Comparison on photocatalytic degradation of gaseous formaldehyde by TiO2, ZnO and their composite

In order to compare the photocatalytic properties of TiO₂, ZnO and their composite in the gas phase pollutant environment, nanocomposite with different mole ratios of TiO₂/ZnO were designed to degrade gaseous formaldehyde. The results showed that the rate constant of TiO₂ for formaldehyde degradation was 0.05 min^?1 which was two orders of magnitude larger than that of ZnO in our experiment. Through comprehensive analysis of UV–vis diffuse reflectance (UV–vis) spectra, photoluminescence spectra (PL) and energy band diagram, it was found that the differences of photocatalytic properties between ZnO and TiO₂ may mainly originate from the increased recombination of photoinduced charges in ZnO. The photocatalytic properties of TiO₂/ZnO composite for formaldehyde degradation were much worse than those of TiO₂, while better than those of ZnO. The addition of a small amount of ZnO weakened the photocatalytic properties of TiO₂. It may be attributed to that the recombination action of photoinduced electron–hole pairs in ZnO.     

Antibacterial and photocatalytic active transparent TiO2 crystallized CaO–BaO–B2O3–Al2O3–TiO2–ZnO glass nanocomposites

Transparent TiO₂ crystallized 5CaO–10BaO–65B₂O₃–Al₂O₃–20TiO₂–10ZnO (CBBATZ) glass nanocomposites were fabricated using melt-quenching technique followed by specific heat treatments. As-quenched glass samples were provided three different heat treatments at 630°C for 3, 5, and 10 hours in order to obtain different amounts of TiO₂ nanocrystals in the glass. The presence of rutile phase of TiO₂ nanocrystals in glass was confirmed by X-ray diffraction. The glass nanocomposite heat treated for 10 hours showed a hydrophobic nature with contact angle of 90.90°. Contact angle decreased from 90.90 to 22.20°, when irradiated under ultraviolet (UV) radiation for 45 minutes. This photoinduced hydrophilicity showed a photocatalytic and self-cleaning properties of glass nanocomposite. During photocatalytic ink test, the maximum change in color of Resurin (Rz) ink and 60% degradation in absorbance of ink within 150 minutes under UV radiation were found for glass nanocomposite heat treated at 10 hours. Also, 78% degradation in absorbance of methylene blue dye (pollutant) within 180 minutes under UV irradiation was found for glass naocomposite heat-treated at 10 hours. Antibacterial performance of transparent glass nanocomposite against Escherichia coli was evaluated as well. More than 95% of the bacterial cells were degraded with glass nanocomposite heat-treated at 10 hours. CBBATZ glass nanocomposite found to impart the antibacterial effect through generation of reactive oxygen species (ROS) in aqueous medium. ROS species which was confirmed in the bacterial cell through intracellular ROS generation kit. During evaluation of mechanical properties using nanoindentation technique, the values of hardness and reduced modulus increased by ~26% and 10%, respectively, for glass nanocomposite heat-treated at 10 hours as compared to as-quenched glass.     

A novel approach for the synthesis of highly active ZnO/TiO2/Ag2O nanocomposite and its photocatalytic applications

The present work is focused on the preparation of hybrid ZnO/TiO₂/Ag₂O nanocomposite for enhanced photocatalytic activity. The resultant samples are characterized by using XRD, SEM, EDX, HR-TEM, UV-DRS, BET and XPS techniques. X-ray diffraction analysis indicates the co-existence of wurtzite, anatase and cubic phases in ZnO/TiO₂/Ag₂O nanocomposite. The band gap energy value of the photocatalyst is 3.39 eV, which has been evidenced from UV–visible diffuse reflectance spectroscopy measurements. Photocatalytic degradation of methylene blue dye has been investigated by using UV–visible spectrophotometer. From the result, it has been concluded that ZnO/TiO₂/Ag₂O nanocomposite has proven to be an efficient photocatalyst under UV irradiation when compared to that of mono and binary oxide systems. Further, the possible photodegradation mechanism is proposed to support the enhancement of photocatalytic activity towards degradation of dyes.     

Doped 1D Nanostructures of Transition-metal Oxides: First-principles Evaluation of Photocatalytic Suitability

The splitting of water molecules under the influence of solar light on semiconducting electrodes is a clean and renewable source for the production of hydrogen fuel. Its efficiency depends on the relative position of the band-gap edges or the induced defect levels with a proper band alignment relative to the redox H⁺/H₂ and O₂/H₂O potentials. For example, TiO₂ and ZnO bulk, as well as thick slabs (whose band gaps are ∼3.2–3.4 eV), can be active only for photocatalytic applications under UV irradiation (possessing ∼1 % solar energy conversion efficiency). Nevertheless, by adjusting the band gap through formation of nanostructures and further doping, the efficiency can be increased up to ∼15 % (for 2.0–2.2 eV band gap). We analyse results of DFT (density functional theory) calculations on TiO₂ nanotubes and ZnO nanowires, both pristine and doped (e.g., by Ag_Zn, C_O, Fe_Ti, N_O and S_O substitutes). To reproduce the energies of one-electron states better, we have incorporated the Hartree-Fock (HF) exchange into the hybrid DFT+HF Hamiltonian. Both the atomic and electronic structure of nanomaterials, simulated by us, are analysed to evaluate their photocatalytic suitability, including positions of the redox potential levels inside the modified band gap, the width of which corresponds to visible-light energies. Analysis of the densities of states (DOS) for considered nanostructures clearly shows that photocatalytic properties can be significantly altered by dopants. The chosen hybrid methods of first-principles calculations significantly simplify selection of suitable nanomaterials possessing the required photocatalytic properties under solar light irradiation.     

Photocatalytic oxidative desulfurization of dibenzothiophene catalyzed by amorphous TiO2 in ionic liquid

Three types of TiO₂ were synthesized by a hydrolysis and calcination method. The catalysts were characterized by X-ray powder diffraction (XRD), diffuse reflectance spectrum (DRS), Raman spectra, and X-ray photoelectron spectroscopy (XPS). The XRD and Raman spectra indicated that amorphous TiO₂ was successfully obtained at 100 °C. The results indicated that amorphous TiO₂ achieved the highest efficiency of desulfurization. The photocatalytic oxidation of dibenzothiophene (DBT), benzothiophene (BT), 4,6-dimethyldibenzothiophene (4,6-DMDBT) and dodecanethiol (RSH) in model oil was studied at room temperature (30 °C) with three catalysts. The system contained amorphous TiO₂, H₂O₂, and [Bmim]BF₄ ionic liquid, ultraviolet (UV), which played vitally important roles in the photocatalytic oxidative desulfurization. Especially, the molar ratio of H₂O₂ and sulfur (O/S) was only 2: 1, which corresponded to the stoichiometric reaction. The sulfur removal of DBT-containing model oil with amorphous TiO₂ could reach 96.6%, which was apparently superior to a system with anatase TiO₂ (23.6%) or with anatase — rutile TiO₂ (18.2%). The system could be recycled seven times without a signicant decrease in photocatalytic activity.     

Fabrication of high-efficiency anatase TiO2 photocatalysts using electrospinning with ultra-violet treatment

In metal oxide nanofiber fabrication using the electrospinning method, heat treatment is performed at temperatures of 500°C or higher for crystallization and polymer desorption. Therefore, it is difficult to fabricate low-temperature phase metal oxides that crystallize at low temperatures. TiO₂, a representative metal oxide often used as photocatalysts, is known to have higher photocatalytic activity in the low-temperature phase (anatase structure) than in the high-temperature phase (rutile structure). Studies on the fabrication of TiO₂ anatase nanofibers using conventional electrospinning have reported disadvantages such as the partial expression of rutile structures and low crystallinity. This study developed an anatase TiO₂ nanofiber as a high-efficiency catalyst based on the electrospinning method and a residual organic matter cleaning method that employs ultra-violet (UV) light. We fabricated nanofibers using the electrospinning method and implemented TiO₂ nanofibers with the anatase structure through heat treatment at 260°C. Residual organics remaining after heat treatment of the fabricated crystalized TiO₂ nanofibers were removed by exposing them to UV light, thereby improving photocatalytic efficiency. The photocatalytic efficiency of the fabricated TiO₂ nanofibers was confirmed through a methylene blue (MB) decomposition experiment under visible light irradiation. The photocatalytic efficiency (time taken for the concentration of the MB solution to reach 50%) of the UV-treated TiO₂ nanofibers was approximately six times higher than of P25 and the heat-treated nanofibers.     

Spherical activated carbon as an enhanced support for TiO2/AC photocatalysts

Titanium dioxide nanoparticles prepared in situ by sol–gel method were supported on a spherical activated carbon to prepare TiO₂/AC hybrid photocatalysts for the oxidation of gaseous organic compounds. Additionally, a granular activated carbon was studied for comparison purposes. In both types of TiO₂/AC composites the effect of different variables (i.e., the thermal treatment conditions used during the preparation of these materials) and the UV-light wavelength used during photocatalytic oxidation were analyzed. The prepared materials were deeply characterized (by gas adsorption, TGA, XRD, SEM and photocatalytic propene oxidation). The obtained results show that the carbon support has an important effect on the properties of the deposited TiO₂ and, therefore, on the photocatalytic activity of the resulting TiO₂/AC composites. Thus, the hybrid materials prepared over the spherical activated carbon show better results than those prepared over the granular one; a good TiO₂ coverage with a high crystallinity of the deposited titanium dioxide, which just needs an air oxidation treatment at low-moderate temperature (350–375 °C) to present high photoactivity, without the need of additional inert atmosphere treatments. Additionally, these materials are more active at 365 nm than at 257.7 nm UV radiation, opening the possibility of using solar light for this application.     

Photocatalytic degradation of Brilliant Red M5B using four different nanocomposites (ZnFe2O4, porous ZnFe2O4, ZnFe2O4–TiO2, FeTiO3) coated on glass

This paper presents the preparation, characterization, and application of four different nanocomposites in photocatalytic degradation of the Brilliant Red M5B as a dye contaminant. Nanocomposites include ZnFe₂O₄, porous ZnFe₂O₄, ZnFe₂O₄–TiO₂, and FeTiO₃ prepared and coated on a glass slide by doctor blade method. Different techniques to characterize composites are X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and diffuse reflectance spectra (DRS). FESEM shows that nanocomposites are nanocrystallines and a narrow dispersion in size. XRD confirms that the prepared nanocomposites are composed of ZnFe₂O₄, FeTiO₃ and TiO₂. Degradation efficiency of composites is evaluated using Brilliant Red M5B as a model pollutant under UV irradiation with homemade photocatalytic apparatus. The results showed that the photocatalytic efficiency of ZnFe₂O₄–TiO₂ is higher than that of other photocatalyst, which is mainly ascribed to ZnFe₂O₄ NPs with the spinel structure.     

Photocatalytic enamel/TiO2 coatings developed by electrophoretic deposition for methyl orange decomposition

The aim of this study was to obtain photocatalytic coatings, capable to decompose organic pollutants, through Electrophoretic Deposition (EPD) of enamels containing respectively 0%, 5%, 10%, 15% (in wt%) of TiO₂ onto carbon steel substrates. High quality and homogeneous coatings were obtained by applying 12.5?V during 10?s, as the best EPD conditions. The layers were subsequently heat treated at 740?°C for 10?min, in order to obtain dense glazes.Rietveld refinement of XRD patterns and Raman results show that, after the heat treatment at 740?°C, TiO₂ mostly exists as anatase, responsible of the photocatalytic effect. Semi-quantitative chemical analysis indicate segregation of TiO₂ on the coatings surface, reaching saturation in the sample with 10?wt% TiO₂. FEG-SEM observations reveal rod-like and spherical Ti-rich phases along the cross section of the coatings; some Ti was also dissolved into the enamel. 3D topographical mapping shows that, by adding TiO₂, surface roughness increases significantly.Photocatalytic tests were carried out using a 2?×?10^?5 M aqueous solution of Methyl Orange (MO) as an organic pollutant. By comparing the decomposition rate of MO achieved with the pure enamel (0% of TiO₂) and with the sample with 10% of TiO₂, it was shown that the addition of 10% of TiO₂ results in 90% photocatalytic efficiency.Moreover, the permeation of organic compounds and their UV degradation were studied by measuring the water contact angle onto the enamel surface directly after dipping into oleic acid and after various UV irradiation times. The longer the UV irradiation time, the lower the contact angle, down to a minimum of 14.54° after 8?h of UV irradiation. This means, the compound was initially adsorbed on the enamel/TiO₂ coating surface (10?wt% TiO₂) but was efficiently decomposed upon UV irradiation.     

The degradation of an azo dye in a batch slurry photocatalytic reactor

The photocatalytic degradation of a commercial azo-reactive textile dye, Remazol Red F-3B, has been investigated in a batch slurry reactor using semiconductor catalysts like, ZnO and TiO₂, and two UV sources emitting mainly at 254 and 365 nm. Non-irradiated catalysts and non-catalyzed UV irradiation have negligible effect on the dye degradation. Initial pH, dye concentration, light power and catalyst loading as well as the catalyst type and UV wavelength are considered as process variables. The results showed that decolorization and TOC removal efficiencies of ZnO are higher under 365 nm UV. On the other hand, when two photocatalysts are compared, the decolorization performance of ZnO is higher than TiO₂ under 365 nm UV_, while TiO₂ performs better under 254 nm UV. Furthermore, from the TOC removal point, TiO₂ performs better than ZnO irrespective of the UV wavelength. TiO₂ irradiated under 254 nm UV degrades successfully both benzene and naphthalene derivatives.     

Spray pyrolysis synthesis of mesoporous TiO<Subscript>2</Subscript> microspheres and their post modification for improved photocatalytic activity

Mesoporous TiO₂ microspheres were prepared by spray pyrolysis for photocatalysis. Post modification of TiO₂ by heat treatment was performed to optimize its photocatalytic performance. First, spherical TiO₂ particles with mesoporous structure were synthesized at pyrolysis temperatures of 500, 600, and 700 °C. After characterization by XRD, SEM, and N₂ adsorption, a sample prepared at 500 °C was found to possess desirable properties for photocatalytic performance through post-modification. In methylene blue degradation, mesoporous TiO₂ microspheres synthesized at 500 °C outperformed other microspheres. Furthermore, samples obtained by spray pyrolysis at 500 °C were calcined at various temperatures as a post-modification process. The sample calcined at 350 °C showed improved photocatalytic activity due to optimal anatase crystallinity and surface area.     

Synthesis of heterostructured Bi2O3–CeO2–ZnO photocatalyst with enhanced sunlight photocatalytic activity

The development of heterostructured semiconductor photocatalysts makes a noteworthy advancement in environmental purification technology. In this work, a novel heterostructured Bi₂O₃−CeO₂−ZnO, fabricated by a combination of microwave-assisted hydrothermal and thermal decomposition methods, showed an enhanced photocatalytic activity for Rhodamine B (RhB) degradation under sunlight, as compared to pristine ZnO, Bi₂O₃, CeO₂, and commercial Degussa TiO₂-P25. The obtained products were thoroughly characterized by various techniques including X- ray powder diffraction (PXRD), field emission scanning electron microscopy (FE-SEM), elemental color mapping, energy-dispersive X-ray spectroscopy (EDAX), Raman spectrometry, Fourier transform infrared (FT-IR) spectroscopy, UV–visible diffuse reflectance spectroscopy (UV–vis DRS), and photoluminescence (PL) spectroscopy. PXRD analysis reveals that the heterostructure has the monoclinic lattice phase of α-Bi₂O₃, the cubic phase of CeO₂ and the hexagonal wurtzite phase of ZnO. FE-SEM images show that Bi₂O₃−CeO₂−ZnO has an ordered mixture of nanorod and nanochain structures. EDAX, elemental color mapping, Raman and FT-IR analyses confirm the successful formation of the heterostructured Bi₂O₃−CeO₂−ZnO. The UV–Vis DRS results demonstrate that Bi₂O₃−CeO₂−ZnO exhibits wide visible-light photoabsorption in 400–780 nm range. Moreover, the reduction in PL intensity of the heterostructured Bi₂O₃−CeO₂−ZnO, when compared to the pristine Bi₂O₃, CeO₂, and ZnO, indicates enhanced charge separation. The study on the mechanism displayed that the improved photocatalytic activity of Bi₂O₃−CeO₂−ZnO could be attributed to (1) the efficient separation of photoinduced electrons and holes of the photocatalysts, caused by the vectorial transfer of electrons and holes among ZnO, CeO₂ and Bi₂O₃, and (2) the wide visible-light photoabsorption range. This study introduces a new class of promising sunlight-driven photocatalysts.     

Facile fabrication of TiO2-SiO2-C composite with anatase/rutile heterostructure via sol-gel process and its enhanced photocatalytic activity in the presence of H2O2

Constructing anatase/rutile heterostructure in TiO₂ based materials is a quite powerful approach to enhance their photocatalytic activities. Herein, by simply annealing the sol-gel derived TiO₂-SiO₂ composite in N₂ atmosphere at 850 °C, TiO₂-SiO₂-C composite (CTS-850) with anatase/rutile heterostructure has been successfully prepared, while the counterpart prepared in air contains only anatase phase. It was proven that the residual organic groups in the sol-gel process were converted into carbon species upon N₂ annealing, during which TiO₂ in the composite was partially reduced, not only leaving lots of oxygen vacancies on its surface but also promoting the phase transformation. By turning the annealing temperature and atmosphere, a series of control products were further synthesized. Among these samples, the CTS-850 showed the best photocatalytic performance toward Rhodamine B degradation in the presence of H₂O₂, which was mainly due to its lowest band gap and the enhanced sensitization of H₂O₂ by oxygen vacancies. Moreover, the photocatalytic activity of CTS-850 remained unchanged after five cycles and a proper mechanism was also proposed.     

Photocatalytic decomposition of NO on titanium oxide thin film photocatalysts prepared by an ionized cluster beam technique

Transparent TiO₂ thin film photocatalysts were prepared on transparent porous Vycor glass (PVG) by an ionized cluster beam (ICB) method. The UV‐VIS absorption spectra of these films show specific interference fringes, indicating that uniform and transparent TiO₂ thin films are formed. The results of XRD measurements indicate that these TiO₂ thin films consist of both anatase and rutile structures. UV light (λ > 270 nm) irradiation of these TiO₂ thin films in the presence of NO led to the photocatalytic decomposition of NO into N₂, O₂ and N₂O. The reactivity of these TiO₂ thin films for the photocatalytic decomposition of NO is strongly dependent on the film thickness, i.e., the thinner the TiO₂ thin films, the higher the reactivity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Gas‐Phase Hydrogenolysis of Glycerol Catalyzed by Cu/MOx Catalysts

The catalytic activities of Cu/MO_x (MO_x = Al₂O₃, TiO₂, and ZnO) catalysts in the gas‐phase hydrogenolysis of glycerol were studied at 180–300 °C under 0.1 MPa of H₂. Cu/MO_x (MO_x = Al₂O₃, TiO₂, and ZnO) catalysts were prepared by the incipient wetness impregnation method. After reduction, CuO species were converted to metallic copper (Cu⁰). Cu/Al₂O₃ catalysts with high acidity, high specific surface areas and small metallic copper size favored the formation of 1,2‐propanediol with a maximum selectivity of 87.9 % at complete conversion of glycerol and a low reaction temperature of 180 °C, and favored the formation of ethylene glycol and monohydric alcohols at high reaction temperature of 300 °C. Cu/TiO₂ and Cu/ZnO catalysts exhibited high catalytic activity toward the formation of hydroxyacetone with a selectivity of approx. 90 % in a wide range of reaction temperature.     

Fabrication and photocatalytic properties of novel ZnO/ZnAl2O4 nanocomposite with ZnAl2O4 dispersed inside ZnO network

Novel ZnO/ZnAl₂O₄ nanocomposites with ZnAl₂O₄ nanoparticles homogeneously dispersed inside a network of ZnO are fabricated by thermal treatment of a single‐source precursor of ZnAl‐layered double hydroxides (ZnAl‐LDHs) at 800°C. The effects of the Zn/Al molar ratio of the LDH precursors on the structure, composition, morphology, textural as well as UV‐absorbing properties and photocatalytic activities of the nanocomposites are investigated in detail. The results show that the ZnO/ZnAl₂O₄ nanocomposites derived from the ZnAl‐LDHs precursors have superior photocatalytic performances to either single phase ZnO or similar ZnO/ZnAl₂O₄ samples fabricated by chemical coprecipitation or physical mixing method. The heterojunction nanostructure and the strong coupling between the ZnO and ZnAl₂O₄ phase derived from ZnAl‐LDHs precursors are proposed to contribute the efficient spatial separation between the photo‐generated electrons and holes, which can concomitantly improve the photocatalytic activities. © 2011 American Institute of Chemical Engineers AIChE J, 2012     

Transparent zinc silicate/ zinc oxide crystallized glass-ceramics for water remediation application under visible light

The present study focuses on taking advantage of both Zinc Silicate (Zn₂SiO₄) and Zinc Oxide (ZnO) crystals in the glass matrix for enhancing photocatalytic activity. The fabricated samples were used as a photocatalyst for degrading ～ 5 mg/L concentrated “Methylene Blue” (MB) and “Rhodamine B” (RB) dye separately under visible light. For this, 44 SiO₂:11 Al₂O₃:35 ZnO:10 K₂O compositions were prepared via the traditional melt quench process followed by heat treating at a temperature of 750 °C at 2, 4, and 6 h. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) was employed to characterize the fabricated samples. The bandgap measured from Differential reflectance spectroscopy (DRS) was found to decrease with an increase in the heat treatment duration. 44 SiO₂:11 Al₂O₃:35 ZnO:10 K₂O composition heat-treated at 750 °C for 2 h degraded ～59% and ～71% of Rhodamine B (RB) dye and Methylene Blue (MB) dye under visible light in 4 h.     

α-Fe2O3 modified ZnO flower-like microstructures with enhanced photocatalytic performance for pentachlorophenol degradation

Novel α-Fe₂O₃ modified ZnO flower-like microstructures were successfully prepared via a simple and rapid solution route with different α-Fe₂O₃ contents. The products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), UV–vis diffuse reflectance spectra (UV–vis DRS) and N₂ adsorption/desorption. Photocatalytic activity of the as-prepared α-Fe₂O₃/ZnO composites was evaluated by degradation of pentachlorophenol (PCP) under simulated solar light. The results indicated that α-Fe₂O₃/ZnO composites showed higher photocatalytic activity than pure ZnO. The optimum photocatalytic activity of α-Fe₂O₃/ZnO composite with molar ratio of 1:7 was nearly 2 times as high as that of pure ZnO. The remarkably increased performance of α-Fe₂O₃/ZnO was mainly attributed to the synergistic effect between α-Fe₂O₃ and ZnO. In addition, the α-Fe₂O₃/ZnO composites also showed excellent circulation stability.     

Effect of the sonication and coating time on the photocatalytic degradation of TiO2, TiO2-Ag,and TiO2-ZnO thin film photocatalysts

Abstract

Today, the ultrasound utilizing for material synthesis has been extensively investigated. The unusual acoustic cavitation phenomenon caused by ultrasonic waves has created a new world for the production of high efficiency photocatalysts with new structures. In this study, TiO₂, TiO₂-Ag, and TiO₂-ZnO thin film photocatalysts were prepared using titanium isopropoxide Ti[OCH(CH₃)₂]₄, zinc acetate dehydrates (CH₃COO)₂Zn·2H₂O, and silver nitrate AgNO₃ by a sol–gel method under the ultrasonic irradiation. The prepared photocatalysts were characterized by UV–vis diffuse reflectance spectroscopy, X-ray diffraction, scanning electron microscopy (SEM), and energy dispersive spectroscopy. The SEM images showed that the Ag and ZnO particles were evenly dispersed in the photocatalysts due to the ultrasonic irradiation, and Ag particles were approximately 90?nm, which is relatively small compared to the photocatalysts which is not treated with ultrasonic irradiation. The catalytic activity of the photocatalysts was determined using Acid Red 27 dye. The most excellent catalytic degradation was obtained with TiO₂-ZnO thin film photocatalyst. In comparison to the conventional photocatalyst, the efficiency of photocatalytic activity of the photocatalyst produced under ultrasonication has been increased due to the reduced size of Ag and ZnO and its uniform dispersion.     

Development and characterisation of a Y2Ti2O7-based glass-ceramic as a potential oxidation protective coating for titanium suboxide (TiOx)

A silica-based glass-ceramic, with Y₂Ti₂O₇ as the major crystalline phase, is designed, characterised and tested as an oxidation-protective coating for a titanium suboxide (TiO_x) thermoelectric material at temperatures of up to 600 °C. The optimised sinter-crystallisation treatment temperatures are found to be 1300 °C and 855 °C for a duration of 30 min, and this treatment leads to a glass-ceramic with cubic Y₂Ti₂O₇ and CaAl₂Si₂O₈ as crystalline phases. An increase of ~270 °C in the dilatometric softening temperature is observed after devitrification of the parent glass, thus further extending its working temperature range.Excellent adhesion of the glass-ceramic coating to the thermoelectric material is maintained after exposure to a temperature of 600 °C for 120 h under oxidising conditions, thus confirming the effectiveness of the T1 glass-ceramic in protecting the TiO_x material.