Gas–liquid mass transfer studies for biomass support materials in a bioreactor

BACKGROUND: Oxygen mass transfer can be described and analyzed by means of the mass transfer coefficient k_La, which is the most important parameter involved in the design and operation of mixing–sparging equipment for bioreactors. In the present study, the effect of biomass support materials on the gas–liquid mass transfer coefficient was studied in a bioreactor under variable process conditions. The biomass support materials used were activated carbon, pumice and loofa sponge. RESULTS: Compared with the case with distilled water only, the presence of the biomass support materials negatively influenced mass transfer. On the other hand, the mass transfer coefficient increased with increased impeller speed, air flow rate and temperature; and decreased with the increase of liquid viscosity and biomass support material concentration for all cases. CONCLUSIONS: Evaluation of the experimental data showed that k_La values were affected by process variables. Besides the major exponential correlations used in the literature, satisfactory linear correlations for the relationship between the k_La and process variables were obtained. Copyright © 2010 Society of Chemical Industry     

Mass transfer behaviour of gas-liquid jet loop reactors

A special type of jet loop reactor (JLR), designed for continuous operation and short residence times was investigated with regard to its mass transfer behaviour, described by the volumetric mass transfer coefficient k_La. The jet stream and superficial gas velocities are varied in two JLRs of different sizes, equipped with different nozzles. Fully desalinated water, 0.08 molar NaCI solution and solutions of different concentration of carboxymethyl cellulose (CMC) are used as the liquid phase. A steady-state physical method is employed to determine k_La: air oxygen is purged from the liquid phase by gaseous nitrogen. The measurements show that the reactor is characterized by high power density and high mass transfer performance. No limit of mass transfer capacity was observed in the chosen ranges of volumetric gas and liquid flow rates, i.e. at a given jet stream velocity, the relationship between k_La and the superficial gas velocity is nearly linear. The investigations show that the mass transfer contributed by the jet stream largely depends on liquid phase composition.     

Absorption and desorption of carbon dioxide in several water types

This study investigated the effect of water type on the rate of CO₂ transfer from/to an aqueous phase with varying degree of water salinity. The absorption and desorption experiments were conducted on reverse osmosis product, brackish well, and brackish water reverse osmosis reject waters as well as seawater in a mechanically agitated tank. Results show that the direction of mass transfer has a major impact on the value of the volumetric mass transfer coefficient, k_La, with the absorption experiments always rendering higher values. Furthermore, k_La values always decreased with salinity in both absorption and desorption experiments until a certain critical salinity value was reached, beyond which mass transfer increased again. However, k_La values were found to decrease continuously with an increase in the water alkalinity in absorption experiments, while no clear conclusion could be drawn for the alkalinity effect in the case of desorption experiments. These observations suggest that the effect of alkalinity should be further investigated to elucidate its impact along with the salinity on the volumetric mass transfer rate.     

Volumetric mass transfer coefficients in an internal loop airlift reactor with low‐density particles

The influence of organic additives (propanol, benzoic acid, isoamyl alcohol and carboxymethylcellulose) on the volumetric mass transfer coefficient, k_La, in an internal loop airlift reactor with low‐density particles (nylon‐6 and polystyrene) was investigated. The k_La values increased with increase in superficial gas velocity, U_sg, and decreased with increase in solid loading. A draft tube to reactor diameter ratio, D_R/D, of 0.4 gave maximum k_La values. The addition of benzoic acid and propanol increased the k_La values owing to their coalescence inhibiting characteristics. The addition of isoamyl alcohol decreased k_La, owing to the formation of rigid bubbles and recirculation of small bubbles having a low oxygen content. The k_La values decreased with increase in the concentration of the non‐Newtonian fluid carboxymethylcellulose (CMC). The proposed correlations predicted the experimental data well. Copyright © 2006 Society of Chemical Industry     

Modelling mass transfer in an aerated 0.2 m vessel agitated by Rushton, Phasejet and Combijet impellers

We assembled a set of models that allows investigation of local variables that are difficult to measure, validation of mechanistic physical models, and comparison of different numerical solutions. Population balances (PB) for bubbles were combined with local flow modelling in order to investigate G–L mass transfer in an air–water system. Performance of three different impeller geometries was investigated: Rushton (RT), Phasejet (PJ) and Combijet (CJ). Simulations were compared against experimental mixing intensity, gas hold-up, vessel-averaged volumetric mass transfer rates (k_La), and local bubble size distributions (BSDs).The simulations qualitatively predict k_La's with different impellers at the fully dispersed flow region and gave new insight on how k_La is formed and distributed in the stirred vessels. The used bubble breakage and coalescence models are able to describe both air–water and viscous non-Newtonian G–L mass transfer. Difference between experimental mass transfer rates of the three impellers was within experimental error, even trough the flow patterns, gas distribution, and local BSDs differ considerably. The population balance for bubbles was modelled in two different ways, with multiple size groups (MUSIGs) and with the bubble number density (BND) approach. MUSIG calculations took over twice as much computational time than BND, but there was little difference in the results. The Rushton turbine k_La was described with best accuracy, which is not surprising since most phenomenological models are fitted based on RT experiments. We suggest that these models should be validated over a wider range of vessel geometries and operating conditions.     

HYDRODYNAMICS AND MASS TRANSFER IN DOWNFLOW BUBBLE COLUMN

Gas holdup, effective interfacial area and volumetric mass transfer coefficient were measured in two and three phase downflow bubble columns. The mass transfer data were obtained using the chemical method of sulfite oxidation, and the gas holdup was measured using the hydrostatic technique. Glass beads and Triton 114 were used to study the effects of solids and liquid surface tension on the gas holdup and the mass transfer parameters a and k_L a . The gas holdup in three phase systems was measured for non-wettable (glass bead) and wettable (coal and shale particles) solids.

The mass transfer data obtained in the downflow bubble column were compared with the values published for upflow bubble columns. The results indicate that in the range of superficial gas velocities (0.002-0.025) m/s investigated, the values of the mass transfer coefficient were of the same order of magnitude as those observed in upflow systems, but the values of interfacial area were at least two fold greater. Also, the results showed that the operating variables and the physical properties had different influences on a and k_L a in the downflow bubble column. Correlations for a and k_L a for the downflow bubble column are proposed which predict the data with adequate accuracy in the range of operating conditions investigated.     

Gas-liquid mass transfer in trickle-bed reactors: Gas-side mass transfer

New data of gas-liquid mass transfer for cocurrent downflow through packed beds of non-porous particles are presented. Mass transfer parameters for air/carbon dioxide/water and air/carbon dioxide/sodium hydroxide systems were evaluated by least squares fit of the calculated CO₂ concentration profiles in the gas phase to the experimental values. The dependence of k_Ga on gas and liquid flow rates is caused by the dependence of gas-liquid interfacial area, not by the gas-side mass transfer coefficient k_G. In the case of the absorption of dilute carbon dioxide the gas-side resistance is considerably smaller than the liquid-side resistance. In the pulse flow regime, gas-liquid interfacial area calculated from k_La and k_L values obtained by physical, respectively, chemical absorption are lower than the gas-liquid interfacial area evaluated from the measurements under reaction conditions.     

Interfacial Area and Liquid‐Side Volumetric Mass Transfer Coefficient in a Downflow Bubble Column

An experimental investigation was made to measure interfacial area, a, and liquid‐side volumetric mass transfer coefficient, k_La, in a downflow bubble column by chemical methods viz., absorbing CO₂ in aqueous sodium hydroxide and sodium carbonate/bicarbonate buffer solution respectively. The effect of gas and liquid flowrate and nozzle sizes on a and k_La were investigated. The experimental data obtained in the present system were analyzed and correlations were developed to predict a and k_La in terms of superficial gas velocity. The variation of a and k_La with specific power input were shown in graphical plot and compared with other gas‐liquid systems.     

Measurement of mass transfer coefficient in an airlift reactor with internal loop using coalescent and non‐coalescent liquid media

In this work the sulfite oxidation (SOM), dynamic pressure‐step (DPM) and gassing‐out (GOM) methods were compared for volumetric mass transfer coefficient measurement in an airlift reactor with internal loop. As a liquid phase both, non‐coalescent and coalescent media were used. Among the methods discussed here, the mass transfer coefficient (k_La) values obtained by the DPM appear as the most reliable as they were found to be independent of oxygen concentration in the inlet gas, which confirmed the physical correctness of this method. The difference between data measured using air and oxygen was not higher than 10%, which was comparable to the scatter of experimental data. It has been found that the sulfite oxidation method yielded k_La values only a little higher than those obtained by the DPM and the difference did not exceed 10%. Up to an inlet gas velocity (U_GC) of ?0.03 m s^?1 the GOM using oxygen as a gas medium gave k_La values in fact identical with those obtained by the DPM. At higher flows of the inlet gas, the GOM yielded k_La values as much as 15% lower. The enhancement in oxygen mass transfer rate determined in non‐coalescent media was estimated to be up to +15%, when compared with a coalescent batch. The experimental dependence of k_La vs the overall gas hold‐up was described by an empirical correlation. 1 Copyright © 2004 Society of Chemical Industry     

Mass transfer from Taylor bubbles rising in single capillaries

Gas-liquid mass transfer from Taylor bubbles rising in 1, 2 and 3 mm diameter capillaries of circular and square cross-sections was investigated for air-water system. The liquid-phase volumetric mass transfer coefficient k_La was obtained from experimental oxygen absorption dynamics. The experimental k_La values are in good agreement with the model developed by van Baten and Krishna (2004. Chemical Engineering Science 59, 2535-2545), with the additional assumption that the dominant mass transfer contribution is to the film surrounding the bubble.     

Mass transfer characteristics in a gas-liquid reciprocating plate column. I. Liquid phase volumetric mass transfer coefficient

In a series of two papers the results of investigating the mass transfer characteristics of two gas-liquid reciprocating plate columns of the Karr type by different methods are presented. The subject of the first part is a study of the liquid phase volumetric mass transfer coefficient, k_La, while the second part deals with the interfacial area. The volumetric coefficient k_La was investigated using the sulphite method, the pure physical absorption of oxygen, and a dynamic method under culture conditions, the second of these three methods being the most favorable. Very good agreement among these methods was found. Generally, k_La increased with increasing vibration intensity, superficial gas velocity, and the number of perforated plates. Liquid-phase properties appeared to affect k_La only slightly. The coefficient k_La was correlated in terms of the maximum power consumption and the superficial gas velocity:      

Scale Effects on Hydrodynamic and Mass Transfer Characteristics of External Loop Airlift Reactors

Gas hold-up and oxygen transfer have been investigated in two geometrically similar external loop airlift reactors of linear scale ratio of 2. In mass transfer experiments, the sampling location was found to be important as significantly different k_La values can be obtained. The variations of k_La with probe location have been explained in terms of non-uniform hydrodynamic properties and the results obtained have been validated by means of high speed video camera recordings. At higher gas flowrates, the gas hold-up was significantly higher in the large-scale reactor. It was found that in order to maintain the gas hold-up or k_La constant in both the small- and large-scale reactor, the small-scale reactor required 25% and 27% more power input per unit volume of liquid respectively. © 1997 SCI.     

Gas–liquid mass transfer in periodically operated trickle-bed reactors: Influence of the liquid-phase physical properties and flow modulation

The influence of periodic operation on trickle-bed reactor (TBR) hydrodynamics and gas–liquid mass transfer was investigated. Two-phase pressure drop, dynamic liquid hold-up and gas–liquid mass transfer coefficient (k_La) were determined at various liquid flow rates and for different modes of liquid flow variation (increasing and decreasing liquid flow rate). The results reveal the considerable influence of type of liquid flow rate modulation on k_La values (deviations of up to 80% in k_La). Simulation studies on gas-limited reaction in a periodically operated TBR indicate that an enhancement in conversion of about 14% can be expected from an appropriate selection of the operating mode, thus clearly demonstrating the quantitative process intensification feasible through increased gas–liquid mass transfer.     

Influence of recycling on mass transfer and reaction in a G-L jet loop reactor with variable interfacial area

The effect of recycling on mass transfer, characterized by the volumetric mass transfer coefficient k_La, was investigated by absorbing CO₂ into water in a laboratory jet loop reactor. Based on a mathematical model, which includes the correlation function k_La = k_La(r_L), a first order chemical reaction and the variation of interfacial area, a = a(ε_G), caused by strong absorption effects, the interaction ‘recycling – mass transfer – reaction’ was simulated and its influence on the reactor performance is discussed.     

Hydrodynamics,Mass Transfer and Gas Scrubbing in a Co‐current Droplet Column Operating at High Gas Velocities

The main objective of this work was to propose a new process for household fume incineration treatment: the droplet column. A feature of this upward gas‐liquid reactor which makes it original, is to use high superficial gas velocities (13 m s^–1) which allow acid gas scrubbing at low energy costs. Tests were conducted to characterize the hydrodynamics, mass transfer performances, and acid gas scrubbing under various conditions of superficial gas velocity (from 10.0 to 12.0 m s^–1) and superficial liquid velocity (from 9.4·10^–3 to 18.9·10^–3 m s^–1). The following parameters characterized the hydrodynamics: pressure drops, liquid hold‐ups, and liquid residence time distribution were identified and investigated with respect to flow conditions. To characterize mass transfer in the droplet column, three parameters were determined: the gas‐liquid interfacial area (a), the liquid‐phase volumetric mass transfer coefficient (k_La) and the gas‐phase volumetric mass transfer coefficient (k_Ga). Gas absorption with chemical reaction methods were applied to evaluate a and k_Ga, while a physical absorption method was used to estimate k_La. The influence of the gas and liquid velocities on a, k_La, and k_Ga were investigated. Furthermore, tests were conducted to examine the utility of the droplet column for the acid gas scrubbing, of gases like hydrogen chloride (HCl) and sulfur dioxide (SO₂). This is a process of high efficiency and the amount of pollutants in the cleaned air is always much lower than the regulatory European standards imposed on household waste incinerators.     

Mass transfer in liquid-liquid (horizontal) pipeline contactors

The mass transfer characteristics of liquid-liquid (horizontal) pipeline contactors were studied for the bubble and plug flow regimes. The contactors were operated co-currently. The theory of mass transfer with chemical reaction was used to obtain values of physical mass transfer coefficient (k_La) and effective interfacial area (a) for a number of systems. In all the experiments the resistance to mass transfer was confined to the continuous phase. The effect of the flow rates and viscosities of the two phases, interfacial tension, contactor length, pipe diameter, the presence of solids, etc. on both, k_La and a was studied. The values of k_La and a were found to vary from 1 to 50 × 10^?3 sec^?1, and 0.4 to 25 cm^?1, respectively.     

Effect of fluid rheological properties on mass transfer in a bioreactor

Rheological properties and oxygen mass transfer coefficient (k_L a) were investigated in a stirred reactor (10 dm³) in the course of fermentations producing microbial polysaccharides—pullulan and xanthan. The fermentation broths behaved as pseudoplastic non-Newtonian fluids in both cases. Studies on the relationship between fluid rheological properties and k_L a were also carried out. The oxygen mass transfer coefficient decreases during the fermentation and exponential equations have been obtained to describe the relationship between the oxygen mass transfer coefficient, the agitation speed and the apparent viscosity of the broths. Furthermore, comparison of results between pullulan and xanthan fermentations was investigated. For the xanthan fermentation process, mixing and mass transfer in the reactor were more difficult than those for the pullulan fermentation.     

A contribution to the measurement of oxygen mass transfer in a laboratory pressure reactor

A method was used to measure the liquid‐side volumetric coefficient of oxygen mass transfer (k_La) in closed, semi‐batch pressure reactors used in hydrometallurgical laboratories. In this method, the oxygen pressure was monitored as oxygen was continuously sparged into a pressure vessel containing a sodium sulfite solution. A material balance equation was derived for oxygen in the vessel and the experimental data were fitted to this equation. From the constant parameters of the equation, k_La was calculated. The solution in the vessel also contained an appropriate amount of cobalt catalyst so that oxygen was consumed rapidly by oxidation of sulfite to sulfate. Under these conditions, the oxygen concentration in the bulk liquid phase could be assumed to be equal to zero. Values of k_La determined by the method under various conditions were reproduced within 12% deviation from the average values. k_La was found to increase moderately with temperature in the range of 25 to 75 °C, with an activation energy of 33.09 ± 1.33 kJ mol⁻¹. The presence of hydrophobic or hydrophilic solids was found to have a deleterious effect on k_La. © 2000 Society of Chemical Industry     

Oxygen Mass Transfer in Biopharmaceutical Processes: Numerical and Experimental Approaches

Oxygen supply in aerobic bioprocesses is of crucial importance. For this reason, this paper presents the oxygen demand of different cells and summarizes experimental and numerical possibilities for the determination of oxygen transfer in bioreactors. The focus lies on the volumetric oxygen mass transfer coefficient (k_La) calculation using computational fluid dynamics and state-of-the-art models for surface-aerated and forced-aerated bioreactors. In addition, experimental methods for the determination of the k_La value and the gas bubble size distribution are presented.     

Mass Transfer Characteristics of Syngas Components in Slurry System at Industrial Conditions

The gas‐liquid mass transfer behavior of syngas components, H₂ and CO, has been studied in a three‐phase bubble column reactor at industrial conditions. The influences of the main operating conditions, such as temperature, pressure, superficial gas velocity and solid concentration, have been studied systematically. The volumetric liquid‐side mass transfer coefficient k_La is obtained by measuring the dissolution rate of H₂ and CO. The gas holdup and the bubble size distribution in the reactor are measured by an optical fiber technique, the specific gas‐liquid interfacial area aand the liquid‐side mass transfer coefficient k_L are calculated based on the experimental measurements. Empirical correlations are proposed to predict k_L and a values for H₂ and CO in liquid paraffin/solid particles slurry bubble column reactors.