Effect of the type of SAN in SAN/CPE blend: Morphology,mechanical, and rheological properties

The effect of the molecular weight and acrylonitrile (AN) content of the styrene-acylonitrile copolymer (SAN) on the morphology, mechanical, and rheological properties of SAN/chlorinated polyethylene (CPE) blends was studied. The interaction between dispersed particle and matrix is expected to be optimal at the 25% AN content of SAN. Phase inversion from a dispersion to a continuous phase appears to occur above 50 wt % CPE. Mechanical properties increased with molecular weight at a constant AN content of SAN. Morphological, mechanical, and rheological properties were more sensitive to the AN content, rather than the molecular weight of SAN. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 27–36, 1998     

Synthesis of high rubber styrene–EPDM–acrylonitrile graft copolymer and its toughening effect on SAN

High rubber styrene–EPDM–acrylonitrile (AES) was prepared by the graft copolymerization of styrene (St) and acrylonitrile (AN) onto ethylene–propylene–diene terpolymer (EPDM) in n‐heptane/toluene cosolvent using benzoyl peroxide as an initiator. The effects of reaction conditions, such as reaction temperature, initiator concentration, EPDM content, the solvent component, and reaction time, on the graft copolymerization are discussed. In addition, according to the research on mechanical properties of the SAN/AES blend, a remarkable toughening effect of AES on SAN resin was found. By means of scanning electron microscopy, the toughening mechanism is proposed to be crazing initiation from rubber particles and shear deformation of SAN matrix. Uniform dispersion of rubber particles, as shown by transmission electron microscopy, is attributed to the good compatibility of SAN and AES. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 416–423, 2004     

Properties of ASA/SAN/NBR ternary blends: effect of AN content in NBR

Abstract

Nitrile–butadiene rubbers (NBRs) with different acrylonitrile (AN) contents were used to toughen acrylonitrile–styrene–acrylic terpolymer/styrene–acrylonitrile copolymer (ASA/SAN) blends. The properties of the ASA/SAN/NBR ternary blends were investigated via dynamic mechanical analysis, heat distortion temperature, Fourier transform infrared spectroscopy and scanning electron microscopy (SEM). The effects of AN content in NBR on physical properties, heat resistance and morphology of the ternary blends were studied. Heat distortion temperature of the blends decreased with increasing AN content of NBR. The impact strength reached the maximum value when 20 phr NBR with 26 wt-%AN content was added. Images (SEM) were in accordance with results of mechanical properties.     

Morphology and physical properties of SAN/NBR blends: The effect of AN content in NBR

Poly(styrene‐co‐acrylonitrile) (SAN), of which the content of acrylonitrile (AN) repeating unit is 32 wt % (SAN32), was blended with poly(butadiene‐co‐acrylonitrile) (NBR). The effects of AN repeating unit content in NBR on the miscibility, morphology, and physical properties of SAN32/NBR (70/30 by weight) blends were studied. Differential scanning calorimetry and the morphology observed by transmission electron microscopy showed that the miscibility between SAN32 and NBR was increased as the AN content in NBR was increased up to 50 wt %. The impact strength and some other mechanical properties of the blends had the maximum value when the AN content in NBR was 34 wt %. In the measurement of viscoelasticity at melt state, SAN32/NBR blends showed yield behavior at low shear rate, and this behavior was most evident when the AN content in NBR was 34 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1861–1868, 2000     

Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Study on the microphase structure and mechanical properties of the blends of acrylonitrile–butadiene–styrene and sodium sulphonated styrene–acrylonitrile ionomer

The tensile properties of the blends containing neat acrylonitrile–butadiene–styrene (ABS), styrene–acrylonitrile (SAN) and the sodium sulphonated SAN ionomer have been investigated as a function of ion content of the ionomer in the blend. The tensile toughness and strength of the blends showed maximum values at a certain ion content of the ionomer in the blend. This is attributed to the enhanced tensile properties of the SAN ionomer by introduction of ionic groups into SAN and the interfacial adhesion between the rubber and matrix phase in the blend. The interfacial adhesion was quantified by NMR solid echo experiments. The amount of interphase for the blend containing the SAN ionomer with low ion content (3·1mol%) was nearly the same as that of ABS, but it decreased with the ion content of the ionomer for the blend with ion content greater than 3·1mol%. Changing the ionomer content in the blends showed a positive deviation from the rule of mixtures in tensile properties of the blends containing the SAN ionomer with low ion content. This seems to result from the enhanced tensile properties of the SAN ionomer, interfacial adhesion between the rubber and matrix, and the stress concentration effect of the secondary particles. © 1998 SCI.     

Toughness,dynamic mechanical property,and morphology of polyvinylchloride/acrylonitrile‐styrene‐butyl acrylate blends

Acrylonitrile‐styrene‐butyl acrylate (ASA) graft copolymers with different acrylonitrile (AN) contents, the core‐shell ratio, and tert‐dodecyl mercaptan (TDDM) amounts were synthesized by seed emulsion polymerization. Polyvinylchloride (PVC)/ASA blends were prepared by melt blending ASA graft copolymers with PVC resin. Then the toughness, dynamic mechanical property, and morphology of the PVC/ASA blends were investigated. The results indicated that the impact strength of the PVC/ASA blends increased and then decreased with the increase of the AN content in poly(styrene‐co‐acrylonitrile (SAN) copolymer, and increased with the increase of the core‐shell ratio of ASA. It was shown that brittle‐ductile transition of PVC/ASA blends was dependent on poly(butyl acrylate) (PBA) rubber content in blends and independent of AN content in SAN copolymer. The introduction of TDDM made the toughness of PVC/ASA blends poor. Dynamic mechanical analysis (DMA) curves exhibited that PVC and SAN copolymers were immiscible over the entire AN composition range. From scanning electron microscopy (SEM), it was found that the dispersion of ASA in PVC/ASA blends was dependent on the AN content in SAN copolymer and TDDM amounts. J. VINYL ADDIT. TECHNOL., 22:43–50, 2016. © 2014 Society of Plastics Engineers     

Morphology and physical properties of SAN/NBR blends: The effect of AN content and melt viscosity of SAN

To study the effect of dispersed poly(butadiene-co-acrylonitrile) (NBR) rubber size on the physical properties of poly(styrene-co-acrylonitrile) (SAN)/NBR blends, SANs with various melt viscosities and acrylonitrile (AN) contents were examined. The dispersed size of NBR, whose AN content is 30 wt %, was reduced as the melt viscosity of the SAN matrix was increased or as the AN content of the SAN matrix was reduced in the range of 19–32 wt %. As the melt viscosity of the SAN matrix was increased, the damping peak of the NBR phase moved to a higher temperature, and as the AN content of SAN was reduced, the damping peak of the SAN phase moved to a lower temperature. Higher values of impact strength and elongation at break and reduced yield behavior at a low shear rate were observed at a finer dispersion of NBR. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 935–941, 1999     

悬浮聚合法制备ASA树脂及其性能研究

采用悬浮聚合法,以丙烯酸丁酯、苯乙烯和丙烯腈为原料,合成了一系列丙烯酸丁酯-苯乙烯-丙烯腈(ASA)树脂。考察了橡胶相聚丙烯酸丁酯(PBA)、甲基丙烯酸烯丙酯(ALMA)和叔十二碳硫醇(TDDM)用量对ASA树脂的力学性能影响。结果表明:PBA质量分数达到20%后,ASA树脂的冲击强度大幅增加。TDDM的加入使苯乙烯-丙烯腈(SAN)的相对分子质量降低,当其质量分数低于1%时,ASA树脂的冲击强度呈升高趋势,质量分数高于1%时其冲击强度大幅降低。随PBA含量增加,ASA树脂的拉伸强度减小,断裂伸长率变大。     

影响苯乙烯丙烯腈在聚丁二烯乳胶粒上接枝共聚反应的因素

采用种子乳液聚合技术在聚丁二烯 ( PB)乳胶粒上接枝共聚苯乙烯 ( St)和丙烯腈 ( AN) ,合成了一系列 PB-g-SAN共聚物 ( ABS)。将这些共聚物用丙酮溶解并在超速离心机上将 PB-g-SAN和未接枝在 PB上的游离 SAN分离 ,计算出 SAN在 PB上的接枝率和接枝效率。通过改变共聚单体的组成和加料时间 ,研究了接枝率和接枝效率的变化。结果表明 SAN的接枝率随着 PB含量的增加而降低 ,在共聚单体中增加引发剂 ( CHP)和分子量调节剂 ( TD-DM)的含量 ,SAN在 PB上的接枝率和接枝效率表现出了下降的趋势 ,而共聚单体的配比 St/ AN和加料时间对接枝率和接枝效率的影响不大。     

Structure–properties relationship in toughening of poly(butylene terephthalate) with core–shell modifier

The performance of acrylonitrile–butadiene–styrene (ABS) core–shell modifier with different grafting degree, acrylonitrile (AN) content, and core–shell ratio in toughening of poly(butylene terephthalate) (PBT) matrix was investigated. Results show PBT/ABS blends fracture in ductile mode when the grafting degree is high, and with the decrease of grafting degree PBT/ABS blends fracture in a brittle way. The surface of rubber particles cannot be covered perfectly for ABS with low grafting degree and agglomeration will take place; on the other hand, the entanglement density between SAN and PBT matrix decreases because of the low grafting degree, inducing poor interfacial adhesion. The compatibility between PBT and ABS results from the strong interaction between PBT and SAN copolymer and the interaction is influenced by AN content. Results show ABS cannot disperse in PBT matrix uniformly when AN content is zero and PBT/ABS fractures in a brittle way. With the addition of AN in ABS, PBT/ABS blends fracture in ductile mode. The core–shell ratio of ABS copolymers has important effect on PBT/ABS blends. When the core–shell ratio is higher than 60/40 or lower than 50/50, agglomeration or cocontinuous structure occurs and PBT/ABS blends display lower impact strength. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 5363–5371, 2006     

Compatibility enhancement of ABS/PVC blends

The compatibilizing effect of poly(styrene-co-acrylonitrile) (SAN) whose acrylonitrile (AN) content is 25 wt % (SAN 25) in poly(acrylonitrile-co-butadiene-co-styrene) (ABS)/poly(vinyl chloride) (PVC) blend was studied when the AN content of the matrix SAN in ABS was 35 wt % (SAN 35). When some amount of matrix SAN 35 was replaced by SAN 25 in a ABS/PVC (50/50 by weight) blend, the mixed phase of SAN and PVC at the interface was thickened, and about a twofold increase of impact strength was observed. The changes in morphology, dynamic mechanical properties, and rheological properties by the compatibilizing effect of SAN 25 were observed. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 705–709, 1998     

ABS树脂的性能与形态结构设计 ⅠSAN在PB橡胶粒子上接枝率的控制及其对ABS树脂结构和性能的影响

采用种子乳液聚合技术在聚丁二烯乳胶粒上接枝共聚苯乙烯和丙烯腈 ,通过改变共聚单体和聚丁二烯的投料比合成了一系列PB g SAN共聚物 ,将这些共聚物与SAN树脂进行熔融共混制得了ABS树脂。研究了投料比对SAN在PB上的接枝率、SAN的分子量和ABS树脂的形态结构及性能的影响。结果发现 ,随着投料比的增加 ,SAN在PB上的接枝率及SAN的分子量提高 ,接枝率和SAN分子量共同作用影响着ABS树脂的冲击韧性和加工性能。形态结构研究结果表明 ,投料比不仅影响着橡胶粒子在SAN基体中的分散程度 ,而且影响着橡胶粒子的内部结构 ,随着投料比的增加 ,橡胶粒子在基体中的分散程度提高 ,其内部的包容结构增多并导致了橡胶粒子粒径的增大。     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

Morphology and mechanical behaviors of rigid organic particles reinforced polycarbonate

For the purpose of promoting mechanical properties of bisphenol-A polycarbonate (PC) reinforced by rigid organic styrene–acrylonitrile copolymer (SAN) particles, styrene/acrylonitrile/glycidyl methacrylate terpolymer (SAG) was synthesized and applied as compatibilizer for PC/SAN blends. It is found that the phase morphology of PC/SAN/SAG blends is closely related with their mechanical properties. Large continuously distributed SAN phase or spherical dispersed SAN particles with average diameter over 2 μm tend to trigger premature tensile failure of blends due to stress concentration. The incorporation of SAG can simultaneously reinforce and toughen PC/SAN blends by controlling the size and distribution of the dispersed SAN particles. For the blends with fixed PC/SAN ratio, the elongation at break and fracture energy are markedly improved when SAN domain size is reduced by adding appropriate amount of SAG. Typically, for blends with a PC/SAN ratio of 75/25, adding 3 wt% SAG will cause the average diameter of SAN particles to reduce from 2.35 ± 1.20 to 0.74 ± 0.25 μm, meanwhile up to 95% increment in elongation at break and 115% increment in fracture energy is achieved.     

Thermoplastic elastomeric blend of nitrile rubber and poly(styrene‐co‐acrylonitrile). I. Effect of mixing sequence and dynamic vulcanization on mechanical properties

The effects of dynamic vulcanization and blend ratios on mechanical properties and morphology of thermoplastic elastomeric (TPE) compositions, based on blends of nitrile rubber (NBR) and poly(styrene‐co‐acrylonitrile) (SAN), were studied. The TPE composition prepared by adding a rubber‐curatives masterbatch to softened SAN yields higher mechanical properties than that prepared by adding curatives to the softened plastic–rubber preblend. The blends having a higher rubber–plastic ratio (60 : 40 to 80 : 20) display thermoplastic elastomeric behavior, whereas those having a higher plastic–rubber ratio (50 : 50 to 90 : 10) display the behavior of impact‐resistant plastics. DSC studies revealed that NBR and SAN are thermodynamically immiscible. SEM studies of the thermoplastic elastomeric compositions show that SAN forms the matrix in which fine particles of NBR form the dispersed phase. It was further confirmed by dynamic mechanical thermal analysis. Dynamic vulcanization causes a decrease in the size of dispersed particles and improvement in mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1976–1987, 2003     

Flow properties of ABS (acrylonitrile–butadiene–styrene) terpolymer

ABS (acrylonitrile–butadiene–styrene) terpolymer is a two-phase thermoplastic with SAN (styrene–acrylonitrile) copolymer constituting the continuous phase (matrix). The flow properties of ABS with varying molecular parameters were studied using a capillary viscometer at the shear rate range encountered in its processing. The viscosity-average molecular weights (M_v) of matrix SAN with 26% acrylonitrile content are in the range of 90,000 to 150,000, and M_v of poly-butadiene-are in the range of 150,000 to 170,000. The weight-average molecular weight of the matrix SAN is the main controlling factor for the flow properties of ABS at low shear rate, while the molecular weight distribution of the matrix SAN becomes increasingly important with the increase of shear rate. The presence of SAN grafted polybutadiene increases the melt viscosity of ABS by 40–60% over comparable free SAN copolymer and also decreases the activation energy at constant shear stress to 24–25 kcal/mole from the 33–36 kcal/mole for free SAN. The die swell of ABS and SAN can be correlated with the dynamic shear modulus G′, and the melt fracture of ABS and SAN starts at G′ equal to 3.6 × 10⁶ dynes/cm².     

小粒橡胶粒子对SAN树脂的增韧作用

采用PB-g－SAN和SBR－g－SAN两种弹性体粒子分别与SAN树脂熔融共混,制得了一系列ABS树脂,研究了ABS树脂的形态结构和力学性能,结果发现,PB和SBR橡胶粒子均匀地分散在SAN基体中,其径分别为0.28μm和0.05μm左右。力学性能结果表明,在SAN树脂中随着PB-g－SAN含量的增加,ABS的冲击强度不断提高,而SBR小橡胶粒子不能增韧SAN树脂,但当SAN树脂中含有15％的PB-g－SAN共聚物时,随着SBR－g－SAN含量的增加,ABS树脂的冲击强度不断提高,SBR－g－SAN这种小橡胶粒子又表现出良好的增韧作用。     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

PVC／ABS共混体系的相容性与形态结构研究

采用种子乳液聚合技术在聚丁二烯（PB）乳胶粒子上接枝共聚苯乙烯（St）、α-甲基苯乙烯（α—MSt）和丙烯腈（AN）单体,合成了一系列不同AN结合量的ABS和α—MABS接枝共聚物。将其与聚氯乙烯（PVC）树脂熔融共混制得了PVC／AtkS共混物,利用扫描电镜（SEM）、透射电镜（TEM）和动态力学分析仪（DMA）对共混物的相容性和相结构进行了表征。结果发现,在PVC／ABS共混体系中,尽管改变接枝SAN共聚物的AN结合量,PVC和ABS接枝共聚物均为不相容体系;在ABS接枝共聚物中引入α-MSt后,当接枝SAN共聚物的AN结合量为18．7％～23．6％（质量分数）时,共混物在室温以上只存在1个tanδ峰,共混物成为相容体系,当AN结合量达到32．1％（质量分数）时,共混物成为部分相容体系。共混物的相区尺寸明显地依赖于接枝SAN共聚物中的AN结合量,与动态力学性能结果表现出良好的吻合。