Effect of n-Butane and propane on performance and emission characteristics of an SI engine operated with DME-blended LPG fuel

In this study, a spark ignition engine operated with DME-blended LPG fuel was studied experimentally. In particular, the effect of n-Butane and propane on performance, emissions characteristics (including hydrocarbon, CO, and NOx), and the combustion stability of an SI engine fuelled with DME-blended LPG fuel were examined. Four kinds of test fuel with different blend ratios of n-Butane, propane, and DME were used. The percentage of DME in the fuel blend was 20% by mass.The results showed that stable engine operation was possible for a wide range of engine loads with propane containing LPG/DME-blended fuel rather than n-Butane containing LPG/DME-blended fuel since the octane number of propane is higher than that of n-Butane. Also, engine power output, break specific fuel consumption (BSFC), and combustion stability when operating with propane containing DME-blended fuel were comparable to those values in case of pure LPG fuel operation. Engine power output was decreased and BSFC was increased with n-Butane containing DME-blended fuel due to the lower energy density of DME. To examine the effect of n-Butane and propane on emissions and fuel economy in an actual vehicle, a vehicle was tested during an FTP-75 cycle. Through the emission and fuel economy test in the FTP-75 cycle, we conclude that the differences in emission level and fuel economy were not significant according to the blend of n-Butane, propane, and DME.Considering the experimental results from the engine bench and the actual vehicle, the 20% content of DME-blended fuel, regardless of LPG type, can be used as an alternative fuel for LPG.     

Combustion characteristics of a direct-injection engine fueled with natural gas-hydrogen blends under different ignition timings

In this paper, combustion characteristics of a direct-injection spark-ignited engine fueled with natural gas-hydrogen blends under various ignition timings and lean mixture condition were investigated. The results show that the ignition timing has significant influence on engine performance, combustion and emissions. The time intervals between the end of fuel injection and ignition timing are very sensitive to direct-injection gas engine combustion. The turbulence in combustion chamber generated by the fuel jet maintains high and relatively strong mixture stratification is presented when decreasing the time intervals between the end of injection and the ignition timing, giving fast burning rate, high brake mean effective pressure, high thermal efficiency and short combustion durations. For specific ignition timing, the brake mean effective pressure and the effective thermal efficiency increase and combustion durations decrease with the increase of hydrogen fraction in natural gas. Exhaust HC concentration decreases and exhaust NO_x concentration increase with advancing the ignition timing while the exhaust CO gives little variation under various ignition timings.     

Performance and exhaust emission characteristics of a spark ignition engine using ethanol and ethanol-reformed gas

Since ethanol is a renewable source of energy and has lower carbon dioxide (CO₂) emissions than gasoline, ethanol produced from biomass is expected to be used more frequently as an alternative fuel. It is recognized that for spark ignition (SI) engines, ethanol has the advantages of high octane and high combustion speed and the disadvantage of ignition difficulties at low temperatures. An additional disadvantage is that ethanol may cause extra wear and corrosion of electric fuel pumps. On-board hydrogen production out of ethanol is an alternative plan.Ethanol has been used in Brazil as a passenger vehicle fuel since 1979, and more than six million vehicles on US highways are flexible fuel vehicles (FFVs). These vehicles can operate on E85 - a blend of 85% ethanol and 15% gasoline.This paper investigates the influence of ethanol fuel on SI engine performance, thermal efficiency and emissions. The combustion characteristics of hydrogen enriched gaseous fuel made from ethanol are also examined.Ethanol has excellent anti-knock qualities due to its high octane number and a high latent heat of evaporation, which makes the temperature of the intake manifold lower. In addition to the effect of latent heat of evaporation, the difference in combustion products compared with gasoline further decreases combustion temperature, thereby reducing cooling heat loss. Reductions in CO₂, nitrogen oxide (NOx), and total hydrocarbons (THC) combustion products for ethanol vs. gasoline are described.     

A study of natural gas/DME combustion in HCCI engines using CFD with detailed chemical kinetics

Combustion characteristics of natural gas and dimethyl ether (DME) mixture in a homogeneous charge compression ignition (HCCI) engine were studied numerically. Detailed chemical kinetics with 83 species and 360 reactions was used with an engine CFD code to simulate the combustion process. Operating conditions with different fuel compositions were simulated. Combustion, nitrogen oxides emissions and effects of fuel compositions on engine operating limits were well predicted by the present model. Chemical kinetics analysis indicated that ignition was achieved by DME oxidation which, in turn, induced combustion of natural gas. Low-temperature heat release is more pronounced as the amount of DME increases. Engine operations become unstable as the excess air ratio of natural gas is reduced near 2. The model also captures the HCCI features of low-combustion temperature and low-nitrogen oxides emissions for the alternative fuels used in this study.     

Diesel and rapeseed methyl ester (RME) pilot fuels for hydrogen and natural gas dual-fuel combustion in compression-ignition engines

This paper presents experimental results of rapeseed methyl ester (RME) and diesel fuel used separately as pilot fuels for dual-fuel compression-ignition (CI) engine operation with hydrogen gas and natural gas (the two gaseous fuels are tested separately). During hydrogen dual-fuel operation with both pilot fuels, thermal efficiencies are generally maintained. Hydrogen dual-fuel CI engine operation with both pilot fuels increases NO_x emissions, while smoke, unburnt HC and CO levels remain relatively unchanged compared with normal CI engine operation. During hydrogen dual-fuel operation with both pilot fuels, high flame propagation speeds in addition to slightly increased ignition delay result in higher pressure-rise rates, increased emissions of NO_x and peak pressure values compared with normal CI engine operation. During natural gas dual-fuel operation with both pilot fuels, comparatively higher unburnt HC and CO emissions are recorded compared with normal CI engine operation at low and intermediate engine loads which are due to lower combustion efficiencies and correspond to lower thermal efficiencies. This could be due to the pilot fuel failing to ignite the natural gas-air charge on a significant scale. During dual-fuel operation with both gaseous fuels, an increased overall hydrogen-carbon ratio lowers CO₂ emissions compared with normal engine operation. Power output (in terms of brake mean effective pressure, BMEP) as well as maximum engine speed achieved are also limited. This results from a reduced gaseous fuel induction capability in the intake manifold, in addition to engine stability issues (i.e. abnormal combustion). During all engine operating modes, diesel pilot fuel and RME pilot fuel performed closely in terms of exhaust emissions. Overall, CI engines can operate in the dual-fuel mode reasonably successfully with minimal modifications. However, increased NO_x emissions (with hydrogen use) and incomplete combustion at low and intermediate loads (with natural gas use) are concerns; while port gaseous fuel induction limits power output at high speeds.     

Combustion and emissions characteristics of compression-ignition engine using dual ammonia-diesel fuel

This study investigated the combustion and emissions characteristics of a compression-ignition engine using a dual-fuel approach with ammonia and diesel fuel. Ammonia can be regarded as a hydrogen carrier and used as a fuel, and its combustion does not produce carbon dioxide. In this study, ammonia vapor was introduced into the intake manifold and diesel fuel was injected into the cylinder to initiate combustion. The test engine was a four-cylinder, turbocharged diesel engine with slight modifications to the intake manifold for ammonia induction. An ammonia fueling system was developed, and various combinations of ammonia and diesel fuel were successfully tested. One scheme was to use different combinations of ammonia and diesel fuel to achieve a constant engine power. The other was to use a small quantity of diesel fuel and vary the amount of ammonia to achieve variable engine power. Under the constant engine power operation, in order to achieve favorable fuel efficiency, the preferred operation range was to use 40-60% energy provided by diesel fuel in conjunction with 60-40% energy supplied by ammonia. Exhaust carbon monoxide and hydrocarbon emissions using the dual-fuel approach were generally higher than those of using pure diesel fuel to achieve the same power output, while NO_x emissions varied with different fueling combinations. NO_x emissions could be reduced if ammonia accounted for less than 40% of the total fuel energy due to the lower combustion temperature resulting in lower thermal NO_x. If ammonia accounted for the majority of the fuel energy, NO_x emissions increased significantly due to the fuel-bound nitrogen. On the other hand, soot emissions could be reduced significantly if a significant amount of ammonia was used due to the lack of carbon present in the combination of fuels. Despite the overall high ammonia conversion efficiency (nearly 100%), exhaust ammonia emissions ranged from 1000 to 3000 ppmV and further after-treatment will be required due to health concerns. On the other hand, the variable engine power operation resulted in relatively poor fuel efficiency and high exhaust ammonia emissions due to the lack of diesel energy to initiate effective combustion of the lean ammonia-air mixture. The in-cylinder pressure history was also analyzed, and results indicated that ignition delay increased with increasing amounts of ammonia due to its high resistance to autoignition. The peak cylinder pressure also decreased because of the lower combustion temperature of ammonia. It is recommended that further combustion optimization using direct ammonia/diesel injection strategies be performed to increase the combustion efficiency and reduce exhaust ammonia emissions.     

Emissions from different alternative diesel fuels operating with single and split fuel injection

Few factors affect diesel combustion and emissions more significantly than the composition of the fuel and the fuel injection process. In this paper, both of these factors are considered by comparing conventional, synthetic and vegetable oil-derived diesel fuels and by comparing a single pulse injection and a split (pilot and main) injection process. This paper focuses on characterization of the combustion process and emissions produced by three substantially different diesel fuels: an ultra low sulfur diesel fuel (BP15), a pure soybean methyl ester (B100), and a synthetic, practically free of sulfur and aromatic compounds, Fischer-Tropsch fuel (FT) produced in a gas-to-liquid process. The study was carried out in a direct injection (DI) 2.5 L common-rail turbodiesel engine working at four engine operation modes, spanning conditions of most interest in the engine map. In all modes the engine was tested with single and split injection (pilot and main), with constant start of injection (SOI), and without exhaust gas recirculation (EGR). Using the results from thermodynamic analysis, this study confirms that the ignition character of the fuel affects the start of the combustion process, notably for the whole combustion process when the single injection is used, and during the combustion process after the pilot injection when the split injection is used. In general, the FT fuel can reduce both NOx and PM specific emissions in all modes under both single and split injection modes, bypassing the nitrogen oxides-particulate matter (NOx-PM) trade-off. Finally, this work confirms that biodiesel can reduce the particle concentration. However, in some cases an increase of PM mass emission has been observed and this increase of the PM mass emission is due to unburned or partially burned hydrocarbon (HC) emissions.     

绿色过氧化氢双组元自燃推进剂

过氧化氢/煤油或过氧化氢/醇类(如乙醇、异丙醇和正丁醇等)组合,由于环境友好和可贮存性而成为最具竞争力的双组元推进剂,但这种推进剂组合本身并不能自燃点火。通过向煤油或醇类燃料中加入可溶性添加剂的均相催化法解决了该推进剂组合的自燃点火关键技术,用滴流点火试验和自燃点火延迟期测定仪确定了一些推进剂组合的自燃点火性能,并通过发动机热试车对某些推进剂组合的自燃性能和稳态燃烧特性进行了评估。     

Experimental study on performance and emissions of a high speed diesel engine fuelled with n-butanol diesel blends under premixed low temperature combustion

In the present paper, results of an experimental investigation carried out in a modern diesel engine running at different operative conditions and fuelled with blends of diesel and n-butanol, are reported. The exploration strategy was focused on the management of the timing and injection pressure to achieve a condition in which the whole amount of fuel was delivered before ignition. The aim of the paper was to evaluate the potential to employ fuel blends having low cetane number and high resistance to auto-ignition to reduce engine out emissions of NOx and smoke without significant penalty on engine performance. Fuel blends were mixed by the baseline diesel (BU00) with 20% and 40% of n-butanol by volume. The n-butanol was taken by commercial production that is largely produced through petrochemical pathways although the molecule is substantially unchanged for butanol produced through biological mechanisms.The experimental activity was performed on a turbocharged, water cooled, DI diesel engine, equipped with a common rail injection system. The engine equipment includes an exhaust gas recirculation system controlled by an external driver, a piezo-quartz pressure transducer to detect the in-cylinder pressure signal and a current probe to acquire the energizing current to the injectors. Engine tests were carried out at 2500 rpm and 0.8 MPa of BMEP exploring the effect of start of injection, O₂ concentration at intake and injection pressure on combustion behavior and engine out emissions. The in-cylinder pressure and rate of heat release were investigated for the neat diesel and the two blends to evaluate engine performance and exhaust emissions both for the conventional diesel and the advanced premixed combustion processes.The management of injection pressure, O₂ concentration at intake and injection timing allowed to realize a partial premixed combustion by extending the ignition delay, particularly for blends. The main results of the investigation made reach smoke and NOx emissions due to the longer ignition delay and a better mixing control before combustion. The joint effect of higher resistance to auto ignition and higher volatility of n-butanol blends improved emissions compared to the neat diesel fuel with a low penalty on fuel consumption.     

Effect of injection and ignition timings on performance and emissions from a spark-ignition engine fueled with methanol

Optimal injection and ignition timings and the effects of injection and ignition timings on performance and emissions from a high-compression direct-injection stratified charge spark-ignition methanol engine have been investigated experimentally. The results have shown that direct-injection spark-ignition methanol engine, in which a non-uniform mixture with a stratified distribution can be formed, has optimal injection and ignition timings to obtain a good combustion and low exhaust emissions in the overall mode range. Both methanol injection timing and ignition timing have a significant effect on methanol engine performance, combustion, and exhaust emissions. At an engine speed of 1600 rpm, full load, and optimal injection and ignition timings, methanol engine can obtain shorter ignition delay, lesser cycle-by-cycle variation, the maximum in-cylinder pressure, the maximum heat release rate, and higher thermal efficiency compared to the case of non-optimized injection and ignition timings. For methanol engine, the optimization of injection timing and ignition timing can lead to an improvement of brake-specific fuel consumption of more than 10% compared to non-optimized case in the overall load range and engine speed of 1600 rpm. The best compromise between thermal efficiency and exhaust emissions is reached at optimal injection and ignition timings.     

Effect of a narrow fuel spray angle and a dual injection configuration on the improvement of exhaust emissions in a HCCI diesel engine

The aim of this work was to investigate the effect of narrow fuel spray angle injection and dual injection strategy on the exhaust emissions of a common-rail diesel engine. To achieve successful homogeneous charge compression ignition by an early timing injection, a narrowed spray cone angle injector and a reduced compression ratio were employed. The combination of homogeneous charge compression ignition (HCCI) combustion and conventional diesel combustion was studied to examine the exhaust emission and combustion characteristics of the engine under various fuel injection parameters, such as injection timings of the first and second spray.The results showed that a dual injection strategy consisting of an early timing for the first injection for HCCI combustion and a late timing for the second injection was effective to reduce the NO_x emissions while it suppress the deterioration of the combustion efficiency caused by the HCCI combustion.     

Selection of a diesel fuel surrogate for the prediction of auto-ignition under HCCI engine conditions

Homogeneous charged compression ignition (HCCI) is a promising combustion concept able to provide very low NO_x and PM diesel engine emissions while keeping good fuel economy. Since HCCI combustion is a kinetically controlled process, the availability of a kinetic reaction mechanism to simulate the oxidation (low and high temperature regimes) of a diesel fuel is necessary for the optimisation, control and design of HCCI engines. Motivated by the lack of information regarding reliable diesel fuel ignition values under real HCCI diesel engine conditions, a diesel fuel surrogate has been proposed in this work by merging n-heptane and toluene kinetic mechanisms. The surrogate composition has been selected by comparing modelled ignition delay angles with experimental ones obtained from a single cylinder DI diesel engine tests. Modelled ignition angle results are in agreement with the experimental ones, both results following the same trends when changing the engine operating conditions (engine load and speed, start of injection and EGR rate). The effect of EGR, which is one of the most promising techniques to control HCCI combustion, depends on the engine load. High EGR rates decrease the n-heptane/toluene mixture reactivity when increasing the engine load but the opposite effect has been observed for lower EGR rates. A chemical kinetic analysis has shown that the influence of toluene on the ignition time is significant only at low initial temperature. More delayed combustion processes have been found when toluene is added, the dehydrogenation of toluene by OH (termination reaction) being the main kinetic path involved during toluene oxidation.     

Fuelling of a compression ignition engine on ethanol with DME as ignition promoter: Effect of injector configuration

The effect of injector configuration on the combustion and emissions of a compression ignition engine, fuelled on ethanol as the main fuel and dimethyl ether as ignition promoter, were investigated. Baseline constant speed tests were initially performed on diesel fuel using the recommended three-hole configuration. The tests were repeated with the recommended three-hole injector and then with a four-hole injector with ethanol as the main fuel. All other aspects of the engine remained unmodified. The four-hole injector resulted in the combustion of ethanol occurring closer to top dead centre, producing marginally more power and higher fuel conversion efficiency. In the case of the four-hole injector, emissions of both THC and NO_X were found to be lower than those produced by the three-hole injector. They were, however, in both cases lower than levels achieved with diesel fuelling.     

Shock tube investigation of propane-air mixtures with a pilot diesel fuel or cotton methyl ester

The propane (or LPG) is one of the best candidates as an alternative fuel in dual-fuel engines which operate primarily on any type of gaseous fuel using pilot injection of diesel to achieve ignition. The ignition delay has received considerable attention in the published literature for various gaseous fuels using different dual-fuel engines which showed that the ignition delay in a dual-fuel engine is different from that in a diesel engine especially at low loads. In this research, the measurement of ignition delay of propane-air mixtures with a pilot diesel fuel or cotton methyl ester (CME) similar to mixtures used in dual-fuel engines have been performed in a shock tube. The operating conditions were the equivalence ratio ranging from 0.3 to 1.2, the initial pressure varied from 0.4 to 1.0 bar, the initial temperature varied from 423 to 673 K, the relative mass of pilot liquid fuel and the type of liquid fuel. The ignition-delay times were measured using a piezo-electric pressure transducer, charge amplifier, data acquisition card, PC computer and LabVIEW program. From the results, it is shown that, the minimum ignition-delay time for the dual-fuel combustion was observed at stoichiometric equivalence ratio for propane-air mixtures with a pilot diesel fuel or CME. Higher initial temperatures and pressures reduced the ignition delay. Also, the ignition delays of propane-air mixtures are affected by changes in pilot fuel quantities and properties.     

Influence of ethanol blends on the combustion performance and exhaust emission characteristics of a four-cylinder diesel engine at various engine loads and injection timings

The aim of this work is to investigate the effect of ethanol blending to diesel fuel on the combustion and exhaust emission characteristics of a four-cylinder diesel engine with a common-rail injection system. The overall spray characteristics, such as the spray tip penetration and the spray cone angle, were studied with respect to the ethanol blending ratio. A spray visualization system and a four-cylinder diesel engine equipped with a combustion and emission analyzer were utilized so as to analyze the spray and exhaust emission characteristics of the ethanol blending diesel fuel. Ethanol blended diesel fuel has a shorter spray tip penetration when compared to pure diesel fuel. In addition, the spray cone angle of ethanol blended fuels is larger. It is believed that the lower fuel density of ethanol blended fuels affects the spray characteristics. When the ethanol blended fuels are injected around top dead center (TDC), they exhibit unstable ignition characteristics because the higher ethanol blending ratio causes a long ignition delay. An advance in the injection timing also induces an increase in the combustion pressure due to the sufficient premixed duration. In a four-cylinder diesel engine, an increase in the ethanol blending ratio leads to a decrease in NO_x emissions due to the high heat of evaporation of ethanol fuel, however, CO and HC emissions increase. In addition, the CO and HC emissions exhibit a decreasing trend according to an increase in the engine load and an advance in the injection timing.     

Experimental investigation on dual fuel operation of acetylene in a DI diesel engine

Depletion of fossils fuels and environmental degradation have prompted researchers throughout the world to search for a suitable alternative fuel for diesel engine. One such step is to utilize renewable fuels in diesel engines by partial or total replacement of diesel in dual fuel mode. In this study, acetylene gas has been considered as an alternative fuel for compression ignition engine, which has excellent combustion properties.Investigation has been carried out on a single cylinder, air cooled, direct injection (DI), compression ignition engine designed to develop the rated power output of 4.4 kW at 1500 rpm under variable load conditions, run on dual fuel mode with diesel as injected primary fuel and acetylene inducted as secondary gaseous fuel at various flow rates. Acetylene aspiration resulted in lower thermal efficiency. Smoke, HC and CO emissions reduced, when compared with baseline diesel operation. With acetylene induction, due to high combustion rates, NO_x emission significantly increased. Peak pressure and maximum rate of pressure rise also increased in the dual fuel mode of operation due to higher flame speed. It is concluded that induction of acetylene can significantly reduce smoke, CO and HC emissions with a small penalty on efficiency.     

Methyl and ethyl soybean esters as renewable fuels for diesel engines

The primary problems associated with using straight soybean oil as a fuel in a compression ignition internal combustion engine are caused by high fuel viscosity. Transesterification of soybean oil with an alcohol provides a significant reduction in viscosity, thereby enhancing the physical properties of the renewable fuel to improve engine performance. The ethyl and methyl esters of soybean oil with commercial diesel fuel additives revealed fuel properties that compared very well with diesel fuel, with the exception of gum formation, which manifested itself in problems with the plugging of fuel filters. Engine performance using soybean ester fuels differed little from engine performance with diesel fuel. A slight power loss combined with an increase in fuel consumption were experienced with the esters, primarily because of the lower heating value of the esters than for diesel fuel. Emissions for the 2 fuels were similar, with nitrous oxide emissions higher for the esters. Measurements of engine wear and fuel-injection system tests showed no abnormal characteristics for any of the fuels after the 200-hr tests. Engine deposits were comparable in amount, but slightly different in color and texture, with the methyl ester engine experiencing greater carbon and varnish deposits on the pistons. Presented at the American Oil Chemists’ Society meeting, Chicago, May 1983.     

Study on the controlling strategies of homogeneous charge compression ignition combustion with fuel of dimethyl ether and methanol

The controlling strategies of homogeneous charge compression ignition (HCCI) fueled by dimethyl ether (DME) and methanol were investigated. The experimental work was carried out on a modified single-cylinder diesel engine, which was fitted with port injection of DME and methanol dual fuel. The results show that exhaust gas recirculation (EGR) rate and DME percentage are two important parameters to control the HCCI combustion process. The ignition timing and combustion duration can be regulated in a suitable range with high indicated thermal efficiency and low emissions by adjusting the DME percentage and EGR rate. EGR cannot extend the maximum indicate mean effective pressure (IMEP) of HCCI operation range with dual fuel, but can enlarge the DME percentage range in normal combustion. The combustion efficiency largely depends on DME percentage, and EGR can improve combustion efficiency. The results also show that HC emissions strongly depend upon DME percentage, and CO emissions have good coherence to the peak mean temperature in cylinder. In normal combustion, adopting large DME percentage and high EGR rate can attain an optimal HCCI combustion.     

Influence of fuel and air/fuel equivalence ratio on the emission of hydrocarbons from a SI engine. 1. Experimental findings

A spark ignition engine was used to study the impact of fuel composition and of the air/fuel equivalence ratio on exhaust emissions of specific hydrocarbons. The fuel blends used contained eight main hydrocarbons and four oxygenated compounds. The fuel components that produce each exhaust pollutant are identified. The emissions of all HC generally decrease with the addition of oxygenated compounds, except sometimes in the case of methane, ethane and cyclohexane. Under rich conditions, the relative increase of exhaust methane and benzene is more important than the other saturated HC. Some HC are correlated with the physical properties of the fuel and other exhaust pollutants.     

Effect of an H2O2 additive on hydrogen ignition and combustion in a supersonic air flow

The effect of small amounts of inert and reacting additives (such as hydrogen peroxide, its decomposition products,CO ₂, etc.) on the ignition and combustion of hydrogen in a high-temperature supersonic air flow was studied experimentally. It is shown that direct doping of the fuel has little effect on the combustion ofH ₂, whereas injection of hydrogen peroxide or small amounts of pure hydrogen ahead of the nozzle decreases suddenly the ignition delay, indicating the profound effect of the reaction products. Comparative experiments with inert additives showed that these additives only lead to a decrease in the air-flow temperature. Institute of Theoretical and Applied Mechanics, Siberian Division, Russian Academy of Sciences, Novosibirsk 630090. Translated from Fizika Goreniya i Vzryva, Vol. 33, No. 3, pp. 70–75, May–June, 1997.