Mechanochemical synthesis of nanocrystalline ZnWO4 at room temperature

Single nanocrystalline ZnWO₄ powders were successfully synthesized by ball milling at room temperature. A stoichiometric mixture of ZnO and WO₃ in a 1:1 molar ratio was subjected to intense mechanical treatment in air using a planetary ball mill (Fritsch - Premium line - Pulversette No. 7) for a period varying from 5 to 300 min. The influence of the four different milling conditions was investigated on the formation of ZnWO₄. The products obtained were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmer-Teller (BET) surface area, infrared (IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The synthesis of ZnWO₄ powder started after 5 min milling time and finished after 30 min milling time at a higher speed (1000 rpm). The mechanical treatment up to 300 min did not lead to phase and structure change of ZnWO₄. The product obtained contained nanoparticles with a size of about 50 nm. The photocatalytic activity of the ZnWO₄ powders obtained was investigated by degradation of a model aqueous solution of Malachite Green (MG) upon UV-light irradiation.     

Synthesis and electrochemical properties of porous LiV3O8 as cathode materials for lithium-ion batteries

In this paper, we report on the synthesis of porous LiV₃O₈ by using a tartaric acid-assisted sol-gel process and their enhanced electrochemical properties for reversible lithium storage. The crystal structure, morphology and pore texture of the as-synthesized samples are characterized by means of XRD, SEM, TEM/HRTEM and N₂ adsorption/desorption measurements. The results show that the tartaric acid plays a pore-making function and the calcination temperature is an important influential factor to the pore texture. In particular, the porous LiV₃O₈ calcined at 300 °C (LiV₃O₈-300) exhibits hierarchical porous structure with high surface area of 152.4 m² g⁻¹. The electrochemical performance of the as-prepared porous LiV₃O₈ as cathode materials for lithium ion batteries is investigated by galvanostatic charge-discharge cycling and electrochemical impedance spectroscopy. The porous LiV₃O₈-300 displays a maximum discharge capacity of 320 mAh g⁻¹ and remains 96.3% of its initial discharge capacity after 50 charge/discharge cycles at the current density of 40 mA g⁻¹ due to the enhanced charge transfer kinetics with a low apparent activity energy of 35.2 kJ mol⁻¹, suggesting its promising application as the cathode material of Li-ion batteries.     

Characteristics of BaO-B2O3-SiO2 nano glass powders prepared by flame spray pyrolysis as the sintering agent of BaTiO3 ceramics

Nanosized BaO-B₂O₃-SiO₂ glass powders are directly prepared by flame spray pyrolysis. The mean size of the BaO-B₂O₃-SiO₂ glass powders with amorphous phase and spherical shape is 30 nm. The effects of glass powders on the sintering characteristics of the BaTiO₃ pellet formed from the nanosized BaTiO₃ powders are investigated. The mean size and BET surface area of the BaTiO₃ powders prepared by spray pyrolysis are 110 nm and 9.1 m²/g. The BaTiO₃ pellet with glass additive has large grain size with several microns, dense structure and pure tetragonal crystal structure at a sintering temperature of 1000 °C. The XRD pattern of the pellet has distinct split of (2 0 0) and (0 0 2) peaks at 2θ ≈ 44.95°. The dielectric constant of the pellet without glass additive is 2180. However, the dielectric constants of the pellets with 1, 3, 5 and 7 wt% glass additive with respect to BaTiO₃ are 2496, 2514, 2700 and 2225, respectively.     

Microstructural evolution of nanostructured Ti0.9Al0.1N prepared by reactive ball-milling

Nanocrystalline stoichiometric Ti_0.9Al_0.1N powder has been prepared by ball-milling the α-Ti (hcp) and aluminum (fcc) powders under N₂ at room temperature. Initially, α-Ti phase partially transformed to the transient cubic β-Ti phase and Ti_0.9Al_0.1N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti_0.9Al_0.1N phase is formed after 7 h of milling. After 1 h of milling, all Al atoms are diffused into the α-Ti matrix. The transient β-Ti phase is noticed to form after 1 h of milling and disappears completely after 7 h of milling. Microstructure characterization of unmilled and ball-milled powders by analyzing XRD patterns employing the Rietveld structure refinement reveals the inclusion of Al and nitrogen atoms into the Ti lattice on the way to formation of Ti_0.9Al_0.1N phase. Microstructure of ball-milled samples is also characterized by HRTEM. The particle size of Ti_0.9Al_0.1N phase, as obtained from XRD method, is ∼5 nm which is very close to that obtained from HRTEM.     

Porous Li4Ti5O12 anode material synthesized by one-step solid state method for electrochemical properties enhancement

A porous Li₄Ti₅O₁₂ anode material was successfully synthesized from mixture of LiCl and TiCl₄ with 70 wt% oxalic acid by a modified one-step solid state method. The anode material Li₄Ti₅O₁₂ exhibited a cubic spinel structure and only one voltage plateau occurred around 1.5 V. The initial capacity of porous Li₄Ti₅O₁₂ was 167 and 133 mAh g⁻¹ at 0.5 and 1C charge/discharge rate, respectively, and the capacity retention maintained above 98% after 200 cycles. The porous Li₄Ti₅O₁₂ structure showed promising rate performance with a capacity of 70 mAh g⁻¹ at charge/discharge 10C rate after 200 cycles. It was demonstrated that the porous structure could withstand 50C charge/discharge rate and exhibited excellent cycling stability.     

Ionic compounds lamination reaction and characteristics of photosensitive copper indium sulfide on titania nanotube arrays

This study investigates using an inorganic photosensitive CuInS₂ (CIS) coating instead of an organic dye on TiO₂ nanotube arrays (TNAs). The stoichiometric characteristics by use of various deposition parameters such as precursor concentrations (0.1 M, 0.05 M, and 0.01 M) and deposition cycles (1-60 cycles) are then analyzed in relation to the crystallinity and photosensitivity. TNAs are synthesized by anodic oxidation of Ti metal, modified by the TiO₂ film, and are subsequently annealed at 450 °C for 30 min, producing what are named T-TNAs. They show high photocatalytic efficiency and photosensitivity under UV-illumination. The photosensitive CIS coatings on the T-TNAs are processed by an ionic compounds lamination reaction (ICLR) method. The more immersion cycles and the higher the precursor concentration of copper sulfide, the more CIS peeled off as precipitates formed, which result in less indium sulfide deposition being required for reacting with the copper sulfide to reach stoichiometry. Near stoichiometric CIS can be obtained by controlling the precursor concentration and deposition cycles of the ICLR process. Good crystallinity and n-type characteristics are achieved by controlling the precursor concentrations and deposition cycles suitably to obtain a high current density. When the Cu/In ratio is adjusted for n-type characteristics, the current density reaches at least 300 μA/cm² under visible light illumination intensity of 100 mW/cm².     

Synthesis of Ti3SiC2 bulks by infiltration method

T₃SiC₂ bulks have been synthesized by infiltrating Si liquid into porous precursor pellets composed of solid TiC and Ti powders. Silicon pellets were placed at the bottom of the precursor pellets as the liquid source. The starting compositions can be represented by the formula 2TiC + Ti + xSi, where x = 1.0, 1.2, 1.5 and 1.8, respectively. The phase formation and microstructure of the bulks were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy-dispersive spectroscopy (EDS) system. The results demonstrated that the TiC/Ti precursor pellet could only react with Si completely when the x value is 1.8. Impurities SiC, Ti-Si binary compounds and Ti₈C₅ appeared along the silicon diffusion direction. It is found that the compositions of impurities strongly depended on the Si-concentration. Reaction mechanism of this Ti₃SiC₂ infiltration synthesis has also been discussed based on the Si-concentration changes on the diffusion path.     

Single step synthesis of GdAlO3 powder

A novel method for preparation of nano-crystalline gadolinium aluminate (GdAlO₃) powder, based on combustion synthesis, is reported. It was observed that aluminium nitrate and gadolinium nitrate exhibit different combustion characteristics with respect to urea, glycine and β-alanine. While urea was proven to be a suitable fuel for direct formation of crystalline α-Al₂O₃ from its nitrate, glycine and β-alanine are suitable fuels for gadolinium nitrate for preparation of its oxide after combustion reaction. Based on the observed chemical characteristics of gadolinium and aluminium nitrates with respect to above mentioned fuels for the combustion reaction, the fuel mixture composition could be predicted that could lead to phase pure perovskite GdAlO₃ directly after the combustion reaction without any subsequent calcination step. The use of single fuel, on the other hand, leads to formation of amorphous precursor powders that call for subsequent calcination for the formation of crystalline GdAlO₃. The powders produced directly after combustion reactions using fuel mixtures were found to be highly sinterable. The sintering of the powders at 1550 °C for 4 h resulted in GdAlO₃ with sintered density of more than 95%. T.D.     

Synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanosized powders prepared using a simple co-precipitation process

The synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanopowders prepared using a simple co-precipitation process at 348 K and pH = 7 were investigated using differential scanning calorimetry/thermogravimetry (DSC/TG), an X-ray diffractometer (XRD), the Raman spectra, transmission electron microscopy (TEM), selected area electron diffraction (SAED), and an energy dispersive spectrometer (EDS). The activation energy of tetragonal ZrO₂ crystallization from 3Y-TZP freeze-dried precursor powders using a non-isothermal method, namely, 169.2 ± 21.9 kJ mol⁻¹, was obtained. The growth morphology parameter n was approximated as 2.0, which indicated that it had a plate-like morphology. The XRD, Raman spectra, and SAED patterns showed that the phase of the tetragonal ZrO₂ was maintained at 1273 K. The crystallite size of 3Y-TZP freeze-dried precursor powders calcined at 1273 K for 5 min was 21.3 nm.     

Preparation and characterization of CoFe2O4 powders and films via the sol-gel method

The CoFe₂O₄ (CFO) starting precursor solutions were prepared by two sol-gel methods. The XRD results show that the second sol-gel method is a better method to obtain CFO materials with high purity. The CFO precursor solutions prepared by the second sol-gel method were spin-coated onto the Pt/Ti/SiO₂/Si substrate to obtain CFO films. With the increase of annealing temperature, the relative amounts of secondary phases in CFO films are decreased. When annealed at 700 °C, CFO films are almost composed of the main phase and the substrate phase without secondary phases. The CFO film is crack-free and has compact structure without any pore. The thickness of CFO film is about 49 nm. The starting precursor solution with the concentration of 0.15 mol L⁻¹ is better for preparing CFO films. The CFO films with nano-scaled film thicknesses have better magnetic properties than the CFO powders.     

Photoluminescent studies on porous silicon/tin oxide heterostructures

Porous silicon (PSi) structure was formed at different current densities in the range of 5-60 mA/cm² by the electrochemical anodization of PSi wafers etching in HF for 30 min. The PSi was characterized by X-ray diffraction studies. The PSi samples prepared at current densities above and below 30 mA/cm² show PL spectra with asymmetric and overlapped peaks. On the top surface as well as inside the pores of this PSi structures the precursor sol-gel was incorporated by the spin coating technique and SnO₂ was formed by heating at 400 °C in air. Peaks pertaining to PSi along with those corresponding to SnO₂ were observed, which confirmed SnO₂ formation as thin film on the PSi surface. The PL spectra of SnO₂/PSi structure aged for two months indicated a reduction in PL intensity but remained constant afterwards. SnO₂ not only modifies the nature of silicon nanopores but also is expected to influence the interface states in SnO₂/PSi junction.     

Low temperature growth of nanocrystalline TiO2 films with Ar/O2 low-field helicon plasma

TiO₂ thin films were deposited on silicon wafer substrates by low-field (1 < B < 5 mT) helicon plasma assisted reactive sputtering in a mixture of pure argon and oxygen. The influence of the positive ion density on the substrate and the post-annealing treatment on the films density, refractive index, chemical composition and crystalline structure was analysed by reflectometry, Rutherford backscattering spectroscopy (RBS) and X-ray diffraction (XRD). Amorphous TiO₂ was obtained for ion density on the substrate below 7 × 10¹⁶ m^− 3. Increasing the ion density over 7 × 10¹⁶ m^− 3 led to the formation of nanocrystalline (~ 15 nm) rutile phase TiO₂. The post-annealing treatment of the films in air at 300 °C induced the complete crystallisation of the amorphous films to nanocrystals of anatase (~ 40 nm) while the rutile films shows no significant change meaning that they were already fully crystallised by the plasma process. All these results show an efficient process by low-field helicon plasma sputtering process to fabricate stoichiometric TiO₂ thin films with amorphous or nanocrystalline rutile structure directly from low temperature plasma processing conditions and nanocrystalline anatase structure with a moderate annealing treatment.     

Structural, optical and charge transport study of rutile TiO2 nanocrystals at two calcination temperatures

In this study the influence of two different calcination temperatures 80 °C and 450 °C on the structural, optical and charge transport properties of rutile TiO₂ nanocrystals has been investigated. TiO₂ nanocrystals have been prepared at low temperature by a simple hydrolysis method using titanium tetrachloride as starting precursor. The results of X-ray diffraction (XRD) showed that the prepared nanocrystals have a rutile tetragonal crystalline structure. Specific surface area of 80 °C and 450 °C calcinated rutile TiO₂ nanocrystals are 25.38 × 10⁵ cm²/g and 7.61 × 10⁵ cm²/g respectively, which has been calculated by X-ray diffraction data. Williamson-Hall plot results indicate the presence of compressive strain at 80 °C and tensile strain at 450 °C. Ultraviolet-visible (UV-vis) absorption spectroscopy is used to calculate the band gap of the material and the shift in absorption edge and it has been observed that the absorption spectra are strongly modified by the calcination temperature. The red-shift in photoluminescence (PL) is attributed to the change in strain from compressive to tensile. Photoconductivity (PC) measurements showed that capture cross-section of 80 °C (R1) and 450 °C (R2) calcinated rutile nanocrystals are 55.10 × 10⁻¹⁰ and 39.50 × 10⁻¹⁰ cm² respectively. High value of electron life-time, low value of radiative recombination and a four order increase in photogenerated charge carriers have been reported for the rutile TiO₂ nanocrystals calcinated at 450 °C.     

Preparation of large scale photocatalytic TiO2 films by the sol-gel process

Nanocrystalline titanium dioxide films were formed on frosted and clear borosilicate glass with a large surface area (12 × 22 cm) using doctor blade and spray coating techniques. The films were subjected to a high temperature treatment at 550 °C. X-ray diffraction (XRD) analysis indicated that the TiO₂ films contain only the anatase phase. Optical microscopy was used to determine the morphology changes after the deposition of each layer. Scanning electron microscopy (SEM) was used to study the films surface morphology. The large scale TiO₂ films produced showed a high photocatalytic activity which was evaluated by the degradation of methyl orange (MO) in aqueous solution (10 mg L^− 1) under illumination of a UV light source with an overall irradiance of 0.9 mW cm^− 2. UV-visible spectrophotometry was used to monitor the degradation of MO through the decrease of the main absorbance peak at 464 nm. The results demonstrated that a complete decomposition of MO could be achieved after 2 h of UV irradiation.     

Synthesis of carbon coated nanocrystalline porous α-LiFeO2 composite and its application as anode for the lithium ion battery

In this work, we describe for the first time a high surface area nanocrystalline porous α-LiFeO₂-C composite anode material synthesized by a simple molten salt method, followed by a carbon coating process. The synthesized nanocomposite presents an interconnected porous architecture, as was confirmed by field emission scanning electron microscope observations. Transmission electron microscope investigations revealed that amorphous carbon was incorporated into the pores among the nanoparticles and that some nanoparticles were covered by a thin layer of amorphous carbon as well. Electrochemical measurements showed that the carbon played an important role, as it affected both the cycle life and the rate capability of the electrode. The α-LiFeO₂-C nanocomposite electrode delivered a higher reversible capacity and good cycle stability (540 mAh g⁻¹ at 1 C after 200 cycles) compared to the pure α-LiFeO₂ electrode. Good electrochemical performance of the α-LiFeO₂-C nanocomposite electrode could be attributed to the porous conductive architecture among the nanoparticles, which not only has benefits in terms of decreasing the absolute volume changes and increasing the mobility of lithium ions, but also offers conductive pathways along the whole interconnected wall in the structure, which is favourable for the transport of electrons, promotes liquid electrolyte diffusion into the bulk material, and acts as a buffer zone to absorb the volume changes. Our results indicate that α-LiFeO₂-C nanocomposite could be considered as a potential anode material for lithium-ion batteries.     

Effect of carbon source on the carbothermal reduction nitridation for synthesis of (Ti, W, Mo, V)(C, N) nanocrystalline powders

The effect of carbon source on the carbothermal reduction-nitridation during synthesizing (Ti, W, Mo, V)(C, N) nanocrystalline powders was investigated. For a systematic comparison, activated carbon, graphite and two kinds of carbon black powder were used as reducing agents in this study. Ultrafine (Ti, W, Mo, V)(C, N) powders with a particle size of ~ 200-500 nm have been produced at 1450 °C for 2 h by using nanosized carbon black source with small particle size. The presence of phases in the reaction products was characterized with X-ray diffraction (XRD) and the microstructure of carbon source powders and final products was studied by scanning electron microscopy (SEM). The results show that the formation of the Ti(C, N) phase is strongly dependent on the particle size of carbon source powders, and the synthesizing temperature of the Ti(C, N) phase decreases significantly from 1750 °C to 1300 °C by using nanosized carbon black, as compared with micron graphite. In addition, activated carbon with a particle size of 5-50 μm does not favor the dissolution of tungsten or molybdenum carbides into Ti(C, N) despite its large specific surface area.     

Perpendicular magnetic anisotropy in 70 nm CoFe2O4 thin films fabricated on SiO2/Si(1 0 0) by the sol-gel method

Cobalt ferrite CoFe₂O₄ films were fabricated on SiO₂/Si(1 0 0) by the sol-gel method. Films crystallized at/above 600 °C are stoichiometric as expected. With increase of the annealing temperature from 600 °C to 750 °C, the columnar grain size of CoFe₂O₄ film increases from 13 nm to 50 nm, resulting in surface roughness increasing from 0.46 nm to 2.55 nm. Magnetic hysteresis loops in both in-plane and out-of-plane directions, at different annealing temperatures, indicate that the films annealed at 750 °C exhibit obvious perpendicular magnetic anisotropy. Simultaneously, with the annealing temperature increasing from 600 °C to 750 °C, the out of plane coercivity increases from 1 kOe to 2.4 kOe and the corresponding saturation magnetization increases from 200 emu/cm³ to 283 emu/cm³. In addition, all crystallized films exhibit cluster-like structured magnetic domains.     

Ba(Ti1 − xSnx)O3 (x = 0.13) nanomaterials produced by low-temperature aqueous synthesis

BaTi_0.87Sn_0.13O₃ (BTS₁₃) nanopowder was prepared by low-temperature aqueous synthesis (LTAS) method. The evolution of the structure and microstructure of the precursor precipitate, heated at temperatures up to 1000 °C was studied by TGA, FT-IR, SEM and XRD techniques. The dried precipitate showed a microstructure consisting of nano-sized grains (∼40 nm) with great tendency to agglomeration. BaTi_0.87Sn_0.13O₃ single phase was obtained at 800 °C. The ceramics prepared from as-obtained BTS₁₃ powders (60-70 nm) show good dielectric and ferroelectric characteristics. The dielectric constant was about 4800 and the dielectric loss (tan δ) was 0.229 at 1 kHz and at the Curie temperature (31 °C). The remanent polarization (P_r) and the coercive field (E_C) of Ba_0.97Ho_0.03TiO₃ ceramics, at 1 kHz, were P_r = 13 μC/cm² and E_C = 0.89 kV/cm. The ferroelectric parameters E_C and P_r decrease with increasing frequency in the domain 100 Hz to 10 kHz.     

Effect of fuel-to-nitrate ratio on the powder characteristics of nanosized CeO2 synthesized by mixed fuel combustion method

Synthesis of nanocrystalline ceria powders is carried out through the mixed fuel combustion approach by using different combinations of glycine and citric acid. The powders obtained with different fuel-to-nitrate (F/N) ratios are characterized by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), BET surface area analysis, and Raman spectroscopy. TGA and FTIR spectroscopy studies have revealed the presence of carbonaceous species and residual volatiles in the combustion synthesized ceria powders. It is observed that the variation of fuel-to-nitrate ratio has a profound influence on the carbonaceous residues from combustion, crystallite size (11-44 nm), surface area (9-39 m²/g) and morphology of the resultant powders. The Raman spectroscopy results on the variation of particle size with F/N ratio are consistent with the conclusions made from X-ray line broadening and BET surface area analysis.     

Synthesis of WC nanopowders from novel precursors

Nano-WC powders with granular particle of ~ 20-80 nm were synthesized by a new precursor method, namely carbothermal reduction-carburization of amorphous WO₃-C mixture, which was made initially from salt solution containing tungsten and carbon elements by air drying and subsequent calcining at 400 °C for 1 h. The reaction products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques. The results show that the synthesizing temperature of WC powders was reduced greatly by the novel precursor method. Thus, the preparation of the single-phase nano-WC powders is at only 1000 °C for 2 h. The lowering of synthesizing temperature is mainly due to the homogeneous chemical composition of the amorphous oxide-carbon mixture.