Synthesis of black pigments containing chromium from leather sludge

The black ceramic pigments with spinel structure have been prepared by using Cr-rich leather sludge in this paper. The washed Cr-rich leather sludge calcined at 1100 °C for 1 h as chromium oxide precursor (named as CA) was mixed with an appropriate proportion of other industrial metallic oxides, followed synthesizing black ceramic pigment by sintering. Both non-washed and washed sludge fired at 1100 °C were characterized by X-ray fluorescence (XRF) in order to determine their chemical compositions and X-ray diffraction (XRD) analysis to confirm that CA mainly contains Cr₂O₃ crystal phase. The results show that CA could be used as a source of chromium to prepare black pigment. The crystalline phases of obtained pigments were characterized by XRD. Furthermore, the morphology as well as the composition of pigments was investigated by scanning electron microscopy (SEM) and energy dispersion spectroscopy (EDS). The color coordinates of pigments were examined and compared with the commercial pigments based on CIE-L* a* b* values measured using UV–vis spectroscopy. The obtained pigments sintered at 1200 °C with 35–55 wt% content of CA possess the excellent black spinel structure and color effect. Under optimized conditions, the pigment has low average spectral reflectance (7%).     

Solution combustion of spinel CuMn2O4 ceramic pigments for thickness sensitive spectrally selective (TSSS) paint coatings

A series of spinel-type CuMn₂O₄ ceramic pigments were prepared by a facile and low-cost sol-gel solution combustion method and used as cost-effective materials to fabricate thickness sensitive spectrally selective (TSSS) paint coatings by a convenient spray-coating technique. The chemical component, crystalline morphology, and optical property of the copper manganese oxide ceramic pigment could be accurately controlled by altering the annealing temperature. X-ray diffraction (XRD) analysis confirmed that the ceramic pigments annealed at 500 °C for 1 h coincided well with the XRD patterns of crystalline CuMn₂O₄ in the JCPDS database, and there were segregated phases of CuO and Mn₂O₃. Furthermore, the pure spinel CuMn₂O₄ phase could be achieved at 900 °C for 1 h. The copper manganese oxide ceramic pigments could serve as an effective pigment for fabricating the TSSS paint coating, and the TSSS paint coatings based on ceramic pigments calcined at 900 °C showed solar absorptance of 0.895–0.905 and thermal emittance of 0.186–0.310. In addition, the accelerated thermal stability test revealed that the TSSS paint coating exhibited good thermal stability when it was exposed to air at a temperature of 300 °C for 300 h. Hence, the fabricated TSSS paint coating could be used as a solar absorber coating in the low-to-mid temperature domain.     

Effect of boron oxide on the microstructure of mullite-based glass-ceramic glazes for floor-tiles in the CaO–MgO–Al2O3–SiO2 system

The effect of increasing replacement of Al₂O₃ by B₂O₃ in a parent glass on the sintering and further crystallization of mullite was investigated. The composition of the parent glass was chosen in the mullite primary phase field of the CaO–MgO–Al₂O₃–SiO₂ quaternary system. Glass powder pellets were heated under standard (10 °C/min and 2 h of hold time) and fast heatings (25 °C/min and 5 min of hold time) at different temperatures from 700 to 1190 °C. Sintering of B₂O₃-containing glasses took place in the range between 850 and 1050 °C. X-ray diffraction results showed that mullite formed as unique crystalline phase for glasses containing amounts of B₂O₃ larger than 6 wt%. For lower amounts of boron oxide cordierite was formed as secondary crystalline phase. Quantitative determination of mullite by Rietveld analysis indicated that the higher amount of mullite present in the glass-ceramic fast heated at 1160 °C was 19.5 wt% for the glass containing 9 wt% of B₂O₃. The final microstructure of the glass-ceramic glazes showed the presence of well shaped, long acicular mullite crystals dispersed within the residual glassy phase. Results of glass-ceramic glazes when applied as slurry and under industrial heating conditions pointed out promising mechanical properties.     

Glass-ceramic glazes for future generation floor tiles

Glaze in the CaO–MgO–Al₂O₃–SiO₂ system was heated at 950–1190 °C for 2 h and characterized. X-ray diffraction showed that only trace amount of mullite was formed in the glass-ceramic glaze heated at 950 °C. Both mullite and α-cordierite were formed in the glass-ceramic glaze heated at 1050 °C as primary and secondary phases. Glass-ceramic glazes heated at 1120 °C and 1190 °C contained α-cordierite and mullite as major and minor phases. Rietveld analysis revealed that the amount of α-cordierite increased and mullite decreased with increasing heating temperature. Field emission scanning electron microscopy showed presence of mullite crystals dispersed within residual glassy phase in the glass-ceramic glazes heated at 950 °C and 1050 °C. In the microstructures of glass-ceramic glazes heated at 1120 °C and 1190 °C α-cordierite crystals were mainly appeared. Energy Dispersive X-ray analysis corroborated X-ray diffraction results. Vickers microhardness measurement demonstrated highest hardness (8.38 ± 0.07 GPa) of the glass-ceramic glaze heated at 1190 °C.     

Environmental-friendly yellow pigment based on Tb and M (M = Ca or Ba) co-doped Y2O3

A yellow inorganic ceramic pigment with general formula Y_1.86?xM_xTb_0.14O_3?x/2 (M = Ca and/or Zn) with x = 0.06, 0.32 and 0.64 were synthesized by a modified Pechini method. XRD, SEM and HRTEM/EDX analysis showed the formation of solid solution at 1300 °C when x = 0.06 and 0.32. The best b* yellow coordinates were obtained for Ca and Zn co-doped Y_1.86Tb_0.14O₃ samples. The intensity of the yellow colour in the samples is related to the presence of Tb⁴⁺ ions. Samples with higher concentration of Tb⁴⁺ ions lead to a better yellow colour. The chemical stability of these pigments was determinate in an industrial glaze. The glazing tests indicated that the powder samples with x = 0.06 and 0.32 fired at 1300 °C were stable in the glaze. These results make it a potential candidate for environmental friendly yellow ceramic pigment to be used in applications such as pigment for glazes or inkjet printers.     

Characteristics of samaria-doped ceria nanoparticles prepared by spray pyrolysis

Samaria-doped ceria (SDC) nanoparticles were prepared by spray pyrolysis. The means sizes of the samaria-doped ceria nanoparticles were controlled from 21 to 150 nm by changing the calcination temperatures between 700 and 1200 °C. The pellets formed from the SDC particles calcined at temperatures between 700 and 1000 °C had similar grain sizes between 0.75 and 0.82 μm. However, pellet formed from the SDC particles calcined at a temperature of 1200 °C had large grain size of 1.22 μm. The pellet formed from the SDC particles calcined at a temperature of 1000 °C had slightly smaller resistance of grain-boundary than those of the pellets formed from the SDC particles calcined at temperatures between 700 and 900 °C. However, the pellet formed from the SDC particles calcined at a temperature of 1200 °C had low resistance of grain-boundary. The pellet formed from the SDC particles calcined at a temperature of 1200 °C had conductivity of 44.65 × 10^?3 S cm^?1 at a measuring temperature of 700 °C that more twice than those of the pellets formed from the SDC calcined below 1000 °C.     

Co-doped willemite ceramic pigments: Technological behaviour,crystal structure and optical properties

Cobalt-doped willemite is a promising blue ceramic pigment, but some important aspects concerning crystal structure, optical properties and technological behaviour are still undisclosed. In order to get new insight on these features, willemite pigments (Zn_2?xCo_xSiO₄, 0 < x < 0.3) were synthesized by the ceramic route and characterized from the structural (XRPD with Rietveld refinement), optical (DRS and colorimetry), microstructural (SEM, STEM, TEM, EDX, EELS) and technological (simulation of the ceramic process) viewpoints. The incorporation of cobalt in the willemite lattice, taking preferentially place in the Zn1 tetrahedral site, induces an increase of unit-cell parameters, metal–oxygen distances, and inter-tetrahedral tilting. It causes shifting and enhanced splitting of spin-allowed bands of Co²⁺ in tetrahedral coordination, implying slight changes of crystal field strength Dq and Racah B parameter, but increasing spin-orbit coupling parameter λ. Willemite pigments impart deep blue hue to ceramic glazes and glassy coatings with a colouring performance better than commercial Co-bearing colorants in the 800–1200 °C range. Detailed SEM-TEM investigation and microanalysis proved that no diffusion phenomena occur at the pigment–glassy coating interface and that willemite pigments are chemically inert during firing at 1050 °C.     

Porous zirconium titanate ceramics synthesized by sol–gel process

Zirconium titanate, ZrTiO₄, was synthesized by sol–gel method from zirconium butoxide and titanium isopropoxide. Amorphous ZrTiO₄ powder was ground, calcined at 500 °C, and milled to homogenize size distribution of the powder. Milled powder was pressed into tablets and sintered at 900–1400 °C for 8 h. Differential scanning calorimetry and dilatometric studies indicated crystallization of ZrTiO₄ at 600–700 °C. Raman spectroscopy and X-ray diffraction analysis confirmed presence of crystallized ZrTiO₄ already at 900 °C, and crystallite size was determined by Scherrer equation. Scanning electron microscopy showed that ZrTiO₄ grains begin to sinter at higher temperatures, starting from 1200 °C, while preserving high porosity up to 1300 °C as confirmed by dilatometry and mercury intrusion porosimetry.     

Synthesis and characterization of red pigment YAl1−yCryO3 prepared by the low temperature combustion method

In the present study, a red-shade pigment, based on the system YAl_1?yCr_yO₃ (y = 0–0.05), was synthesized for the first time using the low temperature combustion method. The single-phase synthesis of YAl_1?yCr_yO₃ was achieved at a temperature of 1000 °C. The resulting calcined powders were micron-sized particles (0.5–3 μm) with a well-developed cubic perovskite structure. The study specifically investigated the chemical composition, calcination temperature, Cr³⁺ content, and the effect of the mineralizer in order to elucidate the optimal conditions for pigment synthesis. Further, the color properties exhibited by the YAl_1?yCr_yO₃ pigment when it was added into basic glazes have also been obtained. In addition, the products were characterized by DTA, XRD, FESEM, EDX, and color spectrometry.     

New glass-based coatings coloured with red pigments for Foamglas® panels

This work describes the design and development of new coloured glass-based coatings for Foamglas^® substrates. Four kinds of pigments were added in different proportions (1 and 5 wt% respectively) to a borate glassy matrix (labelled as G7) by two different mixing techniques; the chosen pigments were goethite (α-FeOOH), acicular hematite (Fe₂O₃) spherical hematite and TiO₂ coated hematite. No interaction occurred between the selected pigments and the G7 matrix and consequently no new phases were formed in the reported experimental conditions. Coatings on the Foamglas^® substrates were sintered at 560 °C for 1 h and showed different porosity, pigment dispersion in the matrix and colour development, depending on the mixing technique.The porosity was exploited to add TiO₂ coated hematite into the coating, for photo-catalytic purposes. Each coating was deposited without affecting the Foamglas^® substrate porous structure.     

Effects of Li2CO3 addition on the microstructure and magnetic properties of low-temperature-fired NiCuZn ferrites

NiCuZn ferrites doped with 0.5 wt% Bi₂O₃ and different Li₂CO₃ contents (0–0.25 wt%) were sintered at 900 °C. The microstructure and magnetic properties of these materials were investigated. The addition of low-melting-point Li₂CO₃ led to large and uniform grains. However, excess Li₂CO₃ addition produced abnormal grains and many closed pores, thereby reducing density. Permeability initially increased and then decreased at the Li₂CO₃ content of >0.2 wt%. Maximum magnetic flux density (431.1 mT at room temperature, 339.6 mT at 100 °C) and minimum power loss were achieved at 0.2 wt% Li₂CO₃. These findings suggested the suitability of 0.2 wt% Li₂CO₃ for applications in low-temperature co-fired ceramic magnetic power components and modules.     

Synthesis and characterization of LTCC compositions with middle permittivity based on CaO-B2O3-SiO2 glass/CaTiO3 system

CaTiO₃ ceramics with the addition of CaO-B₂O₃-SiO₂ (CBS) glass (45–55 wt%) composites were sintered at 830 °C, 850 °C, 875 °C and 900 °C. To illustrate influence mechanism of the different glass contents and sintering temperatures on the properties of the composites, we focused on the multiple performances of the composites by employing different qualitative and quantitative instruments. Composites with 50 wt% glass sintered at 875 °C presented fairly ideal performance: the bulk density was 3.20 g/cm³, the dielectric constant was 25.7 and the dielectric loss was 0.0009 at 7 GHz. Micro-Structure analysis of the composites showed a dense and pore-less microstructure except for few pores with size around 1 μm. In addition, the composite could meet the shrinkage requirement of Ag electrodes and could not possibly react with Ag electrodes any more. This makes them suitable for various dielectric applications at low sintering temperature.     

Effect of spinel content on hot strength of alumina-spinel castables in the temperature range 1000–1500°C

Hot modulus of rupture of Al₂O₃-spinel castables containing 5–15 wt% alumina-rich magnesia alumina spinel and 1·7 wt% CaO generally increases with increase in spinel content and temperature from 1000 to 1500°C. The magnitudes of hot modulus of rupture of castables containing 15 wt% spinel and 1·7 wt% CaO are 14·3 MPa at 1400°C and 15·6 MPa at 1500°C, while those of castables containing 20 wt% spinel and 1·7 wt% CaO are 12·5 MPa at 1400°C and 14·7 MPa at 1500°C. The former castables contained 15 wt% spinel of −75 μm size, while the latter contained 10 wt% spinel of +75 μm size and another 10 wt% spinel of −75 μm size. The bond linkage between the CA₆ and spinel grains in the matrix is believed to cause both the spinel content and temperature dependence of hot strength of Al₂O₃-spinel castables, as well as fine grain spinel even in amount less than coarser grain spinel to be more effective for enhancing hot strength. The trend of the magnitude of thermal expansion under load (0·2 MPa) above 1500°C of the castables is not necessarily indicative of the magnitude of hot modulus of rupture at 1400 or 1500°C. ©     

Low-dielectric-constant LiAlO2 ceramics combined with LBSCA glass for LTCC applications

This study used Li₂O–B₂O₃–SiO₂–CaO–Al₂O₃ (LBSCA) glass to reduce the sintering temperature of LiAlO₂ ceramics and to realise the low dielectric constants (ɛ_r<5) of low-temperature co-fired ceramic (LTCC) materials. LBSCA glass remarkably enhanced the densification of LiAlO₂ ceramics. X-ray diffraction patterns indicated that only the γ-LiAlO₂ phase occurred within the doping range of 1 wt% to 3.5 wt%. Scanning electron microscopy images showed dense and uniform grains in samples with 3.0 wt% LBSCA glass. These samples also exhibited low dielectric constants and low dielectric loss when sintered at 900 °C and 950 °C (i.e., ɛ_r=4.48, Qf=35,540 GHz and τ_f=−53 ppm/°C at 900 °C; ɛ_r=4.50, Qf=38,979 GHz and τ_f=−55 ppm/°C at 950 °C, respectively). The material prepared was chemically compatible with silver and showed potential in applications of high-frequency LTCC microwave substrates.     

Transparent mullite ceramic from single-phase gel by Spark Plasma Sintering

Monophasic mullite precursors with composition of 3Al₂O₃·2SiO₂ (3:2) were synthesized and then were sintered by Spark Plasma Sintering (SPS) to form transparent mullite ceramics. The precursor powders were calcined at 1100 °C for 2 h. The sintering was carried out by heating the sample to 1450 °C, holding for 10 min. The sintered body obtained a relative bulk density of above 97.5% and an infrared transmittance of 75–82% in wavelength of 2.5–4.3 μm without any additive. When the precursor powders were calcined at below 1100 °C, it was unfavorable for completely eliminating the residual OH, H₂O and organic compound. However, when calcined temperature was too high, it was unfavorable either for full densification due to the absence of viscous flow of amorphous phase. At the same calcined temperature, the transmittance of sintered body was decreased with the increase of the sintering temperature above 1450 °C owing to the elongated grain growth.     

Preparation of porous Al2TiO5-Mullite ceramic by starch consolidation casting and its corrosion resistance characterization

Stabilized Al₂TiO₅ (AT)-mullite (M) porous ceramics were fabricated by starch consolidation casting using corn starch as curing agent and their microstructure, mechanical properties, pore size distribution and corrosion resistance were examined. Results showed that AT-M porous ceramic with the flexural strength of 11.5 MPa, apparent porosity of about 54.7% and pore size distribution in the range of 1–15 µm could be obtained with 10 wt% corn starch addition. Corrosion resistance results showed mass losses in hot H₂SO₄ solution and NaOH solution for 10 h to decreased from 1.03% to 0.36% and 4.39–2% when the calcination temperature increased from 1400 °C to 1450 °C, which proved these AT-M porous ceramics to possess an excellent corrosion resistance in acidic condition when calcined at 1450 °C.     

Formation of hollow MgO-rich spinel whiskers in low carbon MgO–C refractories with Al additives

MgO–C refractories with different carbon contents have been developed to meet the requirement of steel-making technologies. Actually, the carbon content in the refractories will affect their microstructure. In the present work, the phase compositions and microstructure of low carbon MgO–C refractories (1 wt% graphite) were investigated in comparison with those of 10 wt% and 20 wt% graphite, respectively. The results showed that Al₄C₃ whiskers and MgAl₂O₄ particles formed for all the specimens fired at 1000 °C. With the temperature up to 1400 °C, more MgAl₂O₄ particles were detected in the matrix and AlN whiskers occurred locally for high carbon MgO–C specimens (10 wt% and 20 wt% graphite). However, the hollow MgO-rich spinel whiskers began to form locally at 1200 °C and grew dramatically at 1400 °C in low carbon MgO–C refractories, whose growth mechanism was dominated by the capillary transportation from liquid Al at these temperatures.     

Effect of calcination temperature on the fabrication of transparent lutetium titanate by spark plasma sintering

Transparent lutetium titanate (Lu₂Ti₂O₇) bodies were fabricated by spark plasma sintering using Lu₂O₃ and TiO₂ powders calcined from 700 °C to 1200 °C. No solid-state reaction was identified after calcination at 700 °C, whereas single-phase Lu₂Ti₂O₇ powder was prepared at 1100 and 1200 °C. The calcination at 700 °C promoted densification at the early stages of sintering, whereas residual pores at grain boundaries resulted in Lu₂Ti₂O₇ bodies with low transparency. Low-density and opaque Lu₂Ti₂O₇ bodies formed owing to the coarsening of the powder calcined at 1200 °C. The Lu₂Ti₂O₇ body sintered using the powder calcined at the moderate temperature of 1100 °C had a density of 99.5% with the highest transmittances of 41% and 74% at wavelengths of 550 nm and 2000 nm, respectively.     

Dielectric properties of nano-sized Ba0.7Sr0.3TiO3 powders prepared by spray pyrolysis

Nano-sized Ba_0.7Sr_0.3TiO₃ powders are prepared by post-treatment of the precursor powders with hollow and thin wall structure at temperatures between 900 and 1100 °C. Ethylenediaminetetraacetic acid and citric acid improve the hollowness of the precursor powders prepared by spray pyrolysis. The mean sizes of the powders post-treated at temperatures of 900, 1000 and 1100 °C are 42, 51 and 66 nm, respectively. The densities of the Ba_0.7Sr_0.3TiO₃ pellets obtained from the powders post-treated at 900, 1000 and 1100 °C are each 5.36, 5.55 and 5.38 g cm^?3 at a sintering temperature of 1300 °C. The pellet obtained from the powders post-treated at 1000 °C has higher maximum dielectric constant than those obtained from the powders post-treated at 900 and 1100 °C.     

NaCl–H2O-assisted preparation of SrTiO3 nanoparticles by solid state reaction at low temperature

An environmentally friendly NaCl–H₂O system was developed to synthesize monodisperse strontium titanate (SrTiO₃) nanoparticles from commercially available raw materials (SrCO₃ and rutile) by solid state reactions. The formation rate of SrTiO₃ was accelerated by the addition of NaCl and water vapor. Single phase SrTiO₃ was obtained by calcination at 700 °C for 2 h in water vapor (H₂O flow rate of 2.0 mL/min) by the addition of 50 wt% NaCl, although 900 °C and 750 °C for 2 h were required to complete the reaction by calcinations in air and air by the addition of 50 wt% NaCl, respectively. The results demonstrate that both NaCl and H₂O played vital roles to accelerate the formation of SrTiO₃ nanoparticles at relatively low temperature. On the basis of experiments and analysis, a rational growth mechanism has been proposed and discussed.