A 56 mW Continuous-Time Quadrature Cascaded Σ∆ Modulator With 77 dB DR in a Near Zero-IF 20 MHz Band

A quadrature cascaded modulator with continuous-time loop filters is presented for a digital multi-stream FM radio receiver. The ADC achieves a dynamic range of 77 dB and 20 MHz bandwidth centered on an intermediate frequency of 10.5 MHz and is sampling at 340 MHz. The cascaded modulator comprises programmable analog second-order quadrature filters and a digital quadrature noise cancellation filter. The 0.5 chip in 90 nm CMOS consumes 56 mW from a 1.2 V supply.     

A 2.2-mW CMOS bandpass continuous-time multibit /spl Delta/-/spl Sigma/ ADC with 68 dB of dynamic range and 1-MHz bandwidth for wireless applications

A delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter featuring 68-dB dynamic range and 64-dB signal-to-noise ratio in a 1-MHz bandwidth centered at an intermediate frequency of 2 MHz with a 48-MHz sample rate is reported. A second-order continuous-time modulator employing 4-bit quantization is used to achieve this performance with 2.2 mW of power consumption from a 1.8-V supply. The modulator including references occupies 0.36 mm/sup 2/ of die area and is implemented in a 0.18-/spl mu/m five-metal single-poly digital CMOS process.     

A 70-mW 300-MHz CMOS continuous-time /spl Sigma//spl Delta/ ADC with 15-MHz bandwidth and 11 bits of resolution

A wide-bandwidth continuous-time sigma-delta ADC is implemented in a 0.13-/spl mu/m CMOS. The circuit is targeted for wide-bandwidth applications such as video or wireless base-stations. The active blocks are composed of regular threshold voltage devices only. The fourth-order architecture uses an OpAmp-RC-based loop filter and a 4-bit internal quantizer operated at 300-MHz clock frequency. The converter achieves a dynamic range of 11 bits over a bandwidth of 15 MHz. The power dissipation is 70 mW from a 1.5-V supply.     

A third-order /spl Sigma//spl Delta/ modulator in 0.18-/spl mu/m CMOS with calibrated mixed-mode integrators

This paper describes a third-order sigma-delta (/spl Sigma//spl Delta/) modulator that is designed and implemented in 0.18-/spl mu/m CMOS process. In order to increase the dynamic range, this modulator takes advantage of mixed-mode integrators that consist of analog and digital integrators. A calibration technique is applied to the digital integrator to mitigate mismatch between analog and digital paths. It is shown that the presented modulator architecture can achieve a 12-dB better dynamic range than conventional structures with the same oversampling ratio (OSR). The experimental prototype chip achieves a 76-dB dynamic range for a 200-kHz signal bandwidth and a 55-dB dynamic range for a 5-MHz signal bandwidth. It dissipates 4 mW from 1.8-V supply voltages and occupies 0.7-mm/sup 2/ silicon area.     

A 14-bit, 10-Msamples/s D/A converter using multibit /spl Sigma//spl Delta/ modulation

A 14-bit digital-to-analog converter based on a fourth-order multibit sigma-delta modulator is described. The digital modulator is pipelined to minimize both its power dissipation and design complexity. The 6-bit output of this modulator is converted to analog using 64 current-steering cells that are continuously calibrated to a reference current. This converter achieves 85-dB dynamic range at 5-MHz signal bandwidth, with an oversampling ratio of 12. The chip was fabricated in a 0.5-/spl mu/m CMOS technology and operates from a single 2.5-V supply.     

A high-frequency and high-resolution fourth-order /spl Sigma//spl Delta/ A/D converter in BiCMOS technology

A high-performance cascaded sigma-delta modulator is presented. It has a new three-stage fourth-order topology and provides functionally a maximum signal to quantization noise ratio of 16 bits and 16.5-bit dynamic range with an oversampling ratio of only 32. This modulator is implemented with fully differential switch-capacitor circuits and is manufactured in a 2-/spl mu/m BiCMOS process. The converter, operated from +/-2.5 V power supply, +/-1.25 V reference voltage and oversampling clock of 48 MHz, achieves 97 dB resolution at a Nyquist conversion rate of 1.5 MHz after comb-filtering decimation. The power consumption of the converter is 180 mW.<>     

Cascaded Complex ADCs With Adaptive Digital Calibration for $I/Q$ Mismatch

A complex analog-to-digital converter (ADC) intended for digital intermediate frequency (IF) receiver applications digitizes analog signals at IFs with excellent power/bandwidth efficiency. However, it is vulnerable to mismatches between its in-phase and quadrature (I/Q) paths that can dramatically degrade its performance. The proposed solution mitigates I/Q mismatch effects using a complex sigma-delta (SigmaDelta) modulator cascaded with 9-bit pipeline converters in each of the I and Q paths. The quantization noise of the first stage complex modulator is eliminated using an adaptive scheme to calibrate finite-impulse response digital filters in the digital noise-cancellation logic block. Although low-pass SigmaDelta cascade ADCs are widely used because of their inherent stability and high-order noise shaping, the complex bandpass cascade architecture introduced herein maintains these advantages and doubles the noise shaping bandwidth. Digital calibration also reduces the effects of analog circuit limitations such as finite operational amplifier gain, which enables high performance and low power consumption with high-speed deep-submicrometer CMOS technology. Behavioral simulations of the complex SigmaDelta/pipeline cascade bandpass ADC using the adaptive digital calibration algorithm predict a signal-to-noise ratio (SNR) of 78 dB over a 20-MHz signal bandwidth at a sampling rate of 160 MHz in the presence of a 1% I/Q mismatch.     

A 64-MHz clock-rate /spl Sigma//spl Delta/ ADC with 88-dB SNDR and -105-dB IM3 distortion at a 1.5-MHz signal frequency

A 64-MHz clock rate sigma-delta (/spl Sigma//spl Delta/) analog-to-digital converter (ADC) with -105-dB intermodulation distortion (IMD) at a 1.5-MHz signal frequency is reported. A linear replica bridge sampling network enables the ADC to achieve high linearity for high signal frequencies. Operating at an oversampling ratio of 29, a 2-1-1 cascade with a 2-b quantizer in the last stage reduces the quantization noise level well below that of the thermal noise. The measured signal-to-noise and distortion ratio (SNDR) in 1.1-MHz bandwidth is 88 dB, and the spurious-free-dynamic-range (SFDR) is 106 dB. The modulator and reference buffers occupy a 2.6-mm/sup 2/ die area and have been implemented with thick oxide devices, with minimum channel length of 0.35 /spl mu/m, in a dual-gate 0.18-/spl mu/m 1.8-V single-poly five-metal (SP5M) digital CMOS process. The power consumed by the ADC is 230 mW, including the decimation filters.     

LMS-Based Noise Leakage Calibration of Cascaded Continuous-Time Modulators

In cascaded $DeltaSigma$ modulators (DSMs), the quantization noise of the earlier stage leaks to the output unless completely cancelled by the digital noise cancellation filter (NCF). The noise leakage is worse in the continuous-time (CT) implementation due to the poorly controlled time constant of the analog loop filter. A parameter-based continuous-time to discrete-time transform is developed to get an exact digital NCF, and the analog filter time constant is calibrated to match with the digital NCF. A binary pulse tone is injected into the quantizer to detect the filter time-constant error, and eliminated by zero-forcing its residual power based on the adaptive least-mean-square (LMS) algorithm. A 2-1-1 cascaded CT-DSM prototype in 0.18-$mu{hbox {m}}$ CMOS demonstrates that the spectral density of the leaked noise is lower than 10 ${rm nV}/surd{hbox {Hz}}$ after the capacitors in the Gm-C loop filters are trimmed with 1.1% step. With a 1- ${rm V}_{rm pp}$ full-scale input, it achieves a dynamic range of 68$~$ dB within 18-MHz bandwidth at an over-sampling ratio of 10. The analog core and the digital logic occupy 1.27 ${hbox {mm}}^{2}$, and consume 230 mW at 1.8 V.      

An agile ISM band frequency synthesizer with built-in GMSK datamodulation

In this paper, a high-resolution fractional-N RF frequency synthesizer is presented which is controlled by a fourth-order digital sigma-delta modulator. The high resolution allows the synthesizer to be digitally modulated directly at RF. A simplified digital filter which makes use of sigma-delta quantized tap coefficients is included which provides built-in GMSK pulse shaping for data transmission. Quantization of the tap coefficients to single-bit values not only simplifies the filter architecture, but the fourth-order digital sigma-delta modulator as well. The synthesizer makes extensive use of custom VLSI, with only a simple off-chip loop filter and VCO required. The synthesizer operates from a single 3-V supply, and has low power consumption. Phase noise levels are less than -90 dBc/Hz at frequency offsets within the loop bandwidth. Spurious components are less than -90 dBc/Hz over a 19.6-MHz tuning range     

A 20-mW 640-MHz CMOS Continuous-Time Σ∆ ADC With 20-MHz Signal Bandwidth, 80-dB Dynamic Range and 12-bit ENOB

A wide bandwidth continuous-time sigma-delta ADC, operating between 20 and 40 MS/s output data rate, is implemented in 130-nm CMOS. The circuit is targeted for applications that demand high bandwidth, high resolution, and low power, such as wireless and wireline communications, medical imaging, video, and instrumentation. The third-order continuous-time SigmaDelta modulator comprises a third-order RC operational-amplifier-based loop filter and 4-bit internal quantizer operating at 640 MHz. A 400-fs rms jitter LC PLL with 450-kHz bandwidth is integrated, generating the low-jitter clock for the jitter-sensitive continuous-time SigmaDelta ADC from a single-ended input clock between 13.5 and 40 MHz. To reduce clock jitter sensitivity, nonreturn-to-zero (NRZ) DAC pulse shaping is used. The excess loop delay is set to half the sampling period of the quantizer and the degradation of modulator stability due to excess loop delay is avoided with a new architecture. The SigmaDelta ADC achieves 76-dB SNR, -78-dB THD, and a 74-dB SNDR or 12 ENOB over a 20-MHz signal band at an OSR of 16. The power consumption of the CT SigmaDelta modulator itself is 20 mW and in total the ADC dissipates 58 mW from the 1.2-V supply     

A time-interleaved continuous-time /spl Delta//spl Sigma/ modulator with 20-MHz signal bandwidth

This paper presents the first implementation results for a time-interleaved continuous-time /spl Delta//spl Sigma/ modulator. The derivation of the time-interleaved continuous-time /spl Delta//spl Sigma/ modulator from a discrete-time /spl Delta//spl Sigma/ modulator is presented. With various simplifications, the resulting modulator has only a single path of integrators, making it robust to DC offsets. A time-interleaved by 2 continuous-time third-order low-pass /spl Delta//spl Sigma/ modulator is designed in a 0.18-/spl mu/m CMOS technology with an oversampling ratio of 5 at sampling frequencies of 100 and 200 MHz. Experimental results show that a signal-to-noise-plus-distortion ratio (SNDR) of 57 dB and a dynamic range of 60 dB are obtained with an input bandwidth of 10 MHz, and an SNDR of 49 dB with a dynamic range of 55 dB is attained with an input bandwidth of 20 MHz. The power consumption is 101 and 103 mW, respectively.     

A 16-b 160-kHz CMOS A/D converter using sigma-delta modulation

The design and measured performance of a third-order sigma-delta analog-to-digital (A/D) converter sampling at 10.24 MHz that achieves a 91-dB signal-to-noise-plus-distortion ratio (RMS/RMS) with a 160-kHz output rate are discussed. The converter consists of three cascaded first-order sigma-delta modulators and a fourth-order comb decimation filter. A special autozeroed integrator having low pole error is required to achieve the 10.24-MHz sampling rate and high S/N. The modulator is implemented with fully differential switched-capacitor circuits and is manufactured using a 1.5-μm double-metal double-poly CMOS process     

A Multi-Mode Sigma-Delta ADC for GSM/WCDMA/WLAN Applications

The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. In multi-standard design, sigma-delta based ADC is one of the most popular choices. To this end, in this paper we present cascaded 2-2-2 reconfigurable sigma-delta modulator that can handle GSM, WCDMA and WLAN standards. The modulator makes use of a low-distortion swing suppression topology which is highly suitable for wide band applications. In GSM mode, only the first stage (2nd order ∑-Δ ADC) is used to achieve a peak SNDR of 88dB with over-sampling ratio of 160 for a bandwidth of 200KHz and for WCDMA mode a 2-2 cascaded structure (4th order) is turned on with 1-bit in the first stage and 2-bit in the second stage to achieve 74 dB peak SNDR with over-sampling ratio of 16 for a bandwidth of 2MHz. Finally, a 2-2-2 cascaded MASH architecture with 4-bit in the last stage is proposed to achieve a peak SNDR of 58dB for WLAN for a bandwidth of 20MHz. The novelty lies in the fact that unused blocks of second and third stages can be made inactive to achieve low power consumption. The modulator is designed in TSMC 0.18um CMOS technology and operates at 1.8 supply voltage.     

Electromechanical-Filter-Based Bandpass Sigma–Delta Modulator

This brief proposes an electromechanical-filter-based continuous-time (CT) bandpass (BP) sigma-delta modulator for wideband digitization at high intermediate frequency (> 70 MHz). Both the mechanically coupled microelectromechanical system and the longitudinally coupled surface acoustic wave (SAW) filters can be employed as loop filters. The advantages of the electromechanical filter are its low power consumption and accurate center frequency without the need for tuning. As a proof of concept, a fourth-order BP sigma-delta modulator is demonstrated with a 110-MHz SAW filter. Realized in a 0.35- mum SiGe heterojunction-bipolar-transistor bipolar complimentary metal-oxide-semiconductor technology, the prototype chip is clocked at 440 MHz and achieves 65-dB DR and 60-dB SNDR over 1 MHz, as well as 58-dB DR and 53-dB SNDR over the 3.84-MHz signal band. The total power consumption is 57 mW under a 3-V supply.     

A CMOS oversampling bandpass cascaded D/A converter with digital FIR and current-mode semi-digital filtering

An oversampling bandpass digital-to-analog converter has been designed so as to eliminate the carrier leak and in-band SNR degradation that accompany I and Q channel mismatch in wireless transmitters. The converter combines a cascaded noise-shaping sigma-delta (/spl Sigma//spl Delta/) modulator with digital finite impulse response (FIR) and mixed-signal semi-digital filters that attenuate out-of-band quantization noise. The performance of the converter in the presence of current source mismatch has been improved through the use of bandpass data weighted averaging. An experimental prototype of the converter, integrated in a 0.25-/spl mu/m CMOS technology, provides 83 dB of dynamic range for a 6.25-MHz signal band centered at 50 MHz, and suppresses out-of-band quantization noise by 38 dB.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.     

A 2.5-V 14-bit, 180-mW Cascaded Σ∆ ADC for ADSL2+ Application

This paper presents a sigma-delta (SigmaDelta) analog-to-digital converter (ADC) for the extended bandwidth asymmetric digital subscriber line application. The core of the ADC is a cascaded 2-1-1 SigmaDelta modulator that employs a resonator-based topology in the first stage, three tri-level quantizers, and two different pairs of reference voltages. As shown in the experimental result, for a 2.2-MHz signal bandwidth, the ADC achieves a dynamic range of 86 d 15 and a peak signal-to-noise and distortion ratio of 78 dB with an oversampling ratio of 16. It is implemented in a 0.25-mum CMOS technology, in a 2.8 mm² active area including decimation filter and reference voltage buffers, and dissipates 180 mW from a 2.5-V power supply.     

An Injection-Locked Frequency-Tracking Σ∆ Direct Digital Frequency Synthesizer

A bandpass (BP) sigma-delta modulator (SigmaDeltaM)-based direct digital frequency synthesizer (DDS) architecture is presented. The DDS output is passed through a single-bit, second-order BPSigmaDeltaM, shaping quantization noise out of the signal band. The single-bit BPSigmaDeltaM is then injection locked to an LC-tank oscillator, which provides a tracking BP filter response within its locking range, suppressing the BPSigmaDeltaM out of band quantization noise. The instantaneous digital frequency control word input of the DDS is used to tune the noise shaper center frequency, achieving up to 20% tuning range around the fundamental. The BPSigmaDeltaM-based synthesizer is fabricated in a 0.25-mum digital CMOS process with four layers of metal. With a second-order BP noise shaper and a 44-MHz LC tank oscillator, an SFDR of 73 dB at a 2-MHz bandwidth and phase noise lower than -105 dBc/Hz at a 10-kHz offset is achieved     

A Case Study on a 2-1-1 Cascaded Continuous-Time Sigma-Delta Modulator

This paper intends to give an insight into the potentials and tradeoffs when designing cascaded, continuous-time (CT) sigma-delta modulators. Therefore, a case study is presented considering the implementation of a 2-1-1 CT modulator. The nonideal behavior is regarded in detail and an automatic gain-error cancellation is presented. Finally, a circuit board implementation is presented, which has been chosen to verify the automatic error correction. It turns out that despite a more critical behavior than in the discrete-time (DT) case, cascaded CT modulators have the potential, to realize high bandwidth, high resolution analog-to-digital (A/D) converters in future integrated designs.