High-dielectric-constant and low-loss microwave dielectric in the (1 − x)La(Mg0.5Ti0.5)O3-x(Ca0.8Sr0.2)TiO3 solid solution system

The microwave dielectric properties and microstructures of (1 − x)La(Mg_0.5Ti_0.5)O₃-x(Ca_0.8Sr_0.2)TiO₃ ceramics, prepared by a mixed oxide route, have been investigated. The forming of solid solutions was confirmed by the XRD patterns and the measured lattice parameters for all compositions. A near zero τ_f was achieved for samples with x = 0.5, although the dielectric properties varied with sintering temperature. The Q × f value of 0.5La(Mg_0.5Ti_0.5)O₃-0.5(Ca_0.8Sr_0.2)TiO₃ increased up to 1475 °C, after which it decreased. The decrease in dielectric properties was coincident with the onset of rapid grain growth. The optimum combination of microwave dielectric properties was achieved at 1475 °C for samples where x = 0.5 with a dielectric constant ?_r of 47.12, a Q × f value of 35,000 GHz (measured at 6.2 GHz) and a τ_f value of −4.7 ppm/°C.     

X-ray diffraction and dielectric studies across morphotropic phase boundary in (1 − x) [Pb(Mg0.5W0.5)O3]-xPbTiO3 ceramics

We present here the results of comprehensive X-ray diffraction and dielectric studies on several compositions of (1 − x)[Pb(Mg_0.5W_0.5)O₃]-xPbTiO₃ (PMW-xPT) solid solution across the morphotropic phase boundary. Rietveld analysis of the powder X-ray diffraction data reveals cubic (space group Fm3m) structure of PMW-xPT ceramics for the compositions with x ≤ 0.42, tetragonal (space group P4mm) structure for the compositions with x ≥ 0.72 and coexistence of the tetragonal and cubic phases for the intermediate compositions (0.46 ≤ x ≤ 0.68). Temperature dependence of the dielectric permittivity above room temperature exhibits diffuse nature of phase transitions for the compositions in the cubic and two phase region while the compositions with tetragonal structure at room temperature exhibit sharp ferroelectric to paraelectric phase transition. The PMW-xPT compositions with coexistence of tetragonal and cubic phases at room temperature exhibit two anomalies in the temperature dependence of the dielectric permittivity above room temperature. Using results of structural and dielectric studies a partial phase diagram of PMW-xPT ceramics is also presented.     

Structure and dielectric characterization of xNd(Mg1/2Ti1/2)O3-(1 − x)Ca0.6La0.8/3TiO3 in the microwave frequency range

The crystal structures, phase compositions and the microwave dielectric properties of the xLa(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.8Sr_0.2TiO₃ composites prepared by the conventional solid state route have been investigated. The formation of solid solution is confirmed by the XRD patterns. Doping with B₂O₃ (0.5 wt.%) can effectively promote the densification and the dielectric properties of xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics. It is found that xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics can be sintered at 1375 °C, due to the liquid phase effect of B₂O₃ addition observed by Scanning Electronic Microscopy. At 1375 °C, 0.4Nd(Mg_1/2Ti_1/2)O₃-0.6Ca_0.6La_0.8/3TiO₃ ceramics with 1 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 49, a Q × f value of 13,000 (at 8 GHz) and a temperature coefficients of resonant frequency (τ_f) of 1 ppm/°C. As the content of Nd(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 20,000 GHz for x = 0.9 is achieved at the sintering temperature 1400 °C.     

Crystal structure and dielectric properties of La(Mg1−xZnx)1/2Ti1/2O3 ceramics at microwave frequencies

Ceramics in the system La(Mg_1−xZn_x)_1/2Ti_1/2O₃ with B₂O₃ additions (1 wt.%) have been investigated by the conventional solid-state route. The XRD patterns of the sintered samples (0.3 ≤ x ≤ 1.0) revealed single phase formation with a structure. The unit cell volume slightly increased with increasing Zn content (x). La(Mg_1−xZn_x)_1/2Ti_1/2O₃ were found to form perovskite solid solutions in the whole compositional range. The maximum values of the dielectric constant and the quality factor multiples resonant frequency (Q × f) can be obtained when the La(Mg_0.7Zn_0.3)_1/2Ti_1/2O₃ with 0.5 wt.% B₂O₃ additive were sintered at 1475 °C for 4 h. The temperature coefficient of resonant frequency τ_f (−63 ppm/°C) was measured for x = 0.7.     

Relationships between Zr substitution for Ti and microwave dielectric properties in Mg(ZrxTi1−x)O3 ceramics

The influence of Zr substitution for Ti on the microwave dielectric properties and microstructures of the Mg(Zr_xTi_1−x)O₃(MZ_xT) (0.01 ≤ x ≤ 0.3) ceramics was investigated. The quality factors of Mg(Zr_xTi_1−x)O₃ ceramics with x = 0.01-0.05 were improved because the solid solution of a small amount of Zr⁴⁺ substitution in the B-site could increase density and grain size. An excess of Zr⁴⁺ resulted in the formation of a great deal of secondary phase that declined the microwave dielectric properties of MZ_xT ceramics. The temperature coefficient of resonant frequency (τ_f) of Mg(Zr_xTi_1−x)O₃ ceramics slightly increased with increasing Zr content, and the variation in τ_f was attributed to the formation of secondary phases.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Preparation and electrical properties of perovskite ceramics in the system BaBi1−xSbxO3 (0 ≤ x ≤ 0.5)

The effect of the composition on the electrical properties of BaBi_1−xSb_xO₃ (0 ≤ x ≤ 0.5) negative temperature coefficient (NTC) thermistors was studied. Major phases present in the sintered bodies of BaBi_1−xSb_xO₃ (0 < x < 0.5) ceramics were BaBi_0.5Sb_0.5O₃ compounds with a rhombohedral structure and BaBiO₃ compounds with a monoclinal structure. Most pores were located in the grains of BaBiO₃ and BaBi_0.5Sb_0.5O₃ ceramics. It was apparent that the ρ₂₅ and B_25/85 constant of the thermistors increased with increasing Sb content.     

Microwave properties of Ba(Zn1/3Ta2/3)O3 dielectric resonators

Ba(Zn_1/3Ta_2/3)O₃ (BZT) dielectric resonators were prepared by solid-state reaction. The starting materials were BaCO₃, ZnO, and Ta₂O₅ powders with high purity. The double calcined BZT pellets were sintered in air at temperatures of 1575, 1600, 1625, and 1650 °C for 4 h. The X-ray diffraction data allowed the study of the unit cell distortion degree and the presence of the secondary phases. A long-range order with a 2:1 ratio of Ta and Zn cations on the octahedral positions of the perovskite structure was observed with the increase of the sintering temperature. The dielectric constant of BZT resonators measured around 6 GHz was between 26 and 28. High values of Q × f product (120 THz) were obtained for BZT resonators sintered at 1650 °C/4 h. The temperature coefficient of the resonance frequency exhibits positive values less than 6 ppm/°C. The achieved dielectric parameters recommend BZT dielectric resonators for microwave and millimeter wave applications.     

Study of structural, dielectric and electrical behavior of (1 − x)Ba(Fe0.5Nb0.5)O3-xSrTiO3 ceramics

Polycrystalline samples of BaFe_0.5Nb_0.5O₃ and (1 − x)Ba(Fe_0.5Nb_0.5)O₃-xSrTiO₃ [referred as BFN and BFN-ST respectively] (x = 0.00, 0.15 and 0.20) have been synthesized by a high-temperature solid-state reaction technique. The XRD patterns of the BFN and BFN-ST at room temperature show a monoclinic phase. The microstructure of the ceramics was examined by the scanning electron microscopy (SEM) and shows the polycrystalline nature of the samples with different grain sizes, which are inhomogeneously distributed through the sample surface. Detailed studies of dielectric and impedance properties of the materials in a wide range of frequency (100 Hz-5 MHz) and temperatures (30-270 °C) showed that properties are strongly temperature and frequency dependent. Complex Argand plane plot of ?″ against ?′, usually called Cole-Cole plots is used to check the polydispersive nature of relaxation phenomena in above mentioned compounds. Relaxation phenomena of non-Debye type have been observed in the BFN and BFN-ST ceramics, as confirmed by the Cole-Cole plots.     

Characterization of sol-gel synthesised lead-free (1 − x)Na0.5Bi0.5TiO3-xBaTiO3-based ceramics

The crystal structure, microstructure, dielectric and ferroelectric properties of (1 − x)Na_0.5Bi_0.5TiO₃-xBaTiO₃ ceramics with x = 0, 0.03, 0.05, 0.07 and 0.1 are investigated. A structural variation according to the system composition was investigated by X-ray diffraction (XRD) analyses. The results revealed that the synthesis temperature for pure perovskite phase powder prepared by the present sol-gel process is much lower (800 °C), and a rhombohedral-tetragonal morphotropic phase boundary (MPB) is found for x = 0.07 composition which showing the highest remanent polarization value and the smallest coercive field. The optimum dielectric and piezoelectric properties were found with the 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃ composition. The piezoelectric constant d₃₃ is 120 pC/N and good polarization behaviour was observed with remanent polarization (P_r) of 12.18 pC/cm², coercive field (E_c) of 2.11 kV/mm, and enhanced dielectric properties ?_r > 1500 at room temperature. The 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃-based ceramic is a promising lead-free piezoelectric candidate for applications in different devices.     

Crystal structure and microwave dielectric properties of ZnTi(Nb1−xTax)2O8 ceramics

The crystal structure and microwave dielectric properties of ZnTi(Nb_1−xTa_x)₂O₈ (0 ≤ x ≤ 1) ceramics sintered at 1200 °C for 2 h were investigated. For x < 0.5, solid solution phases with the α-PbO₂ structure, typical of ZnTiNb₂O₈, were obtained, whereas for 0.5 ≤ x < 1, mixtures of two solid solutions each respectively based on the α-PbO₂ structure and a trirutile structure, were obtained. The relative amount of the trirutile-structured phases increased as the Ta content increased in a given region, and the end member ZnTiTa₂O₈ formed a single phase with the trirutile structure. The microwave dielectric properties were closely related to the crystal structures. A material with a near zero temperature coefficient of resonant frequency could be obtained for x = 0.8, and its dielectric constant and quality factor (Q × f) were 40.5 and 41,000 GHz, respectively.     

Infrared emissivities and microwave absorption properties of perovskite Sm0.5Sr0.5Co1−xFexO3 (0 ≤ x ≤ 0.5)

Sm_0.5Sr_0.5Co_1−xFe_xO₃ (0 ≤ x ≤ 0.5, SSCF) with perovskite-type structure has been successfully prepared by conventional solid-state reaction as a microwave and infrared multi-functional material. The effects of Fe incorporation on the structure, electrical conductivity, infrared emissivity and microwave-absorbing properties were investigated in detail. XRD results have shown that the perovskite structure of SSCF has an orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5, respectively. The incorporation of Fe in SSCF could contribute to the decrease of electrical conductivity, while the infrared emissivities are increased. Moreover, microwave-absorbing properties in the frequency range of 2-18 GHz at room temperature are sensitive to Fe content. The complex permittivity, complex permeability and electromagnetic loss tangent have suddenly a step change at a certain frequency and the step-change frequency position moves slightly to lower frequencies with Fe increased. The optimal reflection loss calculated from the measured permittivity and permeability is 29.33 dB at 7.97 GHz with a thickness of 2.0 mm.     

High-Q microwave dielectrics in the (Mg1−xZnx)Al2O4 (x = 0-0.1) system

The microwave dielectric properties and the microstructures of (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) ceramic system prepared by the conventional solid-state route were investigated. The forming of spinel-structured (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) solid solutions was confirmed by the XRD patterns and the measured lattice parameters, which linearly varied from a = b = c = 8.0815 Å for MgAl₂O₄ to a = b = c= 8.0828 Å for (Mg_0.9Zn_0.1)Al₂O₄. By increasing x, the Q × f of (Mg_1−xZn_x)Al₂O₄ can be tremendously boosted from 82,000 GHz at x = 0 to a maximum of 156,000 GHz at x = 0.05. The Zn substitution was effective in reducing the dielectric loss without detrimental effects on the ?_r and τ_f values of the ceramics.     

Dielectric properties and crystal structure of La(Mg1/2Ti1/2)O3 ceramics with Mg substituted by Co

Solid solutions of (1 − x)La(Co_1/2Ti_1/2)O₃-xLa(Mg_1/2Ti_1/2)O₃ were used to prepare La(Mg_1−xCo_x)_1/2Ti_1/2O₃ using solid-state synthesis. X-ray diffraction patterns of the sintered samples revealed single phase formation. A maximum density of 6.01 g/cm³ was obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ (x = 1) ceramics sintered at 1375 °C for 4 h. The maximum values of the dielectric constant (?_r = 29.13) and the quality factor (Q × f = 80,000 GHz) were obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ with 1 wt% ZnO additive sintered at 1375 °C for 4 h. The temperature coefficient of resonant frequency τ_f was −59 ppm/°C for x = 0.3.     

Effect of addition of Ba(W0.5Cu0.5)O3 in Pb(Mg1/3Nb2/3)O3-Pb(Zn1/3Nb2/3)O3-Pb(Zr0.52Ti0.48)O3 ceramics on the sintering temperature, electrical properties and phase transition

In this work, we report on the Pb(Mg_1/3Nb_2/3)O₃-Pb(Zn_1/3Nb_2/3)O₃-Pb(Zr_0.52Ti_0.48)O₃ (PMN-PZN-PZT) ceramics with Ba(W_0.5Cu_0.5)O₃ as the sintering aid that was manufactured in order to develop the low-temperature sintering materials for piezoelectric device applications. The phase transition, microstructure, dielectric, piezoelectric properties, and the temperature stability of the ceramics were investigated. The results showed that the addition of Ba(W_0.5Cu_0.5)O₃ significantly improved the sintering temperature of PMN-PZN-PZT ceramics and could lower the sintering temperature from 1005 to 920 °C. Besides, the obtained Ba(W_0.5Cu_0.5)O₃-doped ceramics sintered at 920 °C have optimized electrical properties, which are listed as follows: (K_p = 0.63, Q_m = 1415 and d₃₃ = 351 pC/N), and high depolarization temperature above 320 °C. These results indicated that this material was a promising candidate for high-power multilayer piezoelectric device applications.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting Mg with Ni

The microwave dielectric properties of La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method at various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.71 g/cm³, dielectric constant (?_r) of 20.19, quality factor (Q × f) of 74,600 GHz, and temperature coefficient of resonant frequency (τ_f) of −85 ppm/°C were obtained for La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Influence of A-site Gd doping on the microstructure and dielectric properties of Ba(Zr0.1Ti0.9)O3 ceramics

Pure and Gd-doped barium zirconate titanate (BaZr_0.1Ti_0.9O₃, BZT) ceramics were prepared by solid state reaction method. Phase analysis showed the formation of the pyrochlore phase (Gd₂Ti₂O₇) at about 5 mol% Gd doping in BZT. The microstructural investigation on the sintered ceramics showed that Gd doping significantly reduced the grain size of pure BZT ceramics, from about 100 μm to 2-5 μm. Change in the Gd concentration had minor influence on the grain size and on morphology. An increase in the Gd content decreased the Curie temperature (T_C) of the BZT ceramics. The maximum dielectric constant at T_C was observed for 2 mol% Gd and with further increase in Gd content the dielectric constant at T_C decreased. The dielectric constant was significantly improved compared to that of pure BZT ceramic. Tunable dielectric materials with good dielectric properties can be prepared by doping BZT with Gd.     

Improving the piezoelectric thermal stability by tailoring phase transition behavior in the new (1 − x)[0.65PbMg1/3Nb2/3O3-0.35PbTiO3]-xBiZn1/2Ti1/2O3 perovskite solid solutions

The phase transition behavior and its effect on thermal stability of the piezoelectric properties of the (1 − x)[0.65PbMg_1/3Nb_2/3O₃-0.35PbTiO₃]-xBiZn_1/2Ti_1/2O₃ ceramics with 0 ≤ x ≤ 0.06 were investigated. The phase transition from the monoclinic to tetragonal phase was determined by the dielectric constant and elastic constant measurements. The temperature independent piezoelectric response with −d₃₁ = 188 pC/N was obtained from 175 to 337 K for the composition with x = 0.02. The enhanced thermal stability of piezoelectric response was achieved by shifting the monoclinic-tetragonal phase transition to the lower temperature.     

Microstructure, ferroelectric, and piezoelectric properties of (1 − x − y)Bi0.5Na0.5TiO3-xBaTiO3-yBi0.5Ag0.5TiO3 lead-free ceramics

Lead-free (1 − x − y)Bi_0.5Na_0.5TiO₃-xBaTiO₃-yBi_0.5Ag_0.5TiO₃ (BNT-BT-BAT-x/y, x = 0-0.10, y = 0-0.075) piezoelectric ceramics were synthesized by conventional oxide-mixed method. The microstructure, ferroelectric, and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases of BNT-BT-BAT-x/0.04 ceramics is formed at x = 0.06-0.08. The addition of BAT has no obvious change on the crystal structure of BNT-BT ceramics while it causes the grain size of the ceramics to become more homogenous. Near the MPB, the ceramics with x = 0.06 and y = 0.05-0.06 possess optimum electrical properties: P_r ∼ 42.5 μC/cm², E_c ∼ 32.0 kV/cm, d₃₃ ∼ 172 pC/N, k_p ∼ 32.6%, and k_t ∼ 52.6%. The temperature dependences of k_p and polarization versus electric hysteresis loops reveal that the depolarization temperature (T_d) of BNT-BT-BAT-0.06/y ceramics decreases with increasing y. In addition, the polar and non-polar phases may coexist in the BNT-BT-BAT-x/y ceramics above T_d.     

Structure, dielectric and electric properties of (Ba0.68−xSr0.308Bi0.006Na0.006Mgx)(Ti0.99Sn0.01)O3 ceramics

(Ba_0.68−xSr_0.308Bi_0.006Na_0.006Mg_x)(Ti_0.99Sn_0.01)O₃ ceramics were synthesized by solid-state reaction process. The samples (X ≤ 0.010) are a mixture of cubic (major) and rhombohedral (minor) phases. The rhombohedral phase causes a large dielectric loss in low temperature regions and plays an important role in diffuse phase transition of ceramics. While X > 0.010, the rhombohedral phase decreases and gradually disappears. The dielectric loss of ceramics in the low temperature regions decreases, and the samples change from the diffuse phase transition to the phase transition of second order, and then to of first order. In the temperature range of 270-370 °C, intrinsic conduction dominates conductivity of ceramics.