An evaluation of plasma-sprayed coatings based on Al2O3 and Al2O3–13 wt.% TiO2 with bond coat on pure titanium substrate

In this study, the effects of bond coat on the properties of Al₂O₃ and Al₂O₃–13 wt.% TiO₂ coatings, which is plasma sprayed onto a commercial pure titanium substrate with and without Ni–5 wt.% Al (METCO 450 NS) as bond coating layer were investigated in terms of microhardness, bonding strength and surface roughness. Optical and scanning electron microscopy (SEM) examinations revealed that there is a uniform coating layer with no spalling and delamination. However, there is a little amount of porosity. The results indicated that the application of bond coat layer in the plasma spraying of Al₂O₃ and Al₂O₃–13 wt.% TiO₂ on pure titanium substrate has increased the hardness and bonding strength of coatings. While the adhesive bonding is dominant without bond coat, the cohesive bonding is dominant with the application of the bond coating layer. It has been observed that percentage of cohesion strength was about three times higher than that of adhesion strength.     

Friction and wear property of a-CNx coatings sliding against ceramic and steel balls in water

The amorphous carbon nitride coatings (a-CN_x) were deposited on Si₃N₄ disks using ion beam assisted deposition (IBAD), and their composition and chemical bonding were determined by X-ray photoelectron spectroscopy (XPS). The a-CN_x coatings' hardness was measured by nano-indentation and the friction and wear property of the a-CN_x coatings sliding against Si₃N₄, SiC, Al₂O_3, SUS440C and SUJ2 balls in water were investigated by using ball-on-disk tribo-meter. The worn surfaces were observed using optical microscopy and analyzed by XPS. The results of XPS analysis showed that the a-CN_x coatings contained 12 at.% nitrogen and the major chemical bonding was sp² C = N and sp³C–N. The nano-hardness of the a-CN_x coatings was 29 GPa, higher than those of balls. Among five kinds of tribo-systems, the lowest friction coefficient was obtained in the range of 0.01 to 0.02 for the tribo-systems with SiC and Si₃N₄ balls, the largest wear rate of the a-CN_x coating of 1.77 × 10^− 7 mm³/Nm was obtained as sliding against Al₂O₃ ball, while the smallest wear rate of a-CN_x coating of 1.44 × 10^− 8 mm³/Nm was gotten as sliding against Si₃N₄ ball. However, SUJ2 ball showed the highest wear rate of 7.0 × 10^− 7 mm³/Nm, whereas Al₂O₃ ball exhibited the lowest wear rate of ball of 3.55 × 10^− 9 mm³/Nm. The XPS analysis on the worn surface for the a-CN_x coatings displayed that the nitrogen concentration decreased and the sp²-bonding-rich structure was formed after sliding tests in water.     

Al2O3/Si3N4 nanocomposite coating on aluminum alloy by the anodizing route: Fabrication,characterization, mechanical properties and electrochemical behavior

An Al₂O₃/Si₃N₄ nanocomposite coating was successfully fabricated on commercial aluminum alloy. Hardness measurements, polarization and electrochemical impedance spectroscopy (EIS) were employed to study the mechanical and corrosion behaviors of the coatings. Field-Emission Scanning Electron Microscopy (FE-SEM) equipped with Energy Dispersive Spectroscopy (EDS) and X-ray diffraction (XRD) were utilized to characterize the surface morphology and phase composition of the coatings. Also, coatings abrasive wear properties were evaluated with a modified ASTM G105 standard. FE-SEM image, EDS and XRD analysis revealed the presence of Si₃N₄ in the coating. Furthermore, the results showed hardness of the coatings to increase from 380±50 HV for the anodized layer to 712±36 HV for the composite coatings that were formed in an electrolyte containing 6 gr/lit Si₃N₄ nanoparticles. Electrochemical measurements indicated that corrosion resistance of the nanocomposite coating significantly increased compared to the anodized coating. In addition, the effect of Si₃N₄ nanoparticles into the nanocomposite coatings on abrasive wear mechanism and mass loss rate of the coatings was investigated.     

Comparative study of the corrosion resistance of thermally sprayed ceramic coatings and their bulk ceramic counterparts

A comparative study of the corrosion properties of thermally sprayed ceramic coatings (Al₂O₃, Al₂O₃–TiO₂ with different ratios, mullite, and ZrSiO₄) and their sintered bulk ceramic counterparts was performed. The coatings were deposited on corrosion-resistant steel substrates using atmospheric plasma spraying (APS) and high velocity oxy-fuel (HVOF) spraying processes. The corrosion properties were investigated in 1 N solutions of NaOH and H₂SO₄ at 85 °C, respectively. The coating microstructures and phase compositions, as well as the corrosive environment were shown to have a strong effect on the corrosion resistance of the coatings. Al₂O₃–coatings were more sensitive to these factors than Al₂O₃–TiO₂ coatings were.The corrosion resistance of the bulk ceramics was superior to that of the thermally sprayed coatings. This is mainly because the coatings exhibited specific microstructure and contained amorphous and/or metastable phases not appearing in the bulk ceramics.     

Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method

Mechanical resistance of Al₂O₃ + TiO₂ nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO₂ nanoparticles dispersed in 3 wt% solution of Al₂(NO₃)₃, as Al₂O₃ precursor, in ethanol. TiO₂ nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition, coatings were annealed at various temperatures, 300, 1000 and 1200 °C, and next exposed to cyclic thermal and slurry tests. Regardless of annealing temperature and the size of TiO₂ nanoparticles, the outer layer of all coatings was porous. The first five thermal cycles caused a rapid increase of aluminum content of the surface layer to 30–37 wt%, but further increase in the number of thermal cycles did not affect the aluminum content. The oxidation rate of coating-substrate system was lower during the thermal tests than during annealing. The oxidation rate was also lower for smaller TiO₂ particles (15 nm) forming the coating than for the larger ones (32 nm). The protective properties of Al₂O₃ + TiO₂ coating against intense oxidation of substrate were lost at 1200 °C. Slurry tests showed that coatings annealed at 1000 °C had the best slurry resistance, but thermal tests had weakened this slurry resistance, mainly due to decreasing adhesion of the coating.     

Alternant phase distribution and wear mechanical properties of an Al2O3-40 wt%TiO2 composite coating

Al₂O₃-40 wt%TiO₂ (AT40) coating is a low-cost and widely applied ceramic coating. In this article, the phase distribution, micro-hardness and wear mechanism, as well as the spraying conditions optimization, are discussed. Interface defects. Phase distribution and phase composition were analysed using SEM and XRD. The results show that the pre-existing surface morphology mainly determines the phase distribution. Al₂TiO₅ and γ-Al₂O₃ are the main phases in the coating. In this experiment, the highest micro-hardness (1126.2 HV_0.2) was measured using a Vickers tester. Additionally, the wear rate of the highest micro-hardness coating is 0.0387 mg/N m, which is the lowest weight loss rate measured among all the samples. The wear mechanism for this sample is primarily scratches. In conclusion, the compact lamellar phase distribution decreases the number of interface defects, increases the hardness and determines the wear mechanism. Also, the phase distribution is affected by the spraying conditions.     

Wear resistance of alumina-coated oil casing steel N80 via MAO with rare earth additive

The wear resistance of oil casing steel N80 was improved by packing its aluminide prelayer at a relative low temperature. Then, an alumina coating was obtained through microarc oxidation (MAO), in which different La₂O₃ contents were added into the electrolyte. The chemical compositions and microstructures of the as-prepared coatings were characterized through scanning electron microscopy (SEM) equipped with energy-dispersive spectrometer (EDS). The wear resistance of the coated oil casing steel N80 under simulated oil and gas well condition was also investigated. With 1.5 g/L La₂O₃ addition, a denser alumina coating containing α-Al₂O₃ and γ-Al₂O₃ with 1750 HV microhardness value was obtained. Under the simulated oil and gas well wear condition, the oil casing steel N80 with an alumina ceramic coating, which was prepared by adding 1.5 g/L La₂O₃ in the electrolyte, showed a stable friction coefficient and low weight loss. Among the steel samples in this study, the oil casing steel N80 with an alumina ceramic coating exhibited the least wear debris and the shallowest groove. The influence mechanism of rare earth on the microstructure of the ceramic coating via MAO was discussed in detail.     

Oxidation behavior of Al2O3 reinforced MoSi2 composite coatings fabricated by vacuum plasma spraying

MoSi₂, MoSi₂–10 vol.% Al₂O₃, MoSi₂–30 vol.% Al₂O₃ (denoted as MA0, MA1, MA3, respectively) coatings were fabricated by vacuum plasma spraying (VPS), and their oxidation behavior was examined at low temperature (500 °C) and high temperature (1500 °C). The test at 500 °C showed that the addition of Al₂O₃ effectively restrained the pest oxidation of MoSi₂. The MA1 coating had satisfactory fluid surface and presented good oxidation resistance at 1500 °C. However, the MA3 coating showed worse oxidation resistant behavior compared with the MA0 coating because of mullite formation.     

Structure and surface properties of Al2O3–TiO2 ceramic coated AZ31 magnesium alloy

Magnesium and its alloys are the engineering materials which have the potential ability to be able to used widely particularly in the automotive, aerospace and in the biomedical sectors, especially thanks to their features such as lightness, specific strength that they have and biocompatibility. However, due to their poor wear resistance and corrosion resistance, the areas of usage are being restricted. This situation prevents Mg alloys to be used without any surface protection despite their good mechanical properties such as high strength/weight ratio. In this study, plasma spraying method is used to improve the poor corrosion resistance of AZ31 Mg alloy. Al₂O₃–13 wt% TiO₂ (AT13) and Al₂O₃–40 wt% TiO₂ (AT40) composite ceramic coatings were coated successfully on the surfaces of AZ31 Mg samples. The wear properties of the AT13 and AT40 coated samples were investigated for tribological applications. Surface morphology and microstructure of the duplex treated samples were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The microhardness value of the uncoated AZ31 Mg alloy is 40±3 HV_0.1, while the microhardness values of the AT40 and AT13 coatings are enhanced to 800±39 HV_0.1 and 1500±35 HV_0.1, respectively.     

Constrained sintering of YSZ/Al2O3 composite coatings on metal substrates produced from eletrophoretic deposition

Yttria stabilized zirconia/alumina (YSZ/Al₂O₃) composite coatings were prepared from electrophoretic deposition (EPD), followed by sintering. The constrained sintering of the coatings on metal substrates was characterized with microstructure examination using electron microscopy, mechanical properties examination using nanoindentation, and residual stress measurement using Cr³⁺ fluorescence spectroscopy. The microstructure close to the coating/substrate interface is more porous than that near the surface of the EPD coatings due to the deposition process and the constrained sintering of the coatings. The sintering of the YSZ/Al₂O₃ composite coating took up to 200 h at 1250 °C to achieve the highest density due to the constraint of the substrate. When the coating was sintered at 1000 °C after sintering at 1250 °C for less than 100 h, the compressive stress was generated due to thermal mismatch between the coating and metal substrate, leading to further densification at 1000 °C because of the ‘hot pressing’ effect. The relative densities estimated based on the residual stress measurements are close to the densities measured by the Archimedes method, which excludes an open porosity effect. The densities estimated from the hardness and the modulus measurements are lower than those from the residual stress measurement and the Archimedes method, because it takes account of the open porosity.     

Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel

Commercially available austenic stainless steel substrate was coated with commercially available, raw Al₂O₃ powder applied by means of plasma spraying method and then re-melted with CO₂ laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser beam of various parameters on the microstructure, phase constituents, and mechanical and tribological properties of the ceramic coating was investigated by means of scanning electron microscopy, light microscopy, computer tomography, X-ray diffraction technique and nanoindentation tests. The micro sliding wear performance of the coatings was tested using a nanoindenter. The study showed an improvement of the mechanical and tribological properties caused by the laser treatment. The best results were achieved for coating re-melted with 120 J/mm laser beam.     

Frictional behavior and wear resistance performance of gradient cermet composite tool materials sliding against hard materials

Gradient cermet composites possessing high surface hardness, flexural strength and interface bonding strength were fabricated using vacuum hot-pressing sintering. Ball-on-disk tests were performed to investigate the tribological properties of the gradient cermet composites against 440 C stainless steel, Al₂O₃ and Si₃N₄ balls at different sliding speed and load in comparison with traditional Ti(C,N) cermets. The tribological behavior was characterized in terms of friction coefficient and wear rate. The results showed that friction coefficient was significantly dependent on the sliding speed and load when sliding against Al₂O₃ and Si₃N₄. However, there was no obvious relation between them during sliding against 440 C stainless steel due to the formation of metal adhesive layer. Gradient cermet composites exhibited a higher friction coefficient but lower wear rate than traditional Ti(C,N) cermets. The main wear mechanism of gradient cermet composites was adhesion wear during sliding against 440 C stainless steel, while abrasion wear was the predominant mechanism during sliding against Al₂O₃ and Si₃N₄. It was expected that gradient cermet composites would be excellent candidates for cutting tool materials.     

Thermal stability and oxidation resistance of V-alloyed TiAlN coatings

V-containing nitride coatings recently attract a wide range of research interests owing to their excellent tribological properties. To evaluate their comprehensive properties, a comparative study on the intrinsic thermal stability and oxidation resistance of TiAlN and TiAlVN coatings are conducted here. Ti_0.56Al_0.44N, Ti_0.50Al_0.44V_0.06N, and Ti_0.40Al_0.50V_0.10N coatings, deposited by cathodic arc evaporation, exhibit a single-phase face-centered cubic structure with a hardness of 28.9–29.8 GPa. The V-containing coatings show a pronounced age-hardening upon annealing, which contributes to a hardness increase of 3.7 and 4.8 GPa at 800 °C for Ti_0.50Al_0.44V_0.06N and Ti_0.40Al_0.50V_0.10N, respectively, corresponding to 2.9 GPa for Ti_0.56Al_0.44N. Also, alloying with V retards the formation of wurtzite AlN upon annealing, especially in Ti_0.50Al_0.44V_0.06N, and thus contributes to a higher hardness above 30 GPa even annealing at 1100 °C, while the hardness of Ti_0.56Al_0.44N significantly reduces to 27.8 ± 0.6 GPa. However, alloying with V into TiAlN leads to an earlier formation of rutile TiO₂ and also Ti-rich oxide top-layer on the outside surface instead of dense Al₂O₃, and thus degrades the oxidation resistance. When exposed to air at 700 °C for 10 h, the Ti_0.50Al_0.44V_0.06N and Ti_0.40Al_0.50V_0.10N coatings suffer from a severe oxidation, whereas only a compact oxide scale with a thickness of ~ 80 nm for Ti_0.56Al_0.44N is formed.     

Thermal stability of nanostructured 13 wt% Al2O3–8 wt% Y2O3–ZrO2 thermal barrier coatings

Nanostructured 13 wt% Al₂O₃–8 wt% Y₂O₃–ZrO₂ (13AlYSZ) coatings were developed by atmospheric plasma spraying (APS). The phase structure and the morphology of the 13AlYSZ coatings were characterized using X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). It was found that the as-sprayed coatings mainly consisted of tetragonal zirconia, with the Al element solid solution in ZrO₂. Heat treatment at 1100 °C increased the average grain size of the ZrO₂ phase from 61 to 120 nm and decreased the porosity from 23.8 to 18%. The addition of the nano-Al₂O₃ can effectively inhibit the grain growth of the zirconia phase. The mechanism on inhibiting the grain growth of nanostructured 8 wt% Y₂O₃–ZrO₂ thermal barrier coatings has been discussed in detail.     

Structure characterisation and mechanical properties of crystalline alumina coatings on stainless steel fabricated via sol–gel technology and fibre laser processing

The surface modification of stainless steel by coating with alumina (Al₂O₃) was carried out using sol–gel coating technology in combination with laser processing. Alumina coatings have been synthesised via a sol–gel route and deposited on stainless steel substrates by dip coating. The coated substrates were then treated with pulsed ytterbium fibre laser radiation (λ = 1064 nm) in continuous wave mode with different specific energies. The composition and structure of the coated surfaces after laser processing were characterised by ATR-FTIR, XRD, SEM and contact angle measurements, whilst the mechanical properties of modified surfaces were determined using nano-indentation. The results showed that the alumina xerogel films coated on the substrates are successfully converted into crystalline alumina ceramic coatings by the laser irradiation, the structure of resulting coatings being dependent on the irradiation conditions, with increase of laser specific energy leading to the formation of initially γ-Al₂O₃ with increasing amounts of α-Al₂O₃ at higher energy. Nano-indentation results reveal that the laser processing results in significant improvement in hardness and Young's modulus of the alumina-coated surface and, at optimum, can achieve the mechanical properties at the same level as pure α-alumina ceramic, much higher than those of the as-dried xerogel coating.     

Fabrication of corrosion-resistant Al2O3–CeO2 composite coating on AA7075 via plasma electrolytic oxidation coupled with electrophoretic deposition

Al₂O₃–CeO₂ composite coating was fabricated on AA7075 by combining plasma electrolytic oxidation (PEO) with electrophoretic deposition (EPD). CeO₂ nanoparticles are electrophoretically incorporated into the plasma electrolytic oxidized Al₂O₃ coatings by the synergetic effect of PEO and EPD processes. The passivation behavior of Al₂O₃ and inhibiting nature of CeO₂ have been studied by the electrochemical corrosion analysis in 3.5 wt% NaCl solution and salt spray corrosion test (SSCT) in 5 wt% NaCl as per ASTM standards. The results showed that the Al₂O₃–CeO₂ composite coating via PEO coupled EPD significantly improved the corrosion resistance (~10³ times higher R_p) compared to the plasma electrolytic oxidized Al₂O₃ coating.     

Mechanical properties and sliding wear behaviour of Al2O3-SiC nanocomposites with 3–20 vol% SiC

Al₂O₃/SiC composites containing different volume fractions (3, 5, 10, 15, and 20 vol%) of SiC particles were produced by conventional mixing of alumina and silicon carbide powders, followed by hot pressing at 1740 °C for 1 h under the pressure of 30 MPa in the atmosphere of Ar. The influence of the volume fraction and size of SiC particles (two different powders with the mean size of SiC particles 40 and 200 nm were used), and final microstructure on mechanical properties and dry sliding wear behaviour in ball-on-disc arrangement were evaluated. The properties of the composites were related to a monolithic Al₂O₃ reference. Microstructure of the composites was significantly affected by the volume fraction of added SiC, with the mean size of alumina matrix grains decreasing with increasing content of SiC particles. The addition of SiC moderately improved the Vickers hardness. Fracture toughness was lower with respect to monolithic Al₂O₃, irrespective of the volume fraction and size of SiC particles. Al₂O₃/SiC nanocomposites conferred significant benefits in terms of wear behaviour under the conditions of mild dry sliding wear. Wear resistance of the alumina reference was poor, especially at the applied load of 50 N. The wear rates of composites markedly decreased with increasing volume fraction of SiC. Wear of the composites was also influenced by the material of counterparts, especially their hardness, with softer counterparts resulting in lower wear rates. All composites wore by a combination of grain pull-out with plastic deformation associated with grooving and small contribution of mechanical wear (micro-fracture). No influence of SiC particle size on wear rate or mechanism of wear was observed in the materials with identical volume fractions of SiC.     

Air plasma-sprayed Y2O3 coatings for Al2O3/Al2O3 ceramic matrix composites

Al₂O₃/Al₂O₃ ceramic matrix composites (CMC) are candidate materials for hot-gas leading components of gas turbines. Since Al₂O₃/Al₂O₃ CMC are prone to hot-corrosion in combustion environments, the development of environmental barrier coatings (EBC) is mandatory. Owing to its favorable chemical stability and thermal properties, Y₂O₃ is considered a candidate EBC material for Al₂O₃/Al₂O₃ CMC. Up to 1 mm thick Y₂O₃ coatings were deposited by means of air plasma spraying (APS) on Al₂O₃/Al₂O₃ CMC with a reaction-bonded Al₂O₃ bond-coat (RBAO). APS Y₂O₃ coatings exhibit a good adherence in the as-deposited state as well as upon isothermal annealing up to 1400 °C. Moreover, furnace cyclic testing performed at 1200 °C revealed an excellent durability. This is explained by the formation of a continuous, approximately 1 μm thick reaction zone at the APS Y₂O₃/RBAO interface. The reaction zone between Y₂O₃ and Al₂O₃ comprises three layers of thermodynamically stable yttrium-aluminates exhibiting strong bonding, respectively.     

Study on energy consumption of Al2O3 coating prepared by cathode plasma electrolytic deposition

Al₂O₃ coatings with large specific surface were prepared on cast nickel-based superalloy K418 by cathode plasma electrolytic deposition (CPED) in aqueous solutions at different concentrations. The significance of energy consumption and a simple calculation method during CPED were proposed, and the influence of electrolyte concentration on current density-voltage curve, energy consumption, and microstructure of coatings were studied. It was found that increasing the concentration of electrolyte can effectively reduce the current density at the initial stage while prolonging the deposition time and stepping up the energy consumption of whole coating preparation. The morphology observation results showed that the pore size of Al₂O₃ coatings enlarges with the increase of the concentration, and the optimum electrolyte concentration is 0.5–1 mol L^?1. Under this condition, the new method of oxidation pretreatment at 950 ℃ on samples for 30 min can efficiently decrease the current density during the early stage of preparation, which is beneficial to the deposition of complex-shaped samples with large size.     

Effect of graphite nanoplatelets on the mechanical properties of alumina-based composites

Al₂O₃-based composites using exfoliated graphite nanoplatelets (xGnPs) have been developed by powder metallurgy (PM) route using both conventional as well as spark plasma sintering (SPS) processes. Al₂O₃-0.2, 0.5, 0.8, 3 and 5 vol% xGnP composites have been developed, and the effect of the addition of xGnP on the density, hardness, fracture toughness and wear behaviour of the various Al₂O₃-xGnP composites have been analyzed. Conventional sintering was done at a temperature of 1650 °C for 2, 3 and 4 h in inert atmosphere, whereas SPS was carried out at 1450 °C under 50 MPa pressure for 5 min. A uniform dispersion of the xGnP in the Al₂O₃ matrix was observed in the composites upto the addition of 3 vol% xGnP. Results indicate that a significant improvement in hardness, wear resistance and fracture toughness of the composites could be achieved by using xGnP as nanofiller. The hardness and fracture toughness of the composites developed by both conventional sintering and SPS show an increase upto the addition of 3 and 0.8 vol% xGnP respectively. The wear resistance of the composites also shows significant improvement upto the addition of 3 vol% xGnP. The composites developed by SPS have been found to possess superior mechanical properties as compared to the composites developed by conventional sintering. The improvement in the mechanical properties can be attributed to the strong interaction between the xGnP and the Al₂O₃ matrix at the interfaces and to the toughening mechanisms such as crack bridging and crack deflection.