Effects of surface area on electrochemical performance of Li[Ni<Subscript>0.2</Subscript>Li<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>]O<Subscript>2</Subscript> cathode material

The effect of surface area on the electrochemical properties and thermal stability of Li[Ni_0.2Li_0.2Mn_0.6]O₂ powders was characterized using a charge/discharge cycler and DSC (Differential Scanning Calorimeter). The surface area of the samples was successfully controlled from ~4.0 to ~11.7 m² g⁻¹ by changing the molar ratio of the nitrate/acetate sources and adding an organic solvent such as acetic acid or glucose. The discharge capacity and rate capability was almost linearly increased with increase in surface area of the sample powder. A sample with a large surface area of 9.6–11.7 m² g⁻¹ delivered a high discharge capacity of ~250 mAh g⁻¹ at a 0.2 C rate and maintained 62–63% of its capacity at a 6 C rate versus a 0.2 C rate. According to the DSC analysis, heat generation by thermal reaction between the charged electrode and electrolyte was not critically dependent on the surface area. Instead, it was closely related to the type of organic solvent employed in the fabrication process of the powder.     

Study of electrochemical properties and the charge/discharge mechanism for Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>/MnO<Subscript>2</Subscript>-AC hybrid supercapacitor

Spinel Li₄Mn₅O₁₂ was prepared by a sol–gel method. The manganese oxide and activated carbon composite (MnO₂-AC) were prepared by a method in which KMnO₄ was reduced by activated carbon (AC). The products were characterized by XRD and FTIR. The hybrid supercapacitor was fabricated with Li₄Mn₅O₁₂ and MnO₂-AC, which were used as materials of the two electrodes. The pseudocapacitance performance of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor was studied in various aqueous electrolytes. Electrochemical properties of the Li₄Mn₅O₁₂/MnO₂-AC hybrid supercapacitor were studied by using cyclic voltammetry, electrochemical impedance measurement, and galvanostatic charge/discharge tests. The results show that the hybrid supercapacitor has electrochemical capacitance performance. The charge/discharge test showed that the specific capacitance of 51.3 F g⁻¹ was obtained within potential range of 0–1.3 V at a charge/discharge current density of 100 mA g⁻¹ in 1 mol L⁻¹ Li₂SO₄ solution. The charge/discharge mechanism of Li₄Mn₅O₁₂ and MnO₂-AC was discussed.     

Photoelectrochemical characterization of the synthetic crednerite CuMnO<Subscript>2</Subscript>

High quality crednerite CuMnO₂ was prepared by solid state reaction at 950 °C under argon flow. The oxide crystallizes in a monoclinically distorted delafossite structure associated to the static Jahn–Teller (J–T) effect of Mn³⁺ ion. Thermal analysis showed that it converts reversibly to spinel Cu _x Mn_3−x O₄ at ~420 °C in air and further heating reform the crednerite above 940 °C. CuMnO₂ is p-type, narrow semiconductor band gap with a direct optical gap of 1.31 eV. It exhibits a long-term chemical stability in basic medium (KOH 0.5 M), the semi logarithmic plot gave an exchange current density of 0.2 μA cm⁻² and a corrosion potential of ~−0.1 V_SCE. The electrochemical oxygen insertion/desinsertion is evidenced from the intensity–potential characteristics. The flat band potential (V _fb = −0.26 V_SCE) and the holes density (N _A  = 5.12 × 10¹⁸ cm⁻³) were determined, respectively, by extrapolating the curve C ⁻² versus the potential to the intersection with C ⁻²  = 0 and from the slope of the Mott–Schottky plot. From photoelectrochemical measurements, the valence band formed from Cu-3d wave function is positioned at 5.24 ± 0.02 eV below vacuum. The Nyquist representation shows straight line in the high frequency range with an angle of 65° ascribed to Warburg impedance originating from oxygen intercalation and compatible with a system under mass transfer control. The electrochemical junction is modeled by an equivalent electrical circuit thanks to the Randles model.     

Comparative study of the preparation and electrochemical performance of LiNi<Subscript>1</Subscript><Subscript>/2</Subscript>Mn<Subscript>1/2</Subscript>O<Subscript>2</Subscript> electrode material for rechargeable lithium batteries

Positive electrode material LiNi_1/2Mn_1/2O₂ was synthesized via the carbonate co-precipitation method and the hydroxide precipitation route to study the effects of the precursor on its structural and electrochemical properties. The results of X-ray diffraction and Rietveld refinement show that the carbonate precursor of Ni²⁺ and Mn²⁺ exhibits one phase at a pH of 8.5, while the hydroxide deposit separates into Ni(OH)₂ and Mn(OH)₂ phases under the same experimental conditions. LiNi_1/2Mn_1/2O₂ material prepared from the hydroxide precursor shows 8.9% Li/Ni exchange and a large capacity loss of 11.3% in the first 10 cycles. By contrast, more uniform distribution of transition metal ions and stable Mn²⁺ in the carbonate precursor contribute to only 7.8% Li/Ni disorder in the obtained LiNi_1/2Mn_1/2O₂, which delivers a reversible capacity of about 182 mAh g⁻¹ at a current rate of 14 mA g⁻¹ between 2.5 and 4.8 V.     

Synthesis and characterization of 5?V LiCoxNiyMn2?x?yO4 (x?=?y?=?0.25) cathode materials for use in rechargeable lithium batteries

Double doped spinel LiCo _x Ni _y Mn_2−x−y O₄ (x = y = 0.25) have been synthesised via sol–gel method using different chelating agents viz., acetic acid, maleic acid and oxalic acid to obtain 5 V positive electrode material for use in lithium rechargeable batteries. The sol–gel route endows lower processing temperature, lesser synthesis time, high purity, better homogeneity, good control of particle size and surface morphology. Physical characterizations of the synthesized powder were carried out using thermo-gravimetric and differential thermal analysis (TG/DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The electrochemical behaviour of the calcined samples has been carried out by galvanostatic charge/discharge cycling studies in the voltage range 3–5 V. The XRD patterns reveal crystalline single-phase spinel product. SEM photographs indicate micron sized particles with good agglomeration. The charge–discharge studies show LiCo_0.25Ni_0.25Mn_1.5O₄ synthesized using oxalic acid to be as a promising cathode material as compared to other two chelating agents and delivers average discharge capacity of 110 mA h g⁻¹ with low capacity fade of 0.2 mA h g⁻¹ per cycle over the investigated 15 cycles.     

Enhanced electrochemical performance of FeS<Subscript>2</Subscript> synthesized by hydrothermal method for lithium ion batteries

Iron disulfide (FeS₂) powders were successfully synthesized by hydrothermal method. Cetyltrimethylammonium bromide (CTAB) had a great influence on the morphology, particle size, and electrochemical performance of the FeS₂ powders. The as-synthesized FeS₂ particles with CTAB had diameters of 2–4 μm and showed a sphere-like structure with sawtooth, while the counterpart prepared without CTAB exhibited irregular morphology with diameters in the range of 0.1–0.4 μm. As anode materials for Li-ion batteries, their electrochemical performances were investigated by galvanostatic charge–discharge test and electrochemical impedance spectrum. The FeS₂ powder synthesized with CTAB can sustain 459 and 413 mAh g⁻¹ at 89 and 445 mA g⁻¹ after 35 cycles, respectively, much higher than those prepared without CTAB (411 and 316 mAh g⁻¹). The enhanced rate capability and cycling stability were attributed to the less-hindered surface layer and better electrical contact from the sawtooth-like surface and micro-sized sphere morphology, which led to enhanced process kinetics.     

Electrochemical properties of microwave-assisted reflux-synthesized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles in different electrolytes for supercapacitor applications

The nanosized Mn₃O₄ particles were prepared by microwave-assisted reflux synthesis method. The prepared sample was characterized using various techniques such as X-ray diffraction (XRD), Fourier transform-infrared spectroscopy (FT-IR), Raman analysis, and transmission electron microscopy (TEM). Electrochemical properties of Mn₃O₄ nanoparticles were investigated using cyclic voltammogram (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge–discharge analysis in different electrolytes such as 1 M KCl, 1 M Na₂SO₄, 1 M NaNO₃, and 6 M KOH electrolytes. XRD pattern reveals the formation of single-phase Mn₃O₄ nanoparticles. The FT-IR and Raman analysis also assert the formation of Mn₃O₄ nanoparticles. The TEM image shows the spherical shape particles with less than 50 nm sizes. Among all the electrolytes, the Mn₃O₄ nanoparticles possess maximum specific capacitance of 94 F g⁻¹ in 6 M KOH electrolyte calculated from CV. The order of capacitance obtained by various electrolytes is 6 M KOH > 1 M KCl > 1 M NaNO₃ > 1 M Na₂SO₄. The EIS and galvanostatic charge–discharge results further substantiate with the CV results. The cycling stability of Mn₃O₄ electrode reveals that the prepared Mn₃O₄ nanoparticles are a suitable electrode material for supercapacitor application.     

Determination of hydrogenation ability and exchange current of H<Subscript>2</Subscript>O/H<Subscript>2</Subscript> system on hydrogen-absorbing metal alloys

A detailed analysis of potential versus time measurements at galvanostatic charge/discharge conditions (external current change from −1 to +1 mA cm⁻²) for two La–Ni alloys in Ar-saturated 0.1 M KOH solution is presented. It is shown that passivation of the electrodes does not affect the potential jump as a result of current switching over. The value of potential jump allows to calculate the exchange current density for H₂O/H₂ system on the tested material. Anodic potential of the hydrogenated electrode (at i _a = const) linearly increases with logarithm of time which allows to evaluate precisely time necessary for oxidation of hydrogen absorbed during cathodic charging. The method described enables to determine effectiveness of hydrogen absorption by materials applied for negative electrodes of NiMH batteries.     

Direct-hydrothermal synthesis of LiFe<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>PO<Subscript>4</Subscript> cathode materials

Carbon free LiFe_1−x Mn _x PO₄ (x = 0, 0.05, 0.1, 0.2, 0.4) cathode materials were prepared by a direct-hydrothermal process at 170 °C for 10 h. The structural and electrochemical properties of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), charge–discharge experiments, cyclic voltammetry (CV) and alternating current (AC) impedance spectroscopy. The electrochemical performance of LiFePO₄ prepared in this manner showed to be positively affected by Mn²⁺-substitution. Among the Mn²⁺-substitution samples, the LiFe_0.9Mn_0.1PO₄ exhibited an initial discharge capacity of 141.4 mA h g⁻¹ at 0.1 C, and the capacity fading is only 2.7% after 50 cycles.     

Thermoelectric Properties of <Emphasis Type="Italic">x</Emphasis>PbTe/Yb<Subscript>0.2</Subscript>Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Hot-Pressed Samples

The xPbTe/Yb_0.2Co₄Sb₁₂ compounds were prepared by the ball-milling and hot-pressed process. Electrical conductivity of the composite samples are reduced with a increase in PbTe content; and, their temperature dependence coefficients show the positive values. The maximum electrical conductivity of composite materials is ~80000 Sm⁻¹ at 800 K. The Seebeck coefficient (absolute value) of the composite material is obviously improved with an increase in the dispersed phase (PbTe) content; the Seebeck coefficient (absolute value) of the 10PbTe sample is ~260 μVK⁻¹ at 700 K, which increases by 13.6% relative to that of the Yb_0.2Co₄Sb₁₂ sample. The thermal conductivity of the composite samples is improved due to introduction of PbTe, and the thermal conductivity of the 10PbTe sample is ~3 Wm⁻¹ K⁻¹ at 550 K. The maximum value of ZT is 0.78 at 700 K for the 2.5PbTe sample.     

A new class of Sol–gel derived LiM1xM2yMn2?x?yO3.8F0.2 (M1?=?Cr, M2?=?V; x?=?y?=?0.2) cathodes for lithium batteries

A series of LiM_1xM_2yMn_2−x−yO_3.8F_0.2 (M₁ = Cr, M₂ = V; x = y = 0.2) cathodes, viz., LiMn₂O_3.8F_0.2, LiCr_0.2Mn_1.8O_3.8F_0.2 and LiCr_0.2V_0.2Mn_1.6O_3.8F_0.2 along with native LiMn₂O₄ have been synthesized by Citric Acid assisted Modified (CAM) sol–gel method, with a view to understand the effect of synthesis methodology and the effect of dual category dopants, viz., anion and/or cation upon spinel cathodes individually. An acceptable capacity retention (94%) observed up to 50 cycles for native LiMn₂O₄ cathodes is attributed to the significance of CAM sol–gel method. Similarly, the encouraging charge–discharge results of LiMn₂O_3.8F_0.2 (130 mAh g⁻¹) and LiCr_0.2Mn_1.8O_3.8F_0.2 (142 mAh g⁻¹) cathodes revealed a possible augmentation in the reversible capacity behavior of the spinels upon F⁻ substitution at 32e site and the simultaneous substitution of Cr³⁺ and F⁻ at 16d and 32e sites respectively.     

Oxygen permeability and structural stability of La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>Co<Subscript>0.2</Subscript>Fe<Subscript>0.8</Subscript>O<Subscript>3−<Emphasis Type="Italic">δ</Emphasis></Subscript> membrane

La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ oxides were synthesized by citrate method and hydrothermal method. The oxides prepared by citrate method are perovskite type structure, while the oxides by hydrothermal method have a small amount of secondary phase in the powder. Pyrex glass seal and Ag melting seal provided reliable gas-tight sealing of disk type dense membrane in the range of operation temperature, but commercial ceramic binder could not be removed from the support tube without damage to the tube or membrane. Though the degree of gas tightness increases in the order of glass>Ag>ceramic binder, in the case of glass seal, the undesired spreading of glass leads to an interfacial reaction between it and the membrane and reduction of effective permeation area. The oxygen flux of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ membrane increases with increasing temperature and decreasing thickness, and the oxygen permeation flux through 1.0 mm membrane exposed to flowing air (P _h =0.21 atm) and helium (P₁=0.037 atm) is ca. 0.33 ml/cm²·min at 950 °C. X-ray diffraction analysis for the membrane after permeation test over 160 h revealed that La₂O₃ and unknown compound were formed on the surface of membrane. The segregation compounds of surface elements formed on both surfaces of membrane irrespective of spreading of glass sealing material. This paper was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

DSA electrochemical treatment of olive mill wastewater on Ti/RuO<Subscript>2</Subscript> anode

The electrochemical oxidation of olive mill wastewater (OMW) over a Ti/RuO₂ anode was studied by means of cyclic voltammetry and bulk electrolysis and compared with previous results over a Ti/IrO₂ anode. Experiments were conducted at 300–1,220 mg L⁻¹ initial chemical oxygen demand (COD) concentrations, 0.05–1.35 V versus SHE and 1.39–1.48 V versus SHE potential windows, 15–50 mA cm⁻² current densities, 0–20 mM NaCl, Na₂SO₄, or FeCl₃ concentrations, 80 °C temperature, and acidic conditions. Partial and total oxidation reactions occur with the overall rate being near first-order kinetics with respect to COD. Oxidation at 28 Ah L⁻¹ and 50 mA cm⁻² leads to quite high color and phenols removal (86 and 84%, respectively), elimination of ecotoxicity, and a satisfactory COD and total organic carbon reduction (52 and 38%, respectively). Similar performance can be achieved at the same charge (28 Ah L⁻¹) using lower current densities (15 mA cm⁻²) but in the presence of various salts. For example, COD removal is less than 7% at 28 Ah L⁻¹ in a salt-free sample, while addition of 20 mM NaCl results in 54% COD reduction. Decolorization of OMW using Ti/RuO₂ anode seems to be independent of the presence of salts in contrast with Ti/IrO₂ where addition of NaCl has a beneficial effect on decolorization.     

Design of Efficient Ce<Subscript>x</Subscript>M<Subscript>1−x</Subscript>O<Subscript>2−δ</Subscript> (M = Zr,Hf, Tb and Pr) Nanosized Model Solid Solutions for CO Oxidation

Abstract  

Nanosized Ce_xM_1−xO_2−δ (M = Zr, Hf, Tb and Pr) solid solutions were prepared by a modified coprecipitation method and thermally treated at different temperatures from 773 to 1073 K in order to ascertain the thermal behavior. The structural and textural properties of the synthesized samples were investigated by means of X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), BET surface area, X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy (RS) techniques. The catalytic efficiency has been performed towards oxygen storage/release capacity (OSC) and CO oxidation activity. The characterization results indicated that the obtained solid solutions exhibit defective cubic fluorite structure. The solid solutions of ceria–hafnia, ceria–terbia and ceria–praseodymium exhibited good thermal stability up to 1073 K. A new Ce_0.6Zr_0.4O₂ phase along with Ce_0.75Zr_0.25O₂ was observed in the case of ceria–zirconia solid solution due to more Zr⁴⁺ incorporation in the ceria lattice at higher calcination temperatures. The reducibility of ceria has been increased upon doping with Zr⁴⁺, Hf⁴⁺, Tb^3+/4+ and Pr^3+/4+ cations. This enhancement is more in case of Hf⁴⁺ doped ceria. Among various solid solutions investigated, the ceria–hafnia combination exhibited better OSC and CO oxidation activity. The high efficiency of Ce–Hf solid solution was correlated with its superior bulk oxygen mobility and other physicochemical characteristics.     

Determination of cadmium (II) using H<Subscript>2</Subscript>O<Subscript>2</Subscript>-oxidized activated carbon modified electrode

Pristine activated carbon (AcC) was oxidized by H₂O₂ under ultrasonic conditions. Compared with pristine AcC, the H₂O₂-oxidized AC possesses higher accumulation ability to trace levels of Cd²⁺. Based on this, a highly sensitive, simple and rapid electrochemical method was developed for the determination of Cd²⁺. In 0.01 mol L⁻¹ HClO₄ solution, Cd²⁺ was effectively accumulated at the surface of H₂O₂-oxidized AcC modified paste electrode, and then reduced to Cd under −1.10 V. During the following potential sweep from −1.10 to −0.50 V, reduced Cd was oxidized and a sensitive stripping peak appears at −0.77 V. The stripping peak current of Cd²⁺ changes linearly with concentration over the range 5.0 × 10⁻⁸ to 5.0 × 10⁻⁶ mol L⁻¹. The limit of detection was found to be 3.0 × 10⁻⁸ mol L⁻¹ for 2-min accumulation. Finally, this new sensing method was successfully used to detect Cd²⁺ in waste water samples.     

Electrochemical Properties of a 4.7 V-Class LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> Positive Electrode Material for High Power Li-Ion Battery

The LiNi_0.5Mn_1.5O₄ cathode material for high power lithium-ion battery is successfully synthesized by sol–gel method. The structure, the morphology and the electrochemical characteristics of the compound are studied by X-ray diffraction (XRD), a field emission scanning electron microscope (FE-SEM), cyclic voltammogram (CV) and charge–discharge techniques, respectively. The results indicate that LiNi_0.5Mn_1.5O₄ sample has cubic spinel structure and its particles crystallized well with submicro size. There are a higher voltage plateau around 4.7 V and a lower voltage plateau above 4 V at 3.3–5.0 V in the charge–discharge curves of LiNi_0.5Mn_1.5O₄, corresponding to two redox peaks of Ni²⁺/Ni⁴⁺ and Mn³⁺/Mn⁴⁺ of its CV respectively. The LiNi_0.5Mn_1.5O₄ with ordered Fd3m space group has 150.57 mAh g⁻¹ initial charge capacity and 139.57 mAh g⁻¹ initial discharge capacity, showing excellent electrochemical performance. A short arc at more high frequency zone from 4.4 V potential emerges in electrochemical impedance spectroscopy (EIS), attributing to oxidative decomposition of the electrolyte at high voltage. The equivalent circuit selected could fit the EIS experiment data very well.     

A Simple and Facile Preparation of LiFePO<Subscript>4</Subscript> by a One-step Microwave Hydrothermal Method

A novel method was used to synthesize LiFePO₄, using inorganic salts as raw materials, and PEG-4000 as the surfactant. The results show that LiFePO₄ powders with various morphologies were prepared by microwave hydrothermal method, and it is very important to synthesize the LiFePO₄ powders with well-defined shape and size controlling experimental conditions, such as the solution pH and surfactant. The modified preparation of LiFePO₄ was built. The coating carbon on LiFePO₄ powders as a core–shell structure was carried out by annealing in 3%H₂/97%N₂ at 700 °C for 2 h. As a result, the diffusion coefficient of lithium ions can be increased, and the reversibility of lithium intercalation and deintercalation can be improved markedly. In addition, LiMn_0.08Fe_0.92PO₄ powders were synthesized, which were observed in an ordered olivine structure, but great changes occurred in morphology. Doping Mn²⁺ does not destroy the lattice structure and enlarges the lattice volume. Consequently, the conductivity can be enhanced, and the lithium ion diffusion coefficient can be boosted. Initial discharge capacity is improved obviously, and increases to 99.6 mA h g⁻¹ and 93.8 mA h g⁻¹ respectively. The microwave assisted hydrothermal approach presented here opens a potential avenue to explore the synthesis of LiFePO₄ powders.     

Improved electrochemical properties of Li(Ni<Subscript>0.7</Subscript>Co<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode for lithium ion batteries with controlled sintering conditions

Improved electrochemical properties of Li(Ni_0.7Co_0.3)O₂ cathode material are reported. Samples were synthesized by the co-precipitation method with various sintering conditions, namely temperature, time and atmosphere. Li(Ni_0.7Co_0.3)O₂ sintered at 850 °C for 14 h in air exhibited the lowest unit cell volume accompanied with relatively higher values of c/a and I ₁₀₃/I ₁₀₄ reflection peaks ratios. This also exhibited superior electrochemical properties, such as high charge–discharge capacity, high Coulombic efficiency, and low irreversible capacity loss. This can be attributed to improved hexagonal ordering, crystallinity and morphology. The electrochemical cell parameters were better than the reported ones, probably due to controlled sintering conditions.     

Synthesis of Ni(OH)<Subscript>2</Subscript> nanostructures by the hydrothermal treatment in the presence of guanidine carbonate and their electrochemical properties

Nanostructure control of β-Ni(OH)₂ was attempted by adopting hydrothermal treatment for the high specific surface area (high-SSA) β-Ni(OH)₂ in the presence of guanidine carbonate. β-Ni(OH)₂ nanosheets-linked structures could be synthesized from high-SSA β-Ni(OH)₂ owing to the strong effects of guanidine carbonate for keeping or enlarging SSA during hydrothermal treatment. The discharging capacities of the high-SSA sample showed the highest capacity above 80 % at 0.2C. However, the capacities were decreased with decreasing SSA of the β-Ni(OH)₂ prepared. It was also found that, at lower SSA, charging/discharging rates below 1C did not affect the discharging capacity, i.e., the almost same capacities for 0.2C and 1C. Cyclic voltammetry revealed that the electrochemical reactions for the charging/discharging were considered to be reversible and smooth at various scanning rates. The rate-determining step of the electrochemical reaction is considered to be regulated by the diffusion of the active species involved for the lower SSA samples. However, for the higher SSA sample (280 m² g⁻¹) obtained at 200 °C in the presence of 1.0 × 10⁻¹ mol L⁻¹ guanidine carbonate strongly indicates the effects of the rate of surface reaction or electronic conductivity on rate-determining step of charging/discharging of the material.     

Facile Solvothermal Synthesis Ni(OH)<Subscript>2</Subscript> Nanostructure for Electrochemical Capacitors

Nickel hydroxide nanosheets were successfully synthesized by facile solvothermal method without any template. The structure and morphology of the as-prepared sample were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and transmission electron microscopy. The observations revealed the formation of hexagonal phase β-Ni(OH)₂ nanosheets with an average diameter of about 100–120 nm. Electrochemical studies were carried out using cyclic voltammetry and galvanostatic charge–discharge tests, respectively. A maximum specific capacitance of 2,342 F g⁻¹, which is the highest reported for a β-Ni(OH)₂ electrode, could be achieved in 6 mol L⁻¹ KOH electrolyte within the potential range of 0–0.50 V (vs. SCE) for the obtained β-Ni(OH)₂ electrode at 0.4 A g⁻¹, suggesting its potential application in the electrode material for electrochemical capacitors.