Performance and emission characteristics of an CI engine fueled with diesel–biodiesel–bioethanol blends

The paper presents the experimental results obtained concerning performances and pollution of a diesel engine fueled with diesel–biodiesel–ethanol blends compared with diesel fuel in laboratory tests. The main properties of the researched fuels are presented within this paper, in comparison with classical diesel fuel (chemical composition, density, kinematic viscosity, cold filter plugging point, flash point). Engines’ performances were evaluated by determining the brake specific fuel consumption and brake thermal efficiency. For pollution evaluation the emissions of CO, CO₂, NO_x, HC and smoke have been measured. An increasing of brake specific fuel consumption has been observed, especially at lower engines’ loads, with maximum 32.4%, reducing engine brake thermal efficiency with maximum 21.7%. CO emissions decrease, especially at high loads with maximum 59%, on the basis of CO₂ increased emissions. NO_x emissions slightly increase, especially at partial and high loads, meanwhile HC and smoke emissions decrease in all engines’ load cycles.     

Aviation fuel JP-5 and biodiesel on a diesel engine

Naval aviation turbine fuel, JP-5, has been accepted as alternative to JP-8 in the frame of the Single Fuel Policy. This has resulted in some ongoing research on JP-5 fuel for its application as a naval single fuel. The necessity to cope with the environmental problems identified in the process of implementing the Single Fuel Policy as well as the strict requirements of modern diesel engines has lead to the need of improved single fuel quality. The development of biomass derived substitutes for diesel, such as biodiesel, is a possible attractive solution. The present paper is an effort to evaluate JP-5 along with diesel and biodiesel for use in a diesel engine. These fuels were used alone and in various mixture fractions in a single cylinder stationary diesel engine in order to evaluate their performance under defined operating conditions of the engine. JP-5 reduced both the NOx and particulate matter emissions as compared to the reference fuel case. Biodiesel significantly lowered particulate emissions, but slightly increased NOx emissions and fuel consumption. Fuel sulfur content has an undesired effect on smoke opacity. Biodiesel increased the fuel consumption when added to petroleum fuels and the increase was larger at high engine loads. Diesel and JP-5 showed similar fuel consumption, with diesel consumption increasing at high engine loads. Ternary blends showed similar behavior. The blends with lower biodiesel content showed lower volumetric fuel consumption.     

Experimental investigation on the combustion and exhaust emission characteristics of biogas-biodiesel dual-fuel combustion in a CI engine

An experimental investigation was performed to study the influence of dual-fuel combustion characteristics on the exhaust emissions and combustion performance in a diesel engine fueled with biogas-biodiesel dual-fuel. In this work, the combustion pressure and the rate of heat release were evaluated under various conditions in order to analyze the combustion and emission characteristics for single-fuel (diesel and biodiesel) and dual-fuel (biogas-diesel and biogas-biodiesel) combustion modes in a diesel engine. In addition, to compare the engine performances and exhaust emission characteristics with combustion mode, fuel consumption, exhaust gas temperature, efficiency, and exhaust emissions were also investigated under various test conditions. For the dual-fuel system, the intake system of the test engine was modified to convert into biogas and biodiesel of a dual-fueled combustion engine. Biogas was injected during the intake process by two electronically controlled gas injectors, which were installed in the intake pipe.The results of this study showed that the combustion characteristics of single-fuel combustion for biodiesel and diesel indicated the similar patterns at various engine loads. In dual-fuel mode, the peak pressure and heat release for biogas-biodiesel were slightly lower compared to biogas-diesel at low load. At 60% load, biogas-biodiesel combustion exhibited the slightly higher peak pressure, rate of heat release (ROHR) and indicated mean effective pressure (IMEP) than those of diesel. Also, the ignition delay for biogas-biodiesel indicated shortened trends compared to ULSD dual-fueling due to the higher cetane number (CN) of biodiesel. Significantly lower NO_x emissions were emitted under dual-fuel operation for both cases of pilot fuels compared to single-fuel mode at all engine load conditions. Also, biogas-biodiesel provided superior performance in reductions of soot emissions due to the absence of aromatics, the low sulfur, and oxygen contents for biodiesel.     

Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine

Non-edible filtered high viscous (72 cSt at 40 °C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO₂, HC, NO_x, and O₂) were recorded. The optimum engine operating condition based on lower brake specific fuel consumption and higher brake thermal efficiency was observed at 100% load for neat biodiesel. From emission point of view the neat POME was found to be the best fuel as it showed lesser exhaust emission as compared to HSD.     

Comparison of emissions of a direct injection diesel engine operating on biodiesel with emulsified and fumigated methanol

Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NO_x) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO₂, NO_x, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal efficiency at low engine load while the fumigation mode gives slightly higher brake thermal efficiency at medium and high engine loads. In the fumigation mode, an extra fuel injection control system is required, and there is also an increase in CO, HC and NO₂ (nitrogen dioxide) and particulate emissions in the engine exhaust, which are disadvantages compared with the blended mode.     

Performance of compression ignition engine with mahua (Madhuca indica) biodiesel

The performance of biodiesel obtained from mahua oil and its blend with high speed diesel in a Ricardo E6 engine has been presented in this paper together with some of its fuel properties. These properties were found to be comparable to diesel and confirming to both the American and European standards. Engine performance (brake specific fuel consumption, brake thermal efficiency and exhaust gas temperature) and emissions (CO, smoke density and NO_x) were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The reductions in exhaust emissions and brake specific fuel consumption together with increase brake power, brake thermal efficiency made the blend of biodiesel (B20) a suitable alternative fuel for diesel and thus could help in controlling air pollution.     

Study of oxygenated biomass fuel blends on a diesel engine

Vegetable methyl ester was added in ethanol–diesel fuel to prevent separation of ethanol from diesel in this study. The ethanol blend proportion can be increased to 30% in volume by adding the vegetable methyl ester. Engine performance and emissions characteristics of the fuel blends were investigated on a diesel engine and compared with those of diesel fuel. Experimental results show that the torque of the engine is decreased by 6%–7% for every 10% (by volume) ethanol added to the diesel fuel without modification on the engine. Brake specific fuel consumption (BSFC) increases with the addition of oxygen from ethanol but equivalent brake specific fuel consumption (EBSFC) of oxygenated fuels is at the same level of that of diesel. Smoke and particulate matter (PM) emissions decrease significantly with the increase of oxygen content in the fuel. However, PM reduction is less significant than smoke reduction. In addition, PM components are affected by the oxygenated fuel. When blended fuels are used, nitrogen oxides (NO_x) emissions are almost the same as or slightly higher than the NO_x emissions when diesel fuel is used. Hydrocarbon (HC) is apparently decreased when the engine was fueled with ethanol–ester–diesel blends. Fuelling the engine with oxygenated diesel fuels showed increased carbon monoxide (CO) emissions at low and medium loads, but reduced CO emissions at high and full loads, when compared to pure diesel fuel.     

Effect of EGR and injection timing on combustion and emission characteristics of split injection strategy DI-diesel engine fueled with biodiesel

In this study, the effect of injection timing and EGR rate on the combustion and emissions of a Ford Lion V6 split injection strategy direct injection diesel engine has been experimentally investigated by using neat biodiesel produced from soybean oil. The results showed that, with the increasing of EGR rate, the brake specific fuel combustion (BSFC) and soot emission were slightly increased, and nitrogen oxide (NO_x) emission was evidently decreased. Under higher EGR rate, the peak pressure was slightly lower, and the peak heat release rate kept almost identical at lower engine load, and was higher at higher engine load. With the main injection timing retarded, BSFC was slightly increased, NO_x emission was evidently decreased, and soot emission hardly varied. The second peak pressure was evidently decreased and the heat release rate was slightly increased.     

Comparative performance and emissions of IDI-turbo automobile diesel engine operated using degummed, deacidified mixed crude palm oil-diesel blends

The performance and emissions of an indirect injection (IDI)-turbo automobile diesel engine operated with diesel and blends of degummed-deacidified mixed crude palm oil in diesel at portions of 20, 30, and 40 vol.% are examined and compared at various loads and speeds. Although fuel properties of the tested blends do not exactly meet all regulations of Thailand, they are all able to operate the engine. Comparing this with diesel, especially at full loads, shows that all blends produce the same maximum brake torque and power. A higher blending portion results in a little higher brake specific fuel consumption (+4.3% to +7.6%), a slightly lower brake thermal efficiency (-3.0% to -5.2%), a slightly lower exhaust gas temperature (−2.7% to −3.4%), and a significantly lower amount of black smoke (−30% to −45%). The level of carbon monoxide from the 20 vol.% blend is significantly lower (−70%), and the levels of nitrogen oxides from all blends are little higher.     

Comparative study of performance and emissions of a diesel engine using Chinese pistache and jatropha biodiesel

An experimental study of the performances and emissions of a diesel engine is carried out using two different biodiesels derived from Chinese pistache oil and jatropha oil compared with pure diesel. The results show that the diesel engine works well and the power outputs are stable running with the two selected biodiesels at different loads and speeds. The brake thermal efficiencies of the engine run by the biodiesels are comparable to that run by pure diesel, with some increases of fuel consumptions. It is found that the emissions are reduced to some extent when using the biodiesels. Carbon monoxide (CO) emissions are reduced when the engine run at engine high loads, so are the hydrocarbon (HC) emissions. Nitrogen oxides (NOx) emissions are also reduced at different engine loads. Smoke emissions from the engine fuelled by the biodiesels are lowered significantly than that fuelled by diesel. It is also found that the engine performance and emissions run by Chinese pistache are very similar to that run by jatropha biodiesel.     

Combustion analysis of Jatropha, Karanja and Polanga based biodiesel as fuel in a diesel engine

Non-edible filtered Jatropha (Jatropha curcas), Karanja (Pongamia pinnata) and Polanga (Calophyllum inophyllum) oil based mono esters (biodiesel) produced and blended with diesel were tested for their use as substitute fuels of diesel engines. The major objective of the present investigations was to experimentally access the practical applications of biodiesel in a single cylinder diesel engine used in generating sets and the agricultural applications in India. Diesel; neat biodiesel from Jatropha, Karanja and Polanga; and their blends (20 and 50 by v%) were used for conducting combustion tests at varying loads (0, 50 and 100%). The engine combustion parameters such as peak pressure, time of occurrence of peak pressure, heat release rate and ignition delay were computed. Combustion analysis revealed that neat Polanga biodiesel that results in maximum peak cylinder pressure was the optimum fuel blend as far as the peak cylinder pressure was concerned. The ignition delays were consistently shorter for neat Jatropha biodiesel, varying between 5.9^° and 4.2^° crank angles lower than diesel with the difference increasing with the load. Similarly, ignition delays were shorter for neat Karanja and Polanga biodiesel when compared with diesel.     

Combustion, performance and emission characteristics of a DI diesel engine fueled with ethanol-biodiesel blends

In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NO_x and particulate emissions of the diesel engine. The effectiveness of NO_x and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.     

Experimental investigation of fuel properties, engine performance, combustion and emissions of blends containing croton oil, butanol, and diesel on a CI engine

Emission problems associated with the use of fossil fuels have led to numerous research projects on the use of renewable fuels. The aim of this study is to evaluate the effects of blends containing croton mogalocarpus oil (CRO)-Butanol (BU) alcohol-diesel (D2) on engine performance, combustion, and emission characteristics. Samples investigated were 15%CRO-5%BU-80%D2, 10%CRO-10%BU-80%D2, and diesel fuel (D2) as a baseline. The density, viscosity, cetane number CN, and contents of carbon, hydrogen, and oxygen were measured according to ASTM standards. A four cylinder turbocharged direct injection (TDI) diesel engine was used for the tests. It was observed that brake specific energy consumption (BSEC) of blends was found to be high when compared with that of D2 fuel. Butanol containing blends show peak cylinder pressure and heat release rate comparable to that of D2 on higher engine loads. Carbon dioxide (CO₂) and smoke emissions of the BU blends were lower in comparison to D2 fuel.     

The influence of n-butanol/diesel fuel blends utilization on a small diesel engine performance and emissions

Nitrogen oxides and smoke emissions are the most significant emissions for the diesel engines. Especially, fuels containing high-level oxygen content can have potential to reduce smoke emissions significantly. The aim of the present study is to evaluate the influence of n-butanol/diesel fuel blends (as an oxygenation additive for the diesel fuel) on engine performance and exhaust emissions in a small diesel engine. For this aim five-test fuels, B5 (contains 5% n-butanol and 95% diesel fuel in volume basis), B10, B15, B20 and neat diesel fuel, were prepared to test in a diesel engine. Tests were performed in a single cylinder, four stroke, unmodified, and naturally aspirated DI high speed diesel engine at constant engine speed (2600 rpm) and four different engine loads by using five-test fuels. The experimental test results showed that smoke opacity, nitrogen oxides, and carbon monoxide emissions reduced while hydrocarbon emissions increased with the increasing n-butanol content in the fuel blends. In addition, there is an increase in the brake specific fuel consumption and in the brake thermal efficiency with increasing n-butanol content in fuel blends. Also, exhaust gas temperature decreased with increasing n-butanol content in the fuel blends.     

Experimental investigation of diesel engine performance and emission characteristics using jojoba/diesel blend and sunflower oil

Experimental study has been carried out to investigate performance parameters, emissions, cylinder pressure, exhaust gas temperature (T_exhaust) and engine wall temperatures (T_wall) for direct injection diesel engine. Tests were conducted for sunflower oil (S100) and 20% jojoba oil + 80% pure diesel fuel (B20) in comparison to pure diesel fuel with different engine speeds. S100 and B20 were selected for the study because of its being widely used in Egypt and in the world. Also, series of tests are conducted at same previous conditions with different percentage of exhaust gas recirculation (EGR) from 0% to 12% of inlet mass of air fresh charge. Results indicate that S100 or B20 gives lower brake thermal efficiency (η_B), brake power (BP), brake mean effective pressure (BMEP), and higher brake specific fuel consumption (BSFC) due to lower heating value compared to pure diesel fuel. S100 or B20 gives lower NO_X concentration due to lower gas temperature. S100 or B20 gives higher T_wall and T_exhaust due to incomplete combustion inside engine cylinder. S100 or B20 gives higher CO and CO₂ concentrations due to higher carbon/hydrogen ratio. The position of maximum pressure (P_max) change for pure diesel fuel is earlier than for S100 or B20. The results show that S100 or B20 are promising as alternative fuel for diesel engine. The utilization of vegetable oils does not require a significant modification of existing engines. This can be seen as the main advantage of vegetable oils. The main disadvantages of biodiesel fuels are high viscosity, drying with time, thickening in cold conditions, flow and atomization characteristics.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Fuel consumption and emissions from a diesel power generator fuelled with castor oil and soybean biodiesel

This work investigates the impacts on fuel consumption and exhaust emissions of a diesel power generator operating with biodiesel. Fuel blends with 5%, 20%, 35%, 50%, and 85% of soybean biodiesel in diesel oil, and fuel blends containing 5%, 20%, and 35% of castor oil biodiesel in diesel oil were tested, varying engine load from 9.6 to 35.7 kW. Specific fuel consumption (SFC) and the exhaust concentrations of carbon dioxide (CO₂), carbon monoxide (CO), and hydrocarbons (HC) were evaluated. The engine was kept with its original settings for diesel oil operation. The results showed increased fuel consumption with higher biodiesel concentration in the fuel. Soybean biodiesel blends showed lower fuel consumption than castor biodiesel blends at a given concentration. At low and moderate loads, CO emission was increased by nearly 40% and over 80% when fuel blends containing 35% of castor oil biodiesel or soybean biodiesel were used, respectively, in comparison with diesel oil. With the load power of 9.6 kW, the use of fuel blends containing 20% of castor oil biodiesel or soybean biodiesel increased HC emissions by 16% and 18%, respectively, in comparison with diesel oil. Exhaust CO₂ concentration did not change significantly, showing differences lower than ±3% of the values recorded for diesel oil operation, irrespective of biodiesel type, concentration and the load applied. The results demonstrate that optimization of fuel injection system is required for proper engine operation with biodiesel.     

Influence of Methanol–Biodiesel Blends on the Particulate Emissions of a Direct Injection Diesel Engine

In this study, Euro V diesel fuel, biodiesel, and methanol–biodiesel blends were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion characteristics and particulate emissions of the diesel engine under five engine loads at the maximum torque engine speed of 1800 rpm. Compared with Euro V diesel fuel, biodiesel gives lower and earlier heat release rate. For the blended fuels, the peak heat release rate becomes higher and retarded. With regard to particulate mass concentration, biodiesel generates less than Euro V diesel fuel, while the blended fuels result in significant reduction especially at high engine loads. Compare with Euro V diesel fuel, the total particle number concentration of using biodiesel is always higher while the geometric mean diameter (GMD) of the particles is lower. With the blended fuel, the total number concentration and GMD decrease in comparison with pure biodiesel. Further analysis shows that the difference between the total number concentration of biodiesel and Euro V diesel fuel is in particles smaller than 50 nm rather than in the larger particles. The use of methanol–biodiesel blends, compared with biodiesel, could reduce the number concentration of all sizes. A comparison between the particulate mass emission and total particulate number concentration with the mass of fuel burned in the diffusion mode show that they are strongly related to each other, even for the blended fuel.     

Determination of performance and exhaust emissions properties of B75 in a CI engine application

In this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO₂, and O₂ emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2-3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO₂, CO, HC, smoke opacity and NO_x emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.