear tests against smooth steel show that the introduction of 0.5 phr MWCNTs into the epoxy matrix increases the friction coefficient and decreases the specific wear rate. When testing the tribological performance of MWCNT/GO hybrids, it is shown that at a high GO amount of 0.5 phr, the friction coefficient is decreased below that of the neat matrix whereas the wear rate is increased above that of the neat matrix. At an optimal hybrid formulation, i.e., 0.5 phr MWCNTs and 0.1 phr GO, a further increase in the friction coefficient and a further reduction in the specific wear rate are observed. The specific wear rate is reduced by about 40% down to a factor of 11 relative to the neat epoxy when the GO content is 0.1 phr.     

Electromagnetic interference shielding of composites consisting of a polyester matrix and carbon nanotube-coated fiber reinforcement

We investigated the electromagnetic interference shielding effectiveness (EMI SE) of composites consisting of an unsaturated polyester matrix containing woven glass or carbon fibers that had been coated with multiwalled carbon nanotubes (MWCNTs). Composite panels consisting of fiber fabrics with various combinations of fabric type and stacking sequence were fabricated. Their EMI SE was measured in the frequency range of 30 MHz–1.5 GHz. The underlying physics governing the EMI shielding mechanisms of the materials, namely, absorption, reflection, and multiple reflections, was investigated and used in analytical models to predict the EMI SE. Simulation and experimental results showed that the contributions of reflection and absorption to EMI shielding is enhanced by sufficient impedance mismatching, while multiple reflections have a negative effect. For a given amount of MWCNTs in the glass-fiber–reinforced composite, coating the outermost, instead of intermediate, glass fiber plies with MWCNTs was found to maximize the conductivity and SE.     

Physical,mechanical and morphological properties of polymer composites manufactured from carbon nanotubes and wood flour

The objective of this investigation was to evaluate physical, mechanical and morphological properties of experimental polymer type panels made from single-wall carbon nanotube (SWCNT) and wood flour. The composites with different SWCNTs (0, 1, 2, 3 phc) and maleic anhydride grafted polyethylene (MAPE) (0 and 3 phc) contents were mixed by melt compounding in an internal mixer and then the composites manufactured by injection molding method. The mass ratio of the wood flour to LDPE was 50/50 (w/w) in all compounds. Water absorption, thickness swelling, bending characteristics, impact strength and morphological properties of the manufactured composites were evaluated. Based on the findings in this work the water absorption and thickness swelling of the nanocomposites decreased with increasing with amount of the SWCNTs (from 1 to 3 phc) and MAPE (3 phc) in the panels. The mechanical properties of LDPE/wood-flour composites could be significantly enhanced with increased percentage of MAPE and SWCNTs content. Panels having 2 phc SWCNTs and 3 phc MAPE exhibited the highest impact strength value. Also Scanning Electron Microscope (SEM) micrographs showed that carbon nanotubes can fill the voids of wood plastic composites as well as addition of MAPE and SWCNTs enhanced interaction between the components.     

Evaluating the effects of multi-walled carbon nanotubes on the mechanical properties of chopped strand mat/polyester composites

In this research, the influence of adding multi-walled carbon nanotubes at various contents on the mechanical properties of chopped strand mat/polyester composites was investigated. Initially, the effect of the sonication time on the dispersion of carbon nanotube at the highest weight ratio (0.5 wt.%) was inspected. To achieve this goal, a new technique based on scanning electron microscopy, which utilizes the burn-off test, was introduced to visualize the dispersion state of carbon nanotubes. Subsequently, the effect of addition of multi-walled carbon nanotube on the tensile and flexural properties of the fiber reinforced composites was studied. The results of mechanical tests showed that adding only 0.05 wt.% carbon nanotube enhanced the flexural strength of the hybrid composite by 45% while the tensile strength was not changed significantly. Improvements in the tensile and flexural moduli were also observed. Moreover, theoretical relations between the tensile, flexural and compressive moduli based on the classical beam theory were employed to determine the effect of carbon nanotube on the compressive modulus of composites. The theoretical result showed 31% enhancement in the compressive modulus.     

Strain sensing in polymer/carbon nanotube composites by electrical resistance measurement

In this work multiwall carbon nanotubes (MWCNTs) dispersed in a polymer matrix have been used for strain sensing of the resulting nanocomposite under tensile loading. This was achieved by measuring the relative electrical resistance change (ΔR/R₀) in conductive polyvinylidenefluoride (PVDF)/MWCNTs nanocomposites prepared by melt-mixing with varying filler content from 0.5 wt.% to 8 wt.%. Two main parameters were systematically studied. The PVDF/MWCNTs mixing procedure that results in a successful MWCNTs dispersion, and the effect of MWCNTs content on material’s sensing behaviour. The samples were subjected to tensile loading and the longitudinal strain was monitored together with the longitudinal electrical resistance. The results showed that MWCNTs dispersed in insulating PVDF matrix have the potential to be used as a sensitive network to monitor the strain levels in polymer/carbon nanotube nanocomposites as the deformation level of each sample was being reflected by the resistance changes.     

Preparation and characterization of multi-walled carbon nanotube/hydroxyapatite nanocomposite film dip coated on Ti–6Al–4V by sol–gel method for biomedical applications: An in vitro study

In the present research, the introduction of multi-walled carbon nanotubes (MWCNTs) into the hydroxyapatite (HA) matrix and dip coating of nanocomposite on titanium alloy (Ti–6Al–4V) plate was conducted in order to improve the performance of the HA-coated implant via the sol–gel method. The structural characterization and electron microscopy results confirmed well crystallized HA–MWCNT coating and homogenous dispersion of carbon nanotubes in the ceramic matrix at temperatures as low as 500 °C. The evaluation of the mechanical properties of HA and HA/MWCNT composite coatings with different weight percentages of MWCNTs showed that the addition of low concentrations of MWCNTs (0.5 and 1 wt.%) had improved effect on the mechanical properties of nanocomposite coatings. Moreover, this in vitro study ascertained the biocompatibility of the prepared sol–gel-derived HA/MWCNT composite coatings.     

Strain and damage monitoring in carbon-nanotube-based composite under cyclic strain

The resistive behavior of multi-walled carbon nanotube (MWCNT)/epoxy resins, tested under mechanical cycles and different levels of applied strain, was investigated for specimens loaded in axial tension. The surface normalized resistivity is linear with the strain for volume fraction of MWCNTs between 2.96 × 10⁻⁴ and 2.97 × 10⁻³ (0.05 and 0.5% wt/wt). For values lower than 0.05% wt/wt, close to the electrical percolation threshold (EPT) a non-linear behavior was observed. The strain sensitivity, in the range between 0.67 and 4.45, may be specifically modified by controlling the nanotube loading, in fact the sensor sensitivity decreases with increasing the carbon nanotubes amount. Microscale damages resulted directly related to the resistance changes and hence easily detectable in a non-destructive way by means of electrical measurements. In the fatigue tests, the damage is expressed through the presence of a residual resistivity, which increases with the amount of plastic strain accumulated in the matrix.     

Mechanical properties of nanostructured Al2024–MWCNT composite prepared by optimized mechanical milling and hot pressing methods

Nanostructured Al2024–multiwall carbon nanotubes (MWCNTs) composites were produced using optimized mechanical milling and hot pressing methods. Nanostructured Al2024 powder was first prepared through 30 h mechanical milling of the alloy powder. MWCNTs up to 3 vol.% were added to the milled Al2024 powder and milled for different times. Differential thermal analysis (DTA) and X-ray diffraction (XRD) were used to assess the structural changes and thermal behavior during mechanical milling and hot pressing. Hardness and compression tests were applied on bulk samples to evaluate their mechanical properties. Mechanical milling applied on Al2024 powders for 30 h resulted in the grain refinement to ～30 nm. DTA analysis showed an endothermic peak at ～632 °C due to Al2024 melting and an exothermic peak between 645 and 658 °C related to Al and MWCNTs reaction. Mechanical milling of nanocomposite powder for 4 h and following hot pressing at 500 °C under a pressure of 250 MPa for 0.5 h were selected as optimized conditions for bulk nanocomposite preparation. With MWCNTs addition up to 2 vol.%, relative density remained at 98%, and hardness increased to 245 HV. Compressive strength of nanocomposites found a maximum value of 810 MPa at 2 vol.% MWCNTs addition which is 78%, 34% and 12% greater than that for Al2024–O, Al2024–T6 and nanostructured Al2024, respectively.     

Characteristics of multi-walled carbon nanotubes and background aerosols by carbon analysis; particle size and oxidation temperature

Novel carbonaceous nanomaterials such as carbon nanotubes and fullerenes have many beneficial characteristics as industrial materials, but exposure to these nanomaterials also poses health risks. As part of an exposure assessment, we characterized the following carbonaceous nanomaterials, using an aerosol carbon monitor: nine samples of multi-walled carbon nanotubes (MWCNTs), a sample of single-walled carbon nanotubes (SWCNTs), a standard sample of diesel exhaust particles (DEPs), and an ambient particulate matter (APM). The amounts of elemental carbon (EC) determined by the monitor coincided with the mass of MWCNTs calibrated by a microbalance. The carbonaceous nanomaterials were oxidized in three steps of oven temperatures (550, 700 and 920 °C) in this method. The portion of oxidized carbon at each temperature depended on the sample characteristic. We used the monitor to analyze the aerosol samples collected in five stages by a Sioutas cascade impactor (SCI), which collects size-segregated airborne particles having aerodynamic diameters from 6.6 μm to less than 0.25 μm. As MWCNTs aggregate/agglomerate easily, the size was of a good parameter to distinguish the MWCNTs from other materials. Two-dimensional mapping by size and oxidized temperature suggested the origin of the carbonaceous aerosol samples. Based on the results, we reanalyzed our previous data obtained at a factory manufacturing MWCNTs. The characteristics of workplace samples by particle size and carbon analysis were similar to those of MWCNT aerosol particles.     

Microstructure and mechanical property of multi-walled carbon nanotubes reinforced aluminum matrix composites fabricated by friction stir processing

Aluminum matrix composites reinforced by different contents of multi-walled carbon nanotubes (MWCNTs) were fabricated by friction stir processing (FSP). The microstructure of nano-composites and the interface between aluminum matrix and MWCNTs were examined using optical microscopy (OM) and transmission electron microscopy (TEM). It was indicated that MWCNTs were well dispersed in the aluminum matrix throughout the FSP. Tensile tests and microhardness measurement showed that, with the increase of MWCNT content, the tensile strength and microhardness of MWCNTs/Al composites gradually increased, but on the contrary, the elongation decreased. The maximum ultimate tensile strength reached up to 190.2 MPa when 6 vol.% MWCNTs were added, and this value was two times more of that of aluminum matrix. Appearances and fracture surface micrographs of failed composite samples indicated that the composites become more and more brittle with the increase of the MWCNT content.     

Fracture behaviour of α-Al2O3 ceramics reinforced with a mixture of single-wall and multi-wall carbon nanotubes

The extraordinary mechanical properties of single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes (MWCNTs) have generated interest in incorporating them as toughening agents in ceramics. This work describes the fracture behaviour of an alumina (Al₂O₃) ceramic reinforced with a mixture of 0.05 wt% MWCNTs + 0.05 wt% SWCNTs. The CNT/Al₂O₃ nanocomposite was pressureless sintered in air using graphite powder as bed powder at 1520 °C for 1 h. The hardnesses and fracture toughnesses were lower than for pure Al₂O₃ and Al₂O₃ + 0.1 wt% SWCNTs and Al₂O₃ + 0.1 wt% MWCNTs. A predominantly transgranular fracture mode with a decrease in crack deflection and no pull-out was observed in the SWCNT + MWCNT–Al₂O₃ nanocomposite. MWCNTs had to the best reinforcing effect in Al₂O₃ nanocomposite.     

Determination of Pb2+ ions by a modified carbon paste electrode based on multi-walled carbon nanotubes (MWCNTs) and nanosilica

A novel carbon paste ion selective electrode for determination of trace amount of lead was prepared. Multi-walled carbon nanotubes (MWCNTs) and nanosilica were used for improvement of a lead carbon paste sensor response. MWCNTs have a good conductivity which helps the transduction of the signal in carbon paste electrode. The electrode composition of 20 wt% paraffin oil, 57% graphite powder, 15% ionophore (thiram), 5% MWCNTs, and 3% nanosilica showed the stable potential response to Pb²⁺ ions with the Nernstian slope of 29.8 (±0.2) mV decade^?1 over a wide linear concentration range of 10^?7–10^?2 mol L^?1. The electrode has fast response time, and long term stability (more than 2 months). The proposed electrode was used to determine the concentration of lead ions in waste water and black tea samples.     

Effect of matrix glass transition on reinforcement efficiency of epoxy-matrix composites with single walled carbon nanotubes,multi-walled carbon nanotubes,carbon nanofibers and graphite

This study compares the mechanical and thermal properties of glassy and rubbery epoxy–matrix composites reinforced with 1 and 4 wt.% single-walled carbon nanotubes (SWCNTs), multi-walled carbon nanotubes (MWCNTs), graphite, and carbon nanofibers (CNFs). The tensile modulus of most glassy composites was higher than that of the epoxy and increased with higher filler concentration and 4% graphite/epoxy and 4% SWCNT/epoxy exhibited approximately the same highest tensile modulus. The elongation of glassy composites was significantly lower than that of the epoxy and decreased with increasing filler loading. Most rubbery composites showed a higher tensile modulus and elongation than the epoxy and the modulus increased with rising filler content and 4% SWCNT/epoxy showed the highest tensile modulus and tensile strength. In the rubbery regime, glassy and rubbery composites displayed a higher storage modulus than the corresponding epoxy and 4 wt.% SWCNT/epoxy composites showed a 300% improvement in storage modulus compared to the epoxy.     

A surfactant dispersed SWCNT-polystyrene composite characterized for electrical and mechanical properties

Single wall carbon nanotubes (SWCNTs) were dispersed in polystyrene (PS) at 0.1, 0.2, 0.3 and 1.0 wt.% (weight percent) concentrations using a surfactant assisted method. The resulting nanocomposites were characterized for their electrical conductivity, mechanical strength and fracture toughness properties. Results show a significant improvement in electrical conductivity with electrical percolation occurring by 0.2 wt.% SWCNT loading and the SWCNT-PS nanocomposite fully conductive at 1.0 wt.%. Three-point bend tests showed a decline in flexural strength and break strain with the addition of 0.1 wt.% SWCNTs. Improvements in the flexural modulus, strength and break strain with increasing SWCNT wt.% content followed The fracture toughness of the SWCNT-PS nanocomposites, in terms of the critical stress-intensity factor K_IC, was reduced relative to the neat material. From optical and high resolution scanning electron microscopy the presence of the carbon nanotubes is shown to have an adverse effect on the crazing mechanism in this PS material, resulting in a deterioration of the mechanical properties that depend on this mechanism.     

Alignment of muscle precursor cells on the vertical edges of thick carbon nanotube films

The development of scaffolds and templates is an essential aspect of tissue engineering. We show that thick (> 0.5 mm) vertically aligned carbon nanotube films, made by chemical vapour deposition, can be used as biocompatible substrates for the directional alignment of mouse muscle cells where the cells grow on the exposed sides of the films. Ultra high resolution scanning electron microscopy reveals that the films themselves consist mostly of small diameter (10 nm) multi-wall carbon nanotubes of wavy morphology with some single wall carbon nanotubes. Our findings show that for this alignment to occur the nanotubes must be in pristine condition. Mechanical wiping of the films to create directional alignment is detrimental to directional bioactivity. Larger areas for study have been formed from a composite of multiply stacked narrow strips of nanotubes wipe-transferred onto elastomer supports. These composite substrates appear to show a useful degree of alignment of the cells.