Influence of NO2 on the selective catalytic reduction of NO with ammonia over Fe-ZSM5

The influence of NO₂ on the selective catalytic reduction (SCR) of NO with ammonia was studied over Fe-ZSM5 coated on cordierite monolith. NO₂ in the feed drastically enhanced the NO_x removal efficiency (DeNOx) up to 600 °C, whereas the promoting effect was most pronounced at the low temperature end. The maximum activity was found for NO₂/NO_x = 50%, which is explained by the stoichiometry of the actual SCR reaction over Fe-ZSM5, requiring a NH₃:NO:NO₂ ratio of 2:1:1. In this context, it is a special feature of Fe-ZSM5 to keep this activity level almost up to NO₂/NO_x = 100%. The addition of NO₂ to the feed gas was always accompanied by the production of N₂O at lower and intermediate temperatures. The absence of N₂O at the high temperature end is explained by the N₂O decomposition and N₂O-SCR reaction. Water and oxygen influence the SCR reaction indirectly. Oxygen enhances the oxidation of NO to NO₂ and water suppresses the oxidation of NO to NO₂, which is an essential preceding step of the actual SCR reaction for NO₂/NO_x < 50%. DRIFT spectra of the catalyst under different pre-treatment and operating conditions suggest a common intermediate, from which the main product N₂ is formed with NO and the side-product N₂O by reaction with gas phase NO₂.     

Alumina- and titania-based monolithic catalysts for low temperature selective catalytic reduction of nitrogen oxides

The selective catalytic reduction of NO+NO₂ (NO_x) at low temperature (180–230°C) with ammonia has been investigated with copper-nickel and vanadium oxides supported on titania and alumina monoliths. The influence of the operating temperature, as well as NH₃/NO_x and NO/NO₂ inlet ratios has been studied. High NO_x conversions were obtained at operating conditions similar to those used in industrial scale units with all the catalysts. Reaction temperature, ammonia and nitrogen dioxide inlet concentration increased the N₂O formation with the copper-nickel catalysts, while no increase was observed with the vanadium catalysts. The vanadium-titania catalyst exhibited the highest DeNO_x activity, with no detectable ammonia slip and a low N₂O formation when NH₃/NO_x inlet ratio was kept below 0.8. TPR results of this catalyst with NO/NH₃/O₂, NO₂/NH₃/O₂ and NO/NO₂/NH₃/O₂ feed mixtures indicated that the presence of NO₂ as the only nitrogen oxide increases the quantity of adsorbed species, which seem to be responsible for N₂O formation. When NO was also present, N₂O formation was not observed.     

Selective reduction of NO by NH3 over manganese–cerium mixed oxides: Relation between adsorption, redox and catalytic behavior

Manganese–cerium mixed oxide catalysts with different molar ratio Mn/(Mn + Ce) (0, 0.25, 0.50, 0.75, 1) were prepared by citric acid method and investigated concerning their adsorption behavior, redox properties and behavior in the selective catalytic reduction of NO_x by NH₃. The studies based on pulse thermal analysis combined with mass spectroscopy and FT-IR spectroscopy uncovered a clear correlation between the dependence of these properties and the mixed oxide composition. Highest activity to nitrogen formation was found for catalysts with a molar ratio Mn/(Mn + Ce) of 0.25, whereas the activity was much lower for the pure constituent oxides. Measurements of adsorption uptake of reactants, NO_x (NO, NO₂) and NH₃, and reducibility showed similar dependence on the mixed oxide composition indicating a clear correlation of these properties with catalytic activity. The adsorption studies indicated that NO_x and NH₃ are adsorbed on separate sites. Consecutive adsorption measurements of the reactants showed similar uptakes as separate measurements indicating that there was no interference between adsorbed reactants. Mechanistic investigations by changing the sequence of admittance of reactants (NO_x, NH₃) indicated that at 100–150 °C nitrogen formation follows an Eley–Rideal type mechanism, where adsorbed ammonia reacts with NO_x in the gas phase, whereas adsorbed NO_x showed no significant reactivity under conditions used.     

Effect of oxygen concentration on the NOx reduction with ammonia over V2O5–WO3/TiO2 catalyst

The catalytic reduction of NO_x in the typical operation temperatures and oxygen concentrations of diesel engines has been studied in the presence of V3W9Ti in a tubular flow reactor. The results have shown that the selective catalytic reduction is strongly affected by the oxygen concentration in low temperature range (150–275 °C). At higher temperatures, the reaction becomes independent of the O₂ concentration. The rate of the selective catalytic reduction of NO with ammonia may be considerably enhanced by converting part of the NO into NO₂. DRIFT measurements have shown that NH₃ and NO₂ are adsorbed on the catalyst surface on the contrary of NO. The experiments have shown that the decrease in N₂ selectivity of the SCR reaction is mainly due to the SCO of ammonia and to the formation of nitrous oxide.     

Selective catalytic reduction of NO and NO2 at low temperatures

The fast SCR reaction using equimolar amounts of NO and NO₂ is a powerful means to enhance the NO_x conversion over a given SCR catalyst. NO₂ fractions in excess of 50% of total NO_x should be avoided because the reaction with NO₂ only is slower than the standard SCR reaction.

At temperatures below 200 °C, due to its negative temperature coefficient, the ammonium nitrate reaction gets increasingly important. Half of each NH₃ and NO₂ react to form dinitrogen and water in analogy to a typical SCR reaction. The other half of NH₃ and NO₂ form ammonium nitrate in close analogy to a NO_x storage-reduction catalyst. Ammonium nitrate tends to deposit in solid or liquid form in the pores of the catalyst and this will lead to its temporary deactivation.

The various reactions have been studied experimentally in the temperature range 150–450 °C for various NO₂/NO_x ratios. The fate of the deposited ammonium nitrate during a later reheating of the catalyst has also been investigated. In the absence of NO, the thermal decomposition yields mainly ammonia and nitric acid. If NO is present, its reaction with nitric acid on the catalyst will cause the formation of NO₂.     

An examination of the role of plasma treatment for lean NOx reduction over sodium zeolite Y and gamma alumina Part 1. Plasma assisted NOx reduction over NaY and Al2O3

The role of plasma processing on NO_x reduction over γ-alumina and a basic zeolite, NaY was examined. During the plasma treatment NO is oxidized to NO₂ and propylene is partially oxidized to CO, CO₂, acetaldehyde, and formaldehyde. With plasma treatment, NO as the NO_x gas, and a NaY catalyst, the maximum NO_x conversion was 70% between 180 and 230 °C. The activity decreased at higher and lower temperatures.

As high as 80% NO_x removal over gamma alumina was measured by a chemiluminescent NO_x meter with plasma treatment and NO as the NO_x gas.

For both catalysts a simultaneous decrease in NO_x and aldehydes concentrations was observed, which suggests that aldehyde may be important components for NO_x reduction in plasma-treated exhaust.     

Zeolite-mediated removal of NOx by NH3 from exhaust streams at low temperatures

NH₃ stored on zeolites in the form of NH₄⁺ ions easily reacts with NO to N₂ in the presence of O₂ at temperatures <373 K under dry conditions. Wet conditions require a modification of the catalyst system. It is shown that MnO₂ deposited on the external surface of zeolite Y by precipitation considerably enhances the NO_x conversion by zeolite fixed NH₄⁺ ions in the presence of water at 400–430 K. Particle-size analysis, temperature-programmed reduction, textural characterization, chemical analysis, ESR and XRD gave a subtle picture of the MnO₂ phase structure. The MnO₂ is a non-stoichiometric, amorphous phase that contains minor amounts of Mn²⁺ ions. It loses O₂ upon inert heating up to 873 K, but does not crystallize or sinter. The phase is reducible by H₂ in two stages via intermediate formation of Mn₃O₄. The manufacture of extrudates preserving stored NH₄⁺ ions for NO_x reduction is described. It was found that MnO₂ can oxidize NO by bulk oxygen. This enables the reduction of NO to N₂ by the zeolitic NH₄⁺ ions without gas-phase oxygen for limited time periods. The composite catalyst retains storage capacity for both, oxygen and NH₄⁺ ions despite the presence of moisture and allows short-term reduction of NO without gaseous O₂ or additional reductants. The catalyst is likewise suitable for steady-state DeNO_x operation at higher space velocities if gaseous NH₃ is permanently supplied.     

Hysteresis in activity of microporous lean NOx catalysts in the presence of water vapor

Increasingly stringent ambient air quality standards coupled with the need to improve fuel economy has drawn significant attention to the search for emission control systems for lean burn engine vehicles. Much of the focus has been on zeolite-based catalysts for the conversion of NO_x to N₂ for automotive exhaust emission control. Under certain conditions, these catalysts are highly active catalysts for the reduction of NO_x using hydrocarbons as the reductant. However, many of these catalysts suffer from a variety of deactivation processes such as irreversible poisoning by SO_x or hydrothermal dealumination.

In addition to these deactivation processes, a recent focus of our research has been on the influence of water vapor on the activity of zeolite-based catalysts at low operating temperatures. We observe a hysteresis in catalytic activity of lean NO_x reduction (NO feed concentrations <100 ppm) upon increasing and decreasing temperature ramps at the low end of the operating window, that being from 100 to 300 °C using hydrocarbons as reductants. We describe these reversible influences of water vapor and the implications for this hysteresis in catalytic activity for the application of zeolite-based catalysts in lean NO_x catalysis, and compare these results to the instance of using ammonia as reductant.     

Activity and stability of Ag–alumina for the selective catalytic reduction of NOx with methane in high-content SO2 gas streams

In this work, we investigated the activity and stability of Ag–alumina catalysts for the SCR of NO with methane in gas streams with a high concentration of SO₂, typical of coal-fired power plant flue gases. Ag–alumina catalysts were prepared by coprecipitation–gelation, and dilute nitric-acid solutions were used to remove weakly bound silver species from the surface of the as prepared catalysts after calcination. SO₂ has a severe inhibitory effect, essentially quenching the CH₄-SCR reaction on this type catalysts at temperatures <600 °C. SO₂ adsorbs strongly on the surface forming aluminum and silver sulfates that are not active for CH₄-SCR of NO_x. Above 600 °C, however, the reaction takes place without catalyst deactivation even in the presence of 1000 ppm SO₂. The reaction light-off coincides with the onset of silver sulfate decomposition, indicating the critical role of silver in the reaction mechanism. SO₂ is reversibly adsorbed on silver above 600 °C. While alumina sites remain sulfated, this does not hinder the reaction. Sulfation of alumina only decreases the extent of adsoption of NO_x, but adsorption of NO_x is not the limiting step. Methane activation is the limiting step, hence the presence of sulfur-free Ag–O–Al species is a requirement for the reaction. Strong adsorption of SO₂ on Ag–alumina decreases the rates of the reaction, and increases the activation energies of both the reduction of NO to N₂ and the oxidation of CH₄, the latter more than the former. Our results indicate partial contribution of gas phase reactions to the formation of N₂ above 600 °C. H₂O does not inhibit the reaction at 625 °C, and the effect of co-addition of H₂O and SO₂ is totally reversible.     

An examination of the role of plasma treatment for lean NOx reduction over sodium zeolite Y and gamma alumina Part 2: Formation of nitrogen

NO_x reduction with NO₂ as the NO_x gas in the absence of plasma was compared to plasma treated lean NO_x exhaust where NO is converted to NO₂ in the plasma. Product nitrogen was measured to prove true chemical reduction of NO_x to N₂. With plasma treatment, NO as the NO_x gas, and a NaY catalyst, the maximum conversion to nitrogen was 50% between 180 and 230 °C. The activity decreased at higher and lower temperatures. At 130 °C a complete nitrogen balance could be obtained, however between 164 and 227 °C less than 20% of the NO_x is converted to a nitrogen-containing compound or compounds not readily detected by gas chromatograph (GC) or Fourier transform infrared spectrometer (FT-IR) analysis. With plasma treatment, NO₂ as the NO_x gas, and a NaY catalyst, a complete nitrogen balance is obtained with a maximum conversion to nitrogen of 55% at 225 °C.

For γ-alumina, with plasma treatment and NO₂ as the NO_x gas, 59% of the NO_x is converted to nitrogen at 340 °C. A complete nitrogen balance was obtained at these conditions. As high as 80% NO_x removal over γ-alumina was measured by a chemiluminescent NO_x meter with plasma treatment and NO as the NO_x gas.

When NO is replaced with NO₂ and the simulated exhaust gases are not plasma treated, the maximum NO_x reduction activity of NaY and γ-alumina decreases to 26 and 10%, respectively. This is a large reduction in activity compared to similar conditions where the simulated exhaust was plasma treated. Therefore, in addition to NO₂, other plasma-generated species are required to maximize NO_x reduction.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

NOX removal in excess oxygen by plasma-enhanced selective catalytic reduction

In the off-gases of internal combustion engines running with oxygen excess, non-thermal plasmas (NTPs) have an oxidative potential, which results in an effective conversion of NO to NO₂. In combination with appropriate catalysts and ammonia (NH₃-SCR) or hydrocarbons (HC-SCR) as a reducing agent, this can be utilized to reduce nitric oxides (NO and NO₂) synergistically to molecular nitrogen.

The combination of SCR and cold plasma enhanced the overall reaction rate and allowed an effective removal of NO_X at low temperatures. Using NH₃ as a reducing agent, NO_X was converted to N₂ on zeolites or NH₃-SCR catalysts like V₂O₅–WO₃/TiO₂ at temperatures as low as 100–200 °C. Significant synergetic effects of plasma and catalyst treatment were observed both for NH₃ stored by ion exchange on the zeolite and for continuous NH₃ supply.

Certain modifications of Al₂O₃ and ZrO₂ have been found to be effective as catalysts in the plasma-assisted HC-SCR in oxygen excess. With an energy supply of about 30 eV/NO-molecule, 500 ppm NO was reduced by more than half at a temperature of 300 °C and a space velocity of 20 000 h⁻¹ at the catalyst. The synergistic combinations of NTP and both NH₃- and HC-SCR have been verified under real diesel engine exhaust conditions.     

Potassium–copper and potassium–cobalt catalysts supported on alumina for simultaneous NOx and soot removal from simulated diesel engine exhaust

This paper deals with the activity of bimetallic potassium–copper and potassium–cobalt catalysts supported on alumina for the reduction of NO_x with soot from simulated diesel engine exhaust. The effect of the reaction temperature, the soot/catalyst mass ratio and the presence of C₃H₆ has been studied. In addition, the behavior of two monometallic catalysts supported on zeolite beta (Co/beta and Cu/beta), previously used for NO_x reduction with C₃H₆, as well as a highly active HC-SCR catalyst (Pt/beta) has been tested for comparison. The preliminary results obtained in the absence of C₃H₆ indicate that, at temperatures between 250 and 400 °C, the use of bimetallic potassium catalysts notably increases the rate of NO_x reduction with soot evolving N₂ and CO₂ as main reaction products. At higher temperatures, the catalysts mainly favor the direct soot combustion with oxygen. In the presence of C₃H₆, an increase in the activity for NO_x reduction has been observed for the catalyst with the highest metal content. At 450 °C, the copper-based catalysts (Cu/beta and KCu2/Al₂O₃) show the highest activity for both NO_x reduction (to N₂ and CO₂) and soot consumption. The Pt/beta catalyst does not combine, at any temperature, a high NO_x reduction with a high soot consumption rate.     

A practical scale evaluation of sulfated V2O5/TiO2 catalyst from metatitanic acid for selective catalytic reduction of NO by NH3

The characteristics of sulfated V₂O₅/TiO₂ honeycomb catalyst from metatitanic acid (MTA) were studied in the practical conditions of pilot plant using high dust flue gas from coal fired utility boiler. The effects of reaction temperature, NH₃/NO mole ratio, space velocity and operation time on the reduction of nitric oxide (NO) were mainly investigated for engineering application. The catalyst showed high NO reduction of about 90% at a space velocity of 4000 h⁻¹, NH₃/NO mole ratio of 1.0 and reaction temperature of 300–400 °C. The efficiency of this catalyst remained constant during the present experiment of 2400 h and the erosion by fly ash was lower than that of the commercial catalysts. These results clearly demonstrate the high potential for this catalyst to be applied commercially for the control of NO_x emissions from coal fired utility boiler.     

Novel low temperature NOx storage-reduction catalysts for diesel light-duty engine emissions based on hydrotalcite compounds

A series of Pt and Pt,Cu supported catalysts were prepared by wet impregnation of Mg–Al supports obtained from hydrotalcite-type (HT) precursor compounds. These novel NO_x storage-reduction (NO_xSR) catalysts show improved performances in NO_x storage than Pt,Ba/alumina NO_xSR catalysts at reaction temperatures lower than 200 °C. These catalysts show also improved resistance to deactivation by SO₂. The effect is attributed to the formation of well dispersed Mg(Al)O particles which show good NO_x storage properties. The promoted low temperature activity is explained by the lower basicity of the Mg(Al)O mixed oxide in comparison to BaO, which induces on one hand a lower inhibition on Pt activity (NO to NO₂ oxidation and/or hydrocarbon oxidation) due to electronic effect, and on the other hand a lower thermal stability of the stored NO_x. The presence of Cu slightly inhibits activity at low temperature, although improves activity and resistance to deactivation at 300 °C. On these catalysts FT-IR characterization evidences the formation of a Pt–Cu alloy after reduction.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

NOx storage and reduction characteristics of Pd/MnOx–CeO2 at low temperature

The reaction between hydrogen and NO was studied over 1 wt.% Pd supported on NO_x-sorbing material, MnO_x–CeO₂, at low temperatures. The result of pulse mode reactions suggest that NO_x adsorbed as nitrate and/or nitrite on MnO_x–CeO₂ was reduced by hydrogen, which was spilt-over from Pd catalyst. The NO_x storage and reduction (NSR) cycles were carried out over Pd/MnO_x–CeO₂ in a conventional flow reactor at 150 °C. In a storage step, NO was removed by the oxidative adsorption from a stream of 0.04–0.08% NO, 5–10% O₂, and He balance. This was followed by a reducing step, where a stream of 1% H₂/He was supplied to ensure the conversion of nitrate/nitrite to N₂ and thus restore the adsorbability. It was revealed that the NSR cycle is much more suitable for the H₂–deNO_x process in excess O₂, compared to a conventional steady state reaction mode.     

On the dynamic behavior of “NOx-storage/reduction” Pt–Ba/Al2O3 catalyst

The NO_x storage and reduction functions of a Pt–Ba/Al₂O₃ “NO_x storage–reduction” catalyst has been investigated in the present work by applying the transient response and the temperature programmed reaction methods, by using propylene as the reducing agent. It is found that: (i) the storage of NO_x occurs first at BaO and then at BaCO₃, which are the most abundant sites following regeneration of catalyst with propylene; (ii) the overall storage process at BaCO₃ is slower than at BaO; (iii) CO₂ inhibits the NO_x storage at low temperatures; (iv) the amount of NO_x stored up to catalyst saturation at 350 °C corresponds to 17.6% of Ba; (v) the reduction of stored NO_x groups is fast and is limited by the concentration of propylene in the investigated T range (250–400 °C); (vi) selectivity to N₂ is almost complete at 400 °C but is significantly lower at 300 °C due to the formation of NO which can be tentatively ascribed to the presence of unselective Pt–O species.     

Combinatorial preparation and high-throughput catalytic tests of multi-component deNOx catalysts

A quaternary catalyst library of 56 samples comprising all combinations of four elements, viz. Ag, Co, Cu, In, with six equally spaced atomic fraction increments from 0 to 1 was prepared by impregnation of a proprietary mesoporous alumina support. Catalytic properties of the library were tested in the selective catalytic reduction (SCR) of NO_x by propane under lean conditions in the temperature range 400–500 °C. The catalytic data acquired by a parallel 64-channel microreactor system with automated time-of-flight mass spectrometric analysis have been evaluated regarding selectivity–compositional relationships, synergistic effects for NO_x conversion, and efficiency of propane utilization. Full conversion of NO_x is achieved over Ag–Co combinations at 450 °C with N₂ selectivities of more than 90% and reductant utilization of 20% in a feed of 1500 ppm NO, 1500 ppm propane and 5 vol.% O₂ (space velocity of 36,000 cm³ g_cat⁻¹ h⁻¹). For the single-component catalysts Ag/Al₂O₃, Co/Al₂O₃, Cu/Al₂O₃, and In/Al₂O₃, the state of the elements on the mesoporous alumina was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Cobalt forms a spinel-like cobalt aluminate phase whereas copper and indium are present as oxides with small sizes not detectable by XRD. Silver occurs in both metallic state and as Ag₂O, and forms Ag_n clusters of at least two different sizes, predominantly with diameters of about 30 nm. The conclusions are consistent with the reducibility of the single-component catalysts samples by H₂. Surface area measurements and pore size distributions revealed reasonable modifications of the textural properties. The main pore size of the alumina support is decreased from 7 to ca. 5 nm after loading of the active components.     

Lean-DeNOx titania based monolithic catalysts

The activity of titania based copper and platinum monolithic catalysts in the reduction of nitrogen oxides was studied with exhaust gases from a Diesel engine injecting fuel as reductant. Combining both catalysts, a two-stage system was designed, studying the influence of the copper catalysts composition on its performance with synthetic gas mixtures. The influence of reactants concentration and operating conditions was also investigated. Taking into account these results, a double-bed system with a cell density of 33 cell cm⁻² (210 c.p.s.i.) was prepared. Linear velocity had a strong influence on the performance of the Pt catalyst and of the double-bed. Two NO_x conversion maxima were observed with Pt/TiO₂ at 225°C and 350°C operating at 6.6 m s⁻¹. Promising NO_x conversions were achieved in the temperature range 200–450°C.