A complete single-chip GPS receiver with 1.6-V 24-mW radio in 0.18-/spl mu/m CMOS

We have developed a complete single-chip GPS receiver using 0.18-/spl mu/m CMOS to meet several important requirements, such as small size, low power, low cost, and high sensitivity for mobile GPS applications. This is the first case in which a radio has been successfully combined with a baseband processor, such as SoC, in a GPS receiver. The GPS chip, with a total size of 6.3 mm /spl times/ 6.3 mm, contains a 2.3 mm /spl times/ 2.0 mm radio part, including RF front end, phase-locked loops, IF functions, and 500 K gates of baseband logic, including mask ROM, SRAM, and dual port SRAM . It is fabricated using 0.18-/spl mu/m CMOS technology with a MIM capacitor and operates from a 1.6-2.0-V power supply. Experimental results show a very low power consumption of, typically, 57 mW for a fully functional chip including baseband, and a high sensitivity of -152dBm. Through countermeasures against substrate coupling noise from the digital part, the high sensitivity was successfully achieved without any external low-noise amplifier.     

A 1-V 24-GHz 17.5-mW phase-locked loop in a 0.18-/spl mu/m CMOS process

A 1-V 24-GHz 17.5-mW fully integrated phase-locked loop employing a transformer-feedback voltage-controlled oscillator and a stacked divide-by-2 frequency divider for low voltage and low power is presented. Implemented in a 0.18-/spl mu/m CMOS process and operated at 24 GHz with a 1-V supply, the PLL measures in-band phase noise of -106.3 dBc at a frequency offset of 100 kHz and out-of-band phase noise of -119.1 dBc/Hz at a frequency offset of 10 MHz. The PLL dissipates 17.5 mW and occupies a core area of 0.55 mm/sup 2/.     

A 35-mW 3.6-mm/sup 2/ fully integrated 0.18-/spl mu/m CMOS GPS radio

A single-chip CMOS Global Positioning System (GPS) radio has been integrated using only a couple of external passive components for the input matching network and one external reference for the synthesizer. The receiver downconverts the GPS L1 signal at 1575.42 MHz to an IF of 9.45 MHz. The complete front-end and frequency synthesizer section have been integrated: low noise amplifier, image rejection mixer, IF active filter, and the full phase-locked loop synthesizer, including voltage-controlled oscillator and loop filter. The front-end measured performances are 81-dB maximum gain, 5.3-dB noise figure, and >30-dB image rejection. The synthesizer features a phase noise of -95 dBc/Hz at 1-MHz offset and a total integrated phase noise of less than 7/spl deg/ rms in the 500-Hz-1.5-MHz band. The front-end and the synthesizer draw, respectively, 11 and 9 mA from a 1.8-V supply. The architecture of the front-end and synthesizer has been geared to high level of integration and reduction of silicon area at the lowest possible power consumption. Consequently, the one reported here is the smallest and most integrated CMOS GPS receiver reported so far.     

A Bluetooth radio in 0.18-/spl mu/m CMOS

This paper describes the results of an implementation of a Bluetooth radio in a 0.18-/spl mu/m CMOS process. A low-IF image-reject conversion architecture is used for the receiver. The transmitter uses direct IQ-upconversion. The VCO runs at 4.8-5.0 GHz, thus facilitating the generation of 0/spl deg/ and 90/spl deg/ signals for both the receiver and transmitter. By using an inductor-less LNA and the extensive use of mismatch simulations, the smallest silicon area for a Bluetooth radio implementation so far can be reached: 5.5 mm/sup 2/. The transceiver consumes 30 mA in receive mode and 35 mA in transmit mode from a 2.5 to 3.0-V power supply. As the radio operates on the same die as baseband and SW, the crosstalk-on-silicon is an important issue. This crosstalk problem was taken into consideration from the start of the project. Sensitivity was measured at -82 dBm.     

A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

0.18-/spl mu/m CMOS Bluetooth analog receiver with -88-dBm sensitivity

A CMOS Bluetooth analog low-IF receiver that includes a low-noise amplifier, image-rejection mixer, IF bandpass active filter, and programmable gain amplifier (PGA) was fabricated in a 0.18-/spl mu/m bulk CMOS process. In order to achieve good sensitivity and tolerance against blocking signals, operational amplifiers were used in the active filter and PGA, the filter and PGA were interleaved to minimize noise, and an on-chip automatic tuner adjusts the filter frequency. Other features included a feedforward automatic gain control with rapid convergence. When connected to the digital demodulator of a BiCMOS Bluetooth transceiver, -88-dBm sensitivity was measured at 65-mW power dissipation. All blocking signal specifications were also satisfied.     

0.18 /spl mu/m CMOS backplane receiver with decision-feedback equalisation embedded

Decision-feedback equalisation (DFE) is explored to reduce intersymbol interference and crosstalks in high-speed backplane applications. In the design of the clock and data recovery circuit, embedding DFE within a phase and frequency detector enhances the recovery of data inherently from distorted input signals and facilitates providing DFE with the recovered clock.     

A 3-V, 0.35-/spl mu/m CMOS Bluetooth receiver IC

A fully integrated CMOS low-IF Bluetooth receiver is presented. The receiver consists of a radio frequency (RF) front end, a phase-locked loop (PLL), an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, and a frequency offset cancellation circuit. The highlights of the receiver include a low-power active complex filter with a nonconventional tuning scheme and a high-performance mixed-mode GFSK demodulator. The chip was fabricated on a 6.25-mm/sup 2/ die using TSMC 0.35-/spl mu/m standard CMOS process. -82 dBm sensitivity at 1e-3 bit error rate, -10 dBm IIP3, and 15 dB noise figure were achieved in the measurements. The receiver active current is about 65 mA from a 3-V power supply.     

A high-speed 850-nm optical receiver front-end in 0.18-/spl mu/m CMOS

A high-speed optical interface circuit for 850-nm optical communication is presented. Photodetector, transimpedance amplifier (TIA), and post-amplifier are integrated in a standard 0.18-/spl mu/m 1.8-V CMOS technology. To eliminate the slow substrate carriers, a differential n-well diode topology is used. Device simulations clarify the speed advantage of the proposed diode topology compared to other topologies, but also demonstrate the speed-responsivity tradeoff. Due to the lower responsivity, a very sensitive transimpedance amplifier is needed. At 500 Mb/s, an input power of -8 dBm is sufficient to have a bit error rate of 3/spl middot/10/sup -10/. Next, the design of a broadband post-amplifier is discussed. The small-signal frequency dependent gain of the traditional and modified Cherry-Hooper stage is analyzed. To achieve broadband operation in the output buffer, so-called "f/sub T/ doublers" are used. For a differential 10 mV/sub pp/ 2/sup 31/-1 pseudo random bit sequence, a bit error rate of 5/spl middot/10/sup -12/ at 3.5 Gb/s has been measured. At lower bit-rates, the bit error rate is even lower: a 1-Gb/s 10-mV/sub pp/ input signal results in a bit error rate of 7/spl middot/10/sup -14/. The TIA consumes 17mW, while the post-amplifier circuit consumes 34 mW.     

A 2.4-GHz RF sampling receiver front-end in 0.18-/spl mu/m CMOS

This paper presents an integrable RF sampling receiver front-end architecture, based on a switched-capacitor (SC) RF sampling downconversion (RFSD) filter, for WLAN applications in a 2.4-GHz band. The RFSD filter test chip is fabricated in a 0.18-/spl mu/m CMOS technology and the measurement results show a successful realization of RF sampling, quadrature downconversion, tunable anti-alias filtering, downconversion to baseband, and decimation of the sampling rate. By changing the input sampling rate, the RFSD filter can be tuned to different RF channels. A maximum input sampling rate of 1072 MS/s has been achieved. A single-phase clock is used for the quadrature downconversion and the bandpass operation is realized by a 23-tap FIR filter. The RFSD filter has an IIP/sub 3/ of +5.5 dBm, a gain of -1 dB, and more than 17 dB rejection of alias bands. The measured image rejection is 59 dB and the sampling clock jitter is 0.64 ps. The test chip consumes 47 mW in the analog part and 40 mW in the digital part. It occupies an area of 1 mm/sup 2/.     

OC-192 transmitter and receiver in standard 0.18-/spl mu/m CMOS

This paper presents the first fully integrated SONET OC-192 transmitter and receiver fabricated in a standard 0.18-/spl mu/m CMOS process. The transmitter consists of an input data register, 16-b-wide first-in-first-out (FIFO) circuit, clock multiplier unit (CMU), and 16:1 multiplexer to give a 10-Gb/s serial output. The receiver integrates an input amplifier for 10-Gb/s data, clock and data recovery circuit (CDR), 1:16 demultiplexer, and drivers for low-voltage differential signal (LVDS) outputs. An on-chip LC-type voltage-controlled oscillator (VCO) is employed by both the transmitter and receiver. The chipset operates at multiple data rates (9.95-10.71 Gb/s) with functionality compatible with the multisource agreement (MSA) for 10-Gb transponders. Both chips demonstrate SONET-compliant jitter characteristics. The transmitter 10.66-GHz output clock jitter is 0.065 UI/sub pp/ (unit interval, peak-to-peak) over a 50-kHz-80-MHz bandwidth. The receiver jitter tolerance is more than 0.4 UI/sub pp/ at high frequencies (4-80 MHz). A high level of integration and low-power consumption is achieved by using a standard CMOS process. The transmitter and receiver dissipate a total power of 1.32 W at 1.8 V and are packaged in a plastic ball grid array with a footprint of 11/spl times/11 mm/sup 2/.     

A 0.18-/spl mu/m CMOS bioluminescence detection lab-on-chip

The paper describes a bioluminescence detection lab-on-chip consisting of a fiber-optic faceplate with immobilized luminescent reporters/probes that is directly coupled to an optical detection and processing CMOS system-on-chip (SoC) fabricated in a 0.18-/spl mu/m process. The lab-on-chip is customized for such applications as determining gene expression using reporter gene assays, determining intracellular ATP, and sequencing DNA. The CMOS detection SoC integrates an 8 /spl times/ 16 pixel array having the same pitch as the assay site array, a 128-channel 13-bit ADC, and column-level DSP, and is fabricated in a 0.18-/spl mu/m image sensor process. The chip is capable of detecting emission rates below 10/sup -6/ lux over 30 s of integration time at room temperature. In addition to directly coupling and matching the assay site array to the photodetector array, this low light detection is achieved by a number of techniques, including the use of very low dark current photodetectors, low-noise differential circuits, high-resolution analog-to-digital conversion, background subtraction, correlated multiple sampling, and multiple digitizations and averaging to reduce read noise. Electrical and optical characterization results as well as preliminary biological testing results are reported.     

A low-voltage folded-switching mixer in 0.18-/spl mu/m CMOS

Scaling of CMOS technologies has a great impact on analog design. The most severe consequence is the reduction of the voltage supply. In this paper, a low voltage, low power, AC-coupled folded-switching mixer with current-reuse is presented. The main advantages of the introduced mixer topology are: high voltage gain, moderate noise figure, moderate linearity, and operation at low supply voltages. Insight into the mixer operation is given by analyzing voltage gain, noise figure (NF), linearity (IIP3), and DC stability. The mixer is designed and implemented in 0.18-/spl mu/m CMOS technology with metal-insulator-metal (MIM) capacitors as an option. The active chip area is 160 /spl mu/m/spl times/200 /spl mu/m. At 2.4 GHz a single side band (SSB) noise figure of 13.9 dB, a voltage gain of 11.9 dB and an IIP3 of -3 dBm are measured at a supply voltage of 1 V and with a power consumption of only 3.2 mW. At a supply voltage of 1.8 V, an SSB noise figure of 12.9 dB, a voltage gain of 16 dB and an IIP3 of 1 dBm are measured at a power consumption of 8.1 mW.     

A 15-mW fully integrated I/Q synthesizer for Bluetooth in 0.18-/spl mu/m CMOS

A low-power fully integrated synthesizer for Bluetooth applications is presented. The circuit with quadrature output signals at 2.45 GHz and 15-mW power dissipation has been designed in a digital 0.18-/spl mu/m CMOS process with 1.8-V supply voltage. The only external component is a 64-MHz crystal. Measurements have been performed on packaged samples mounted on an FR-4 board and show that the Bluetooth requirements are met. The measured phase noise is below -120 dBc/Hz at 3-MHz offset, and the resulting residual frequency modulation is 7.4-kHz rms. The tuning range consists of an analog and digital tuning mechanism, resulting in more than 15% overall tuning range.     

A 1.8-V 2.4/5.15-GHz dual-band LCVCO in 0.18-/spl mu/m CMOS technology

A dual band, fully integrated, low phase-noise and low-power LC voltage-controlled oscillator (VCO) operating at the 2.4-GHz industrial scientific and medical band and 5.15-GHz unlicensed national information infrastructure band has been demonstrated in an 0.18-/spl mu/m CMOS process. At 1.8-V power supply voltage, the power dissipation is only 5.4mW for a 2.4-GHz band and 8mW for a 5.15-GHz band. The proposed VCO features phase-noise of -135dBc/Hz at 3-MHz offset frequency away from the carrier frequency of 2.74GHz and -126dBc/Hz at 3-MHz offset frequency away from 5.49GHz. The oscillator is tuned from 2.2 to 2.85GHz in the low band (2.4-GHz band) and from 4.4 to 5.7GHz in the high band (5.15-GHz band).     

A matrix amplifier in 0.18-/spl mu/m SOI CMOS

A fully integrated matrix amplifier with two rows and four columns (2-by-4) fabricated in a three-layer metal 0.18-/spl mu/m silicon-on-insulator (SOI) CMOS process is presented. It exhibits an average pass-band gain of 15 dB and a unity-gain bandwidth of 12.5 GHz. The input and output ports are matched to 50 /spl Omega/ using m-derived half sections; the measured S/sub 11/ and S/sub 22/ values exceed -7 and -12 dB, respectively. Integrated in 2.0/spl times/2.9mm/sup 2/, it dissipates 233.4 mW total from 2.4- and 1.8-V power supplies.     

24 GHz low-noise amplifier in 0.18 /spl mu/m CMOS technology

A 24 GHz monolithic low-noise amplifier (LNA) is implemented in a standard 0.18 /spl mu/m CMOS technology. Measurements show a gain of 12.86 dB and a noise figure of 5.6 dB at 23.5 GHz. The input and output return losses are better than 11 dB and 22 dB across the 22-29 GHz span, respectively. The operation frequency of 24 GHz is believed to be the highest reported for LNA in a standard CMOS technology.     

A 25-MS/s 14-b 200-mW /spl Sigma//spl Delta/ Modulator in 0.18-/spl mu/m CMOS

The design of a fifth-order 4-b quantizer single-loop /spl Sigma//spl Delta/ modulator is presented that achieves 25-MS/s conversion rate with 84 dB of dynamic range and 82 dB of signal-to-noise ratio. Implemented in a 0.18-/spl mu/m CMOS technology, the 0.95-mm/sup 2/ chip has a power consumption of 200 mW from a 1.8-V supply.     

0.18 /spl mu/m 3-6 GHz CMOS broadband LNA for UWB radio

A 3-6 GHz CMOS broadband low noise amplifier (LNA) for ultra-wideband (UWB) radio is presented. The LNA is fabricated with the 0.18 /spl mu/m 1P6M standard CMOS process. Measurement of the CMOS LNA is performed using an FR-4 PCB test fixture. From 3 to 6 GHz, the broadband LNA exhibits a noise figure of 4.7-6.7 dB, a gain of 13-16 dB, and an input/output return loss higher than 12/10 dB, respectively. The input P/sub 1 dB/ and input IP3 (IIP3) at 4.5 GHz are about -14 and -5 dBm, respectively. The DC supply is 1.8 V.     

A 1-V 2.5-mW 5.2-GHz frequency divider in a 0.35-/spl mu/m CMOS process

A 1-V low-power high-speed dynamic-loading frequency divider is proposed using novel D flip-flops with a common-gate topology and with a single clock phase. A simple and accurate small-signal analysis model is provided to estimate the operating frequencies of the divider. Implemented in a standard digital 0.35-/spl mu/m CMOS process and at 1-V supply, the proposed frequency divider measures a maximum operating frequency up to 5.2 GHz with a power consumption of 2.5 mW.