Structural parameters and oxygen ion conductivity of Y2O3–ZrO2 and MgO–ZrO2 at high temperature

The oxygen ion conductivity of zirconia-based solid electrolytes doped with 8 mol% Y₂O₃–ZrO₂ (YSZ) and 9 mol% MgO–ZrO₂ (Mg-PSZ) at high temperature was investigated in terms of their thermal behavior and structural changes. At room temperature, YSZ showed a single phase with a fluorite cubic structure, whereas Mg-PSZ had a mixture of cubic, tetragonal and some monoclinic phases. YSZ exhibited higher ionic conductivity than Mg-PSZ at temperatures from 600 °C to 1250 °C because of the existence of the single cubic structure and low activation energy. A considerable increase in the conductivity with increasing temperature was observed in Mg-PSZ, which showed higher ionic conductivity than YSZ within the higher temperature range of 1300–1500 °C. A monoclinic-to-tetragonal phase transformation was found in Mg-PSZ and the lattice parameter of the cubic phase increased at 1200 °C. The phase transformation and the large lattice free volume contributed to the significant enhancement of the ionic conductivity of Mg-PSZ at high temperatures.     

Effect of sintering temperature on microstructure and mechanical properties of zirconia-toughened alumina machinable dental ceramics

This study investigated the effect of sintering temperature on the microstructure and mechanical properties of dental zirconia-toughened alumina (ZTA) machinable ceramics. Six groups of gelcast ZTA ceramic samples sintered at temperatures between 1100 °C and 1450 °C were prepared. The microstructure was investigated by mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and scanning electron microscopy (SEM) techniques. The mechanical properties were characterized by flexural strength, fracture toughness, Vickers hardness, and machinability. Overall, with increasing temperature, the relative density, flexural strength, fracture toughness, and Vickers hardness values increased and more tetragonal ZrO₂ transformed into monoclinic ZrO₂; on the other hand, the porosity and pore size decreased. Significantly lower brittleness indexes were observed in groups sintered below 1300 °C, and the lowest values were observed at 1200 °C. The highest flexural strength and fracture toughness of ceramics reached 348.27 MPa and 5.23 MPa m^1/2 when sintered at 1450 °C, respectively. By considering the various properties of gelcast ZTA that varied with the sintering temperature, the optimal temperature for excellent machinability was determined to be approximately 1200–1250 °C, and in this range, a low brittleness index and moderate strength of 0.74–1.19 µm^−1/2 and 46.89–120.15 MPa, respectively, were realized.     

Electrical properties and microstructural evolution of ZrO2–Al2O3–TiN nanocomposites prepared by spark plasma sintering

Electroconductive ZrO₂–Al₂O₃–25 vol% TiN ceramic nanocomposites were prepared by spark plasma sintering at 1200 °C for 3 min. The electrical resistivity of the composites decreased from 4.5 × 10^?4 Ω m to 3 × 10^?5 Ω m as the Al₂O₃ content in the ZrO₂–Al₂O₃ matrix increased from 0 to 100 vol%. SEM images graphically presented the microstructural evolution of the composites and a geometrical percolation model was applied to investigate the relationship between the electrical property and the microstructure. The results indicated that the addition of Al₂O₃ to ZrO₂–TiN improved the electrical conductivity of the material by tailoring the structure from “nano–nano” type for ZrO₂–TiN to “micro–nano” type for ZrO₂–Al₂O₃–TiN.     

Effects of microstructure evolution on transport properties of thermoelectric nickel-doped zinc oxide

We investigate the effects of microstructure evolution on transport properties of nickel-doped ZnO for thermoelectric waste heat recovery at high temperatures. A 3 at.% supersaturated Ni-alloyed ZnO solid solution was prepared by sintering at 1400 °C followed by controlled nucleation and growth of sub-micrometer size NiO-precipitates by aging at 750, 800, and 900 °C for different durations. Minimum thermal conductivity as low as 8.0 W m⁻¹ K⁻¹ at 700 °C is obtained for samples aged at 750 °C for 16 h due to precipitates with high number density of 1.3·10²⁰ m⁻³, which initiate phonon scattering. In turn, as-quenched samples exhibit the highest electrical conductivity, ca. 17.9 S cm⁻¹ at 700 °C. Further nucleation and growth of precipitates taking place for longer annealing durations reduce electrical conductivity and increase Seebeck coefficients, which is associated with dilution of the ZnO-matrix from Ni-atoms. This study provides us with guidelines for optimization of thermoelectric Ni-doped ZnO.     

One-pot synthesis of monoclinic ZrO2 nanocrystals under subcritical hydrothermal conditions

This study reports a one-pot synthesis technique for the preparation of single-phase monoclinic zirconium oxide (ZrO₂) nanocrystals. The products were synthesized from only zirconium oxynitrate (ZrO(NO₃)₂) as the precursor under hydrothermal conditions using subcritical water. The precursor was heat-treated in a batch-type reactor at a reaction temperature of 250 °C for 24 h to obtain pure monoclinic-structured ZrO₂ nanocrystals. The crystallization temperature of the ZrO₂ phase was also greater than 200 °C. However, the products of reactions conducted at 200 °C for 24 h were mixtures of the tetragonal and monoclinic structures. At a reaction temperature of 250 °C, the volume fraction of the monoclinic phase increased; however, the reaction time was also important. The heat-treatment was performed for more than 12 h in order to obtain single-phase monoclinic ZrO₂ nanocrystals. The crystallite size of this product was approximately 20 nm, and water, hydroxide groups, and nitro groups were chemisorbed on its surface.     

High Li-ion conductivity of Al-doped Li7La3Zr2O12 synthesized by solid-state reaction

Li₇La₃Zr₂O₁₂ (LLZO) has cubic garnet type structure and is a promising solid electrolyte for next-generation Li-ion batteries. In this work, Al-doped LLZO was prepared via conventional solid-state reaction. The effects of sintering temperature and Al doping content on the structure and Li-ion conductivity of LLZO were investigated. The phase composition of the products was confirmed to be cubic LLZO via XRD. The morphology and chemical composition of calcined powders were investigated with SEM, EDS, and TEM. The Li-ion conductivity was measured by AC impedance. The results indicated the optimum sintering temperature range is 800–950 °C, the appropriate molar ratio of LiOH·H₂O, La(OH)₃, ZrO₂ and Al₂O₃ is 7.7:3:2:(0.2–0.4), and the Li-ion conductivity of LLZO sintered at 900 °C with 0.3 mol of Al-doped was 2.11×10⁻⁴ S cm⁻¹ at 25 °C.     

Structural,optical, and electrical properties of conducting p-type transparent Cu–Cr–O thin films

Cu–Cr–O films were prepared by DC magnetron co-sputtering using Cu and Cr targets on quartz substrates. The films were then annealed at temperatures ranging from 400 °C to 900 °C for 2 h under a controlled Ar atmosphere. The as-deposited and 400 °C-annealed films were amorphous, semi-transparent, and insulated. After annealing at 500 °C, the Cu–Cr–O films contained a mixture of monoclinic CuO and spinel CuCr₂O₄ phases. Annealing at 600 °C led to the formation of delafossite CuCrO₂ phases. When the annealing was further increased to temperatures above 700 °C, the films exhibited a pure delafossite CuCrO₂ phase. The crystallinity and grain size also increased with the annealing temperature. The formation of the delafossite CuCrO₂ phase during post-annealing processing was in good agreement with thermodynamics. The optimum conductivity and transparency were achieved for the film annealed at approximately 700 °C with a figure of merit of 1.51×10⁻⁸ Ω⁻¹ (i.e., electrical resistivity of up to 5.13 Ω-cm and visible light transmittance of up to 58.3%). The lower formation temperature and superior properties of CuCrO₂ found in this study indicated the higher potential of this material for practical applications compared to CuAlO₂.     

Effect of pre-oxidation on the microstructure,mechanical and dielectric properties of highly porous silicon nitride ceramics

Highly porous Si₃N₄ ceramics have been fabricated via freeze casting and sintering. The as-sintered samples were pre-oxidized at 1200–1400 °C for 15 min. The effect of pre-oxidation temperature on the microstructure, flexural strength, and dielectric properties of porous Si₃N₄ ceramics were investigated. As the pre-oxidation temperature increased from 1200 °C to 1400 °C, firstly, the flexural strength of the pre-oxidized specimens remained almost constant at 1200 °C, and then decreased to 14.2 MPa at 1300 °C, but finally increased to 25.6 MPa at 1400 °C, while the dielectric constant decreased gradually over the frequencies ranging from 8.2 GHz to 12.4 GHz. This simple process allows porous Si₃N₄ ceramics to have ultra-low dielectric constant and moderate strength, which will be feasible in broadband radome applications at high temperatures.     

Electrochemical and microstructural characteristics of nanoperovskite oxides Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF) for solid oxide fuel cells

Nanoperovskite oxides, Ba_0.2Sr_0.8Co_0.8Fe_0.2O_3?δ (BSCF), were synthesized via the co-precipitation method using Ba, Sr, Co, and Fe nitrates as precursors. Next, half cells were fabricated by painting BSCF thin film on Sm_0.2Ce_0.8O_x (samarium doped ceria, SDC) electrolyte pellets. X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electrochemical impedance spectroscopy (EIS) measurements were carried out on the BSCF powders and pellets obtained after sintering at 900 °C. Investigations revealed that single-phase perovskites with cubic structure was obtained in this study. The impedance spectra for BSCF/SDC/BSCF cells were measured to obtain the interfacial area specific resistances (ASR) at several operating temperatures. The lowest values of ASR were found to be 0.19 Ω cm², 0.14 Ω cm² 0.10 cm², 0.09 Ω cm² and 0.07 Ω cm² at operating temperatures of 600 °C, 650 °C, 700 °C, 750 °C and 800 °C, respectively. The highest conductivity was found for cells sintered at 900 °C with an electrical conductivity of 153 S cm^?1 in air at operating temperature of 700 °C.     

Fabrication and evaluation of NiO/Y2O3-stabilized-ZrO2 hollow fibers for anode-supported micro-tubular solid oxide fuel cells

In this work NiO/3 mol% Y₂O₃–ZrO₂ (3YSZ) and NiO/8 mol% Y₂O₃–ZrO₂ (8YSZ) hollow fibers were prepared by phase-inversion. The effect of different kinds of YSZ (3YSZ and 8YSZ) on the porosity, electrical conductivity, shrinkage and flexural strength of the hollow fibers were systematically evaluated. When compared with Ni–8YSZ the porosity and shrinkage of Ni–3YSZ hollow fibers increases while the electrical conductivity decreases, while at the same time also exhibiting enhanced flexural strength. Single cells with Ni–3YSZ and Ni–8YSZ hollow fibers as the supported anode were successfully fabricated showing maximum power densities of 0.53 and 0.67 W cm⁻² at 800 °C, respectively. Furthermore, in order to improve the cell performance, a Ni–8YSZ anode functional layer was added between the electrolyte and Ni–YSZ hollow fiber. Here enhanced peak power densities of 0.79 and 0.73 W cm⁻² were achieved at 800 °C for single cells with Ni–3YSZ and Ni–8YSZ hollow fibers, respectively.     

Synthesis of homoallyl alcohol from 1,4-butanediol over ZrO2 catalyst

Catalytic dehydration of 1,4-butanediol was investigated over ZrO₂ with monoclinic crystal phase at temperatures of 275–425 °C. In the reaction, 3-buten-1-ol was effectively produced together with tetrahydrofuran (THF) over ZrO₂ at 300–375 °C. 3-Buten-1-ol and THF were produced competitively, and the yield of 3-buten-1-ol increased with increasing the contact time. Formation of by-products such as 2-buten-1-ol, 2-butenal, and 1-butanol was suppressed over ZrO₂ at 325 °C.     

Microstructure and thermophysical properties of B4C/graphite composites containing substitutional boron

B₄C/graphite composites (BGC) containing substitutional boron were fabricated by pressureless sintering of powder mixtures of petroleum coke, coal tar pitch and B₄C. After sintering at 900 °C and graphitizing at 2200 °C, the microstructure of BGC was characterized by SEM, TEM, XRD, Raman spectroscopy and optical microscopy. XPS measurements revealed the formation of BC₃, and the matrix carbon contained around 6 wt.% substitutional boron. The thermal conductivity of the BGC at room temperature is 52.7 W/m K and the flexural strength is up to 35.1 MPa. The bulk density and electrical resistivity are 1.72 g/cm³ and 13.4 μΩ m, respectively. The correlation between microstructure and properties was investigated. The results showed that the microstructure improvement of the BGC has obvious effect on the thermal conductivity, flexural strength, and electrical resistivity.     

Synthesis of zirconium diboride platelets from mechanically activated ZrCl4 and B powder mixture

ZrB₂ platelets were prepared by mechanochemical processing a zirconium (IV) chloride–boron mixture with subsequent annealing from 800 °C to 1200 °C. The phases present were identified by X-ray diffraction. The size and morphology of the synthesized ZrB₂ powders were characterized by scanning electron and transmission electron microscopy. At 800 °C, ZrO₂ was detected in absence of ZrB₂. At or above 1000 °C, ZrCl₄–B converted to ZrB₂. Moreover, at 1200 °C, ZrCl₄–B completely converted to ZrB₂ without trace quantities of residual ZrO₂. The synthesized ZrB₂ consisted of platelets with a diameter of 0.1–2.1 μm and a thickness of 40–200 nm.     

Microstructure and mechanical properties of Al2O3/Y3Al5O12/ZrO2 ternary eutectic materials

Directionally solidified fibers and rods have been grown from the ternary Al₂O₃/Y₃Al₅O₁₂/ZrO₂ system using micro-pulling-down method. Fiber diameter could be varied 0.3 mm–2 mm at pull-rates ranging 6–900 mm/h and 500 mm in length. The ternary eutectic fibers had homogeneous colony patterned eutectic microstructures. The interlamellar spacing λ exhibited an inverse-square-root dependence on the growth speed v according to λ = 8 × v^−1/2, where λ has the dimension of μm and v is in μm/s. The tensile strength was recorded 1730 MPa at 25 °C and 1100 MPa at 1200 °C for a fiber crystals grown at a growth speed of 900 mm/h. Eutectic rods having 5 mm of diameter and up to 80 mm in length were also successfully grown by the micro-pulling-down method. The eutectic rods showed 1400 MPa of mechanical strength by compressive mode at 1500 °C with homogeneous colony microstructures.     

Characteristics of samaria-doped ceria nanoparticles prepared by spray pyrolysis

Samaria-doped ceria (SDC) nanoparticles were prepared by spray pyrolysis. The means sizes of the samaria-doped ceria nanoparticles were controlled from 21 to 150 nm by changing the calcination temperatures between 700 and 1200 °C. The pellets formed from the SDC particles calcined at temperatures between 700 and 1000 °C had similar grain sizes between 0.75 and 0.82 μm. However, pellet formed from the SDC particles calcined at a temperature of 1200 °C had large grain size of 1.22 μm. The pellet formed from the SDC particles calcined at a temperature of 1000 °C had slightly smaller resistance of grain-boundary than those of the pellets formed from the SDC particles calcined at temperatures between 700 and 900 °C. However, the pellet formed from the SDC particles calcined at a temperature of 1200 °C had low resistance of grain-boundary. The pellet formed from the SDC particles calcined at a temperature of 1200 °C had conductivity of 44.65 × 10^?3 S cm^?1 at a measuring temperature of 700 °C that more twice than those of the pellets formed from the SDC calcined below 1000 °C.     

Synthesis and pyrolysis behavior of a soluble polymer precursor for ultra-fine zirconium carbide powders

A soluble polymer precursor for ultra-fine zirconium carbide (ZrC) was successfully synthesized using phenol and zirconium tetrachloride as carbon and zirconium sources, respectively. The pyrolysis behavior and structural evolution of the precursor were studied by Fourier transform infrared spectra (FTIR), differential scanning calorimetry, and thermal gravimetric analysis (DSC–TG). The microstructure and composition of the pyrolysis products were characterized by X-ray diffraction (XRD), laser Raman spectroscopy, scanning electron microscope (SEM) and element analysis. The results indicate that the obtained precursor for the ultra-fine ZrC could be a Zr–O–C chain polymer with phenol and acetylacetone as ligands. The pyrolysis products of the precursor mainly consist of intimately mixed amorphous carbon and tetragonal ZrO₂ (t-ZrO₂) in the temperature range of 300–1200 °C. When the pyrolysis temperature rises up to 1300 °C, the precursor starts to transform gradually into ZrC, accompanied by the formation of monoclinic ZrO₂ (m-ZrO₂). The carbothermal reduction reaction between ZrO₂ and carbon has been substantially completed at a relatively low temperature (1500 °C). The obtained ultra-fine ZrC powders exhibit as well-distributed near-spherical grains with sizes ranging from 50 to 100 nm. The amount of oxygen in the ZrC powders could be further reduced by increasing the pyrolysis temperature from 1500 to 1600 °C but unfortunately the obvious agglomeration of the ZrC grains will be induced.     

Mechanical properties of Hi-Nicalon fiber-reinforced celsian composites after high-temperature exposures in air

BN/SiC-coated Hi-Nicalon fiber-reinforced celsian matrix composites (CMCs) were annealed for 100 h in air at various temperatures to 1200 °C, followed by flexural strength measurements at room temperature. Values of yield stress and strain, ultimate strength, and composite modulus remain almost unchanged for samples annealed up to 1100 °C. A thin porous layer formed on the surface of the 1100 °C annealed sample and its density decreased from 3.09 to 2.90 g/cm³. The specimen annealed at 1200 °C gained 0.43% weight, was severely deformed, and was covered with a porous layer of thick shiny glaze which could be easily peeled off. Some gas bubbles were also present on the surface. This surface layer consisted of elongated crystals of monoclinic celsian and some amorphous phase(s). The fibers in this surface ply of the CMC had broken into small pieces. The fiber–matrix interface strength was characterized through fiber push-in technique. Values of debond stress, σ_d, and frictional sliding stress, τ_f, for the as-fabricated CMC were 0.31 ± 0.14 GPa and 10.4 ± 3.1 MPa, respectively. These values compared with 0.53 ± 0.47 GPa and 8.33 ± 1.72 MPa for the fibers in the interior of the 1200 °C annealed sample, indicating hardly any change in fiber–matrix interface strength. The effects of thermal aging on microstructure were investigated using scanning electron microscopy. Only the surface ply of the 1200 °C annealed specimens had degraded from oxidation whereas the bulk interior part of the CMC was unaffected. A mechanism is proposed explaining the various steps involved during the degradation of the CMC on annealing in air at 1200 °C.     

Molten salt attack on t′ yttria-stabilised zirconia by dissolution and precipitation

Degradation due to molten salt attack is one of the failure mechanisms of thermal barrier coatings. Thermochemical attack of the salt mixture Na₂SO₄–30 mol% NaVO₃ on ZrO₂–8 mol% YO_1.5 (8YSZ) at 950 °C was studied by two types of experiments. Sintered compacts were exposed to 25 mg cm^?2 salt dosage for up to 96 h. In the other set of experiments, 10–35 wt.% 8YSZ powder was mixed with the salts to study the dissolution of 8YSZ in the molten salt. The role of volatile losses was also examined. The results show that more than 25 wt.% 8YSZ dissolves in the sulphate-vanadate melt at 950 °C, followed by slow reactions to form YVO₄ and NaYV₂O₇ at 950 °C. The unreacted Y₂O₃ and monoclinic ZrO₂ precipitate out separately during rapid cooling (～300 °C/min). Slow cooling at ～3 °C/min leads to the formation of ZrOS apart from ZrO₂ and Y₂O₃.     

Effect of sintering temperature on the structural,electrical and electrochemical properties of novel Mg0.5Si2 (PO4)3 ceramic electrolytes

The objective of the present study is to investigate the effect of sintering temperature on the structural, electrical and electrochemical properties of novel Mg_0.5Si₂ (PO₄) ₃ NASICON structured compound prepared via sol gel method. X-ray diffraction was used to study the structural properties such as crystalline phase and lattice parameters of the solid electrolytes. Electrical properties of the compound were measured using impedance spectroscopy while the electrochemical stability was investigated by linear sweep voltammetry. All the sintering temperatures yielded compounds consisted of monoclinic crystalline phase with a space group of P1 2₁/c1. Lattice parameters for Mg_0.5Si₂ (PO₄) ₃ samples increased from the sintering temperature at 700–800 °C but decreased for sintering temperature at 900 °C. The sample sintered at 800 °C showed the highest total conductivity of 1.83×10⁻⁵ S cm⁻¹ and the highest value of ions mobility, µ of 6.17×10¹⁰ cm² V⁻¹ s⁻¹ which was attributed to the optimum size of migration channel indicated by its unit cell volume. Linear sweep voltammetry result showed that the Mg_0.5Si₂ (PO₄)₃ powder was electrochemically stable up to 3.21 V.     

Effect of Nd-doping on structural,thermal and electrochemical properties of LaFe0.5Cr0.5O3 perovskites

The structural, thermal and electrochemical properties of the perovskite-type compound La_1−xNd_xFe_0.5Cr_0.5O₃ (x=0.10, 0.15, 0.20) are investigated by X-ray diffraction, thermal expansion, thermal diffusion, thermal conductivity and impedance spectroscopy measurements. Rietveld refinement shows that the compounds crystallize with orthorhombic symmetry in the space group Pbnm. The average thermal expansion coefficient decreases as the content of Nd increases. The average coefficient of thermal expansion in the temperature range of 30–850 °C is 10.12×10⁻⁶, 9.48×10⁻⁶ and 7.51×10⁻⁶ °C⁻¹ for samples with x=0.1, 0.15 and 0.2, respectively. Thermogravimetric analyses show small weight gain at high temperatures which correspond to filling up of oxygen vacancies as well as the valence change of the transition metals. The electrical conductivity measured by four-probe method shows that the conductivity increases with the content of Nd; the electrical conductivity at 520 °C is about 4.71×10⁻³, 6.59×10⁻³ and 9.62×10⁻³ S cm⁻¹ for samples with x=0.10, 0.15 and 0.20, respectively. The thermal diffusivity of the samples decreases monotonically as temperature increases. At 600 °C, the thermal diffusivity is 0.00425, 0.00455 and 0.00485 cm² s⁻¹ for samples with x=0.10, 0.15 and 0.20, respectively. Impedance measurements in symmetrical cell arrangement in air reveal that the polarization resistance decreases from 55 Ω cm⁻² to 22.5 Ω cm⁻² for increasing temperature from 800 °C to 900 °C, respectively.