Influence of calcination and sintering temperatures on the structure of (Pb1 − xBax )ZrO3

(Pb1–xBax)ZrO3 powders are synthesized below 800 °C for x 0.25 using a semi-wet route involving solid-state thermochemical reaction in a mixture of ZrO2 and (Pb1–xBax)CO3. The (Pb1–xBax)CO3 precursors were obtained by a forced coprecipitation technique. These powders can be sintered to achieve nearly 99% of the theoretical density at 1050 °C, which is 200 to 300 °C lower than that employed for the solid state route. The structure of as-calcined powder is orthorhombic for x 0.10 and rhombohedral for 0.25 > x 0.35, whereas the two phases coexist for 0.15 x 0.25. The structure of sintered material is orthorhombic for 0 x 0.10, rhombohedral for 0.20 x 0.30, and cubic for x 0.35, whereas orthorhombic and rhombohedral phases coexist at x = 0.15. The difference in the structure of the as-calcined and sintered powders is discussed in terms of particle size effect and chemical homogenisation of Ba2+ in the PBZ matrix.     

Microstructures of titanium-aluminides produced by laser surface alloying

The microstructures of Ti-Al layers (from 43–80 at %Al) produced by laser surface alloying of titanium substrate with a powder feed technique have been investigated. The laser processing parameters were; 1.8 kW laser power, 3 mm beam diameter, 7 mm s^–1 traverse speed, and values of powder flow rates of aluminium ranging from 0.07–0.11 g s^–1. The microstructures were dendrites of ₂ and interdendritic regions of ₂+ in the Ti-43 at %Al alloy; dendrites of either ₂ or ₂+ with interdendritic in the Ti-50 at %Al alloy; dendrites of ₂+ with interdendritic in the Ti-55 at %Al alloy; single phase in the Ti-60 at %Al alloy and TiAl₃ dendrites and Al solid solution in the interdendritic regions in the Ti-80 at %Al alloy. The microstructures were fine and comparable to those produced by other methods of rapid solidification processing. The microstructures of the Ti-50 and Ti-55 at %Al alloys were in agreement with the existence of the peritectic reactions:L + andL + , in the Ti-Al system.     

Nonsteady heat transfer in semi-infinite region with nonlinear heat-absorption law

The method of determining the temperature gradient at the boundary of a semi-infinite region proposed earlier for linear problems [1–3] is outlined as it applies to a nonlinear problem.Notation D fractional-differentiation symbol - T temperature - q temperature gradient - k parameter characterizing heat-transfer rate-, x, t, coordinate and time - , , coefficients of general heat-conduction equation - constant Indices s surface Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 143–147, July, 1980.     

Flux motion in anisotropic type-II superconductors nearH c 2 with arbitrary vortex orientation

Flux motion in anisotropic type-II superconductors near H_{c 2} is studied in the framework of the time-dependent Ginzburg-Landau (TDGL) theory for the case that the average flux densityB is oriented in an arbitrary direction relative to the principal axes of the sample. The linearized TDGL equation for a uniformly translating order parameter is solved and expressions for all elements of the flux-flow resistivity tensor _ij (including the off-diagonal Hall elements) are obtained. The diagonal elements _ii show the angular scaling property that _ii(B) = _ii(B/H_{c 2}(, ø)), whereas the Hall elements _ij (i j) have additional angular dependences that are not contained in H_c2. For the case that the normal state Hall elements _ij ⁽ⁿ⁾ B _k with i j k, the ratios _ij/ _ij ⁽ⁿ⁾ are functions of B/H_c2 (, ) only.     

Experimental study of the boundary between single-phase convection and boiling in underheated cryogenic liquids

The effect of pressure and underheating on the position of the boundary between heat-transfer regimes in liquid helium and hydrogen is investigated.Notation q heat flux - p pressure - =T_s–T underheating - T_s saturation temperature - T temperature of liquid - T=T_wa – T T_s=T_wa – T_s - T_wa temperature of heat-emitting surface - A,a, B, b, C constants - m, n indices - Nu Nusselt number - Ra Rayleigh number - thermal conductivity - coefficient of cubical expansion - kinematic viscosity - g acceleration - standard deviation Indices 01 conditions of convection-boiling transition - 02 conditions of boiling-convection transition Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 42, No. 1, pp. 5–11, January, 1982.     

Effect of zinc on the magnetic properties of acicular cobalt-modified γ-Fe2O3 particles

Acicular -FeOOH particles with a particle length of about 0.35 m and an axial ratio of about 7 were synthesized by the coprecipitation method using the reaction of FeCl₂-NaOH. The (Co, Zn)-modified -F₂O₃ particles were produced by absorbing Co²⁺ and Zn²⁺ ions on the surfaces of -FeOOH particles followed by dehydration, reduction and oxidation. The saturation magnetization and thermal stability of the coercivity of (Co, Zn)--Fe₂O₃ particles were all higher than those of Co--F₂O₃ particles. For the same (Co+Zn) content, the saturation magnetization of (Co, Zn)--Fe₂O₃ particles increased with increasing zinc content but the coercivity decreased.     

Structure and Diamagnetic Properties of (Pb0.6SnyCu0.4 ? y)Sr2(Y1 ? xCax)Cu2Oz

The effect of Sn doping in (Pb_0.6Sn _y Cu_{0.4 – y} )Sr₂(Y_{1 – x} Ca _x )Cu₂O _z with 0 y 0.3 and 0 x 0.7 was investigated. It was established that a nearly pure 1212 phase can be obtained at 0 y 0.1 and 0 x 0.3. The obtained XRD patterns as well as the results of the EDX and ICP-AES analyses showed that Sn substitution is possible in the (Pb,Cu)-1212 phase. Superconductivity was observed at 0.4 x 0.7. The onset of the diamagnetic transitions varied from 10 to 30 K. The influence of the strong Pb deficiency on the superconducting properties of the samples was discussed.     

Equations of generalized thermoelasticity of a Cosserat medium in stresses

Thermoelasticity equations in stresses are derived in this paper for a Cosserat medium taking into account the finiteness of the heat propagation velocity. A theorem is proved on the uniqueness of the solution for one of the obtained systems of such equations.Notation u displacement vector - small rotation vector - absolute temperature - ₀ initial temperature of the medium - relative deviation of the temperature from the initial value - , , , , , ,, m constants characterizing the mechanical or thermophysical properties of the medium - density - I dynamic characteristic of the medium reaction during rotation - k heat conduction coefficient - ₀ a constant characterizing the velocity of heat propagation - X external volume force vector - Y external volume moment vector - w density of the heat liberation sources distributed in the medium - E unit tensor - T force stress tensor - M moment stress tensor - nonsymmetric strain tensor - bending-torsion tensor - s entropy referred to unit volume - V volume occupied by the body - surface bounding the body - (T)_ki, (M)_ki components of the tensorsT andM - q thermal flux vector Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 40, No. 3, pp. 482–488, March, 1981.     

Standard Gibbs' energies of formation of BaCuO2, Y2Cu2O5 and Y2BaCuO5

The Gibbs' energies of formation of BaCuO₂, Y₂Cu₂O₅ and Y₂BaCuO₅ from component oxides have been measured using solid state galvanic cells incorporating CaF₂ as the solid electrolyte under pure oxygen at a pressure of 1.01×10⁵ Pa BaO + CuO BaCuO₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=–63.4–0.0525T(K) Y₂O₃ + 2CuO Y₂Cu₂O₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=18.47–0.0219T(K) Y₂O₃ + BaO + CuO Y₂BaCuO₅ G _f,ox ^o (± 0.7) (kJ mol^–1)=–72.5–0.0793T(K) Because the superconducting compound YBa₂Cu₃O_7– coexists with any two of the phases CuO, BaCuO₂ and Y₂BaCuO₅, the data on BaCuO₂ and Y₂BaCuO₅ obtained in this study provide the basis for the evaluation of the Gibbs' energy of formation of the 1-2-3 compound at high temperatures.     

Investigation of the state of metal surfaces under boundary-lubrication conditions in the presence of additives

The concepts of secondary structures and boundary friction were substantial in the framework of the theory of the nature of the phenomena taking place during friction. The results of an investigation into changes in the state of metal surfaces under the influence of iron and copper rhodanide additions in lubricating oils are described as an example. Schematic models were proposed for the structure of metal surface layers produced under normal frictional conditions and as a result of seizing of the I-st and II-nd kind.Translated from Fiziko-Khimicheskaya Mekhanika Materialov, Vol. 5, No. 5, pp. 559–564, Septmeber–October, 1969.     

The influence of ageing on the stability of β-γ/γ′ derived microstructures in Ni-Al-Cr-(Co) alloys

Multiphase Ni-Al-(Fe)-(Cr)-(Co)-based intermetallics with (B2)- (A1)/(L1₂), - or - microstructures can exhibit significant room-temperature tensile ductility. In the case of Ni-Al-Cr-based alloys, microstructural development is complicated by the precipitation of -Cr, which can supplant the -phase during ageing of three-phase -/ microstructures. An investigation of the stability, during ageing, of cast Ni-Al-Cr-(Co) alloys with microstructures derived from -/ is reported. In the as-cast condition, the materials investigated consisted of a dendritic matrix containing L1₀ type martensite and interdendritic /. Extensive intra- and interdendritic -Cr precipitation was also observed. The stability during ageing of the interdendritic / microstructure is also considered and transformation of the L1₀ martensite is examined.     

Numerical Analysis of the Effect of Viscosity on the Vortex Dynamics in Laminar Separated Flow Past a Dimple on a Plane with Allowance for Its Asymmetry

Based on numerical solution of the Navier–Stokes threedimensional stationary equations by a factorized finitevolume method, the influence of physical viscosity on selforganizing jetvortex structures in a dimple on a plane immersed in a laminar flow is analyzed with allowance for the asymmetry of the dimple shape.     

Radiation of internal waves during vertical motion of a body through a nonuniform liquid

Energy losses to radiation of internal waves during the vertical motion of a point dipole in two-dimensional and three-dimensional cases are computed.Notation _o(z), p_o(z) density and pressure of the ground state - z vertical coordinate - v, p, perturbed velocity, pressure, and density - H(d 1n _o/dz)^–1 characteristic length scale for stratification - N=(gH^–1–g²c _o ^–2 )^1/2 Weisel-Brent frequency - g acceleration of gravity - c_o speed of sound - vertical component of the perturbed velocity - V vector operator - k wave vector - frequency - d vector surface element - W magnitude of the energy losses - (t), (r) (x)(y)(z) Dirac functions - v_o velocity of motion of the source of perturbations - d dipole moment of the doublet - _o,l length dimension parameters - _o intensity of the source Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 4, pp. 619–623, October, 1980.     

Microstructural development in cast alloys based on the β-NiAl–β′-Ni2AlTi–γ′-Ni3Al–α-Cr system

An investigation of microstructural development in three arc-cast Ni–Al–Cr–Ti multiphase alloys derived from the B2 type -NiAl phase is presented. Detailed microstructural characterization of Ni–25 at % Al–20 at % Cr–15 at % Ti, Ni–26 at % Al–21 at % Cr–11 at % Ti and Ni–25 at % Al–24 at % Cr–15 at % Ti materials by transmission electron microscopy (TEM), is described. Microstructural development is examined in both the as-cast condition and after 140 h homogenization treatments at both 850 and 1100 °C. The formation of a eutectic between an L21-type phase (Heusler phase, with a nominal composition of Ni2AlTi) and elemental -Cr is examined. The precipitation of within () and vice versa, in both the inter- and intradendritic regions, is considered. The formation of L12-type (nominally Ni3Al) precipitates within the and -phases is discussed, as is the transformation of to two-phase / during ageing. © 1998 Chapman & Hall     

Nonlinear Response of a Continuous Wave NMR Spectrometer for Samples with a Large Magnetization

We present a new insight in the response of a CW NMR spectrometer for highly magnetized samples above 100 MHz. The spectrometer is a bridge made of a magic T. The output of the bridge is proportional to the reflection coefficient, , of a resonant circuit, which is built with a coil containing the sample. The sensitivity of the reflection coefficient to the complex susceptibility of the sample, () = () – j(), depends on the quality factor, Q, of the circuit and filling factor, . When the condition Q 1 is not fulfilled, we show indeed that the use of a simple crystal detector, which is only sensitive to || gives rise to a strong nonlinear response of the spectrometer. Measurements of the complex value of by means of phase sensitive detection allow to recover a linear behavior. We discuss and illustrate those issues with a few circuits we designed for our measurements on liquid ³ He with spin polarizations up to 15 %. A method is described to build in a reproducible and predictable way resonant circuits matched to 50 in the frequency range 100 – 400 MHz with a quality factor as high as 1000 at 4 K.     

High-frequency dielectric properties of Mg-Al-Si,Ca-Al-Si and Y-Al-Si oxynitride glasses

Recently developed coaxial line techniques [1] have been used to determine, at room temperature, the values of the real () and imaginary (') parts of the dielectric constants for some Mg-Al-Si, Ca-Al-Si and Y-Al-Si oxynitride glasses over the frequency range 500 MHz to 5 GHz. The frequency dependencies of and ' are consistent with the universal law of dielectric response in that (-_t8)^(n–1) and '^(n–1) for all glass compositions; the high experimental value of the exponent (n=1.0±0.1) suggests the limiting form of lattice loss [2] situation. In this frequency range, as previously reported [3] at longer wavelengths, the addition of nitrogen increases the dielectric constant, (); in both the oxide and oxynitride glasses is also influenced by the cation, being increased with cation type in the order magnesium, yttrium, calcium as at lower frequencies.     

Fermi-Hypernetted Chain Theory for Liquid 3He: A Reassessment

The Fermi–Hypernetted Chain theory for ³He is reviewed. We develop the theory step by step by the inclusion of elementary diagrams, triplet-correlations, propagator corrections, and spin-correlations. Simulation data are reproduced at each level of implementation. So-called backflow correlations are identified to be a consequence of the mean spherical approximation which is implicit to the Jastrow–Feenberg wave function for fermions. Results of the best calculation for the energetics and structure functions agree within 0.2–0.3 K with experiments.     

Particle size control of 1,3,5-triamino-2,4,6-trinitrobenzene by recrystallization from DMSO

Batches of up to 46g of the insensitive explosive 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) have been recrystallized from DMSO in an effort to prepare larger particle-size material for recycling previously-used TATB and also for use in special formulations. The first part of the study investigated the conditions required to shift the particle-size distribution maximum from 50–70 m to several hundred micrometres in diameter. Distributions peaking at 200–246 m were successfully produced by varying the cooldown rate and degree of agitation during cooling. The second part of the study emphasized regeneration of the standard 50–70 m distribution from submicron size (ultrafine TATB) particles. The distributions peaking at 76–88 m, 27–31 m, and 15–17 m, successfully bracketed the target particle sizes, were grown by changing the degree of solution saturation. The choice of saturation temperature for the TATB/DMSO solution was based on earlier small-scale recrystallization and solubility work.     

Equation of state of3He near its liquid-vapor critical point

We report high-resolution measurements of the pressure coefficient (P/T) for³He in both the one-phase and two-phase regions close to the critical point. These include data on 40 isochores over the intervals–0.1t+0.1 and–0.2+0.2, wheret=(T–T _c )/T _c and =(– _c )/ _c . We have determined the discontinuity (P/T) of (P/T) between the one-phase and the two-phase regions along the coexistence curve as a function of . The asymptotic behavior of (1/) (P/T) versus near the critical point gives a power law with an exponent (+–1)^–1=1.39±0.02 for0.010.2 or–1×10 ^–2t–10 ^–6 , from which we deduce =1.14±0.01, using =0.361 determined from the shape of the coexistence curve. An analysis of the discontinuity (P/T) with a correction-to-scaling term gives =1.17±0.02. The quoted errors are fromstatistics alone. Furthermore, we combine our data with heat capacity results by Brown and Meyer to calculate (/T) _c as a function oft. In the two-phase region the slope (²/T ²)_c is different from that in the one-phase region. These findings are discussed in the light of the predictions from simple scaling and more refined theories and model calculations. For the isochores 0 we form a scaling plot to test whether the data follow simple scaling, which assumes antisymmetry of – ( _c ,t) as a function of on both sides of the critical isochore. We find that indeed this plot shows that the assumption of simple scaling holds reasonably well for our data over the ranget0.1. A fit of our data to the linear model approximation is obtained for0.10 andt0.02, giving a value of =1.16±0.02. Beyond this range, deviations between the fit and the data are greater than the experimental scatter. Finally we discuss the (P/T) data analysis for ⁴ He by Kierstead. A power law plot of (1/) P/T) versus belowT _c leads to =1.13±0.10. An analysis with a correction-to-scaling term gives =1.06±0.02. In contrast to ³ He, the slopes (²/T ²)_c above and belowT _c are only marginally different.Work supported by a grant from the National Science Foundation.     

Chebyshev approximation for the roots of the equation BiWГ(μ)=μVГ(μ)

A minimax approximation, uniform for Bi [0, ), is developed for the roots of the equation BiW()=V(), by means of Chebyshev polynomials.Translated from Inzhenero-Fizicheskii Zhurnal, Vol. 28, No. 4, pp. 710–715, April, 1975.