Electrochemical supercapacitor behavior of Ni3(Fe(CN)6)2(H2O) nanoparticles

Nanosized Ni₃(Fe(CN)₆)₂(H₂O) was prepared by a simple co-precipitation method. The electrochemical properties of the sample as the electrode material for supercapacitor were studied by cyclic voltammetry (CV), constant charge/discharge tests and electrochemical impedance spectroscopy (EIS). A specific capacitance of 574.7 F g⁻¹ was obtained at the current density of 0.2 A g⁻¹ in the potential range from 0.3 V to 0.6 V in 1 M KNO₃ electrolyte. Approximately 87.46% of specific discharge capacitance was remained at the current density of 1.4 A g⁻¹ after 1000 cycles.     

High-rate cathodes based on Li3V2(PO4)3 nanobelts prepared via surfactant-assisted fabrication

In this work, we have synthesized monoclinic Li₃V₂(PO₄)₃ nanobelts via a single-step, solid-state reaction process in a molten hydrocarbon. The as-prepared Li₃V₂(PO₄)₃ nanoparticles have a unique nanobelt shape and are ∼50-nm thick. When cycled in a voltage range between 3.0 V and 4.3 V at a 1C rate, these unique Li₃V₂(PO₄)₃ nanobelts demonstrate a specific discharge capacity of 131 mAh g⁻¹ (which is close to the theoretical capacity of 132 mAh g⁻¹) and stable cycling characteristics.     

Evaluation of Ba2(In0.8Ti0.2)2O5.2−n(OH)2n as a potential electrolyte material for proton-conducting solid oxide fuel cell

Electrochemical measurements of fuel cells based on proton conductor electrolyte Ba₂(In_0.8Ti_0.2)₂O_5.2−n(OH)_2n and prepared through a tape casting process and a co-pressing of anode-composite powder and electrolyte tape were performed at 500 °C under wet H₂. The varying parameter between the prepared cells was the thickness of the electrolyte that can be controlled during the tape casting process. The maximum power density was obtained for the cell with the thinnest electrolyte (35 μm) and was about 22 mW cm⁻² with an ohmic resistance about 2 Ω cm² at 500 °C.     

Synthesis and improved electrochemical performances of porous Li3V2(PO4)3/C spheres as cathode material for lithium-ion batteries

Spherical Li₃V₂(PO₄)₃/C composites are synthesized by a soft chemistry route using hydrazine hydrate as the spheroidizing medium. The electrochemical properties of the materials are investigated by galvanostatic charge-discharge tests, cyclic voltammograms and electrochemical impedance spectrum. The porous Li₃V₂(PO₄)₃/C spheres exhibit better electrochemical performances than the solid ones. The spherical porous Li₃V₂(PO₄)₃/C electrode shows a high discharge capacity of 129.1 and 125.6 mAh g⁻¹ between 3.0 and 4.3 V, and 183.8 and 160.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.2 and 1 C, respectively. Even at a charge-discharge rate of 15 C, this material can still deliver a discharge capacity of 100.5 and 121.5 mAh g⁻¹ in the potential regions of 3.0-4.3 V and 3.0-4.8 V, respectively. The excellent electrochemical performance can be attributed to the porous structure, which can make the lithium ion diffusion and electron transfer more easily across the Li₃V₂(PO₄)₃/electrolyte interfaces, thus resulting in enhanced electrode reaction kinetics and improved electrochemical performance.     

Li3V2(PO4)3/C composite as an intercalation-type anode material for lithium-ion batteries

The carbon coated monoclinic Li₃V₂(PO₄)₃ (LVP/C) powder is successfully synthesized by a carbothermal reduction method using crystal sugar as the carbon source. Its structure and physicochemical properties are investigated using X-ray diffraction (XRD), scanning electron microscopy, high-resolution transmission electron microscopy and electrochemical methods. The LVP/C electrode exhibits stable reversible capacities of 203 and 102 mAh g⁻¹ in the potential ranges of 3.0-0.0 V and 3.0-1.0 V versus Li⁺/Li, respectively. It is identified that the insertion/extraction of Li⁺ undergoes a series of two-phase transition processes between 3.0 and 1.6 V and a single phase process between 1.6 and 0.0 V. The ex situ XRD patterns of the electrodes at various lithiated states indicate that the monoclinic structure can still be retained during charge-discharge process and the insertion/deinsertion of lithium ions occur reversibly, which provides an excellent cycling stability with high energy efficiency.     

Iron oxide (n-Fe2O3) nanowire films and carbon modified (CM)-n-Fe2O3 thin films for hydrogen production by photosplitting of water

Iron oxide n-Fe₂O₃ nanowire photoelectrodes were synthesized by thermal oxidation of Fe metal sheet (Alfa Co. 0.25 mm thick) in an electric oven then tested for their photoactivity. The photoresponse of the n-Fe₂O₃ nanowires was evaluated by measuring the rate of water splitting reaction to hydrogen and oxygen, which is proportional to photocurrent density, J_p. The optimized electric oven-made n-Fe₂O₃ nanowire photoelectrodes showed photocurrent densities of 1.46 mA cm⁻² at measured potential of 0.1 V/SCE at illumination intensity of 100 mW cm⁻² from a Solar simulator with a global AM 1.5 filter. For the optimized carbon modified (CM)-n-TiO₂ synthesized by thermal flame oxidation the photocurrent density for water splitting was found to increase by two fold to 3.0 mA cm⁻² measured at the same measured potential and the illumination intensity. The carbon modified (CM)-n-Fe₂O₃ electrode showed a shift of the open circuit potential by −100 mV/SCE compared to undoped n-Fe₂O₃ nanowires. A maximum photoconversion efficiency of 2.3% at applied potential of 0.5 V/E_aoc was found for CM-n-Fe₂O₃ compared to 1.69% for n-Fe₂O₃ nanowires at higher applied potential of 0.7 V/E_aoc. These CM-n- Fe₂O₃ and n- Fe₂O₃ nanowires thin films were characterized using photocurrent density measurements under monochromatic light illumination, UV-Vis spectra, X-ray diffraction (XRD) and scanning electron microscopy (SEM).     

Synthesis of plate-like Li3V2(PO4)3/C as a cathode material for Li-ion batteries

Plate-like Li₃V₂(PO₄)₃/C composite is synthesized via a solution route followed by solid-state reaction. The Li₃V₂(PO₄)₃/C plates are 40-100 nm in thicknesses and 2-10 μm in lengths. TEM images show that a uniform carbon layer with a thickness of 5.3 nm presents on the surfaces of Li₃V₂(PO₄)₃ plates. The apparent Li-ion diffusion coefficient of the plate-like Li₃V₂(PO₄)₃/C is calculated to be 2.7 × 10⁻⁸ cm² s⁻¹. At a charge-discharge rate of 3 C, the plate-like Li₃V₂(PO₄)₃/C exhibits an initial discharge capacity of 125.2 and 133.1 mAh g⁻¹ in the voltage ranges of 3.0-4.3 and 3.0-4.8 V, respectively. After 500 cycles, the electrodes still can deliver a discharge capacity of 111.8 and 97.8 mAh g⁻¹ correspondingly, showing a good cycling stability.     

Development of Ag-(BaO)0.11(Bi2O3)0.89 composite cathodes for intermediate temperature solid oxide fuel cells

The electrochemical performances of Ag-(BaO)_0.11(Bi₂O₃)_0.89 (BSB) composite cathodes on Ce_0.8Sm_0.2O_1.9 electrolytes have been investigated for intermediate temperature solid oxide fuel cells (ITSOFCs) using ac impedance spectroscopy from 500 to 700 °C. Results indicate that the electrochemical properties of these composites are quite sensitive to the composition and the microstructure of the cathode. The optimum BSB addition (50% by volume) to Ag resulted in about 20 times lower area specific resistance (ASR) at 650 °C. The ASR values for the Ag50-BSB and Ag cathodes were 0.32 and 6.5 Ω cm² at 650 °C, respectively. The high performances of Ag-BSB cathodes are determined by the high catalytic activity for oxygen dissociation and ionic conductivity of BSB, and by the excellent catalytic activity for oxygen reduction of silver. The maximum power density of the Ag50-BSB cathode was 224 mWcm⁻² at 650 °C, which classify this composite as a promising material for ITSOFC.     

Electrochemical profile of an asymmetric supercapacitor using carbon-coated LiTi2(PO4)3 and active carbon electrodes

In this work, we reported an asymmetric supercapacitor in which active carbon (AC) was used as a positive electrode and carbon-coated LiTi₂(PO₄)₃ as a negative electrode in 1 M Li₂SO₄ aqueous electrolyte. The LiTi₂(PO₄)₃/AC hybrid supercapacitor showed a sloping voltage profile from 0.3 to 1.5 V, at an average voltage near 0.9 V, and delivered a capacity of 30 mAh g⁻¹ and an energy density of 27 Wh kg⁻¹ based on the total weight of the active electrode materials. It exhibited a desirable profile and maintained over 85% of its initial energy density after 1000 cycles. The hybrid supercapacitor also exhibited an excellent rate capability, even at a power density of 1000 W kg⁻¹, it had a specific energy 15 Wh kg⁻¹ compared with 24 Wh kg⁻¹ at the power density about 200 W kg⁻¹.     

Synthesis and electrochemical performances of Li3V2(PO4)3/(Ag + C) composite cathode

Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C and Li₃V₂(PO₄)₃/(Ag + C) composites as cathodes for Li ion batteries are synthesized by carbon-thermal reduction (CTR) method and chemical plating reactions. The microstructure and morphology of the compounds are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Li₃V₂(PO₄)₃/(Ag + C) particles are 0.5-1 μm in diameters. As compared to Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C, the Li₃V₂(PO₄)₃/(Ag + C) composite cathode exhibits high discharge capacity, good cycle performance (140.5 mAh g⁻¹ at 50th cycle at 1 C, 97.3% of initial discharge capacity) and rate behavior (120.5 mAh g⁻¹ for initial discharge at 5 C) for the fully delithiated (3.0-4.8 V) state. Electrochemical impedance spectroscopy (EIS) measurements show that the carbon and silver co-modification decreases the charge transfer resistance of Li₃V₂(PO₄)₃/(Ag + C) cathode, and improves the conductivity and boosts the electrochemical performance of the electrode.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

Characteristics of Li3V2(PO4)3/C powders prepared by ultrasonic spray pyrolysis

Li₃V₂(PO₄)₃ and Li₃V₂(PO₄)₃/C powders are prepared by ultrasonic spray pyrolysis from spray solutions with and without sucrose. The precursor powders have a spherical shape and the crystal structure of V₂O₃ irrespective of the concentration of sucrose in the spray solution. The powders post-treated at 700 °C have the pure crystal structure of the Li₃V₂(PO₄)₃ phase irrespective of the concentration of sucrose in the spray solution. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a non-spherical shape and hard aggregation. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solution with sucrose have a spherical shape and non-aggregation characteristics. The Li₃V₂(PO₄)₃ powders prepared from the spray solution without sucrose have a low initial discharge capacity of 122 mAh g⁻¹. However, the Li₃V₂(PO₄)₃/C powders prepared from the spray solutions with 0.1, 0.3, and 0.5 M sucrose have initial discharge capacities of 141, 130, and 138 mAh g⁻¹, respectively. After 25 cycles, the discharge capacities of the powders formed from the spray solutions with and without 0.1 M sucrose are 70% and 71% of the initial discharge capacities, respectively.     

Novel FexCr2−x(MoO4)3 electrocatalysts for oxygen evolution reaction

Transition metal mixed oxides of Fe, Cr and Mo with nominal compositional formula, Fe_xCr_2−x(MoO₄)₃ (x = 0, 0.25, 0.50 and 0.75) have been obtained by a co-precipitation method and investigated for their structural and electrocatalytic properties by XRD, TEM, XPS, BET, electrochemical impedance spectroscopy and anodic Tafel polarization. Results show that introduction of Fe for Cr from 0.25 to 0.75 mol into the Cr₂(MoO₄)₃ matrix improved the electrocatalytic activity toward the O₂ evolution reaction (OER) in 1 M KOH considerably; the magnitude of improvement being maximum with 0.5 mol Fe. Values of the Tafel slope were close to 35 mV at low and 2.303RT/F at high overpotentials on Fe-substituted oxides. The OER follows nearly second order kinetics in OH⁻ concentration at low overpotentials.     

Li3V2(PO4)3 cathode material synthesized by chemical reduction and lithiation method

The monoclinic-type Li₃V₂(PO₄)₃ cathode material was synthesized via calcining amorphous Li₃V₂(PO₄)₃ obtained by chemical reduction and lithiation of V₂O₅ using oxalic acid as reducer and lithium carbonate as lithium source in alcohol solution. The amorphous Li₃V₂(PO₄)₃ precursor was characterized by using TG–DSC and XPS. The results showed that the V⁵⁺ was reduced to V³⁺ by oxalic acid at ambient temperature and pressure. The prepared Li₃V₂(PO₄)₃ was characterized by XRD and SEM. The results indicated the Li₃V₂(PO₄)₃ powder had good crystallinity and mesoporous morphology with an average diameter of about 30 nm. The pure Li₃V₂(PO₄)₃ exhibits a stable discharge capacity of 130.08 mAh g⁻¹ at 0.1 C (14 mA g⁻¹).     

A fast synthesis of Li3V2(PO4)3 crystals via glass-ceramic processing and their battery performance

A synthesis of Li₃V₂(PO₄)₃ being a potential cathode material for lithium ion batteries was attempted via a glass-ceramic processing. A glass with the composition of 37.5Li₂O-25V₂O₅-37.5P₂O₅ (mol%) was prepared by a melt-quenching method and precursor glass powders were crystallized with/without 10 wt% glucose in N₂ or 7%H₂/Ar atmosphere. It was found that heat treatments with glucose at 700 °C in 7%H₂/Ar can produce well-crystallized Li₃V₂(PO₄)₃ in the short time of 30 min. The battery performance measurements revealed that the precursor glass shows the discharge capacity of 14 mAh g⁻¹ at the rate of 1 μA cm⁻² and the glass-ceramics with Li₃V₂(PO₄)₃ prepared with glucose at 700 °C in 7%H₂/Ar show the capacities of 117-126 mAh g⁻¹ (∼96% of the theoretical capacity) which are independent of heat treatment time. The present study proposes that the glass-ceramic processing is a fast synthesizing route for Li₃V₂(PO₄)₃ crystals.     

High lithium ionic conductivity in the garnet-type oxide Li7−X La3(Zr2−X, NbX)O12 (X = 0-2)

Lithium garnet-type oxides Li_7−XLa₃(Zr_2−X, Nb_X)O₁₂ (X = 0-2) were synthesized by a solid-state reaction, and their lithium ion conductivity was measured using an AC impedance method at temperatures ranging from 25 to 150 °C in air. The lithium ion conductivity increased with increasing Nb content, and reached a maximum of ∼0.8 mS cm⁻¹ at 25 °C. By contrast, the activation energy reached a minimum of ∼30 kJ mol⁻¹ at the same point with X = 0.25. The potential window was examined by cyclic voltammetry (CV), which showed lithium deposition and dissolution peaks around 0 V vs. Li⁺/Li, but showed no evidence of other reactions up to 9 V vs. Li⁺/Li.     

Synthesis and performance of Li3(V1−xMgx)2(PO4)3 cathode materials

In order to search for cathode materials with better performance, Li₃(V_1−xMg_x)₂(PO₄)₃ (0, 0.04, 0.07, 0.10 and 0.13) is prepared via a carbothermal reduction (CTR) process with LiOH·H₂O, V₂O₅, Mg(CH₃COO)₂·4H₂O, NH₄H₂PO₄, and sucrose as raw materials and investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM) and electrochemical impedance spectrum (EIS). XRD shows that Li₃(V_1−xMg_x)₂(PO₄)₃ (x = 0.04, 0.07, 0.10 and 0.13) has the same monoclinic structure as undoped Li₃V₂(PO₄)₃ while the particle size of Li₃(V_1−xMg_x)₂(PO₄)₃ is smaller than that of Li₃V₂(PO₄)₃ according to SEM images. EIS reveals that the charge transfer resistance of as-prepared materials is reduced and its reversibility is enhanced proved by the cyclic votammograms. The Mg²⁺-doped Li₃V₂(PO₄)₃ has a better high rate discharge performance. At a discharge rate of 20 C, the discharge capacity of Li₃(V_0.9Mg_0.1)₂(PO₄)₃ is 107 mAh g⁻¹ and the capacity retention is 98% after 80 cycles. Li₃(V_0.9Mg_0.1)₂(PO₄)₃//graphite full cells (085580-type) have good discharge performance and the modified cathode material has very good compatibility with graphite.     

TiO2(B) as a promising high potential negative electrode for large-size lithium-ion batteries

Needle-like TiO₂(B) powder was obtained from K₂Ti₄O₉ precursor by ion exchange to protons, followed by dehydration. The charge and discharge characteristics of the TiO₂(B) powder were investigated as a high potential negative electrode in lithium-ion batteries. It had a high discharge capacity of 200–250 mAh g⁻¹ at around 1.6 V vs. Li/Li⁺, which was comparable with that of TiO₂(B) nanowires and nanotubes prepared via a hydrothermal reaction in alkaline solution. It showed very good cycleability, and gave a discharge capacity of 170 mAh g⁻¹ even in the 650th cycle. It also had a high rate capability, and gave a discharge capacity of 106 mAh g⁻¹ even at 10 °C.     

Synthesis and performance of carbon-coated Li3V2(PO4)3 cathode materials by a low temperature solid-state reaction

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials can be synthesized by a low temperature solid-state reaction route. The influences of different heat treatments on the LVP have been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods. In the range of 3.0-4.3 V, both LVP/C electrodes present good rate capability and excellent cyclic performance. It is found that the sample (LVP1/C) prepared by the two-step heat treatment with pre-sintering at 350 °C delivers the initial discharge capacity of 99.8 mAh g⁻¹ at 10 C charge-discharge rate and still retains 95.8 mAh g⁻¹ after 300 cycles. For the sample (LVP2/C) synthesized by the one-step heat treatment, 95.9 and 90.0 mAh g⁻¹ are obtained in the 1st and 300th cycles at 10 C rate, respectively. Our results based on the XRD patterns and the SEM images suggest that the good rate capability and cyclic performance may be owing to the pure phases, small particles, large specific surface areas and residual carbon. In the range of 3.0-4.8 V, compared with the LVP2/C, the LVP1/C also exhibits better performance.     

Bulk conduction and relaxation in [(ZrO2)1−x(CeO2)x]0.92(Y2O3)0.08 (0 ≤ x ≤ 1) solid solutions at intermediate temperatures

Bulk conduction and relaxation of the [(ZrO₂)_1−x(CeO₂)_x]_0.92(Y₂O₃)_0.08 (0 ≤ x ≤ 1) solid solutions were studied using impedance spectroscopy at intermediate temperatures (200-500 °C). The bulk conductivity as a function of x shows a “V-shape” variation which is a competitive effect of the defect associates and the lattice parameter. In the ZrO₂-rich region (x < 0.5) CeO₂ doping increases the concentration of defect associates which limits the mobility of the oxygen vacancies; in the CeO₂-rich region (x > 0.5) the increase of x increases the lattice parameter which enlarges the free channel for oxygen vacancy migration. Further analysis indicates the ionic radius of the tetravalent dopant determines the composition dependence of the ionic conductivity of the solid solutions. When doping YSZ with other tetravalent dopant with similar ionic radius with Zr⁴⁺, e.g., Hf⁴⁺, such “V-shape” composition dependence of the bulk conductivity cannot be observed.