Electrochemical copolymerization of m-toluidine and o-phenylenediamine

Electroactive copolymers of m-toluidine (MT) and o-phenylenediamine (OPD) were prepared electrochemically in aqueous sulfuric acid by potential cycling and characterized with cyclic voltametry, in situ conductivity measurements and FT-IR spectroscopy. The voltammograms of the copolymers exhibit different behavior for different concentrations of OPD in the comonomer feed. At optimum conditions the resulting poly(OPD-co-MT) shows an extended useful potential range of the redox activity as compared to the corresponding homopolymers. The effect of scan rate and pH on the electrochemical activity was studied. The copolymer was electrochemically active even at pH 8.0. The stability of the copolymer film was also tested. The copolymer has a potential region of maximum conductivity different from that of PMT and POPD. The conductivity of the copolymer is between the conductivity of the homopolymers. The vibrational bands at 3122/3450 and 2922/875 cm⁻¹ in the FT-IR spectra of the copolymer indicate the presence of both OPD and MT units, respectively, in the copolymer backbone.     

A correlation of electrochemical and spectroelectrochemical properties of poly(o-toluidine)

A comparative discussion of the electrochemical and spectroelectrochemical properties of poly(o-toluidine) POT, a methyl substituted derivative of polyaniline, PANI, is presented. POT exists in various oxidation states and shows an insulator to conductor transition when doped by electrooxidation. The transformation of the polymer film from its non-conducting leucoemeraldine to its conducting emeraldine state and further on to its again non-conducting pernigraniline form was observed with different techniques including cyclic voltammetry, in situ conductivity measurements and in situ UV-vis and Raman spectroelectrochemical methods. Results reveal that POT shows a good correlation between its electrochemical and spectroelectrochemical properties in its different oxidation states.     

Corrosion protection aspects of electrochemically synthesized poly(o-anisidine-co-o-toluidine) coatings on copper

The poly(o-anisidine-co-o-toluidine) coatings were synthesized on copper substrates by electrochemical copolymerization of o-anisidine with o-toluidine using sodium salicylate as supporting electrolyte. These coatings were characterized by cyclic voltammetry, UV-vis absorption spectroscopy, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and scanning electron microscopy (SEM). The formation of the copolymer with the mixture of monomers in the aqueous sodium salicylate solution was ascertained by a critical comparison of the results obtained with the polymerization of the individual monomers, o-anisidine and o-toluidine, respectively. The corrosion protection aspects of poly(o-anisidine-co-o-toluidine) coatings to copper was investigated in aqueous 3% NaCl solution by potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results of the potentiodynamic polarization measurements and EIS studies showed that the poly(o-anisidine-co-o-toluidine) coatings provided the effective corrosion protection to copper than that of respective homopolymers. The corrosion rate is observed to depend on the feed ratio of o-toluidine used for the synthesis of the copolymer coatings.     

Mobilities of charge carriers in poly(o-methylaniline) and poly(o-methoxyaniline)

Mobilities of charge carriers in poly(o-methylaniline) (PMA) and poly(o-methoxyaniline) (PMOA) films are electrochemically determined over a range of oxidation stages of the polymer films. In the low oxidation region, mobilities of both the polymers are comparable to that of polyaniline (PANI). In the high oxidation region, however, mobility values systematically decrease in the order of PANI > PMA > PMOA, showing that the bulky groups present at the ortho position play a more important role in the high oxidation region. The low mobilities of charge carriers in the high oxidation region explain why PMA and PMOA are less conducting than PANI.     

Spectroelectrochemistry of two-layered composites of polyaniline and poly(o-aminophenol)

Electropolymerization of aniline on poly(o-aminophenol)(POAP)-coated gold and indium-doped tin oxide (ITO)-coated glass electrodes yields polyaniline(PANI)/POAP two-layer composite films, exhibiting reversible redox functions in aqueous acidic solution. The PANI deposition on the POAP-coated electrodes was monitored by cyclic voltammetry (CV) and in situ UV-vis spectroelectrochemistry. CV results show that PANI/POAP composite films exhibit better stability as compared to PANI films during potential cycling in aqueous acidic solutions. Characteristic UV-vis and Raman features of the composite films have been identified and their dependencies on the electrode potential are discussed. They were significantly different from the corresponding spectral characteristics of PANI and POAP films alone.     

Spectroelectrochemistry of aniline-o-aminophenol copolymers

Electroactive copolymers of aniline and o-aminophenol (OAP) with varying concentration ratios prepared by potential cycling in acidic aqueous solutions of the monomers on indium-doped tin oxide (ITO) coated glass and gold electrodes were studied with in situ UV-vis and Raman spectroscopy. Characteristic UV-vis and Raman features have been identified and their dependencies on the electrode potential are discussed. Spectroelectrochemical results reveal the formation of polyaniline-based copolymers at low concentration of OAP in the feed but incorporation of more OAP units into the copolymer with higher concentration of OAP in the comonomer feed. Spectroelectrochemical features are significantly different from those of both homopolymers.     

Photosensitive poly(benzoxazole) based on precursor from diphenyl isophthalate and bis(o-aminophenol)

A new synthetic method for the preparation of poly(benzoxazole) (PBO) precursor, poly(o-hydroxyamide) (7) from bis(o-aminophenol) (5) and diphenyl isophthalate (6) has been developed. Polymer 7 was prepared by the polycondensation of 5 and 6 in 1-methyl-2-pyrrolidinone (NMP) at 185-205 °C. Model reactions were carried out in detail to elucidate appropriate conditions for the formation of 2-hydroxybenzanilide (3) from o-aminophenol (1) and phenyl benzoate (2). The photosensitive (PBO) precursor based on polymer 7 containing a 22% of benzoxazole unit and 30 wt% 1-{1,1-bis[4-(2-diazo-1-(2H)naphthalenone-5-sulfonyloxy)phenyl]ethyl}-4-{1-[4-(2-diazo-1(2H)naphthalenone-5-sulfonyloxy)phenyl]methylethyl}benzene (S-DNQ) showed a sensitivity of 110 mJ cm⁻² and a contrast of 5.0 when it was exposed to 436 nm light followed by developing with a 2.38 wt% aqueous tetramethylammonium hydroxide solution at room temperature. A fine positive image featuring 8 μm line and space patterns was observed on the film of the photoresist exposed to 200 mJ cm⁻² of UV-light at 436 nm by the contact mode.     

In situ gelling aqueous solutions of pH- and temperature-sensitive poly(ester amino urethane)s

A series of novel pH- and temperature-sensitive multiblock poly(ester amino urethane)s were synthesized. The copolymers were characterized by ¹H NMR, FT-IR and GPC. In the multiblock copolymers, the tertiary amino groups of the poly(amino urethane) segments act as pH-responsive moieties, while the PCL-PEG-PCL blocks act as biodegradable and temperature-sensitive segments. At a relatively high pH (7.0 or above), the multiblock copolymer aqueous solution showed a sol-to-gel-to-aggregation transition with increasing temperature. In contrast, at a lower pH (below 7.0), the polymer solution always existed as a sol state within the experimental temperature range. The gel window covers the physiological conditions. After subcutaneous injection of the 20 wt% multiblock copolymer solutions into mice, polymeric hydrogels were formed in situ in a short time. The in vitro release of an anticancer drug, paclitaxel, persisted over 1 month under physiological conditions.     

Corrosion protective poly(o-ethoxyaniline) coatings on copper

Poly(o-ethoxyaniline) (POEA) coatings were synthesized on copper (Cu) by electrochemical polymerization of o-ethoxyaniline in aqueous salicylate solution by using cyclic voltammetry. These coatings were characterized by cyclic voltammetry, UV-vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The performance of POEA as protective coating against corrosion of Cu in aqueous 3% NaCl was assessed by the potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results of the potentiodynamic polarization and EIS studies demonstrate that the POEA coating has ability to protect the Cu against corrosion. The corrosion potential was about 0.330 V versus SCE more positive in aqueous 3% NaCl for the POEA coated Cu than that of uncoated Cu and reduces the corrosion rate of Cu almost by a factor of 140.     

Electrochemical preparation and kinetic study of poly(o-tolidine) in aqueous medium

Poly(o-tolidine), PoT, film was prepared by electrochemical oxidation of the monomer, oT, in 0.1 M HCl + 0.1 M KClO₄. The presence of KClO₄ in the formation medium was found to be essential for the electropolymerization process to proceed. Increasing the upper potential limit up to +1.5 V, instead of +1.0 V, leads to appearance of a new anodic peak at +1.36 V and enhancement of the polymer formation of PoT without changing the film structure. The electrochemical behavior of the formed polymer films was investigated in 1.0 M HClO₄. The kinetic parameters were calculated from the values of the charge consumed during the electropolymerization process. The rate of the polymerization reaction was found to depend on the concentration of the monomer rather than the electrolyte. The polymerization rate is first order with respect to the monomer concentration and zero order with respect to the electrolyte. The electrolyte plays no active role in the kinetics of the electropolymerization process and its role is most likely limited to polymer doping.     

Inhibition of steel corrosion by electrosynthesized poly(o-anisidine)-dodecylbenzenesulfonate coatings

Poly(o-anisidine)-dodecylbenzenesulfonate (POA-DBSA) coatings were synthesized on stainless steel from aqueous solution containing o-anisidine and dodecylbenzene sulfonic acid by using cyclic voltammetry. These coatings were characterized by Fourier transform infrared spectroscopy (FTIR), UV-vis absorption spectroscopy, scanning electron microscopy (SEM) and cyclic voltammetry (CV). Corrosion tests of these coatings were carried out in aqueous 3% NaCl solution by using open circuit potential (OCP) measurements, potentiodynamic polarization technique, cyclic potentiodynamic polarization measurements and electrochemical impedance spectroscopy (EIS). The results reveal that POA-DBSA acts as a corrosion protective coating on steel and reduces the corrosion rate (CR) of steel almost by a factor of 14.5.     

Methanol electrooxidation on platinum microparticles electrodeposited on poly (o-methoxyaniline) films

In this paper we have studied the electrooxidation of methanol on electrodes obtained through the electrodeposition of platinum microparticles on poly (o-methoxyaniline) films. The dependence of the electroactivity on the electrodes preparation parameters has been detailed. It has been shown that the concentration of the monomer during the formation of the polymeric films influences the rate of polymer growth and the electrocatalytic activity. A maximum methanol electrooxidation peak current has been observed for polymers grown to an anodic voltammetric charge of approximately 75 mC cm⁻². It has been observed that the electroactivity increases when the platinum deposition is carried out in several steps instead of a single potential electrolysis. The conditions that favour a slower deposition process, i.e., smaller H₂PtCl₆ concentrations and smaller electrodeposition overpotential, lead to an enhancement of the methanol electrooxidation currents. This enhancement is attributed to an increase in the platinum surface area as a consequence of a decrease in the platinum particle size.     

Potentiodynamic deposition of poly (o-anisidine-co-metanilic acid) on mild steel and its application as corrosion inhibitor

For the first time, poly (o-anisidine-co-metanilic acid) (PASM) was deposited on mild steel substrate by electrochemical polymerization of o-anisidine and metanilic acid monomers in aqueous solution of 0.1 M H₂SO₄. The electrochemical polymerization of o-anisidine takes place in the presence of metanilic acid monomer and uniform, strongly adherent coating was obtained on the substrate. The electroactivity of copolymer was studied by cyclic voltammetry and AC impedance techniques. There is an increasing anodic current due to oxidation of metanilic acid monomer at the surface of the electrode when the applied potential is cycled from −0.2 V to 0.8 V. These deposits were characterized by Fourier transform infrared (FTIR) spectroscopy, UV-vis and TG/DTA techniques. The effect of various concentrations of PASM copolymer solution in acid rain corrosive media has been studied through potentiodynamic polarization, AC impedance and I-E curve methods. The soluble form of polymeric solution provided better anti-corrosive behavior in artificial acid rain solution.     

Synthesis of electrically conducting copolymers of aniline with o/m-amino benzoic acid by an inverse emulsion pathway

Copolymers of aniline and ortho/meta-amino benzoic acid were synthesized by chemical polymerization using an inverse emulsion pathway. The copolymers are soluble in organic solvents, and the solubility increases with the amino benzoic acid content in the feed. The reaction conditions were optimized with emphasis on high yield and relatively good conductivity (2.5×10⁻¹ S cm⁻¹). The copolymers were characterized by a number of techniques including UV-vis, FT-IR, FT-Raman, EPR and NMR spectroscopy, thermal analysis, SEM and conductivity. The influence of the carboxylic acid group ring substituent on the copolymers is investigated. The spectral studies reveal that the amino benzoic acid groups restrict the conjugation along the polymer chain. The SEM micrographs of the copolymers reveal regions of amorphous and crystalline domain. Thermal studies indicate a marginally higher thermal stability for poly(aniline-co-m-amino benzoic acid) compared to poly(aniline-co-o-amino benzoic acid).     

In situ transmission FTIR spectroelectrochemistry: A new technique for studying lithium batteries

In situ transmission FTIR spectra are measured during the electrochemical insertion of lithium into phospho-olivine FePO₄. The spectroelectrochemical cell consists of a composite FePO₄ cathode, a lithium metal anode, and an electrolyte of 1 M LiPF₆ in a 1:1 mixture of ethylene carbonate and diethyl carbonate (EC-DEC). Bands belonging to the electrolyte and cathode are identified in the infrared spectra of the in situ cells. The antisymmetric PO₄³⁻ bending vibrations (ν₄) are used to monitor Li⁺ insertion into FePO₄. Discharging produces spectral changes that are consistent with the formation of phospho-olivine LiFePO₄, yet the electrolyte bands are not affected by the discharging process. The in situ infrared experiments confirm the two-phase mechanism for lithium insertion into FePO₄. Moreover, the experiments demonstrate the ability to collect in situ transmission FTIR spectra of functioning electrode materials in lithium batteries. Unfortunately, lithium plating occurs on the optical window when the Li//FePO₄ half-cells are charged. The use of an intercalation anode such as graphite could alleviate this problem; however, this avenue of research is not explored in this study.     

In situ synthesis and characterization of poly(2,5-benzoxazole)/multiwalled carbon nanotubes composites

This article reports the synthesis of poly(2,5-benzoxazole)/multiwalled carbon nanotubes (ABPBO/MWNT) composites by in situ polycondensation and their chemical and physical properties. The functional groups yielded from the surface modification of MWNTs by hydrochloric acids have been demonstrated to participate in the polymerization and thus led to the composites with homogenous dispersion of carbon nanotubes. The chemical structures and morphology of the afforded polymer composites have been fully characterized by FTIR, WAXD, UV-vis, TGA and SEM. The ABPBO/MWNT composites exhibit excellent thermal stability and greatly improved mechanical properties. The tensile modulus and tensile strength of the composites are 47% and 83%, respectively, higher than those of the polymer matrix. The dielectric constant of the composites is also significantly enhanced from 4 of the polymer matrix to 65 with the incorporation of 5 wt% MWNTs.     

In situ evaluation of structural changes in poly(ester-urethanes) during shape-memory cycles

The relationship between shape-memory behavior and structure was studied using three series of poly(ester-urethanes) with varying amounts of hard segment. The materials were designed to display a three-phase structure consisting of a disperse phase of crystallites and hard domains embedded in an amorphous matrix based on soft segment. Structure and thermal properties of the resultant materials were investigated using techniques such as modulated differential scanning calorimetry (MDSC), dynamic mechanical analysis (DMA) and small angle X-ray scattering (SAXS). The results revealed morphological changes in the materials during a low temperature shape-memory cycle. To study shape recovery, a deformed specimen was evaluated on a heating stage mounted at the SAXS beamline. Furthermore, to study the effect of temperature during recovery, the specimens were subjected to different thermo-cycles. Under each set of conditions, the phase morphology and composition were investigated. Temporary shape was stored by the metastable structure formed during deformation. The recovery was triggered by the melting of crystallites and hydrogen bonding between hard domains. The recovery process was divided into three stages. Bulk incompatibility and entropic recovery determined the final polyurethane morphology.     

Synthesis and characterization of bionanocomposites of poly(lactic acid) and TiO2 nanowires by in situ polymerization

Bionanocomposites from biopolymers and inorganic nanoparticles are of great interest for packaging materials due to their enhanced physical, thermal, mechanical, and processing characteristics. In this study, poly(lactic acid) (PLA) nanocomposites with covalent bonding between TiO₂ nanowire surface and PLA chains were synthesized through in situ melt polycondensation. Molecular weight, structure, morphology, and thermal properties were characterized. Fourier transform infrared spectroscopy confirmed that PLA chains were covalently grafted onto TiO₂ nanowire surface. Transmission electron microscopy images also revealed clearly a third phase presence on the nanowires after the grafting process. Those grafted PLA chains exhibited significantly increased glass transition temperature and thermal stability, compared with pure PLA. The weight-average molecular weight of PLA/2% TiO₂ nanowire bulk nanocomposites increased by 66% compared with that of pure PLA. The electron microscopy results showed that strong interfacial interaction and homogeneous distribution were achieved between inorganic nanowires and organic PLA matrix in the bulk nanocomposites. The PLA matrix in bulk nanocomposites exhibited elevated glass transition temperature and decreased crystallization ability as the TiO₂ nanowire concentrations were increased from 0 to 2%.     

Electrochemical synthesis and corrosion performance of poly(pyrrole-co-o-anisidine)

The electrochemical synthesis of poly(o-anisidine) homopolymer and its copolymerization with pyrrole have been investigated on mild steel. The copolymer films have been synthesized from aqueous oxalic acid solutions containing different ratios of monomer concentrations: pyrrole:o-anisidine, 9:1, 8:2, 6:4, 1:1. The characterization of polymer films were achieved with FT-IR, UV–visible spectroscopy and cyclic voltammetry techniques. The electrochemical synthesis of homogeneous-stable poly(o-anisidine) film with desired thickness was very difficult on steel surface. Therefore its copolymer with pyrrole has been studied to obtain a polymer film, which could be synthesized easily and posses the good physical–chemical properties of anisidine. The kinetics and rate of copolymer film growth were strongly related to monomer feed ratio. The introduction of pyrrole unit into synthesis solution increased the rate of polymerization and the substrate surface became covered with polymer film soon, while this process required longer periods in single o-anisidine containing solution. The protective behavior of coatings has been investigated against steel corrosion in 3.5% NaCl solution. For this aim electrochemical impedance spectroscopy (EIS) and anodic polarization curves were utilized. The synthesized poly(o-anisidine) coating exhibited significant protection efficiency against mild steel corrosion. It was shown that 6:4 ratio of pyrrole and anisidine solution gave the most stable and corrosion protective copolymer coating.     

In situ Raman spectroelectrochemical study of redox processes at poly(Toluidine blue) modified electrode

Electrooxidation of hydroquinone and ascorbic acid at a gold electrode modified with electropolymerized layer of phenothiazine dye Toluidine blue (PTB) has been studied with the use of in situ Raman spectroelectrochemical technique, surface enhanced resonance Raman spectroscopy (SERRS). It was shown that the redox state of PTB at any electrode potential can be determined in pH 1.0 and 4.0 solutions following specific changes in Raman spectra of these modifier layers. Electrooxidation of hydroquinone at PTB modified electrode in pH 1.0 solution, and of ascorbic acid in pH 4.0 solution, proceed without any detectable changes in a net redox state of modifier layers. It has been concluded that, under the conditions studied, both anodic oxidation processes occur most probably at the modifier/electrolyte interface rather than within the modifier film, as opposed to electrooxidation of same species at polyaniline modified electrodes studied earlier.