EPR and optical studies on binary mixed alkali-alkaline earth oxide borate glasses doped with Cu<Superscript>2+</Superscript> ions

Mixed alkali alkaline earth oxide borate glasses of the composition (25 – x)Li₂O–xK₂O–12.5BaO–12.5MgO–49B₂O₃–1CuO (x = 0, 5, 10, 15 and 20 mol %) were prepared by the melt quenching technique. The X-ray diffractograms of all the glass samples were recorded at room temperature. Peak free X-ray spectra revealed the amorphous nature of all the prepared glasses. Modulated differential scanning calorimetry (MDSC) was used to determine the glass-transition temperature (T _g ). The probable mixed alkali effect was investigated using experimental techniques like density, molar volume, MDSC, electron paramagnetic resonance (EPR), and optical absorption studies. From the EPR spectra the spin-Hamiltonian parameters were evaluated. The spin-Hamiltonian parameter values indicated that the ground state of \(C{u^{2 + }}is{\kern 1pt} {d_{{x^2} - {y^2}}}\) orbital (²B_1g) and the site symmetry around Cu² is tetragonally distorted octahedral. The variation of g _|| and A _|| as a function of Li₂O content was found to be nonlinear. A broad optical absorption band was observed in all the glasses containing Cu² ions corresponding to ²B_1g → ²B_2g transition. From the optical absorption studies the values of the optical band gap (E _opt) for indirect, direct transitions and Urbarch energy (ΔE) have been evaluated. By co-relating the EPR and optical absorption data, bonding parameters α², β² and β ₁ ² were evaluated.     

Physical Properties,Optical band gaps and Radiation Shielding Parameters Exploration for Dy<Superscript>3+</Superscript>-doped Alkali/Mixed Alkali Multicomponent Borate Glasses

Six compositions of 1 mol % Dy³⁺-doped multicomponent borate glasses containing single Li₂O, Na₂O, K₂O and mixed Li₂O–Na₂O, Li₂O–K₂O, and Na₂O–K₂O oxides have been synthesized by well-known melt-quenching technique. Following the measured density and refractive index values, various physical parameters were estimated for all the glass samples and differences in them are correlated with structural changes. To explore optical properties like absorption edge (λ_cut-off), optical band gap energy (E_opt), and Urbach energy (ΔE), optical absorption spectra were recorded for all the glasses. The E_g has been calculated using Davis and Mott theory for direct allowed, and indirect allowed transitions and the results were reported. The E_g values are also estimated using absorption spectrum fitting (ASF) method. The optical parameters variations have also been associated with the structural changes occurring in the glasses with different alkali/mixed alkali oxides content presence. The shielding properties of the prepared glasses were studied in terms of effective atomic numbers (Z_eff), mean free path (MFP), half value layer (HVL) and macroscopic effective removal cross-section (Σ_R). From these results, it was found that Potassium (K) glass shows superior gamma ray shielding properties due to a higher value of Z_eff and lower values of both MFP and HVL. These results indicate that the prepared glasses might be utilized in place of some common shielding materials to shield γ-rays and neutrons.     

Optical,Spectral, and Radiation-Shielding Properties of High-Lead Phosphate Glasses

The spectral, optical, physicochemical, radiative, and radiation-shielding properties of glasses in the PbO-P₂O₅-R _m O _n system (where R _m O _n stands for Group I–V element oxides) are investigated as a function of their composition. The composition of a colorless radiation-resistant high-lead glass suitable for production on a semicommercial scale is determined. The properties and optical quality parameters of the glass are studied. The new phosphate glass is a lead metaphosphate containing aluminum, alkali, and alkaline-earth oxides. This glass is resistant to radiation at doses up to 10⁷ R and has an optical transmission edge at 360 nm. The coefficient of absorption of gamma radiation for the new glass is larger than those of dense silicate flints. According to the optical parameters, the new glass lies between dense flints and dense barium flints in the Abbe diagram and compensates for the absence of the latter flints in catalogues of radiation-resistant glasses.     

Effect of nitrogen to niobium atomic ratio on superconducting transition temperature of δ-NbN<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> powders

Powders of cubic niobium nitride δ-NbN _x with a particle size of below 20 μm were prepared by reactive diffusion at T = 1455?1475°C under nitrogen pressures of P ₁(N₂) = 0.1?3 MPa and P ₂(N₂) = 25 MPa. For these powders, the values of the stoichiometric coefficient x, lattice parameter a, and the superconducting transition temperature Tc were measured and the a(x), T _c(x) and T _c(a) functions were analyzed. The T _c values were found to linearly grow with increasing a (decreasing structure imperfection). A maximum value of T _c (15.8 K) corresponded to a maximum value of a (4.3934 Å). Maximain the a(x) and T _c(x) curves were found to correspond to a slightly substoichiometric nitride with x = 0.98. Having synthesized cubic niobium nitrides with 0.892 < x < 1.062, we managed to measure the dependences of a and T _c on x all over the almost entire homogeneity range for δ-NbN _x . Our a(x) and T _c(a) functions were found to reasonably agree with those previously reported for SHS-produced δ-NbN _x powders.     

Thermogravimetric characteristics of <Emphasis Type="Italic">α</Emphasis>-cellulose and decomposition kinetics in a micro-tubing reactor

The pyrolysis characteristics and kinetics of α-cellulose were investigated using thermogravimetric analyzer (TGA) and micro tubing reactor, respectively. Most of the α-cellulose decomposed between 250 and 400 °C at heating rate of 5–20 °C/min. The apparent activation energy was observed in the range of 263.02 kJ mol^?1 to 306.21 kJ mol^?1 at the conversion of 10-80%. The kinetic parameters were determined by nonlinear least-squares regression of the experimental data, assuming first-order kinetics. It was found from the kinetic rate constants that the predominant reaction pathway was A(α-cellulose) to B(bio-oil) rather than A(α-cellulose) to C(gas; C₁-C₄) and/or to B(bio-oil) to C(gas; C₁-C₄) at temperatures of 340-360 °C.     

Photon interaction parameters for some ZnO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Some photon interaction parameters such as mass attenuation coefficient, effective atomic number, half value layer, mean free path and electron density for 15ZnO–(17.5–x)Al₂O₃–xFe₂O₃–67.5P₂O₅ glass system (x = 0, 7.5, 12.5, 17.5) and 15ZnO–(25–x)Al₂O₃–xFe₂O₃–60P₂O₅ glass system (x = 0, 25) have been investigated in the photon energy range of 1 keV to 100 GeV. It has been observed that all the photon interaction parameters for the selected glass systems vary with the photon energy. Among the selected glass systems, the sample 15ZnO–25Fe₂O₃–60P₂O₅ glass system shows maximum values for mass attenuation coefficients, effective atomic numbers, electron densities and minimum values for mean free path and half value layer in the entire energy grid.     

Structure,stability and optical parameters of cobalt zinc borate glasses

In this study, the impact of cobalt oxide (CoO) on the structure, stability, linear and nonlinear optical parameters of B₂O₃–Na₂O–ZnO glasses was scrutinized. A series of glass system (ZnCoNaB-glasses) was successfully prepared through the melt quenching approach. Optical absorbance, reflectance, transmittance and FTIR spectroscopy were performed for all ZnCoNaB-glasses. The FTIR results showed that the BO₄ units are enhanced while nonbridging oxygens are decreased with further CoO addition. Furthermore, ZnO exists as four-coordinated [ZnO₄] units and these units decreased with further doping of CoO. These structural variations produce a decreasing impact in Urbach energy and nonlinear refractive index, meanwhile enhance the glass stability. Further, the metallization criterion (M) values indicate that our glass samples can be used for a new generation of nonlinear optical glasses. The preceding results can predict that the investigated ZnCoNaB-glasses will be utilized in versatile applications; especially optical switching and computing.     

Solid Solution (AlN)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>(SiC)<Subscript>1–<Emphasis Type="Italic">x</Emphasis></Subscript> (<Emphasis Type="Italic">x</Emphasis> ≈ 0.7) by SHS under High Pressure of Nitrogen Gas

Solid solution (AlN) _x (SiC)_1–x (x = 0.7) was prepared from Al–SiC mixtures by SHS under high pressure of nitrogen gas (50, 70 MPa) and characterized by XRD and SEM. Combustion product was found to have a wurtzite 2H structure with lattice parameters a = 3.10889 ± 0.00022 Å and c = 5.00741 ± 0.00080 Å.     

Effect of iron oxide (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>) on the structural,optical, electrical,and dielectric properties of SrO–V<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

The oxide glass system of the composition (10 – x)SrO–xFe₂O₃–90V₂O₅, (x = 0, 2, 4, 6 and 8 mol %) were prepared by a standard melt quenching technique. The amorphous nature of the prepared glass was confirmed using X-ray diffraction technique. The infrared spectra of these glasses were recorded over a continuous spectral range (850–1500 cm^–1). The density of prepared sample was obtained by the Archimedes principle. The physical parameters of the glasses were also determined with respect to the composition. Density increases from 3.10 to 3.20 g/cm³, whereas the molar volume decreases with the increase in Fe₂O₃ concentration. In order to study optical properties, absorption spectra were measured at room temperature. Indirect optical energy band gap, optical dielectric constant, refractive index were calculated from optical energy band gap. The refractive index decreases gradually with the increase in Fe₂O₃ content due to increase of bridging oxygen’s. For temperatures from 300 to 500 K, the dc conductivity increased with the increasing Fe₂O₃ content. The dielectric properties like dielectric constant, dielectric loss factor and dielectric loss tangent investigated at the room temperature in the frequency range of 10 kHz to 1 MHz decreases with frequency. The dielectric behavior shows strong frequency as well as composition dependence.     

Effect of the 3<Subscript>d</Subscript>-Transition Metal Oxides on the Surface Tension of the Sodium Silicate Melt

The effect of 3d-transition metal oxides on the surface tension of the 17.5Na₂O · 82.5SiO₂ · nRO (R = Mn, Fe, Co, Ni, Cu; n = 0.1–10) melt is revealed in the temperature range 1250–1450°C. It is found that cobalt oxide in the range of low concentrations (0.1–1.0 mol %) is characterized by anomalously low values of the surface tension. In the case of CoO oxide, the surface tension increases as the temperature increases and the melts containing MnO, FeO, NiO, and CuO oxides have negative temperature coefficients. In the range of high concentrations of the studied oxides (n = 10 mol %), the surface tension of melts decreases with an increase in the atomic number of cation in the sequence Mn → Fe → Co → Ni → Cu.     

Dielectric study of side-chain liquid crystalline polyazomethine/fullerene C<Subscript>60</Subscript> nanocomposite

For side-chain liquid crystalline polyazomethine/fullerene C₆₀ nanocomposite (C₆₀ loading is 0.25 wt%), both real and imaginary components of the dielectric permittivity were investigated in wide regions of temperature and frequency. Analysis of frequency dependent permittivity allowed finding three relaxations (α, β ₁ and β ₂) in the nanocomposite. They were attributed to specific modes of molecular mobility. β-relaxations were described with the Arrhenius equation, whereas α-relaxation was described with the Vogel-Fulcher-Tammann equation. Anti-plasticization effect of the C₆₀ doping was shown to be manifested as an increase of the glass transition temperature of the nanocomposite as compared with that of the neat polymer.     

Raman spectra and surface structure of CaO-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass leached in potassium hydroxide solutions

It is difficult to research on the surface structure of amorphous phase in fly ash during leaching reaction due to crystalline phase and complex structure. In the present work, in order to reveal the effects of leaching reaction on the surface structure of amorphous phase in fly ash, the modelling CaO-Fe₂O₃-Al₂O₃-SiO₂ glass was prepared by the traditional melting methods. The leaching reaction of CaO-Fe₂O₃-Al₂O₃-SiO₂ glass with 7.5 M KOH was investigated by spectroscopy, spectrophotometer and wet chemical method. The results show that the content of Q ¹, Q ², Q ³ and Q ⁴ of glass without corrosion was 4.21, 9.51, 23.03 and 52.55%, respectively, which shows that the network polymerization of glass is compact. The leaching reaction of glass can be described by the following equation: dS/dt = k/(r + S ₀). Leaching in KOH for various times induces the content of Q ⁴ and Q ¹ to be decreased, and Q ² and Q ³ increased, resulted in the depolymerization of network and the surface glass dissolved in alkaline solution to form a gel phase. In stage one of leaching reaction, the rate of iron ion leached from glass surface was slow, which resulted in the small slope of straight-line relationship of leaching curve. In the following stage, the leaching rate of iron ion increased with the prolongation of time.     

Parameters of luminescence and the local structure of Eu<Superscript>3+</Superscript> centers in fluorogermanate glasses

The influence of the chemical nature of the local environment of Eu³⁺ ions on the parameters of luminescence of these centers in glasses of the (BaGeO₃)_{1 ? x ? y} (Al₂O₃) _x (0.45CaF₂ · 0.55MgF₂) _y (x = 0.25, y = 0; x = 0.17, y = 0.17; x = 0.15, y = 0.22; x = 0.07, y = 37.00; x = 0, y = 0.45) system is investigated. The oxidation state of europium atoms and the degree of homogeneity of their local environment in the glasses are determined using ¹⁵¹Eu Mössbauer spectroscopy.     

Change of the thermal behavior of 55Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> ⋅ 45B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass at annealing close to the vitrification temperature

The characteristic properties of relaxation processes for 55Bi₂O₃ ? 45B₂O₃ glass were described. The pattern of changes of the vitrification temperature (T _g ) is found to be quasi-periodic; the value of the endothermic effect near T _g (ΔC’ _p ) and the difference between the softening point and the vitrification temperature (T _m –T _g ) were determined. The temperature-time parameters of the transition from quasi-periodic to the continuous change of the properties were determined and an explanation of such behavior of the system was offered.     

SHS-produced Co<Superscript>2+</Superscript>Ti<Superscript>4+</Superscript>-doped barium and strontium hexaferrites: Static and dynamic magnetic properties

Static and dynamic magnetic properties of SHS-produced BaFe_12–2x (Co _х Ti _х )O₁₉ (х = 1.0, 1.1, 1.2) and SrFe_12–2y (Co _y Ti _y )O₁₉ (0 ≤ y ≤ 1.0) hexaferrites were characterized by magnetization and FMR measurements. Dynamic properties of SrFe_12–2y (Co _y Ti _y )O₁₉ hexaferrites were rationalized in terms of not only magnetic anisotropy but also the anisotropy of magnetomechanical ratio. SHS-produced ferrites can be recommended for designing radar-absorbent coatings and other SHF devices operating in the range 20–50 GHz.     

Physical and Mechanical Properties of Neodymium Doped Zinc Borate Glass with Different Boron Content

A zinc borate glass system of composition xNa₂O-(58-x)B₂O₃-40ZnO-2Nd₂O₃(where x = 0, 5, 10, 15, 20 and 25) has been prepared using the melt quenching method. The effect of Na₂O on the crystal structure, density, molar volume and mechanical properties was investigated. X-ray diffraction analysis confirmed the amorphous nature of the prepared glass. The density and molar volume followed the normal behavior of a glass system. Ultrasonic non-destructive testing was employed for measuring the mechanical properties of the zinc borate glass system. The values of Young’s modulus and the Poisson ratio decreased with increasing the Na ⁺ concentration. Meanwhile, the microhardness, Debye temperature and acoustic impedance were diminished with increasing the Na ⁺ ion content. The results showed that the ultrasonic non destructive test measured the mechanical properties of the glass with similar accuracy to the Vickers microhardness. Such tested properties can be applied for silicate and non-silicate glasses.     

Thermal properties and crystallization behaviors of polylactide/redwood flour or bamboo fiber composites

A series of polylactide/redwood flour (PLA/RWF) and polylactide/bamboo fiber (PLA/BF) composites were successfully prepared using a solution mixing procedure. Fourier transform infrared spectroscopy (FTIR) and wide-angle X-ray diffraction (XRD) were employed to characterize these composites. Thermal properties and crystallization behaviors of PLA composites were determined by their respective techniques of differential scanning calorimetry (DSC) and polarized optical microscopy (POM). With the increasing content of fibers, the glass transition temperature (T _g ), crystallization temperature (T _c ), and melting temperature (T _m ) of PLA/RWF composites decreased first and then increased, but T _g and T _m of PLA/BF composites increased first and decreased afterwards. It is suggested that fibers could improve the segmental mobility of PLA; meanwhile, the different morphologies, sizes, and densities of RWF and BF have different effects on thermal properties of composites. Under the increasing content of RWF, the crystallization rate of the composite increased first and decreased afterwards. When the content of RWF was 5%, the crystallization rate was at its maximum. It could be possible that the addition of fibers was able to nucleate PLA and increase the degree of crystallinity, but the excess content of fibers easily led to heterogeneous composites and subsequent poor crystallization behaviors. In a word, thermal properties and crystallization behaviors of PLA composites were regularly changing by increasing content of fibers.     

Temperature and Pressure Dependence of Elastic Constants and Related Parameters for InP Semiconductor

Based on the empirical pseudo-potential method (EPM), the symmetric and anti-symmetric pseudo-potential form factors have been adjusted to match the calculated energy gaps of InP with the corresponding experimental values. The adjusted symmetrical and anti-symmetrical form factors at G(1,1,1) have been used to calculate the polarity of the considered material. The elastic constants C ₁₁, C ₁₂ and C ₄₄ of InP have been obtained. The knowledge of these constants helps us to determine their related elastic parameters such as bulk (B _u ), shear (C _s ) and Young’s (Y ₀) moduli. Other important parameters such as Poisson’s ratio (σ ), linear compressibility (C ₀ ), Cauchy ratio (C _a ) , Born ratio (B ₀), isotropy factor (A ), bond stretching (α ), bond binding force (β ) and internal strain parameter (ζ ) for InP have also been calculated. The variation of all studied quantities with temperature and pressure has been investigated. Our results show a good agreement with the available experimental data. Most of our data may be taken as references especially for high values of temperature and pressure.     

Effect of the Molecular Structure on the Adsorption Properties of Cationic Surfactants at the Air–Water Interface

The surface activity and thermodynamic properties of adsorption at the air–water interface of two series of cationic surfactants based on isourea: the O-dodecyl-N,N′-diisopropylisourea hydrochloride, hydrobromide, and hydroiodide and the O-tridecafluorooctyl-N,N′-diisopropylisourea hydrochloride and hydrobromide were studied. The effect of structural parameters as the nature of the halide counter ion and the nature of the non-polar chain on the surface activity and thermodynamic properties of adsorption were investigated. The surface parameters, the maximum surface excess concentration (Γ _max), the minimum area per molecule (A _min) at the aqueous solution-air interface, effectiveness of surface tension reduction (π_CMC), and efficiency of surface tension reduction (pC ₂₀) were estimated. The standard Gibbs free energy of adsorption, (ΔG°_ads) change has been calculated at different temperatures.     

Ultrasonic velocity measurements in isobutyric acid - water binary mixtures over the temperature range from 300.15 to 313.15 K

We measured the ultrasonic velocity, U, density, ρ, and viscosity, η in Isobutyric acid - water binary liquid mixtures over the entire composition range at temperatures ranging from 300.15 to 313.15 K under atmospheric pressure. The experimental data values were analyzed to determine, various acoustical parameters: adiabatic compressibility, β, acoustic impedance, Z, free length, L_f, free volume, V_f, molar volume, V_m, relaxation time, τ, absorption coefficient, α/f², internal pressure, π_i, Gibb’s free energy, ΔG, cohesive energy, CE, Wada’s constant, W, Rao’s constant, R_m and relative association, R_A. The variation of these parameters versus the mixture composition was explained on the basis of the intermolecular interactions between the components of the mixture.