Reduced chemically modified graphene oxide for supercapacitor electrode

An efficient active material for supercapacitor electrodes is prepared by reacting potassium hydroxide (KOH) with graphene oxide followed by chemical reduction with hydrazine. The electrochemical performance of KOH treated graphene oxide reduced for 24 h (reduced chemically modified graphene oxide, RCMGO-24) exhibits a specific capacitance of 253 F g^-1 at 0.2 A g^-1 in 2 M H₂SO₄ compared to a value of 141 F g^-1 for graphene oxide reduced for 24 h (RGO-24), and good cyclic stability up to 3,000 cycles. Interestingly, RCMGO-24 demonstrated a higher specific capacitance and excellent cycle stability due to its residual oxygen functional groups that accelerate the faradaic reactions and aid in faster wetting. This non-annealed strategy offers the potential for simple and cost-effective preparation of an active material for a supercapacitor electrode.     

Synthesis of reduced graphene oxide/tungsten trioxide nanocomposite electrode for high electrochemical performance

A facile and well-controllable reduced graphene oxide/tungsten trioxide (rGO/WO₃) nanocomposite electrode was successfully synthesized via an electrostatic assembly route at 350 rpm for 24 h. In this study, hexagonal-phase WO₃ (h-WO₃) nanofiber was well distributed on rGO sheets by applying optimal processing parameters. The as-synthesized rGO/WO₃ nanocomposite electrode was compared with pure h-WO₃ electrode. A maximum specific capacitance of 85.7 F g⁻¹ at a current density of 0.7 A g⁻¹ was obtained for the rGO/WO₃ nanocomposite electrode, which showed better electrochemical performance than the WO₃ electrode. The incorporation of WO₃ into rGO could prevent the restacking of rGO and provide favourable surface adsorption sites for intercalation/de-intercalation reactions. The impedance studies demonstrated that the rGO/WO₃ nanocomposite electrode exhibited lower resistance because of the superior conductivity of rGO that improved ion diffusion into the electrode. To evaluate the contribution of WO₃ to the rGO/WO₃ nanocomposite, the influence of mass loading of WO₃ on the capacitance was investigated.     

A flexible graphene/multiwalled carbon nanotube film as a high performance electrode material for supercapacitors

A flexible graphene/multiwalled carbon nanotube (GN/MWCNT) film has been fabricated by flow-directed assembly from a complex dispersion of graphite oxide (GO) and pristine MWCNTs followed by the use of gas-based hydrazine to reduce the GO into GN sheets. The GN/MWCNT (16 wt.% MWCNTs) film characterized by Fourier transformation infrared spectra, X-ray diffraction and scanning electron microscope has a layered structure with MWCNTs uniformly sandwiched between the GN sheets. The MWCNTs in the obtained composite film not only efficiently increase the basal spacing but also bridge the defects for electron transfer between GN sheets, increasing electrolyte/electrode contact area and facilitating transportation of electrolyte ion and electron into the inner region of electrode. Electrochemical data demonstrate that the GN/MWCNT film possesses a specific capacitance of 265 F g⁻¹ at 0.1 A g⁻¹ and a good rate capability (49% capacity retention at 50 A g⁻¹), and displays an excellent specific capacitance retention of 97% after 2000 continuous charge/discharge cycles. The results of electrochemical measurements indicate that the freestanding GN/MWCNT film has a potential application in flexible energy storage devices.     

Simultaneously morphology and phase controlled synthesis of cobalt manganese hydroxides/reduced graphene oxide for high performance supercapacitor electrodes

Cobalt manganese hydroxides with well-defined nanowire morphology (CoMn-HW) is scalable fabricated by adjusting solution contents, Mn/Co ratio and alkaline species. To further improve the conductivity of CoMn-HW, GO is introduced during fabrication process and reduced to rGO according to the high temperature and alkali atmosphere. By optimizing the adding mass of rGO, CoMn-HW/rGO with sandwiched like structure is successfully synthesized for supercapacitor electrode. The composite delivers a high specific capacitance of 784 F g⁻¹ at current density of 0.5 A g⁻¹, good rate capability (84.2% capacitance retention after current density increase 10 times). Moreover, an asymmetric supercapacitor with CoMn-HW/rGO10 as the positive electrode and active carbon as the negative electrode, is assembled and delivers a maximum energy density of 38.3 Wh kg⁻¹ and power density of 8000 W kg⁻¹, representing its potential in energy storage and conversion systems.     

Synthesis of graphene/vitamin C template-controlled polyaniline nanotubes composite for high performance supercapacitor electrode

A graphene nanosheet/polyaniline nanotube (GPNT) composite is prepared for the first time by in-situ chemical oxidative polymerization of aniline using vitamin C as a structure directing agent. The vitamin C molecules lead to the synthesis of polyaniline (PANI) nanotubes through the development of rod-like assembly by H-bonding in an aqueous medium. The initially synthesized graphene oxide/polyaniline nanotubes composite is reduced to graphene using hydrazine monohydrate followed by re-oxidation and protonation of the PANI to produce the GPNT nanocomposite. This novel composite showed a high specific capacitance of 534.37 F/g and an excellent energy density of 74.27 Wh/kg at a constant current of 0.5 mA. Besides, the GPNT composite exhibited excellent cycle life with 91.4% specific capacitance retained after 500 charge-discharge cycles. The excellent performance is due to the synergistic combination of graphene which provides good electrical conductivity and mechanical stability, and PANI nanofiber which deals with good redox activity.     

Facile synthesis of reduced graphene oxide/CeO2 nanocomposites and their application in supercapacitors

The combination of the attractive properties of graphene with excellent characteristics of other functional nanomaterials has become a popular pathway for achieving applications in multiple fields. Herein, reduced graphene oxide (RGO)/CeO₂ nanocomposites with enhanced capacitive performance were designed and synthesized by a facile two-step approach with a self-assembly method followed by thermal treatment. The structure, morphology and composition of the resulting RGO/CeO₂ nanocomposites were systematically investigated. The presence of RGO can prevent the aggregation and control the structures of the CeO₂ nanocrystals in the annealing process. The nanocomposites as electrode materials for supercapacitor exhibited an enhanced capacitive performance due to the synergic effect between RGO nanosheets and CeO₂ nanocrystals. The excellent capacitive performance of the RGO/CeO₂ nanocomposites offer great promise for supercapacitor applications.     

Potentiostatically deposited polypyrrole/graphene decorated nano-manganese oxide ternary film for supercapacitors

A simple method based on potentiostatic polymerization was developed for the preparation of ternary manganese oxide-based nanocomposite films. The ternary nanocomposites, which were characterized using x-ray diffraction spectroscopy and x-ray photoelectron spectroscopy, showed that the manganese oxide within the film consisted of MnO₂ and Mn₂O₃. Electrochemical measurements showed that the ternary nanocomposite electrode exhibited high specific capacitance (up to 320.6 F/g), which was attributed to the morphology of a polypyrrole/graphene/manganese-oxide (PPy/GR/MnO_x) ternary nanocomposite. The experimental approach maximized the pseudocapacitive contribution from redox-active manganese oxide (MnO_x) and polypyrrole (PPy), as well as the electrochemical double layer capacitive (EDLC) characteristic from graphene (GR) sheets. Long cyclic measurements indicated that the specific capacitance of the ternary nanocomposite film could retain 93% of its initial value over 1000 charge/discharge cycles, in the potential range of −0.2 to 0.7 V versus silver/silver chloride electrode (Ag/AgCl).     

Materials and electrode designs of high-performance NiCo2S4/Reduced graphene oxide for supercapacitors

NiCo₂S₄ is one of the most promising bimetallic sulfides for use in energy-storage systems, but more studies are needed to endow NiCo₂S₄ with a high electrochemical reaction capability and reversibility. In this work, we present rationally materials design of an optimal NiCo₂S₄ nanoparticle in a reduced graphene oxide (RGO) matrix as a NiCo₂S₄/RGO nanocomposite. Furthermore, we report the improvements in the materials technology, demonstrating the NiCo₂S₄/RGO nanocomposite electrode with an excellent specific capacitance of 963–700 F g⁻¹ at 1–15 A g⁻¹, high capacitance retention of 70%, and long cycle life of 3000 cycles. The practical application is showcased in an asymmetric supercapacitor with a high active-material loading. The NiCo₂S₄/RGO nanocomposite shows a high energy density of 31 Wh kg⁻¹ at a power density of 987 W kg⁻¹ and maintains an excellent density of 23 Wh kg⁻¹ at a high power density of 7418 W kg⁻¹. The outstanding electrochemical utilization and stability of the NiCo₂S₄/RGO nanocomposite confirm that our systematic optimization in the materials science and technology in terms of the active-material synthesis, the electrode development, and the device design/fabrication would benefit the future development of high-performance supercapacitors.     

Microwave exfoliated reduced graphene oxide epoxy nanocomposites for high performance applications

Graphene has captured the attention of scientific community due to recently emerging high performance applications. Hence, studying its reinforcing effects on epoxy resin is a significant step. In this study, microwave exfoliated reduced graphene oxide (MERGO) was prepared from natural graphite for subsequent fabrication of epoxy nanocomposites using triethylenetetramine (TETA) as a curing agent via in-situ polymerization. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), C¹³ NMR spectroscopy, X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–vis) spectroscopy were employed to confirm the simultaneous reduction and exfoliation of graphene oxide. The reinforcing effect of MERGO on epoxy resin was explored by investigating its static mechanical properties and dynamic mechanical analysis (DMA) at MERGO loadings of 0 to 0.5 phr. The micro-structure of epoxy/MERGO nanocomposites was investigated using scanning electron microscope (SEM), transmission electron microscope (TEM) and XRD techniques. The present work reports an enhancement of 32%, 103% and 85% in tensile, impact and flexural strength respectively of epoxy by the addition of even 0.25 phr MERGO. At this loading elastic and flexural moduli also increased by 10% and 65%, respectively. Single-edge-notch three-point-Bending (SEN-TPB) fracture toughness (K_IC) measurements were carried out where a 63% increase was observed by the introduction of 0.25 phr MERGO. The interfacial interactions brought about by graphene also benefited the dynamic mechanical properties to a large extent in the form of a significant enhancement in storage modulus and slightly improved glass transition temperature. Considerable improvements were also detected in dielectric properties. The epoxy nanocomposite also attained an ac conductivity of 10⁻⁵ S/m and a remarkable increase in dielectric constant. The simple and cost effective way of graphene synthesis for the fabrication of epoxy/MERGO nanocomposites may be extended to the preparation of other MERGO based polymer nanocomposites. This remarkable class of materials has thrown open enormous opportunities for developing conductive adhesives and in microelectronics.     

One-pot synthesis of Ag-TiO2/reduced graphene oxide nanocomposite for high performance of adsorption and photocatalysis

The Ag-TiO₂/r-GO nanocomposite was synthesized via a facile one-pot solvothermal method. X-ray diffraction (XRD), Transmission electron microscopy (TEM),High resolution transmission electron microscopy(HRTEM), UV–vis diffuse reflectance spectroscopy (DRS), Fourier transformed infrared spectroscopy (FT-IR), Photoluminescence (PL) and N₂ adsorption-desorption were used for the characterization of prepared samples. The adsorbent and photocatalytic performance of prepared samples were evaluated by remove of Rh B dyes and reduction of CO₂. Both the adsorbent and photocatalytic ability of all the Ag-TiO₂/r-GO samples were much higher than pure hollow TiO₂. The excellent adsorbent capacity can be attributed to the large BET surface area and the enhanced photocatalytic activity can be assigned to the predominant properties of graphene and the localized surface plasmon(LSPR) effect of Ag nanoparticles.     

Electrochemical sensing based on graphene oxide/Prussian blue hybrid film modified electrode

A novel graphene oxide (GO)/Prussian blue (PB) hybrid film was constructed by electropolymerizing Prussian blue onto the GO modified glassy carbon electrode, and its electrochemical behaviors were studied. Raman spectra were used to investigate the successful formation of the GO/PB hybrid film. Electrochemical experiments showed that the graphene oxide greatly enhanced electrochemical reactivity of the PB. Moreover, a much higher Prussian blue (PB) loading (6.388 × 10⁻⁸ mol cm⁻²) is obtained as compared to the bare glass carbon surface (3.204 × 10⁻⁹ mol cm⁻²). The GO/PB hybrid film modified electrode was used for the sensitive detection of hydrogen peroxide. The sensor exhibited a wide linearity range from 5.0 × 10⁻⁶ to 1.2 × 10⁻³ M with a detection limit of 1.22 × 10⁻⁷ M (S/N = 3), high sensitivity of 408.7 μA mM⁻¹ cm⁻² and good reproducibility. Furthermore, with glucose oxidase (GOD) as a model, the GO/PB/GOD/chitosan composite-modified electrode was also constructed.The resulting biosensor exhibited good amperometric response to glucose with linear range from 0.1 to 13.5 mM at 0.1 V, good reproducibility and detection limit of 3.43 × 10⁻⁷ M (S/N = 3). In addition, the biosensor presented high selectivity and long-term stability. Therefore, the PB/GO hybrid films-based modified electrode may hold great promise for electrochemical sensing and biosensing applications.     

A new As3Mo8V4/PANi/rGO composite for high performance supercapacitor electrode

Herein, [As₂^IIIAs^VMo₈^VIV₄^IVO₄₀]₂[Cu^ICu₂^II(pz)₄]₂·9H₂O/polyaniline/reduced graphene oxide (pz = pyrazine, abbreviated to As₃Mo₈V₄/PANi/rGO) composite is first assembled, characterized and systematically explored for its supercapacitor performance. As₃Mo₈V₄/PANi/rGO composite shows a exceptional specific capacitance (2351 F g^?1 at 1 A g^?1) and outstanding cyclic stability (96.9% after 5000 cycles). The symmetric supercapacitor exhibits high specific capacitance of 1295 F g^?1 at 1 A g^?1 and excellent energy density of 88.1 Wh kg^-1 at power density of 349.6 W kg^-1, while maintaining a notable capacitance retention of 85.7% after 5000 cycles at 2 A g^-1. The above results confirm the potential application of As₃Mo₈V₄/PANi/rGO composite in energy storage devices.     

Mechanically strong high performance layered polypyrrole nano fibre/graphene film for flexible solid state supercapacitor

Paper like flexible electrode becomes one of the most important research objects recently in request of the fast expanding market of portable electronics. Flexible solid state supercapacitors are shortlisted as one of the most promising energy devices to power electronics with medium to high power density requirements. In this work, we developed a simple but effective way to produce a mechanically strong and electrochemically active RGO/polypyrrole (PPy) fibre paper. A well-bedded microstructure was created with interlaced polypyrrole fibres evenly distributed between the graphene layers. Such microstructure can create enormous amount of pores and therefore provides larger interfaces for charge carrier storage/release. The effects of polypyrrole fibres on the film’s morphologies, mechanical properties and electrochemical performance were discussed. A solid state supercapacitor was demonstrated using such paper electrodes and a gel type electrolyte – phosphate acid (H₃PO₄) infused polyvinyl alcohol (PVA). It showed a high capacitance (345 F g⁻¹) and an excellent cycling stability (9.4% drop after 1000 cycles).     

Enhanced NO2 gas sensor device based on supramolecularly assembled polyaniline/silver oxide/graphene oxide composites

Herein, we report a successful synthesis of supramolecularly assembled polyaniline/silver oxide/graphene oxide composite (PANI/Ag₂O/GO) for enhanced NO₂ gas sensing application. The PANI/Ag₂O/GO composite was synthesized by facile stirring followed by an ultrasonication process. The prepared material was characterized by different techniques such as x-ray diffraction, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy and Raman-scattering spectroscopy. The detailed analysis revealed that the average crystallite sizes of PANI/Ag₂O and PANI/Ag₂O/GO composites were found to be 37.37 nm and 41.55 nm, respectively. FESEM and TEM analysis showed coral-like rough-surfaced and extensively agglomerated morphology for PANI and ultrathin flexible sheet-like morphology for GO. Ag₂O nanoparticles with diameters 20–30 nm were well incorporated in the GO sheets and PANI matrix in the case of PANI/Ag₂O/GO composites. The synthesized materials were used to make resistive sensor devices that had a high response to NO₂ gas. The fabricated sensors were examined at various temperatures to obtain the optimal sensing temperature. The fabricated NO₂ gas sensor device based on PANI/Ag₂O/GO composite exhibited a highest sensitivity of 5.85 for 25 ppm at an optimized temperature (100 °C) as compared to the pure PANI (2.5) and PANI/Ag₂O composite (3.25). Further, the fabricated sensor device based on PANI/Ag₂O/GO composite was also examined at different NO₂ gas concentrations.     

Self-standing manganese dioxide/graphene carbon nanotubes film electrode for symmetric supercapacitor with high energy density and superior long cycling stability

The low capacitance utilization and capacitance fading of manganese dioxide (MnO₂) is mainly due to poor electro-conductivity and irreversible phase transform. This work proposes a new method of designing hierarchical and binder-free electrode based on MnO₂ material for stable supercapacitor with high specific capacitance. Herein, we fabricated the self-standing electrode of MnO₂ on nitrogen-doped graphene and single wall carbon nanotubes (SWCNTs) self-standing film (NGCF) by electrochemical deposition. As a result, as-prepared MnO₂/NGCF cathode showed excellent electrochemical performance of 489.7 F g^-1 at 1 A g^-1. Assembled symmetric aqueous supercapacitor (SC) manifests high voltage of 2.4 V and presents excellent high energy density of 106.7 Wh kg^-1 at 1200 W kg^-1 and outstanding long-life stability without no decay after 10 000 charge-discharge circuits. This work proposes a new view of designing hierarchical and binder-free electrode with high energy density and long cycling stability based on MnO₂ material for stable symmetric supercapacitor.     

Preparation of on chip,flexible supercapacitor with high performance based on electrophoretic deposition of reduced graphene oxide/polypyrrole composites

A new concept is introduced to fabricate flexible, on-chip supercapacitors by electrophoretically depositing highly dispersed reduced graphene oxide/polypyrrole on interdigital-like electrodes. By the unique method, the deposited films could construct on the substrate facilely and uniformly. The prepared all-solid-state device demonstrates high volumetric capacitance (about 147.9 F cm⁻³), high energy density (13.15 mWh cm⁻³ at a power density of 1300 mW cm⁻³) and excellent cycling stability (approximately 71.7% of the initial capacitance retained after 5000 cycles). Compared with other supercapacitor, the device demonstrated here is lightweight, flexible and inexpensive.     

MnO anchored reduced graphene oxide nanocomposite for high energy applications of Li-ion batteries: The insight of charge-discharge process

In the present work, a new class of anode material for high energy applications of Li-ion battery is prepared by easy and large-scale producible process. Herein, the nanocomposite of MnO and reduced graphene oxide (rGO) is prepared by anchoring MnO nanoparticles into 3D matrix of rGO hydrogel followed by annealing process. The composite which has homogeneous distribution of MnO particles on conducting rGO layers demonstrated superior electrochemical performance such as high reversible capacity, stable cycle life and better rate capability. It has shown initial discharge capacity of 2358 mAh g⁻¹ and retained 570 mAh g⁻¹ after 100 cycles as compared to pristine MnO which shown initial discharge capacity of 820 mAh g⁻¹ and retained only 45 mAh g⁻¹ after 100 cycles. The retained capacity of new MnO/rGO anode is much higher than the theoretical capacity of conventional graphite anode. Moreover, the MnO/rGO nanocomposite shows six times higher Li⁺ ion diffusion of 4.18 × 10⁻¹² cm² s⁻¹ as compared to 6.84 × 10⁻¹³ cm² s⁻¹ of MnO. In addition, the study provides insight of charge-discharge process, which conducted in initial, discharge and charge states of pristine MnO and MnO/rGO composite using ex-situ X-ray diffraction and X-ray photon spectroscopy techniques.     

Hydrogen reduced graphene oxide/metal grid hybrid film: towards high performance transparent conductive electrode for flexible electrochromic devices

The metal grid and reduced graphene oxide (RGO) are both promising transparent conductive materials for replacing the indium tin oxide (ITO) in flexible optoelectronics. However, the large empty area that exists in the grid together with the relatively high sheet resistance of RGO hinder both the materials for practical applications. In this work, we report for the first time a novel strategy for efficient combination of the metal grid and RGO by using a newly developed room-temperature reduction technique. The obtained RGO/metal grid hybrid films not only overcome the shortcomings of individual components but exhibit enhanced optical and electrical performances (R_s = 18 Ω sq⁻¹ and T = 80%) and excellent flexural endurance. With this hybrid film as the window electrode, a highly flexible electrochromic device with excellent stability and ultra-fast response shorter than 60 ms has been successfully fabricated. Considering its high efficiency, high quality, low cost and large area, the strategy would be particularly useful for economically fabricating various metal grid/RGO films which are quite promising high performance transparent and conductive materials for next generation optoelectronic devices.     

High performance fiber-shaped flexible asymmetric supercapacitor based on MnO2 nanostructure composited with CuO nanowires and carbon nanotubes

The demand for wearable electronics has greatly promoted the development of flexible supercapacitors. Herein, we develop a series of approaches to fabricate a fiber-shaped supercapacitor with flexibility. In the device, CuO@MnO₂, carbon nanotube (CNT)@MnO₂ and PVA-KOH are respectively used as inner electrode, outer electrode and gel electrolyte. The approaches including in-situ growth of CNTs, in-situ etching removal of SiO₂ template and in-situ filling of gel electrolyte via hydrothermal process are explored to protect the device from structure damage caused by external forces and to maximize effective contact areas between active electrode materials and gel electrolyte. The optimized supercapacitor of copper wire@CuO@MnO₂//PVA-KOH//CNT@MnO₂ demonstrates a good capacitive performance (5.97 F cm^?3) and exhibits a high energy density (0.38 mWh cm^?3) at a power density of 25.5 mW cm^?3. In addition, it has perfect cycling stability (77% after 2000 cycles) with excellent flexibility. Therefore, this work will provide desirable processes to construct fiber-shaped supercapacitors as flexible and wearable energy storage devices.     

Surface immobilisation of transition metal substituted Krebs type polyoxometalates, [X2W20M2O70(H2O)6] (X = Bi or Sb, M = Co or Cu), by the layer by layer technique

A series of transition metal (i.e. Cu²⁺ and Co²⁺) substituted Krebs type polyoxometalates (POMs), of the general formula [X₂W₂₀M₂O₇₀(H₂O)₆]ⁿ⁻, X = Sb or Bi, M = Co(II) or Cu(II), have been successfully immobilised onto carbon electrode surfaces through the employment of the layer-by-layer (LBL) technique. This involved the construction of alternating anionic POM, [X₂W₂₀M₂O₇₀(H₂O)₆]ⁿ⁻, layers and the cationic metallodendrimer, Ru(II)-metallodendrimer as the cationic layers, in addition to a [poly(diallyldimethylammonium chloride)] PDDA base layer. Stable multielectron redox couples associated with the W–O framework, for the Krebs type POMs, and the Ru(III/II) for the metallodendrimer, were clearly observed upon layer construction and redox switching within the pH domain of 2–6.5. The constructed multilayer assemblies exhibited pH dependent redox activity and thin layer behaviour up to 100 mV s⁻¹. The porosity and permeability of the individual multilayer assemblies towards an anionic probe were determined by AC impedance and cyclic voltammetry. The surface morphology of each multilayer was also determined by Atomic Force Microscopy (AFM).