Migration of Ti from nano-TiO2-polyethylene composite packaging into food simulants

An analytical method based on ICP-MS was developed for the determination of Ti in food simulants (3% (w/v) aqueous acetic acid and 50% (v/v) aqueous ethanol). The method was used to determine the migration of Ti from nano-TiO₂-PE films used for food packaging into food simulants under different temperature and migration time conditions. The maximum migration amounts into 3% (w/v) aqueous acetic acid were 1.4 ± 0.02, 6.3 ± 0.5 and 12.1 ± 0.2 μg kg^?1 at 25, 70 and 100°C, respectively, while into 50% (v/v) aqueous ethanol, the maximum migration amounts were 0.5 ± 0.1, 0.6 ± 0.03 and 2.1 ± 0.1 μg kg^?1 at 25, 70 and 100°C, respectively. Increasing the additive content in the film promoted migration of nanoparticles. The results indicated that the migration of nanoparticles might occur via dissolution from the surface and cut edges of the solid phase (film) into the liquid phase (food simulant).     

Migration levels of PVC plasticisers: Effect of ionising radiation treatment

Migration levels of commercial plasticisers [di-(2-ethylhexyl) adipate (DEHA) and acetyl tributyl citrate (ATBC)] from polyvinyl chloride (PVC) film into the EU specified aqueous food simulants (distilled water, 3% w/v acetic acid and 10% v/v ethanol) were monitored as a function of time. Migration testing was carried out at 40 °C for 10 days (EEC, 1993). Determination of the analytes was performed by applying the analytical methodology based on surfactant (Triton X-114) mediated extraction prior to gas chromatographic-flame ionisation detection (GC-FID) recently proposed by our group. The study focuses on the determination of the effect of gamma radiation on plasticiser migration into the selected simulants. PVC cling film used was subjected to ionising treatment with a [⁶⁰Co] source at doses equal to 5, 15 and 25 kGy. DEHA and ATBC migration into the EU aqueous simulating solvents was limited, yielding final concentrations in the respective ranges 10–100 μg/l and 171–422 μg/l; hence, ATBC demonstrated a stronger interaction with all three simulants compared to DEHA. Migration data, with respect to ATBC, showed that the most aggressive simulant seemed to be the 10% ethanol, while in the case of DEHA the 3% aqueous acetic acid exhibited the highest extraction efficiency; distilled water demonstrated the lowest migration in both cases. With regard to PVC treatment with gamma rays, high radiation doses up to 25 kGy produced a statistically significant (p < 0.05) effect on the migration of both plasticisers.     

Migration of silver from nanosilver–polyethylene composite packaging into food simulants

An analytical method for the determination of silver in food simulants (3% (w/v) aqueous acetic acid or 95% (v/v) aqueous ethanol) was developed based on inductively coupled plasma mass spectrometry (ICP-MS). Recoveries ranged from 87% to 109% and RSDs ranged from 0.7% to 7.8%. The procedure was applied to determine the migration of silver from nanosilver–polyethylene food packaging film into food simulants at different temperatures and migration times. Results indicated that the maximum migration ratios were 1.70%, 3.00% and 5.60% for 3% (w/v) aqueous acetic acid at 20, 40 and 70°C, respectively, while for 95% (v/v) aqueous ethanol the maximum migration ratios were 0.24%, 0.23% and 0.22% at 20, 40 and 70°C.     

Migration of melamine from can coatings cross-linked with melamine-based resins,into food simulants and foods

Resins based on melamine-formaldehyde and related analogues such as methylolated melamine are used to cross-link coatings used inside food cans and on the metal closures of glass jars. Thirteen commercially coated cans and closures representing 80% of the European market were tested using simulants under realistic industrial heat-processing conditions for canned and jarred foods. The food simulants and the retort conditions used were 3% acetic acid for 1?h at 100°C and 10% ethanol for 1?h at 130°C. The highest migration level seen for melamine into simulant was 332?µg?kg^?1. There was no detectable migration of the melamine analogues cyanuric acid (<1?µg?kg^?1) or ammelide (<5?µg?kg^?1) from any sample. Twelve of the thirteen samples released no detectable ammeline (<5?µg?kg^?1) but the coating giving the highest release of melamine did also release ammeline at 8?µg?kg^?1 with the higher of the two process temperatures used. Migration experiments into food simulant and foods themselves were then conducted using two experimental coatings made using amino-based cross-linking resins. Coated metal panels were exposed to the food simulant 10% (v/v) aqueous ethanol and to three foodstuffs under a range of time and temperature conditions both in the laboratory and in a commercial food canning facility using proprietary time and temperature conditions. The highest migration into a food was 152?µg?kg^?1 from the first coating processed for a long time at a moderate sterilisation temperature. The highest migration into simulant was also from this coating at 220?µg?kg^?1 when processed at 134°C for 60?min, dropping to 190?µg?kg^?1 when processed at 123°C for 70?min. Migration from the second coating was quite uniformly two to three times lower under all tests. These migration results were significantly higher than the levels of melamine extractable using 95% ethanol at room temperature. The experiments show that commercial canning and retorting can be mimicked in an acceptable way using laboratory tests with an autoclave or a simple pressure cooker. The results overall show there is hydrolytic degradation of the melamine cross-linked resins to release additional melamine. There is a strong influence of the temperature of heat treatment applied with foods or simulants but only a minor influence of time of heating and only a minor influence, if any, of food/simulant acidity.     

Effect of sterilisation and storage conditions on the migration of bisphenol A from tinplate cans of the Lebanese market

The use of bisphenol A (BPA) in lacquer coating of food cans has been restricted by different authorities in many countries, such as in Europe. However, such regulation does not exist in many other countries including Lebanon. Due to the lack of data on the quality of Lebanese can production; this study investigates the migration of BPA from two types of tinplate cans manufactured in Lebanon, before and after sterilisation. Cans were analysed under different storage conditions (time and temperature) and filled with an aqueous simulant. The determination of BPA was carried out using UPLC with fluorescence detection, and further confirmed by MS detection. After sterilisation BPA levels drastically increased from an average of 0.15 to 109 µg/kg, giving a BPA migration around 10.5 µg/dm² for both types of cans. Storage temperature and time had no significant influence on BPA levels in sterilised cans (p-value > 0.05); however, these factors significantly affected BPA levels in non-sterilised cans.     

Assessment of the migration potential of nanosilver from nanoparticle-coated low-density polyethylene food packaging into food simulants

An experimental nanosilver-coated low-density polyethylene (LDPE) food packaging was incubated with food simulants using a conventional oven and tested for migration according to European Commission Regulation No. 10/2011. The commercial LDPE films were coated using a layer-by-layer (LbL) technique and three levels of silver (Ag) precursor concentration (0.5%, 2% and 5% silver nitrate (AgNO₃), respectively) were used to attach antimicrobial Ag. The experimental migration study conditions (time, temperature and food simulant) under conventional oven heating (10 days at 60°C, 2 h at 70°C, 2 h at 60°C or 10 days at 70°C) were chosen to simulate the worst-case storage period of over 6 months. In addition, migration was quantified under microwave heating. The total Ag migrant levels in the food simulants were quantified by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Mean migration levels obtained by ICP-AES for oven heating were in the range 0.01–1.75 mg l^?1. Migration observed for microwave heating was found to be significantly higher when compared with oven heating for similar temperatures (100°C) and identical exposure times (2 min). In each of the packaging materials and food simulants tested, the presence of nanoparticles (NPs) was confirmed by scanning electron microscopy (SEM). On inspection of the migration observed under conventional oven heating, an important finding was the significant reduction in migration resulting from the increased Ag precursor concentration used to attach Ag on the LDPE LbL-coated films. This observation merits further investigation into the LbL coating process used, as it suggests potential for process modifications to reduce migration. In turn, any reduction in NP migration below regulatory limits could greatly support the antimicrobial silver nanoparticle (AgNP)-LDPE LbL-coated films being used as a food packaging material.     

Migration of perfluoroalkyl acids from food packaging to food simulants

A broad range of fluorochemicals is used to impart oil and water barrier properties to paper and paperboard food packaging. Many of the fluorochemicals are applied to paper and paperboard as complex mixtures containing reaction products and by-products and unreacted starting materials. This work primarily focussed on the determination of seven perfluorocarboxylic acids (PFCAs) in two commercially available food contact papers: a di-perfluoro-alkyloxy-amino-acid and a perfluoroalkyl phosphate surfactant. In addition, the migration of the PFCAs into five food simulants from two commercial packages was evaluated. All seven PFCAs were detected in the range of 700–2220 µg kg^?1 of paper, while three perfluoroalkyl sulphonates were under the LOD. Results from migration tests showed that migration depends on paper characteristics, time and food simulant. The percentage of migration after 10 days at 40°C ranged from 4.8% to 100% for the two papers and different food simulants.     

Migration of photoinitiators from paper to fatty food simulants: experimental studies and model application

The migration of five different photoinitiators from kraft paper to two fatty food simulants, Tenax^® and 95% ethanol, was investigated under different conditions. The effects of temperature and storage time, as well as the physicochemical properties of the photoinitiators on migration, were discussed. Mathematical models based on Fick’s second law generated from two cases, single- and two-side contacts, were applied to predict the migration behaviour from the paper to the food simulants. The partition coefficients estimated from the model decreased with temperature. The diffusion coefficients of the selected photoinitiators from the paper ranged from 1.55 × 10^–10 to 7.54 × 10^–9 cm² s^?1 for Tenax and from 2.79 × 10^–9 to 8.03 × 10^–8 cm² s^?1 for 95% ethanol. The results indicate that the applied model can predict the migration of photoinitiators in the initial short period before equilibrium, and the migration from paper to Tenax through a single-side contact demonstrated an especially high concordance.     

Migration study of caprolactam from polyamide 6 sheets into food simulants

Caprolactam, used in manufacturing polyamide (PA) 6, may threaten human health. Here, PA 6 sheets were produced by using a twin-screw extruder to evaluate its safety. Caprolactam migration concentrations from the PA 6 sheets into food simulants were evaluated according to the standard migration test conditions under the Korean Food Standards Codex (KFSC). Concentrations were investigated under various food simulants (distilled water, 4% acetic acid, 20 and 50% ethanol, and heptane) and storage conditions (at 25, 60, and 95 °C). Caprolactam migration concentrations into food simulants were determined as follows: 4% acetic acid (0.982 mg/L), distilled water (0.851 mg/L), 50% ethanol (0.624 mg/L), 20% ethanol (0.328 mg/L), and n-heptane (not detected). Migrations were determined to be under the regulatory concentration (15 mg/L) according to the KFSC test conditions. Taken together, these results verified that the standard migration test conditions by KFSC were reliable to evaluate the safety of PA 6.     

Development and validation of an HPLC method with fluorescence detection for the determination of fluorescent whitening agents migrating from plastic beverage cups

An HPLC method with fluorescence detection has been developed and validated for the quantification of six fluorescent whitening agents (FWA) in plastic beverage cups after extraction and in food simulants after migration at 70°C for 2 h. The sensitivity of the method was high with LODs ranging from 0.053 to 0.251 μg kg^?1 and LOQs from 0.107 to 0.504 μg kg^?1. Accuracy and precision were highly acceptable, with recoveries greater than 82% and RSDs (%) below 16%. The expanded combined uncertainty was found to be less than 23% for the measurements of all studied FWAs. In extracting the analytes from food contact materials (FCM), accelerated solvent extraction (ASE) and Soxhlet extraction were applied using ethanol as the extraction solvent. The results obtained for FWA in 10 different food plastic cups, made from different polymers, were compared. The ASE technique proved to be faster, more effective and efficient than Soxhlet extraction. Migration tests with official food simulants from Regulation (EU) No 10/2011 showed that the substances studied could potentially migrate using the selected migration conditions. The most pronounced effect was observed in case of simulant D1 (50% w/v ethanol in water). The analytical method proved to be a simple, fast, sensitive and reliable tool for the simultaneous quantification of six of the most used FWAs in both FCM extracts and food simulants after migration experiments.     

Nanoclay migration from food packaging materials

A recent trend is to use nanocomposites materials for food-packaging applications. Different kinds of nanoparticles are incorporated into the polymers to improve their characteristics, and, among them, nanoclay is used to improve their barrier properties to gases. In this work, the results of migration studies with different food simulants (ethanol 10% and acetic acid 3%), temperatures and times (40ºC for 10 days and 70ºC for 2 h) from two commercialised LDPE nanocomposite bags are presented. The migration solutions thus obtained were analysed by ICP-MS to evaluate the amount of aluminium which migrated into the solutions both in dissolved form and as a part of nanoparticles. Aluminium migration was observed for both samples with a maximum migration value of 51.65 ng cm^–2 for the Aisaika bags and 24.14 ng cm^–2 for the Debbie Meyer bags. The presence of spikes working in single-particle mode using ICP-MS indicated that part of this aluminium was present as nanoparticles. The size and morphology of the nanoclay, in both the original material and the migration solutions, was studied by scanning electron microscopy coupled to energy-dispersive X-ray diffraction (SEM-EDX). In this manner, nanoparticles of different morphologies and sizes were found to migrate into the food simulants.     

紫外分光光度法测定食品模拟物中六价铬和铝

建立食品模拟物中铝和六价铬的紫外分光光度测定方法。用含内涂层的金属饮料罐(两片罐和三片罐)分别盛装水、3%乙酸水溶液、10%乙醇水溶液,于40℃浸泡240h,得到食品模拟物。水、3%乙酸水溶液食品模拟物样品直接测定,10%乙醇水溶液食品模拟物经蒸发乙醇再测定。采用二苯碳酰二肼分光光度法测定六价铬,铬天青S分光光度法测定铝。六价铬的方法检出限为10ng/mL,方法回收率在82.0%～101%;铝的方法检出限为25ng/mL,回收率在82.2%～108%。该方法准确度高,操作简单。     

Migration of epoxidised soybean oil from PVC gaskets of commercial lids: simulation of migration under various conditions and screening of food products from Czech markets

Previous studies have shown that a large number of polyvinylchloride (PVC) lid gaskets exceed the existing migration limits for epoxidised soybean oil (ESBO) and correct prediction of ESBO release into food therefore appears to be a difficult issue. ESBO migration from PVC gaskets of metal closures into food simulants and food products from the Czech market is evaluated during a survey in 2009 and subsequently one in 2012 to assess progress in lid manufacturing and official testing conditions. ESBO migration from lids into various food simulants was studied at various temperatures (25, 40 and 60°C) during storage times up to 12 months. ESBO released into food simulants or food products was transmethylated, derivatised and analysed by GC-MS. The levels of ESBO migration in foodstuffs in 2012 exceeded the specific migration limit (SML) in fewer products in comparison with the previous survey. However, most of the products were analysed at a time far from the expiry date and exceedance of the SML at the end of the product shelf life is not therefore excluded. More severe test conditions (60°C for 10 days) for specific migration given by the current European Union legislation (Regulation (EU) No. 10/2011) still seem to be insufficient for the simulation of ESBO migration during long-term storage.     

发泡餐盒中苯乙烯单体和低聚物的测定及迁移风险评估

目的建立聚苯乙烯发泡餐盒中苯乙烯单体和低聚物的检测方法,并对其向食品的迁移进行风险评估。方法采用二氯甲烷溶解-甲醇沉淀法提取餐盒中的苯乙烯单体和低聚物,采用气相色谱-质谱联用法测定目标物向水、酒精和脂肪食品模拟物的迁移量,通过比较各物质的估计日摄入量和毒理学安全阈值评估迁移风险。结果苯乙烯单体和低聚物在0.02~1.00 μg/mL范围内线性良好（R均大于0.99）,在餐盒及食品模拟物中的加标回收率为80.5%~101.2%,相对标准偏差为1.6%~10.5%;在5%显著性水平下各物质向脂肪食品模拟物的迁移量明显大于向水和酒精食品模拟物的迁移量 ,扩散系数为1.3×10-15~1.4×10-9 cm2/s,迁移活化能为33.5~53.3 kJ/mol;目标分析物的估计日摄入量均未超过毒理学关注阈值。结论该方法简单、可靠, 可用于测定发泡餐盒中苯乙烯单体和低聚物的含量。聚苯乙烯发泡餐盒不适合在高温条件下盛放脂肪食品。     

Migration of silver from nanosilver-polyethylene composite packaging into food simulants

An analytical method for the determination of silver in food simulants (3% (w/v) aqueous acetic acid or 95% (v/v) aqueous ethanol) was developed based on inductively coupled plasma mass spectrometry (ICP-MS). Recoveries ranged from 87% to 109% and RSDs ranged from 0.7% to 7.8%. The procedure was applied to determine the migration of silver from nanosilver-polyethylene food packaging film into food simulants at different temperatures and migration times. Results indicated that the maximum migration ratios were 1.70%, 3.00% and 5.60% for 3% (w/v) aqueous acetic acid at 20, 40 and 70 °C, respectively, while for 95% (v/v) aqueous ethanol the maximum migration ratios were 0.24%, 0.23% and 0.22% at 20, 40 and 70 °C.     

Evaluating the migration of ingredients from active packaging and development of dedicated methods: a study of two iron-based oxygen absorbers

The behaviour of two commercial oxygen-scavenging products with respect to migration of active ingredients into foodstuffs was investigated. Migrants were identified, and by using appropriate analytical methods, migration was determined in a variety of liquid, solid or gelled food simulants and foods. Simulants were chosen to cover a range of water activities and viscosities. Foods and the gelled food simulant agar were packed with and without vacuum, and with the oxygen scavenger in various locations relative to the packed food. The main migrants, as identified by X-ray fluorescence spectrometry, infrared spectroscopy and scanning electron microscopy with energy-dispersive spectrometry were Na + and Cl - in non-acidic aqueous simulants, and Na + , Cl - and Fe 2+ in 3% acetic acid. Migration into aqueous simulants exceeded the current European Union limit for total migration from plastic materials (assumed to be currently applicable to these systems) and was probably excessive by any reasonable standard. However, neither oxygen scavenger appeared to release significant quantities of migrants into solid foods when the scavenger was properly located in the package and the packing process does not favour the contents becoming wet by water released from the food.     

Testing the influence of various conditions on the migration of epoxidised soybean oil from polyvinylchloride gaskets

Epoxidised soybean oil (ESBO) is widely used as a plasticiser and stabiliser mainly in food contact materials on the base of polyvinylchloride (PVC), especially in the gaskets of jar lids. PVC gaskets containing 10–37% of ESBO were prepared by the baking of PVC plastisols at various process temperatures (180–240°C) in the laboratory. ESBO migration into olive oil and 3% acetic acid was studied at various temperatures (4°C, 25°C, 40°C and 60°C) during a storage time up to 12 months. ESBO released into food simulants was transmethylated, derivatised and analysed by gas chromatography-mass spectrometry (GC/MS). The effect of food processing, i.e. pasteurisation (80°C and 100°C) and sterilisation (125°C) on ESBO migration was also evaluated. The results were critically assessed with respect to the test conditions of specific migration in accordance with the current European Union legislation (Regulation (EU) No. 10/2011). The levels of ESBO migration found confirmed that the test conditions (i.e. 40°C or 60°C, 10 days) representing contact in the worst foreseeable use scenario seem to be insufficient for the simulation of ESBO migration during long-term storage and thus do not provide satisfactory objective results.     

Influence of aqueous food simulants on potential nanoparticle detection in migration studies involving nanoenabled food-contact substances

Research focused on assessing potential consumer exposure to nanoparticles released from nano-enabled food-contact materials (FCMs) has often reached conflicting conclusions regarding the detection of migrating nanoparticles. These conflicting conclusions, coupled with the potential for nanoparticles to be unstable in certain food simulants, has necessitated a closer look at the role played by food simulants recommended for use in nanoparticle migration evaluation. The influence of aqueous food simulants on nanoparticles under migration evaluation conditions is reported herein. The stability of silver nanoparticles (AgNP) spiked into three food simulants (water, 10% ethanol and 3% acetic acid) was investigated using asymmetric flow field-flow fractionation (AF4), ultrafiltration, electron microscopy (EM), and single-particle inductively coupled plasma mass spectrometry (sp-ICP-MS). While 3% acetic acid induced significant oxidative dissolution of AgNP to silver ions, there were very minor to no changes in the physicochemical properties of AgNP in water and 10% ethanol.     

食品金属罐中14种双酚类物质迁移量的同时测定及杀菌过程对其迁移的影响

为了调查国内食品金属罐中双酚类物质的迁移水平,本文建立了同时测定食品金属罐中14种双酚类物质迁移量的高效液相色谱法,并研究了杀菌过程对双酚类物质迁移的影响及食品金属罐中双酚类物质的迁移规律.结果表明,14种双酚类物质在4种食品模拟物(4％体积乙酸、10％体积乙醇、50％体积乙醇和异辛烷)中线性关系良好,加标回收率为83...     

Characterisation and potential migration of silver nanoparticles from commercially available polymeric food contact materials

The potential for consumer exposure to nano-components in food contact materials (FCMs) is dependent on the migration of nanomaterials into food. Therefore, characterising the physico-chemical properties and potential for migration of constituents is an important step in assessing the safety of FCMs. A number of commercially available food storage products, purchased domestically within the United States and internationally, that claim to contain nanosilver were evaluated. The products were made of polyethylene, polypropylene and polyphenylene ether sulfone and all contained silver (0.001–36 mg kg^–1 of polymer). Silver migration was measured under various conditions, including using 3% acetic acid and water as food simulants. Low concentrations (sub-ppb levels) of silver were detected in the migration studies generally following a trend characterised by a surface desorption phenomenon, where the majority of the silver migration occurred in the first of three consecutive exposures. Silver nanoparticles were not detected in food simulants, suggesting that the silver migration may be due solely to ionic silver released into solution from oxidation of the silver nanoparticle surface. The absence of detectable silver nanoparticles was consistent with expectations from a physico-chemical view point. For the products tested, current USFDA guidance for evaluating migration from FCMs was applicable.