Migration of Ti from nano-TiO2-polyethylene composite packaging into food simulants

An analytical method based on ICP-MS was developed for the determination of Ti in food simulants (3% (w/v) aqueous acetic acid and 50% (v/v) aqueous ethanol). The method was used to determine the migration of Ti from nano-TiO₂-PE films used for food packaging into food simulants under different temperature and migration time conditions. The maximum migration amounts into 3% (w/v) aqueous acetic acid were 1.4 ± 0.02, 6.3 ± 0.5 and 12.1 ± 0.2 μg kg^?1 at 25, 70 and 100°C, respectively, while into 50% (v/v) aqueous ethanol, the maximum migration amounts were 0.5 ± 0.1, 0.6 ± 0.03 and 2.1 ± 0.1 μg kg^?1 at 25, 70 and 100°C, respectively. Increasing the additive content in the film promoted migration of nanoparticles. The results indicated that the migration of nanoparticles might occur via dissolution from the surface and cut edges of the solid phase (film) into the liquid phase (food simulant).     

Migration of silver from commercial plastic food containers and implications for consumer exposure assessment

Food storage containers with embedded silver as an antibacterial agent promise longer durability of food. For risk assessment the release of this silver into the stored food and resulting human exposure need to be known. For the purpose of exposure assessment, silver migration from commercial plastic containers with declared content of ‘nano-’ or ‘micro-silver’ into different food simulants (water, 10% ethanol, 3% acetic acid, olive oil) was quantitatively determined by ICP-MS and the form of the released silver was investigated. The highest migration of silver was observed for the acidic food simulant with 30 ng silver cm^?2 contact surface within 10 days at 20°C. In a second and third use cycle, migration dropped by a factor of up to 10, so that the maximum cumulated release over three use cycles was 34 ng cm^?2. The silver release over time was described using a power function and a numerical model that simulates Fickian diffusion through the plastic material. The released silver was found to be in ionic form, but also in the form of silver nanoparticles (around 12%). Consumer exposure to the total amount of silver released from the food containers is low in comparison with the background silver exposure of the general population, but since natural background concentrations are only known for ionic silver, the exposure to silver nanoparticles is not directly comparable with a safe background level.     

Target and non-target analysis of migrants from PVC-coated cans using UHPLC-Q-Orbitrap MS: evaluation of long-term migration testing

A simple, rapid and sensitive method for analyzing multi-target and non-target additives in polyvinyl chloride (PVC) food can coatings using ultra-high-performance liquid chromatography coupled to quadrupole-orbital ion-trap mass spectrometry was developed. This procedure was used to study the behaviour of a cross-linking agent, benzoguanamine (BGA), two slip agents, oleamide and erucamide, and 18 other commonly used plasticisers including phthalates, adipates, sebacates, acetyl tributyl citrate and epoxidised soybean or linseed oils. This optimised method was used to detect these analytes in food simulants (water and 3% acetic acid) in a long-term migration test of PVC-coated food cans for a period ranging from 1 day to 1.5 years at 40°C. Although very low detection limits (5 ng ml^–1) were obtained for the majority of compounds, none of the monitored plasticisers and slip agents was detected in simulants extracted from cans over the period of the test. However, the presence of BGA in both aqueous food simulants was confirmed based on high-resolution mass spectrometry, product ion spectra and analysis of a reference standard. The BGA concentration in both simulants continued to increase with storage time: after 1.5 years storage in aqueous food simulants at 40°C, BGA was detected at concentrations up to 84 µg dm^–2. We believe this is the first study describing the long-term migration capacity of BGA from any vinyl coating material intended for use in PVC-coated food cans. Our results may have implications for migration test protocols for food cans that will be stored for extended time periods.     

Migration of photoinitiators from paper to fatty food simulants: experimental studies and model application

The migration of five different photoinitiators from kraft paper to two fatty food simulants, Tenax^® and 95% ethanol, was investigated under different conditions. The effects of temperature and storage time, as well as the physicochemical properties of the photoinitiators on migration, were discussed. Mathematical models based on Fick’s second law generated from two cases, single- and two-side contacts, were applied to predict the migration behaviour from the paper to the food simulants. The partition coefficients estimated from the model decreased with temperature. The diffusion coefficients of the selected photoinitiators from the paper ranged from 1.55 × 10^–10 to 7.54 × 10^–9 cm² s^?1 for Tenax and from 2.79 × 10^–9 to 8.03 × 10^–8 cm² s^?1 for 95% ethanol. The results indicate that the applied model can predict the migration of photoinitiators in the initial short period before equilibrium, and the migration from paper to Tenax through a single-side contact demonstrated an especially high concordance.     

A Miniaturized Preconcentration Method Based on Dispersive Liquid–Liquid Microextraction for the Spectrophotometric Determination of Aziridine in Food Simulants

In this work a simple, rapid and sensitive method using dispersive liquid–liquid microextraction (DLLME) combined with UV–Vis spectrophotometry has been developed for the preconcentration and determination of trace amounts of aziridine in food simulants. The method is based on derivatization of aziridine with Folin's reagent (1,2-naphthoquione-4-sulphonic acid) and extraction of color product using DLLME technique. Some important parameters, such as reaction conditions, and type and volume of extraction solvent and disperser solvent were studied and optimized. Under optimum conditions, a linear calibration curve in the range of 2.0–350 ng mL^?1 of aziridine was obtained. Detection limit based on 3S_b was 1.0 ng mL^?1, and the relative standard deviation for 50 ng mL^?1 of aziridine was 2.49c (n?=?7). The proposed method was applied for the determination of aziridine in food simulants.     

Characterisation of silver release from nanoparticle-treated baby products

ABSTRACT

We tested six kinds of commercially available baby products containing nano-silver and divided them into two categories: baby food containers and baby oral care products, according to usage. We measured the total mass of silver, particle size, particle number concentration and the mobility under different simulated conditions. The total mass of silver in baby products and migration solutions was quantified by ICP-MS analysis, and the size of the migrated particles was investigated by single particle ICP-MS and transmission electron microscopy-energy dispersive spectrometer. Nano-silver has different migration behaviour in different materials, and the total mass of silver released in 3% acetic acid was generally highest for plastic material, while highest in 10% ethanol for silicone material. For baby food containers and baby oral care products, the total amount of silver in the migration solutions varied from 2.98 to 126.46 ng/dm² and from 2.01 to 2.83 ng/g, respectively. The research shows that the use of baby products containing silver may expose babies to silver nanoparticles.     

Study of silver ion migration from melt-blended and layered-deposited silver polyethylene nanocomposite into food simulants and apple juice

Colloidal silver nanoparticles were prepared via chemical reduction using polyethylene glycol (PEG) as a reducing agent, stabiliser and solvent. Silver polyethylene nanocomposites were produced via two methods, namely: melt blending and layer-by-layer (LBL) deposition of silver nanoparticles onto a polyethylene film. The silver ion release from either melt-blended or LBL-deposited nanocomposites into a food simulant and apple juice during 30 days at 4°C and 40°C was determined by atomic absorption spectroscopy. The effects of incorporating or coating of silver nanoparticles, silver concentration, contact media, temperature and time on silver ion migration were evaluated using factorial design. The diffusion coefficients of silver ions into the food simulants and apple juice were calculated using the Miltz model. The results indicated that the production method of nanocomposite, silver concentration, temperature, time and contact media showed a significant effect (p < 0.05) on silver ion migration. The quantity of silver ion migration from the nanocomposites into the food simulants and apple juice was less than the cytotoxicity-level concentration (10 mg kg^?1) in all cases over 30 days. The coating of silver nanoparticles, higher silver concentration in the nanocomposite, higher temperature and acidic property of contact liquid all promoted the silver ion release from the nanocomposite films. The migration of silver ions from nanocomposites obeyed first-order diffusion kinetics.     

Updated evaluation of the migration of styrene monomer and oligomers from polystyrene food contact materials to foods and food simulants

Due to the 2011 labelling of styrene monomer as “reasonably anticipated to be a human carcinogen” by the National Institutes of Health’s National Toxicology Program (NTP) and the controversy over whether styrene oligomers mimic the physiological effects of estrogen, an updated review of styrene monomer and oligomers in food and food contact materials (FCMs) was performed. The concentrations of styrene monomer and oligomers were determined in 24 polystyrene (PS) products and ranged from 9.3 to 3100 mg kg^–1 for the styrene monomer, 130–2900 mg kg^–1 for the sum of three styrene dimers, and 220–16,000 mg kg^–1 for the sum of six styrene trimers. Foods in contact with PS packaging had styrene monomer concentrations ranging from 2.6 to 163 ng g^–1; dimer concentrations from the limit of quantitation (LOQ) to 4.8 ng g^–1 and trimer concentrations were all below the LOQ (2 ng g^–1). Diffusion coefficients (D_p) and partition coefficients (K) were also calculated for styrene dimers and trimers. The results presented here indicate that styrene monomer concentrations in foods have not significantly changed since the 1980s and monomer concentrations in food packaging quantified in this study were all below USFDA limits. Although styrene dimers and trimers are present in higher concentrations in PS FCMs than the monomer, their migration to food is limited because of their high K values (4 × 10² to 2 × 10⁶) and their low diffusion coefficients in PS products. Additionally, diffusion coefficients calculated using USFDA-recommended food simulants and Arrhenius plots describing the temperature dependence of styrene dimers and trimers can be used in future calculations of dietary intake of the styrene oligomers.     

Temperature and pH affect copper release kinetics from copper metal foil and commercial copperware to food simulants

ABSTRACT

Copper (Cu) metal and alloys are used in cookware and other food contact surfaces due to their desirable properties for various applications. However, Cu metal can ionise and subsequently transfer to food and beverages under certain conditions. Here, we tested how pH and temperature affected Cu release kinetics using model systems utilising Cu metal foil and commercially available copperware. Cu foil and copperware were exposed to food simulants composed of 3% (w:w) aqueous solutions of citric acid, malic acid, acetic acid, or deionised (DI) water at temperatures ranging from 4°C to 60°C. An additional pilot experiment tested how simulated long-term cleaning affected subsequent Cu release from lined and unlined copperware to 3% citric acid. Food simulants were then analysed by ICP-MS for total Cu. After 180 min, incubation of Cu metal foil with acid-containing food simulants at 4°C resulted in Cu release ranging from 8.7 - 14.0 µg cm^?2, while 21.5–38.1 µg cm^?2 was released at 60°C. In contrast, Cu transfer from metal foil to DI water was relatively low, with <0.6 µg cm^?2 released after 180 min at 60°C. With citric acid food simulant, lined copperware released between 0.6 and 3.0 µg Cu cm^?2 over 180 min at the set temperatures, while unlined copperware released approximately 25–45 fold higher amounts of Cu (26.9–74.6 µg cm^?2) over this same time period. In contrast, use of DI water food simulant resulted in Cu release of <0.1 µg cm^?2 for the lined copperware and <2 µg cm^?2 for the unlined type. No significant effect of simulated long-term cleaning on Cu release from copperware was observed. These data indicate that Cu release is affected by temperature and pH, and that specific steps can be taken to limit Cu metal release from food contact surfaces to foods and beverages.     

Assessment of the migration potential of nanosilver from nanoparticle-coated low-density polyethylene food packaging into food simulants

An experimental nanosilver-coated low-density polyethylene (LDPE) food packaging was incubated with food simulants using a conventional oven and tested for migration according to European Commission Regulation No. 10/2011. The commercial LDPE films were coated using a layer-by-layer (LbL) technique and three levels of silver (Ag) precursor concentration (0.5%, 2% and 5% silver nitrate (AgNO₃), respectively) were used to attach antimicrobial Ag. The experimental migration study conditions (time, temperature and food simulant) under conventional oven heating (10 days at 60°C, 2 h at 70°C, 2 h at 60°C or 10 days at 70°C) were chosen to simulate the worst-case storage period of over 6 months. In addition, migration was quantified under microwave heating. The total Ag migrant levels in the food simulants were quantified by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Mean migration levels obtained by ICP-AES for oven heating were in the range 0.01–1.75 mg l^?1. Migration observed for microwave heating was found to be significantly higher when compared with oven heating for similar temperatures (100°C) and identical exposure times (2 min). In each of the packaging materials and food simulants tested, the presence of nanoparticles (NPs) was confirmed by scanning electron microscopy (SEM). On inspection of the migration observed under conventional oven heating, an important finding was the significant reduction in migration resulting from the increased Ag precursor concentration used to attach Ag on the LDPE LbL-coated films. This observation merits further investigation into the LbL coating process used, as it suggests potential for process modifications to reduce migration. In turn, any reduction in NP migration below regulatory limits could greatly support the antimicrobial silver nanoparticle (AgNP)-LDPE LbL-coated films being used as a food packaging material.     

Migration of copper from nanocopper/LDPE composite films

Three nanocopper/low-density polyethylene (LDPE) composite films were tested in food simulants (3% acetic acid and 10% ethanol) and real food matrices (rice vinegar, bottled water and Chinese liquor) to explore the behaviours of copper migration using ICP-OES and GFAAS. The effects of exposure time, temperature, nanocopper concentration and contact media on the release of copper from nanocopper/LDPE composite films were studied. It was shown that the migration of copper into 10% ethanol was much less than that into 3% acetic acid at the same conditions. With the increase of nanocopper concentration, exposure time and temperature, the release of copper increased. Copper migration does not appear to be significant in the case of bottled water and Chinese liquor compared with rice vinegar with a maximum value of 0.54 μg mL^?1 for the CF-0.25# bags at 70°C for 2 h. The presence and morphology of copper nanoparticles in the films and the topographical changes of the films were confirmed by field emission scanning electron microscope (FE-SEM) and atomic force microscope (AFM). In this manner, copper nanoparticles of different morphologies, sizes and distribution were found, and samples with higher nanocopper concentration had a more irregular topography. In the case of Fourier transform infrared spectroscopy (FTIR), no chemical bonds formed between copper nanoparticles and LDPE. Copper nanoparticles were just as physically dispersed in LDPE.     

Characterisation and potential migration of silver nanoparticles from commercially available polymeric food contact materials

The potential for consumer exposure to nano-components in food contact materials (FCMs) is dependent on the migration of nanomaterials into food. Therefore, characterising the physico-chemical properties and potential for migration of constituents is an important step in assessing the safety of FCMs. A number of commercially available food storage products, purchased domestically within the United States and internationally, that claim to contain nanosilver were evaluated. The products were made of polyethylene, polypropylene and polyphenylene ether sulfone and all contained silver (0.001–36 mg kg^–1 of polymer). Silver migration was measured under various conditions, including using 3% acetic acid and water as food simulants. Low concentrations (sub-ppb levels) of silver were detected in the migration studies generally following a trend characterised by a surface desorption phenomenon, where the majority of the silver migration occurred in the first of three consecutive exposures. Silver nanoparticles were not detected in food simulants, suggesting that the silver migration may be due solely to ionic silver released into solution from oxidation of the silver nanoparticle surface. The absence of detectable silver nanoparticles was consistent with expectations from a physico-chemical view point. For the products tested, current USFDA guidance for evaluating migration from FCMs was applicable.     

Release of carbon nanoparticles of different size and shape from nanocomposite poly(lactic) acid film into food simulants

ABSTRACT

Poly(lactic) acid (PLA) film with 2 wt% mixed carbon nanofillers of graphene nanoplates (GNPs) and multiwall carbon nanotubes (MWCNTs) in a weight ratio of 1:1 with impurities of fullerene and carbon black (CB) was produced by layer-to-layer deposition and hot pressing. The release of carbon nanoparticles from the film was studied at varying time–temperature conditions and simulants. Migrants in simulant solvents were examined with laser diffraction analysis and transmission electron microscopy (TEM). Film integrity and the presence of migrants on the film surfaces were visualised by scanning electron microscopy (SEM). The partial dissolution of PLA polymer in the solvents was confirmed by swelling tests and differential scanning calorimetry (DSC). Nanoparticle migrants were not detected in the simulants (at the LOD 0.020 μm of the laser diffraction analysis) after migration testing at 40°C for 10 days. However, high-temperature migration testing at 90°C for 4 h provoked a release of GNPs from the film into ethanol, acetic acid and oil-based food simulants. Short carbon nanotubes were observed rarely to release in the most aggressive acetic acid solvent. Obviously, the enhanced molecular mobility at temperatures above the glass transition and partial dissolution of PLA polymer by the food simulant facilitate the diffusion processes. Moreover, shape, size and concentration of nanoparticles play a significant role. Flexible naked GNPs (lateral size 100–1000 nm) easily migrate when the polymer molecules exhibit enhanced mobility, while fibrous MWCNTs (> 1 μm length) formed entangled networks on the film surfaces as the PLA polymer is partly dissolved, preventing their release into food simulants. The impurities of fullerenes and CB (5–30 nm) were of minor concentration in the polymer, therefore their migration is low or undetectable. The total amount of released migrants is below overall migration limits.     

Migration of perfluoroalkyl acids from food packaging to food simulants

A broad range of fluorochemicals is used to impart oil and water barrier properties to paper and paperboard food packaging. Many of the fluorochemicals are applied to paper and paperboard as complex mixtures containing reaction products and by-products and unreacted starting materials. This work primarily focussed on the determination of seven perfluorocarboxylic acids (PFCAs) in two commercially available food contact papers: a di-perfluoro-alkyloxy-amino-acid and a perfluoroalkyl phosphate surfactant. In addition, the migration of the PFCAs into five food simulants from two commercial packages was evaluated. All seven PFCAs were detected in the range of 700–2220 µg kg^?1 of paper, while three perfluoroalkyl sulphonates were under the LOD. Results from migration tests showed that migration depends on paper characteristics, time and food simulant. The percentage of migration after 10 days at 40°C ranged from 4.8% to 100% for the two papers and different food simulants.     

Antioxidants Release from Solvent-Cast PLA Film: Investigation of PLA Antioxidant-Active Packaging

The release study of natural antioxidants, i.e., ascorbyl palmitate and α-tocopherol, and synthetic phenolic antioxidants including butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), propyl gallate, and tert-butylhydroquinone (TBHQ) from polylactic acid (PLA) film into food simulants were accomplished. PLA antioxidant films were placed in contact with 95, 50, and 10 % ethanol at 40 and 20 °C. Released antioxidants were regularly measured by high-performance liquid chromatography system for 60 days. Ascorbyl palmitate was completely degraded during film preparation and is not a suitable antioxidant for PLA antioxidant-active packaging. The diffusion coefficient (D) and partition coefficient (K) of antioxidants were calculated based on obtained data. Diffusion of the antioxidants from PLA to the simulants showed a Fick’s behavior with the diffusion coefficient (D) value between 10^?9 and 10^?11 cm² s^?1 with 0–100 % of release. Faster and higher release of antioxidants occurred at 40 °C according to Arrhenius law. At 40 °C, TBHQ in 95 % ethanol decomposed to 2-tert-butyl-1,4-benzoquinone and other quinone derivatives, and α-tocopherol in 50 % ethanol decomposed to some unknown neoformed compounds. Antioxidants molecular weight, Log P, simulant polarity, and temperature were the most influencing factors on antioxidants release rate from PLA films in contact with food simulants. The D and K coefficients of studied antioxidants from PLA in three food simulants and two temperatures can be used to create PLA antioxidant-active packaging to continually control the oxidation reactions in diverse foodstuffs to ensure higher food qualities. The PLA antioxidant-active packaging approach also permits to reduce the amounts of directly added antioxidants in foods to provide safer foods.     

Development and validation of an HPLC method with fluorescence detection for the determination of fluorescent whitening agents migrating from plastic beverage cups

An HPLC method with fluorescence detection has been developed and validated for the quantification of six fluorescent whitening agents (FWA) in plastic beverage cups after extraction and in food simulants after migration at 70°C for 2 h. The sensitivity of the method was high with LODs ranging from 0.053 to 0.251 μg kg^?1 and LOQs from 0.107 to 0.504 μg kg^?1. Accuracy and precision were highly acceptable, with recoveries greater than 82% and RSDs (%) below 16%. The expanded combined uncertainty was found to be less than 23% for the measurements of all studied FWAs. In extracting the analytes from food contact materials (FCM), accelerated solvent extraction (ASE) and Soxhlet extraction were applied using ethanol as the extraction solvent. The results obtained for FWA in 10 different food plastic cups, made from different polymers, were compared. The ASE technique proved to be faster, more effective and efficient than Soxhlet extraction. Migration tests with official food simulants from Regulation (EU) No 10/2011 showed that the substances studied could potentially migrate using the selected migration conditions. The most pronounced effect was observed in case of simulant D1 (50% w/v ethanol in water). The analytical method proved to be a simple, fast, sensitive and reliable tool for the simultaneous quantification of six of the most used FWAs in both FCM extracts and food simulants after migration experiments.     

Occurrence of 13 volatile organic compounds in foods from the Canadian total diet study

Volatile organic compounds (VOCs) are ubiquitous in the environment due to evaporation and incomplete combustion of fuels, use of consumer and personal care products, etc. and they can accumulate in foods. Some VOCs in foods can also be formed during food processing and preparation and migrate from food packaging. In this pilot study, a GC-MS method based on headspace solid-phase microextraction (SPME) was validated and used to analyse selected individual foods which can be consumed directly and 153 different total diet composite food samples for 13 VOCs. Vinyl chloride was not detected in any of the 153 composite food samples, while the other 12 VOCs were detected at various frequencies, with m-xylene being the most frequently detected (in 151 of the 153 samples), followed by toluene (145), 1,3,5-trimethylbenzene (140), ethylbenzene (139), styrene (133), 1,2,4-trimethylbenzene (122), benzene (96), p-dichlorobenzene (95), n-butylbenzene (55), chloroform (45), naphthalene (45) and trichloroethylene (31). Concentrations of the 12 VOCs in most of the food composite samples were low, with the 90th percentiles from 1.6 ng g^–1 for n-butylbenzene to 20 ng g^–1 for toluene. However, some VOCs were detected at higher levels with maxima, for example, of 948 ng g^–1 for m-xylene and 320 ng g^–1 for ethylbenzene in chewing gum, 207 ng g^–1 for styrene and 157 ng g^–1 for toluene in herbs and spices. VOCs were detected at higher levels in most of the individual food items than their corresponding composite samples, for example, the average chloroform concentration in the individual canned soft drinks was 20 ng g^–1 compared with 3.0 ng g^–1 in their composite, and the average toluene concentration in the individual canned citrus juice was 96 ng g^–1 compared with 0.68 ng g^–1 in their composite. Thus, for determination of VOCs in foods which can be consumed directly, their individual food items should be analysed whenever possible for accurate exposure assessment.     

Effects of consumer use practices on nanosilver release from commercially available food contact materials

ABSTRACT

Migration evaluation involving nano-enabled food contact materials (FCMs) mostly focuses on potential nanoparticle release from new unused products. This may not represent consumer use practices encountered by the FCMs in their lifecycle. In order to determine if product use impacts the release of nanoparticles or other FCM components, it is necessary to perform migration evaluations under typical consumer use scenarios. A quantitative assessment of nanoparticle release from a commercially available nanosilver-enabled cutting board was performed under five conditions intended to simulate consumer use. Knife motion, washing and scratching scenarios were simulated by linear abrasion using knife blades, scrubbing pads and tungsten carbide burr attachments, respectively. Migration was evaluated using water and 3% acetic acid as food simulants. Low concentrations of silver (Ag) were detected in water simulants, a small portion (<4 ng dm^?2) in the form of silver nanoparticles (AgNPs) with particle number concentrations on the order of 10⁶ particles dm^?2. Median particle diameter was 40 nm. Nanoparticle release into water was observed under all five consumer use scenarios studied, however there was no correlation with the different levels of stress simulated.     

Potential silver nanoparticles migration from commercially available polymeric baby products into food simulants

In recent years, silver nanoparticles (AgNPs) have been extensively employed in food packaging systems as a potential antibacterial agent. Although proven to be highly effective, the increased number of AgNP-containing products raises concerns among consumers regarding the migration of AgNPs from the packaging material into foods, which may exert toxic effects. To address this, five baby products were chosen (baby bottle A, baby bottle B, pacifier A, pacifier B and breastmilk storage bag) to investigate AgNPs migration into three food simulants (deionised water, 4% acetic acid (w/v) and 50% ethanol (v/v)) using inductively coupled plasma mass spectrometry (ICP-MS). As a result, the highest level of migrated Ag was observed for 4% acetic acid in the case of baby bottle B, pacifier A, pacifier B and the breastmilk storage bag, with the detection amount ranging from 1.05–2.25 ng/mL. On the other hand, baby bottle A showed the maximum migration for 50% ethanol due to the polymer nature. Finally, a centrifugal ultrafiltration experiment was conducted to determine the fraction of dissolved Ag in acidic simulant and it was found that migrated Ag was predominantly in Ag⁺ form, with a small fraction of non-ionic AgNPs. Thus, it has been found that the amount of migrated Ag in baby products was low; however, the migration was dependent on the type of food simulant and polymer nature.     

Determination of Toxic Elements in Nuts by Inductively Coupled Plasma Mass Spectrometry after Microwave-Induced Combustion

Microwave-induced combustion (MIC) of nuts in closed vessels was evaluated as a sample preparation method for further determination of As, Cd, and Pb by inductively coupled plasma mass spectrometry (ICP-MS) and Hg by flow injection cold vapor generation coupled to ICP-MS (FI-CVG–ICP-MS). Conventional microwave-assisted acid digestion (MW-AD) in pressurized vessels was also used for results comparison. Samples were wrapped in polyethylene films and combusted using 20 bar of oxygen and 50 μl of 6 mol l^?1 ammonium nitrate as aid for ignition. Sample masses up to 500 mg of hazelnuts, almonds, cashew nuts, Brazil nuts, and walnuts were combusted using 7 mol l^?1 HNO₃ as absorbing solution. Accuracy was evaluated using certified reference materials and an agreement better than 96% was obtained for all analytes. Using MIC, it was possible to obtain lower limits of detection (LODs) in comparison with those obtained by MW-AD. The LOD obtained using MIC was 3, 2, and 6 ng g^?1 for As, Cd, and Pb, respectively. The LOD for Hg by FI-CVG–ICP-MS was 7 ng g^?1. Residual carbon content obtained after decomposition by MW-AD and MIC was 20% and lower than 1.5%, respectively, showing the high efficiency of MIC and allowing the determination of toxic elements in samples with high fat content. With the use of MIC up to eight samples could be processed simultaneously and only diluted nitric acid was required minimizing physical interferences, reagent consumption, and waste generation.