Photosensitive poly(benzoxazole) based on precursor from diphenyl isophthalate and bis(o-aminophenol)

A new synthetic method for the preparation of poly(benzoxazole) (PBO) precursor, poly(o-hydroxyamide) (7) from bis(o-aminophenol) (5) and diphenyl isophthalate (6) has been developed. Polymer 7 was prepared by the polycondensation of 5 and 6 in 1-methyl-2-pyrrolidinone (NMP) at 185-205 °C. Model reactions were carried out in detail to elucidate appropriate conditions for the formation of 2-hydroxybenzanilide (3) from o-aminophenol (1) and phenyl benzoate (2). The photosensitive (PBO) precursor based on polymer 7 containing a 22% of benzoxazole unit and 30 wt% 1-{1,1-bis[4-(2-diazo-1-(2H)naphthalenone-5-sulfonyloxy)phenyl]ethyl}-4-{1-[4-(2-diazo-1(2H)naphthalenone-5-sulfonyloxy)phenyl]methylethyl}benzene (S-DNQ) showed a sensitivity of 110 mJ cm⁻² and a contrast of 5.0 when it was exposed to 436 nm light followed by developing with a 2.38 wt% aqueous tetramethylammonium hydroxide solution at room temperature. A fine positive image featuring 8 μm line and space patterns was observed on the film of the photoresist exposed to 200 mJ cm⁻² of UV-light at 436 nm by the contact mode.     

Highly optically transparent/low color polyimide films prepared from hydroquinone- or resorcinol-based bis(ether anhydride) and trifluoromethyl-containing bis(ether amine)s

Two series of novel polyimides (5a-g and 6a-g) containing flexible ether linkages and pendent trifluoromethyl (CF₃) groups were synthesized from 1,4-bis(3,4-dicarboxyphenoxy)benzene dianhydride (3a) and 1,3-bis(3,4-dicarboxyphenoxy)benzene dianhydride (3b) with various CF₃-substituted aromatic bis(ether amine)s (4a-g) via ring-opening polyaddition to poly(amic acid)s, followed by thermal or chemical imidization. These polyimides were readily soluble in a variety of organic solvents and could be solution-cast into flexible and tough films. The cast films exhibited high optical transparency and almost no color, with a UV-vis absorption edge of 368-382 nm and a very low b^∗ value (a yellowness index) of 6.2-15.5. They had good thermal stability with glass-transition temperatures of 186-288 °C, and most of them did not show significant decomposition before 500 °C. Moreover, these polyimide films also possessed low dielectric constants of 2.79-3.49 (at 1 MHz) and low water uptakes (<0.65 wt%).     

Synthesis and properties of various poly(diphenylacetylenes) containing tert-amine moieties

The polymerization of diphenylacetylene derivatives possessing tert-amine moieties, such as triphenylamine, N-substituted carbazole and indole, was examined in the presence of TaCl₅-n-Bu₄Sn (1:2) catalyst. A polymer with high molecular weight (M_w = 570 × 10³) was obtained in good yield by the polymerization of diphenylamine-containing monomer 1b, whereas the isopropylphenylamine derivative (1c) gave a polymer with relatively low molecular weight (M_w = 2.4 × 10³). The polymerization of monomer 1d containing cyclohexylphenylamine group did not proceed; however, carbazolyl- and indolyl-containing monomers also produced polymers. Poly(1b), poly(2f) and poly(4b) could be fabricated into free-standing membranes by casting toluene solutions of these polymers. The gas permeability of poly(1b) was too low to be evaluated accurately whereas poly(4b) possessing two chlorine atoms in the repeating unit showed higher gas permeability than that of poly(1b); furthermore, poly(2f) having trimethylsilyl and 3-methylindolyl groups exhibited relatively high gas permeability (). In the cyclic voltammograms of diphenylamino group-containing polymers, poly(1b) and poly(2b), the intensities of oxidation and reduction peaks decreased more than those of carbazolyl-containing poly(2a). The molar absorptivity (?) of poly(1b) at ∼700 nm increased with increasing applied voltage in the UV-vis spectrum.     

Synthesis and properties of organosoluble polyimides based on 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]cyclohexane

New aromatic diamine with cyclohexane cardo group substituted with trifluoromethyl group in the side chain, 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]cyclohexane (II), was prepared through the nucleophilic substitution reaction of 1,1-bis(4-hydroxyphenyl)cyclohexane and 2-chloro-5-nitrobenzotrifluoride in the presence of potassium carbonate, to yield the intermediate dinitro compound I, followed by catalytic reduction with hydrazine and Pd/C to afford the diamine II. Fluorinated polyimides (IVa-g) were prepared from the II with various aromatic dianhydrides via thermal or chemical imidization of poly(amic acid). These polyimides had inherent viscosity ranging from 0.72 to 1.16 dl/g and showed excellent solubility in a variety of organic solvents. They were soluble in a concentration of 10% in the amide polar solvent, and 1-5% in the other testing solvents. IV films showed good mechanical properties, excellent thermal stability. The 10% weight loss temperature was above 476 °C in nitrogen or air, and the glass transition temperature was recorded at 214-278 °C. In comparison of the IV series with the analogous nonfluorinated polyimides (V series) based on 1,1-bis[4-(4-aminophenoxy)phenyl]cyclohexane (II′), IV series revealed better solubility, lighter-colored and lower dielectric constants and moisture absorptions. Their films had cut-off wavelengths in the range of 364-414 nm, b^* value (a yellowness index) ranging from 3.3 to 66.3, dielectric constants of 3.02-3.55 (1 MHz), with moisture absorption of 0.16-0.36 wt%.     

Synthesis and properties of helical polyacetylenes containing carbazole

Novel acetylene monomers containing carbazole with chiral menthyl and bornyl groups, 9-(1R,2S,5R)-menthyloxycarbonyl-2-ethynylcarbazole (1), 9-(1S,2R,5S)-menthyloxycarbonyl-2-ethynylcarbazole (2), 9-(1R,2S,5R)-menthyloxycarbonyl-3-ethynylcarbazole (3) and 9-(1S)-bornyloxycarbonyl-2-ethynylcarbazole (4) were synthesized and polymerized with a Rh catalyst to give the corresponding polymers [poly(1)-poly(4)] with moderate M_n value of (11.5-92.2) × 10³ in good yields (77-89%). CD spectroscopic studies revealed that poly(1), poly(2) and poly(4) took predominantly one-handed helical structure in CHCl₃, THF, toluene, and CH₂Cl₂, while poly(3) did not. Addition of methanol to CHCl₃ solutions of poly(1) and poly(2) resulted in the formation of aggregates showing smaller CD signals at 275 and 320 nm. The helical structure of poly(1) and poly(2) was very stable against heating. The polymers emitted fluorescence in 0.40-2.90% quantum yields. Poly(4) exhibited an obvious oxidation peak at 1.10 V. The polymers were thermally stable below 300 °C.     

Colorless and high organosoluble polyimides from 2,5-bis(3,4-dicarboxyphenoxy)-t-butylbenzene dianhydride and aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A series of polyimides III_a-h characterized by colorlessness, high transparency, high solubility, and good mechanical property, was synthesized from the aromatic dianhydride, 2,5-bis(3,4-dicarboxyphenoxy)-t-butylbenzene dianhydride (I), and various aromatic diamines (II_a-h) with pendent trifluoromethyl group via polyaddition, chemical imidization, and direct cast films. The III series showed more colorless than the polyimides (V and VI series) of 2,2-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA) contained, the VI series was synthesized from the II with 6FDA. These films III had cut-off wavelengths between 371 and 376 nm, as well as b* value (a yellowness index) ranging from 3.0 to 4.7. In fact, it is so far the most colorless aromatic polyimide in our systematical researches. The III series had inherent viscosity ranging from 0.72 to 1.33 dL/g and showed excellent solubility in a variety of organic solvents. They were soluble in a concentration of 5-10% in the amide polar solvent, ether solvent, and chlorinated solvent. These films showed strength tensile of 97-123 MPa, dielectric constants of 2.78-3.28 (1 MHz), and moisture absorptions of 0.11-0.36 wt%. The glass transition temperature of the III series was recorded at 214-259 °C, the 10% weight loss temperature was over 468 °C, and the residue was more than 47% at 800 °C in nitrogen.     

Seven-membered ring excited-state intramolecular proton-transfer in 2-benzamido-3- (pyridin-2-yl)acrylic acid

Hydrogen bonding compound (E)-2-benzamido-3-(pyridin-2-yl) acrylic acid (1a) was synthesized and characterized by ¹H NMR, FT-IR, and X-ray diffraction analysis in comparison to its analog. These analyses show the existence of seven-membered ring intramolecular hydrogen bonding in 1a. The hydrogen bonding results in the increasing of pK_a comparing to its analog. Further investigation on the photophysical properties of 1a in selected solvents reveals that strong absorption appears at about 340 nm and dual emission at around 420 and 490 nm. The excited-state intramolecular proton-transfer in 1a is very sensitive to solvent polarity and fluoride ion. Theoretical studies also give evidence of excited-state intramolecular proton-transfer with quite low energy barrier.     

Copolymers containing pendant styryltriphenylamine and carbazole groups: Synthesis, optical, electrochemical properties and its blend with Ir(ppy)3

A series of vinyl copolymers (PVKST12-PVKST91) and homoploymer PVST containing pendant hole-transporting 4-(4-oxystyryl)triphenylamine (12-100 mol%) and carbazole chromophores were synthesized by radical copolymerization and employed as host for Ir(ppy)₃ phosphor to tune emission color. They were characterized using the ¹H NMR, FT-IR, absorption and photoluminescence spectra, elemental analysis, GPC, cyclic voltammetric and thermal analysis (DSC, TGA). Their weight-average molecular weights (M_w) and decomposition temperatures (T_d) were 1.46-5.68 × 10⁴ and 356-399 °C, respectively. The HOMO levels of PVKST12-PVKST91 and PVST, estimated from the onset oxidation potentials in cyclic voltammograms, were −5.40 to −5.14 eV, which are much higher than −5.8 eV of the conventional host poly(9-vinylcarbazole) (PVK) owing to high hole-affinity of the 4-(4-oxystyryl)triphenylamine groups. Therefore, copolymers PVKST are effective in reducing hole-injection barrier between the PEDOT:PSS and emitting layer. Electroluminescent devices [ITO/PEDOT:PSS/PVKST:Ir(ppy)₃:PBD/BCP/Ca/Al] using the hole-transporting PVKST as host were fabricated to tune the emission color. Their EL spectra showed a major emission at 515 nm and a minor peak at 435 nm attributed to Ir(ppy)₃ and 4-(4-oxystyryl)triphenylamine, respectively. The C.I.E. 1931 coordinates shift from (0.29, 0.61) for PVK to (0.33, 0.42) for PVST with an increase in 4-(4-oxystyryl)triphenylamine content.     

Synthesis of laterally attached side-chain liquid crystalline poly(p-phenylene vinylene) and polyfluorene derivatives for the application of polarized electroluminescence

Two series of poly(p-phenylene vinylene) and polyfluorene derivatives (PPV1-PPV4 and PF1-PF5) containing laterally attached penta(p-phenylene) mesogenes were synthesized and characterized. These polymers show nematic liquid crystalline behavior. The optical properties of the polymers were investigated by UV-vis absorption and photoluminescence spectrometers and these polymers were fabricated to form the polarized electroluminescent devices using poly(ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as an alignment layer. In the series of poly(p-phenylene vinylene) derivatives, polymer PPV4 offered the best EL device performance. It emitted yellow light at 588 nm at 4 V. The maximum brightness was about 1337 cd/m² at 9 V with a polarized ratio of 2.6. In another series of polyfluorene derivatives, PF4 offered the best EL device performance with the polarized ratio of 12.4 and a maximum luminescence of 1855 cd/m². In the case of polarized white light, as a consequence of blending small amount of PF4 and PF5 with a host polymer PF2, polarized ratio of up to 10.2 and a maximum brightness of 2454 cd/m² have been attained. The aligned films exhibited pronounced polarized ratio, implying that the polymers exhibit potential for linearly polarized LED application.     

Synthesis and characterization of chiral polythiophenes: Poly [(R)-(−) and (S)-(+)-2-(3′-thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate]

(R)-(−) (1) and (S)-(+)-2-(3′-Thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate (2) monomers were synthesized, characterized, and polymerized in chloroform using FeCl₃ as an oxidizing agent. Molecular weights of 2.6 × 10⁴ and 3.2 × 10⁴ for poly1 and poly2, respectively, were determined by SEC analysis. FTIR spectra of the polymers indicated the coupling of monomers through the α positions. UV-vis spectra showed absorption bands at λ_max = 226 and 423 nm for poly1 and poly2, ascribed to transitions of side groups and polythiophene backbone, respectively. Poly1 and poly2 remained stable up to 210 °C. At higher temperatures, a two step weight loss degradation process was observed for both polymers by TGA analysis. ¹H NMR, in the presence of Eu(tfc)₃, and optical rotation measurements indicate the chiral properties of the monomers 1 ([α]_D²⁸ = −76.2) and 2 ([α]_D²⁸ = +76.0), and the maintenance of chirality after polymerization (poly1 [α]_D²⁸ = −29.0 and poly2 [α]_D²⁸ = +28.4, c = 2.5 in THF). According to scanning electron microscopic analysis, the polymers are highly porous.     

Theoretical analysis on the geometries and electronic structures of coplanar conjugated poly(azomethine)s

In this study, theoretical analysis on the geometries and electronic properties of various conjugated poly(azomethine)s is reported. The theoretical ground-state geometry and electronic structure of the studied poly(azomethine)s are optimized by the hybrid density functional theory (DFT) method treated in periodic boundary conditions at the B3LYP level of theory with 6-31G basis set. The geometry and electronic structure of poly(1,4-phenylenemethylidyneitrilo-1,4-phenylene-nitrilomethylidyne) (PPI) are compared with those of poly(p-phenylene vinylene) (PPV) or polyazine (PAZ). The theoretical results suggest the non-coplanar conformation of PPI but PPV and PAZ with a coplanar conformation. The electronic properties of PPI are in the intermediate between PPV and PAZ. The non-coplanar conformation of PPI could be released if the phenylene ring is replaced by the five-member ring of 3,4-ethylenedioxythiophene (PEEI), pyrrole (PYYI), thiophene (PTTI), furan (PFFI), or thiadiazole (PThThI). The theoretical E_g of PEEI, PYYI, PFFI, and PTTI are in the range of 1.11-1.67 eV, which is due to the coplanar configuration or donor-acceptor intrachain charge transfer. However, the large bond length alternation or lack of charge transfer characteristic makes the PThThI with a larger E_g of 2.47 eV than others. The trend on the IP or EA of the studied conjugated poly(azomethine)s are consistent with the electronic characteristic of the aromatic ring. The upper valence bandwidth of the studied five-member ring based poly(azomethine)s except PThThI is in the range of 562-613 meV, which is larger than that of PPI (247 meV) or PPV (373 meV). The results suggest that the electronic properties of conjugated poly(azomethine)s could be varied through various ring structure. The proposed new coplanar conjugated poly(zomethine)s can be potentially used as transparent conductors or thin film transistors.     

Direct synthesis of soluble and thermally stable poly(urethane-imide)s from a new triimide-dicarbonylazide

A new aromatic dicarbonylazide (3) bearing three preformed imide rings was synthesized by treating N-[3,5-bis(trimellitimido)phenyl]phthalimide (1) with thionyl chloride followed by a nucleophilic reaction with sodium azide. A novel family of fully aromatic poly(urethane-imide)s with inherent viscosities of 0.19-0.24 dl g⁻¹ were prepared from triimide-dicarbonylazide 3 and various aromatic diols. The polyaddition reactions readily proceeded in desirable yields as one-pot reactions starting from 3 without separately synthesis of the corresponding diisocyanate. All of the resulted polymers were thoroughly characterized by spectroscopic methods and elemental analyses. The poly(urethane-imide)s exhibited an excellent solubility in a variety of polar solvents. Crystallinity nature of the polymers was estimated by means of WXRD. The glass transition temperatures of the polymers determined by DSC method were in the range of 197-219 °C. The 10% weight loss temperatures of the poly(urethane-imide)s from their TGA/DTG curves were found to be in the range of 391-412 °C in nitrogen. The films of the polymers were also prepared by casting the solution.     

Tyrosine-based poly(m-phenyleneethynylene-p-phenyleneethynylene)s. Helix folding and responsiveness to a base

The Sonogashira-Hagihara polymerization of 3′,5′-diiodo-N-α-tert-butoxycarbonyl-l-tyrosine methyl ester (1) and 3′,5′-diiodo-N-α-tert-butoxycarbonyl-O-methyl-l-tyrosine methyl ester (2) with para-diethynylbenzene (3) was carried out to obtain optically active poly(m-phenyleneethynylene-p-phenyleneethynylene)s [poly(1) and poly(2)] with M_n’s ranging from 9900 to 15,000 in 80-87% yields. Poly(1) exhibited intense CD signals in DMSO and THF, but did not in CH₂Cl₂, indicating that it took a predominantly one-handed helical conformation in the former two solvents. On the other hand, there was no evidence for poly(2) to take a helical structure in these solvents. Poly(1) turned the CD sign at 390 nm from plus to minus in DMSO/H₂O = 9/1 (v/v) by the addition of NaOH. Alkaline hydrolysis of ester moieties of poly(1) and poly(2) gave the corresponding polymers having carboxy groups [poly(1a) and poly(2a)]. Poly(1a) and poly(2a) increased the CD intensity by the addition of NaOH.     

Synthesis and electro-optical properties of helical polyacetylenes carrying carbazole and triphenylamine moieties

Novel chiral acetylene monomers bearing carbazole and triphenylamine groups, namely, (S)-3-butyn-2-yl 2-(9-carbazolyl)ethyl carbonate (1) and (S)-3-butyn-2-yl 4-(diphenylamino)benzoate (2) were synthesized, and polymerized with Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃] catalyst to give the corresponding polymers with moderate molecular weights (M_n 13.0 × 10³ and 15.5 × 10³) in good yields (86% and 88%). CD spectroscopic studies revealed that poly(1) and poly(2) took predominantly one-handed helical structure in CHCl₃. The helical structures of poly(1) and poly(2) were very stable against heating and addition of MeOH. The solution of poly(1) and poly(2) emitted fluorescence in 0.52% and 7.2% quantum yields, which were lower than those of the corresponding monomers 1 and 2 (22.5% and 76.5%). The cyclic voltammograms of the polymers indicated that the oxidation potentials of the polymers were lower than those of the monomers. The polymers showed electrochromism and changed the color from pale yellow to pale blue by application of voltage, presumably caused by the formation of polaron at the carbazole and triphenylamine moieties. The onset temperatures of weight loss of poly(1) and poly(2) were 225 and 270 °C under air.     

Synthesis and properties of polyacetylenes carrying N-phenylcarbazole and triphenylamine moieties

Novel acetylene monomers containing N-phenyl-substituted carbazole (Cz) and triphenylamine (TPA) groups, namely, 3-ethynyl-9-phenylcarbazole (1) and p-(N,N-diphenylamino)phenylacetylene (2) were synthesized, and polymerized with several Rh-, W-, and Mo-based catalysts. Poly(1) and poly(2) with high number-average molecular weights (15?500-974?000) were obtained in good yields (77-97%), when [(nbd)RhCl]₂-Et₃N (nbd = norbornadiene) was used as a catalyst. The polymers exhibited UV-vis absorption peaks derived from the Cz and TPA moieties at 250-350 nm and polyacetylene backbone above 350 nm. The UV-vis absorption band edge wavelengths of the polymers were longer than those of the corresponding monomers. Poly(2) exhibited a UV-vis absorption peak at a longer wavelength than poly(1) did, which indicates that poly(2) has main chain conjugation longer than that of poly(1). The molecular weights and photoluminescence quantum yields of the polymers obtained by the polymerization using [(nbd)RhCl]₂-Et₃N were larger than those of the Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃]-based counterparts. The cyclic voltammograms of the polymers indicated that they had clear electrochemical properties; the onset oxidation voltage of poly(1) was higher than those of N-alkyl-substituted Cz derivatives. The polymers showed electrochromism and changed the color from pale yellow to blue by application of voltage, presumably caused by the formation of charged polaron at the Cz and TPA moieties. The temperatures for 5% weight loss of the polymers were around 350-420 °C under air, indicating the high thermal stability.     

Synthesis and properties of polynorbornenes bearing oligomeric siloxane pendant groups

The ring-opening metathesis polymerization (ROMP) of norbornene derivatives 1-5 bearing oligomeric siloxane pendant groups was carried out with Grubbs 1st and 2nd generation, and Grubbs-Hoveyda ruthenium (Ru) catalysts. Monomer 1 gave high-molecular-weight polymers (M_n ca. 27?000-180?000) in high yields (80-100%). Monomers 2-5 also polymerized with Ru carbene catalysts to give high-molecular-weight polymers (M_n ca. 34?000-240?000) in high yields (66-100%). The onset temperatures of weight loss (T₀) of the polymers were 180-250 °C. The glass transition temperatures (T_gs) of poly(1) and poly(2) bearing branched siloxane linkages were near or higher than room temperature (27 and 101 °C). Meanwhile, the T_gs of poly(3)-poly(5) bearing linear siloxane linkages were much lower (−115 to −23 °C), and decreased with increasing length of the siloxane linkages. Poly(1) and poly(2) were hydrogenated completely, which was confirmed by ¹H NMR spectroscopy. The free-standing membranes of poly(1) and poly(2) showed high gas permeability; especially poly(2) is the most permeable to various gases among ROMP-polynorbornene derivatives reported so far.     

New amphiphilic fluorescent CBABC-type pentablock copolymers containing pyrene group by two-step atom transfer radical polymerization (ATRP) and its self-assembled aggregation

A series of novel amphiphilic fluorescent CBABC-type pentablock copolymers (Py-PMMA-PEG4600-PMMA-Py) were prepared from BAB-type amphiphilic triblock copolymer (PMMA-PEG4600-PMMA) as macroinitiator with various contents of 1-(methacryloyloxyethylamino-carboxylmethyl) pyrene (PyMOI) by atom transfer radical polymerization (ATRP) in toluene using CuBr/2,2-bipyridine as catalyst system. Triblock copolymer (PMMA-PEG4600-PMMA) was prepared by ATRP and obtained from Br-PEG4600-Br as macroinitiator with methyl methacrylate in tetrahydrofuran using the same catalyst. The molecular weights of pentablock copolymers which were reinitiated by PMMA-PEG4600-PMMA macroinitiator were calculated from ¹H NMR spectra up to 42,400 gmol⁻¹. The polydispersity of pentablock copolymers obtained from GPC analysis was narrow between 1.10 and 1.38. The crystallinity of triblock copolymer (PMMA-PEG4600-PMMA) was decreased slightly with incorporating PMMA segment. Introducing the bulky pyrene substituent into pentablock copolymer, the melting temperature was not observed and all pentablock copolymers showed amorphous patterns in wide-angle X-ray scattering (WAXS) due to decrease in the degree of crystallinity of polymer chain because of disturbing regular packing. The temperatures at 10% weight loss (Td₁₀), examined by TG analysis, showed values ranging from 265 to 323 °C in nitrogen and 264 to 313 °C in air. Fluorescence spectra of Py-PMMA-PEG4600-PMMA-Py exhibited stronger excimer emission at ca. 480 nm due to the aggregations of pyrene group formed via interaction of the hydrophobic chains. The more content of PyMOI segment in pentablock copolymers can obtain the higher emission intensity ca. 480 nm. When there were higher PyMOI contents (84.9 wt% PyMOI) in pentablock copolymers, they formed larger aggregates (210 nm) in SEM micrographs. On the other hand, while increasing the concentration of the polymer solution in THF, the morphology was changed from spherical (0.1 mg/mL) to chainlike (1.0 mg/mL) aggregates.     

Poly(7-oxanorbornenes) carrying 2,2,6,6-tetramethylpiperidine-1-oxy (TEMPO) radicals: Synthesis and charge/discharge properties

TEMPO-containing 7-oxanorbornene monomers 1-4 (TEMPO = 2,2,6,6-tetramethylpiperidine-1-oxy) were synthesized and polymerized via ring-opening metathesis using a ruthenium carbene catalyst. Monomers 1 and 3 gave polymers with number-average weights of 80?100 and 112?200 in 85 and 96% yields, respectively, whereas monomers 2 and 4 did not provide high molecular weight polymers. Poly(1) and poly(3) were soluble in common solvents including CHCl₃, CH₂Cl₂ and THF, while insoluble in hexane, diethyl ether and MeOH. They were thermally stable up to ca. 240 °C according to the TGA measurements in air. The secondary batteries utilizing the present polymers as cathode-active material demonstrated reversible charge/discharge processes, whose discharge capacities were 107 and 92.8 A h/kg, and displayed excellent high-rate charge and discharge properties. These cells demonstrated excellent cycle life, e.g., the discharge capacities of poly(1) and poly(3) showed less than 10% decrements even after 100 cycles.     

Pd-catalyzed hydrosilylation polymerization of a dihydrosilane with diyne/triyne mixed systems affording crosslinked silylene-divinylene polymers and their properties

Treatment of a dihydrosilane (methylphenylsilane, 1) with mixtures of a diyne (p- or m-diethynylbenzene, 2a or 2b) and a triyne (1,3,5-triethynylbenzene, 3a or B,B′,B″-triethynyl-N,N′,N″-trimethylborazine, 3b; 1:2:3=100:95:5, 100:90:10, 100:80:20) in the presence of Pd-PCy₃ (Cy=cyclohexyl) catalyst gave new crosslinked silylenedivinylene polycarbosilanes. In TGA the resulting crosslinked polymers tended to show higher Td₅ values and higher char yields than the corresponding linear polymers. On the other hand, UV/vis absorption spectra of the crosslinked polymers obtained in the reactions of 2a or 2b with 3a exhibited increased broad peaks around 390 nm for 2a or 360 nm for 2b. Coincidently, their fluorescence spectra showed significant increase of the emission peaks in 400-550 nm. The crosslinked polymer derived from 2a and 3b, however, showed decrease of the absorption peak around 390 nm and profound depression of fluorescence peaks in 400-550 nm.     

Synthesis of amphiphilic triblock copolymer of polystyrene and poly(4-vinylbenzyl glucoside) via TEMPO-mediated living radical polymerization

4-Vinylbenzyl glucoside peracetate 1 was polymerized with α,α′-bis(2′,2′,6′,6′-tetramethyl-1′-piperidinyloxy)-1,4-diethylbenzene 2 in chlorobenzene using (1S)-(+)-10-camphorsulfonic acid anhydrous (CSA) as an accelerator ([1]=0.4 M,[1]/[2]/[CSA]=75/1/1.3) at 125 °C for 5 h. The polymerization afforded poly(4-vinylbenzyl glucoside peracetate) having TEMPO moieties on both sides of the chain ends, 3, with a molecular weight (M_w,SLS) of 8500, a polydispersity index (M_w/M_n) of 1.09, and an average degree of polymerization of the 1 unit (x) of 17. Styrene (St) was polymerized with 3 in chlorobenzene at 125 °C (St/chlorobenzene=1/2, w/w). The polymerization successfully afforded polystyrene-poly(4-vinyl glucoside peracetate)-polystyrene, 4, when the polymerization time was below about 2 h. Polymer 4 with the M_w,SLS of 12,500, 17,900, and 29,400, the compositions (y-x-y) of 20-17-20, 45-17-45, and 100-17-100, and the M_w/M_n of 1.12, 1.14 and 1.17 were modified by deacetylation using sodium methoxide in dry-THF into polystyrene-poly(4-vinyl glucoside peracetate)-polystyrene, 5. The solubility of polymer 5 was examined using a good solvent for polystyrene such as toluene and for the saccharide such as H₂O.