Diesel and rapeseed methyl ester (RME) pilot fuels for hydrogen and natural gas dual-fuel combustion in compression-ignition engines

This paper presents experimental results of rapeseed methyl ester (RME) and diesel fuel used separately as pilot fuels for dual-fuel compression-ignition (CI) engine operation with hydrogen gas and natural gas (the two gaseous fuels are tested separately). During hydrogen dual-fuel operation with both pilot fuels, thermal efficiencies are generally maintained. Hydrogen dual-fuel CI engine operation with both pilot fuels increases NO_x emissions, while smoke, unburnt HC and CO levels remain relatively unchanged compared with normal CI engine operation. During hydrogen dual-fuel operation with both pilot fuels, high flame propagation speeds in addition to slightly increased ignition delay result in higher pressure-rise rates, increased emissions of NO_x and peak pressure values compared with normal CI engine operation. During natural gas dual-fuel operation with both pilot fuels, comparatively higher unburnt HC and CO emissions are recorded compared with normal CI engine operation at low and intermediate engine loads which are due to lower combustion efficiencies and correspond to lower thermal efficiencies. This could be due to the pilot fuel failing to ignite the natural gas-air charge on a significant scale. During dual-fuel operation with both gaseous fuels, an increased overall hydrogen-carbon ratio lowers CO₂ emissions compared with normal engine operation. Power output (in terms of brake mean effective pressure, BMEP) as well as maximum engine speed achieved are also limited. This results from a reduced gaseous fuel induction capability in the intake manifold, in addition to engine stability issues (i.e. abnormal combustion). During all engine operating modes, diesel pilot fuel and RME pilot fuel performed closely in terms of exhaust emissions. Overall, CI engines can operate in the dual-fuel mode reasonably successfully with minimal modifications. However, increased NO_x emissions (with hydrogen use) and incomplete combustion at low and intermediate loads (with natural gas use) are concerns; while port gaseous fuel induction limits power output at high speeds.     

Study of oxygenated biomass fuel blends on a diesel engine

Vegetable methyl ester was added in ethanol–diesel fuel to prevent separation of ethanol from diesel in this study. The ethanol blend proportion can be increased to 30% in volume by adding the vegetable methyl ester. Engine performance and emissions characteristics of the fuel blends were investigated on a diesel engine and compared with those of diesel fuel. Experimental results show that the torque of the engine is decreased by 6%–7% for every 10% (by volume) ethanol added to the diesel fuel without modification on the engine. Brake specific fuel consumption (BSFC) increases with the addition of oxygen from ethanol but equivalent brake specific fuel consumption (EBSFC) of oxygenated fuels is at the same level of that of diesel. Smoke and particulate matter (PM) emissions decrease significantly with the increase of oxygen content in the fuel. However, PM reduction is less significant than smoke reduction. In addition, PM components are affected by the oxygenated fuel. When blended fuels are used, nitrogen oxides (NO_x) emissions are almost the same as or slightly higher than the NO_x emissions when diesel fuel is used. Hydrocarbon (HC) is apparently decreased when the engine was fueled with ethanol–ester–diesel blends. Fuelling the engine with oxygenated diesel fuels showed increased carbon monoxide (CO) emissions at low and medium loads, but reduced CO emissions at high and full loads, when compared to pure diesel fuel.     

An experimental investigation of CNG as an alternative fuel for a retrofitted gasoline vehicle

This paper presents test results obtained from running a 1.5 L, 4-cylinder Proton Magma retrofitted spark ignition car engine with dynamometer. Performance, fuel consumption and exhaust emissions measurements were recorded under steady state operating conditions for gasoline and compressed natural gas (CNG). The engine was converted to computer integrated bi-fueling system from a gasoline engine and was operated separately either with gasoline or CNG using an electronically controlled solenoid actuated valve system. A PC based data acquisition and control system was used for controlling all the operation. A comparative analysis of the performance and emissions has been made for gasoline and CNG. Based on the experimental results, it is transparent that CNG shows low brake mean effective pressure (BMEP), brake specific fuel consumptions (BSFC), higher efficiency and lower emissions of CO, CO₂, HC but more NO_x compared to gasoline.     

Exhaust emissions from a diesel powered vehicle fuelled by soybean biodiesel blends (B3-B20) with ethanol as an additive (B20E2-B20E5)

The effects of diesel oil-soybean biodiesel blends on a passenger vehicle exhaust pollutant emissions were investigated. Blends of diesel oil and soybean biodiesel with concentrations of 3% (B3), 5% (B5), 10% (B10) and 20% (B20) were used as fuels. Additionally, the effects of anhydrous ethanol as an additive to B20 fuel blend with concentrations of 2% (B20E2) and 5% (B20E5) were also studied. The emissions tests were carried out following the New European Driving Cycle (NEDC). The results showed that increasing biodiesel concentration in the fuel blend increases carbon dioxide (CO₂) and oxides of nitrogen (NO_X) emissions, while carbon monoxide (CO), hydrocarbons (HC) and particulate matter (PM) emissions are reduced. The addition of anhydrous ethanol to B20 fuel blend proved it can be a strategy to control exhaust NO_X and global warming effects through the reduction of CO₂ concentration. However, it may require fuel injection modifications, as it increases CO, HC and PM emissions.     

Variations in oxygenated blend composition to meet energy and combustion characteristics very similar to the diesel fuel

By the method of data collation, research into changes in life histories (ignition delay plus time of combustion) of the compounded fuel droplets (diesel fuel-biodiesel fuel (RME)-bioethanol), as well as diesel engine D-144 brake specific fuel consumption rates was performed and obtained results being compared to diesel fuel by an analogous manner.An optimum composition of the multi-component blend B30 + 7.5E demonstrating specific fuel consumption rates and droplet combustion characteristics very similar to diesel fuel was derived. In comparison to B30, a newly derived combustible blend demonstrated fairly improved emissions of exhaust gases. For low load mode: smoke opacity (−10%), NO_X (−2%), CO (−20%), and HC (−12.5%). For average load mode: smoke opacity (−10%), NO_X (−2%), CO (−22%), and HC (−14.5%). For high load mode: smoke opacity (−18%), NO_X (−2%), CO (−22%), and HC (−18%).     

Combustion, performance and emission characteristics of a DI diesel engine fueled with ethanol-biodiesel blends

In this study, Euro V diesel fuel, biodiesel, and ethanol-biodiesel blends (BE) were tested in a 4-cylinder direct-injection diesel engine to investigate the combustion, performance and emission characteristics of the engine under five engine loads at the maximum torque engine speed of 1800 rpm. The results indicate that when compared with biodiesel, the combustion characteristics of ethanol-biodiesel blends changed; the engine performance has improved slightly with 5% ethanol in biodiesel (BE5). In comparison with Euro V diesel fuel, the biodiesel and BE blends have higher brake thermal efficiency. On the whole, compared with Euro V diesel fuel, the BE blends could lead to reduction of both NO_x and particulate emissions of the diesel engine. The effectiveness of NO_x and particulate reductions increases with increasing ethanol in the blends. With high percentage of ethanol in the BE blends, the HC, CO emissions could increase. But the use of BE5 could reduce the HC and CO emissions as well.     

Spark-ignition engine performance with ‘Powergas’ fuel (mixture of CO/H2): A comparison with gasoline and natural gas

Results are presented of tests from a variable compression ratio Ricardo E6 single-cylinder spark-ignition (SI) engine operating on ‘Powergas’—a synthetic fuel consisting mainly of carbon monoxide and hydrogen. The tests cover a range of air/fuel ratios from rich to the lean operating limit at different speeds and two different compression ratios. Measured results are given for brake torque, brake specific fuel consumption and the concentrations of carbon monoxide (CO), oxides of nitrogen (NO_x) and total unburnt hydro-carbon (THC) emissions in the exhaust gases. Experimental results indicate that ‘Powergas’ produces about 20 and 30% lower engine power output than natural gas (NG) and gasoline fuelling respectively under similar operating conditions. For ‘Powergas’, concentrations of THC and CO in the exhaust were negligible, but carbon dioxide (CO₂) and NO_x were found to be higher compared to other fuels. The engine simulation program ISIS has been used to simulate some of the exhaust emissions and the results show agreement with the experimental values and help explain the experimental results.     

Feasibility of blending karanja vegetable oil in petro-diesel and utilization in a direct injection diesel engine

Karanja (Pongamia pinnata) oil, a non-edible high viscosity (27.84 cSt at 40 °C) straight vegetable oil, was blended with conventional diesel in various proportions to evaluate the performance and emission characteristics of a single cylinder direct injection constant speed diesel engine. Diesel and karanja oil fuel blends (5%, 10%, 15%, and 20%) were used to conduct short-term engine performance and emission tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over the entire range of engine operation and engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature, and exhaust emissions (smoke, CO, CO₂, HC, NO_x, and O₂) were recorded. The brake specific energy consumption (BSEC), brake thermal efficiency (BTE), and exhaust emissions were evaluated to determine the optimum fuel blend. Higher BSEC was observed at full load for neat petro-diesel. A fuel blend of 10% karanja oil (KVO10) showed higher BTE at a 60% load. Similarly, the overall emission characteristics were found to be best for the case of KVO10 over the entire range of engine operation.     

Performance of compression ignition engine with mahua (Madhuca indica) biodiesel

The performance of biodiesel obtained from mahua oil and its blend with high speed diesel in a Ricardo E6 engine has been presented in this paper together with some of its fuel properties. These properties were found to be comparable to diesel and confirming to both the American and European standards. Engine performance (brake specific fuel consumption, brake thermal efficiency and exhaust gas temperature) and emissions (CO, smoke density and NO_x) were measured to evaluate and compute the behaviour of the diesel engine running on biodiesel. The reductions in exhaust emissions and brake specific fuel consumption together with increase brake power, brake thermal efficiency made the blend of biodiesel (B20) a suitable alternative fuel for diesel and thus could help in controlling air pollution.     

Experimental investigation of diesel engine performance and emission characteristics using jojoba/diesel blend and sunflower oil

Experimental study has been carried out to investigate performance parameters, emissions, cylinder pressure, exhaust gas temperature (T_exhaust) and engine wall temperatures (T_wall) for direct injection diesel engine. Tests were conducted for sunflower oil (S100) and 20% jojoba oil + 80% pure diesel fuel (B20) in comparison to pure diesel fuel with different engine speeds. S100 and B20 were selected for the study because of its being widely used in Egypt and in the world. Also, series of tests are conducted at same previous conditions with different percentage of exhaust gas recirculation (EGR) from 0% to 12% of inlet mass of air fresh charge. Results indicate that S100 or B20 gives lower brake thermal efficiency (η_B), brake power (BP), brake mean effective pressure (BMEP), and higher brake specific fuel consumption (BSFC) due to lower heating value compared to pure diesel fuel. S100 or B20 gives lower NO_X concentration due to lower gas temperature. S100 or B20 gives higher T_wall and T_exhaust due to incomplete combustion inside engine cylinder. S100 or B20 gives higher CO and CO₂ concentrations due to higher carbon/hydrogen ratio. The position of maximum pressure (P_max) change for pure diesel fuel is earlier than for S100 or B20. The results show that S100 or B20 are promising as alternative fuel for diesel engine. The utilization of vegetable oils does not require a significant modification of existing engines. This can be seen as the main advantage of vegetable oils. The main disadvantages of biodiesel fuels are high viscosity, drying with time, thickening in cold conditions, flow and atomization characteristics.     

Performance, emission and combustion evaluation of soapnut oil-diesel blends in a compression ignition engine

Soapnut (Sapindus mukorossi) oil, a nonedible straight vegetable oil was blended with petroleum diesel in various proportions to evaluate the performance and emission characteristics of a single cylinder direct injection constant speed diesel engine. Diesel and soapnut oil (10%, 20%, 30% and 40%) fuel blends were used to conduct short-term engine performance and emission tests at varying loads in terms of 25% load increments from no load to full loads. Tests were carried out for engine operation and engine performance parameters such as fuel consumption, brake thermal efficiency, and exhaust emissions (smoke, CO, UBHC, NO_x, and O₂) were recorded. Among the blends SNO 10 has shown a better performance with respect to BTE and BSEC. All blends have shown higher HC emissions after about 75% load. SNO 10 and SNO 20 showed lower CO emissions at full load. NO_x emission for all blends was lower and SNO 40 blend achieved a 35% reduction in NO_x emission. SNO 10% has an overall better performance with regards to both engine performance and emission characteristics.     

Diesel engine performance and emission evaluation using emulsified fuels stabilized by conventional and gemini surfactants

Diesel engines exhausting gaseous emission and particulate matter have long been regarded as one of the major air pollution sources, particularly in metropolitan areas, and have been a source of serious public concern for a long time. The emulsification method is not only motivated by cost reduction but is also one of the potentially effective techniques to reduce exhaust emission from diesel engines. Water/diesel (W/D) emulsified formulations are reported to reduce the emissions of NO_x, SO_x, CO and particulate matter (PM) without compensating the engine’s performance. Emulsion fuels with varying contents of water and diesel were prepared and stabilized by conventional and gemini surfactant, respectively. Surfactant’s dosage, emulsification time, stirring intensity, emulsifying temperature and mixing time have been reported. Diesel engine performance and exhaust emission was also measured and analyzed with these indigenously prepared emulsified fuels. The obtained experimental results indicate that the emulsions stabilized by gemini surfactant have much finer and better-distributed water droplets as compared to those stabilized by conventional surfactant. A comparative study involving torque, engine brake mean effective pressure (BMEP), specific fuel consumption (SFC), particulate matter (PM), NO_x and CO emissions is also reported for neat diesel and emulsified formulations. It was found that there was an insignificant reduction in engine’s efficiency but on the other hand there are significant benefits associated with the incorporation of water contents in diesel regarding environmental hazards. The biggest reduction in PM, NO_x, CO and SO_x emission was achieved by the emulsion stabilized by gemini surfactant containing 15% water contents.     

Performance and emission characteristics of an CI engine fueled with diesel–biodiesel–bioethanol blends

The paper presents the experimental results obtained concerning performances and pollution of a diesel engine fueled with diesel–biodiesel–ethanol blends compared with diesel fuel in laboratory tests. The main properties of the researched fuels are presented within this paper, in comparison with classical diesel fuel (chemical composition, density, kinematic viscosity, cold filter plugging point, flash point). Engines’ performances were evaluated by determining the brake specific fuel consumption and brake thermal efficiency. For pollution evaluation the emissions of CO, CO₂, NO_x, HC and smoke have been measured. An increasing of brake specific fuel consumption has been observed, especially at lower engines’ loads, with maximum 32.4%, reducing engine brake thermal efficiency with maximum 21.7%. CO emissions decrease, especially at high loads with maximum 59%, on the basis of CO₂ increased emissions. NO_x emissions slightly increase, especially at partial and high loads, meanwhile HC and smoke emissions decrease in all engines’ load cycles.     

Experimental study on diesel engine nitrogen oxide reduction running with jojoba methyl ester by exhaust gas recirculation

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is a very good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were made in two sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME are determined and compared. Secondly, tests were performed at two speeds and loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Also, effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light duty diesel engines. A better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5-15% with very little economy penalty.     

Experimental investigation on a C.I. engine using orange oil and orange oil with DEE

In the present work, the effect of using neat orange oil, optimum orange oil-diesel blend and the optimum flow rate of DEE with orange oil are evaluated for the performance, emissions and combustion characteristics of a single cylinder, diesel engine. The experimental results show that carbon monoxide (CO), hydrocarbon (HC) and smoke emissions decrease while oxides of nitrogen (NO_x) emissions increase for orange oil and its blends compared to diesel fuel and DEE with orange oil. The brake thermal efficiency in the case of DEE with orange oil is higher than that of orange oil, orange oil-diesel fuel blend and diesel fuel. The peak cylinder pressure and heat release rate for DEE with orange oil are higher than those of diesel fuel operation.     

Experimental investigation of mineral diesel fuel, GTL fuel, RME and neat soybean and rapeseed oil combustion in a heavy duty on-road engine with exhaust gas aftertreatment

The effects of mineral diesel fuel, gas-to-liquid fuel, rapeseed methyl ester, neat soybean and neat rapeseed oil on injection, combustion, efficiency and pollutant emissions have been studied on a compression ignition heavy duty engine operated near full load and equipped with a combined exhaust gas aftertreatment system (oxidation catalyst, particle filter, selective catalytic NO_x reduction). In a first step, the engine calibration was kept constant for all fuels which led to differences in engine torque for the different fuels. In a second step, the injection duration was modified so that all fuels led to the same engine torque. In a third step, the engine was recalibrated in order to keep the NO_x emissions at an equal level for all fuels (injection pressure, injection timing, EGR rate). The experiments show that the critical NO_x emissions were higher (even behind the exhaust gas aftertreatment systems) for oxygenated fuels in case of the engine not being recalibrated for the fuel. GTL and the oxygenated fuels show lower emissions for some pollutants and higher efficiency after recalibration to equal NO_x levels.     

Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine

Non-edible filtered high viscous (72 cSt at 40 °C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO₂, HC, NO_x, and O₂) were recorded. The optimum engine operating condition based on lower brake specific fuel consumption and higher brake thermal efficiency was observed at 100% load for neat biodiesel. From emission point of view the neat POME was found to be the best fuel as it showed lesser exhaust emission as compared to HSD.     

Comparison of emissions of a direct injection diesel engine operating on biodiesel with emulsified and fumigated methanol

Biodiesel is an alternative fuel for internal combustion engines. It can reduce carbon monoxide (CO), hydrocarbon (HC) and particulate matter (PM) emissions, compared with diesel fuel, but there is also an increase in nitrogen oxides (NO_x) emission. This study is aimed to compare the effect of applying a biodiesel with either 10% blended methanol or 10% fumigation methanol. The biodiesel used in this study was converted from waste cooking oil. Experiments were performed on a 4-cylinder naturally aspirated direct injection diesel engine operating at a constant speed of 1800 rev/min with five different engine loads. The results indicate a reduction of CO₂, NO_x, and particulate mass emissions and a reduction in mean particle diameter, in both cases, compared with diesel fuel. It is of interest to compare the two modes of fueling with methanol in combination with biodiesel. For the blended mode, there is a slightly higher brake thermal efficiency at low engine load while the fumigation mode gives slightly higher brake thermal efficiency at medium and high engine loads. In the fumigation mode, an extra fuel injection control system is required, and there is also an increase in CO, HC and NO₂ (nitrogen dioxide) and particulate emissions in the engine exhaust, which are disadvantages compared with the blended mode.     

Experimental study of the performance and emission characteristics of diesel engine using direct and indirect injection systems and different fuels

An experimental study of the performance and emission characteristics of diesel engine using direct and indirect injection combustion systems are carried out on a same model of two diesel engines fuelled with diesel and the blend of diesel and Chinese pistache biodiesel. The results show that the NO_x emissions from the indirect injection combustion system (ICS) fuelled with diesel are reduced by around two thirds, compared to that from direct injection combustion system (DCS). Smoke emissions from the engine using ICS are all significantly lower than that of DCS, reduced by 70% for diesel; by 50-60% for the blend. The brake thermal efficiencies (BTEs) reduced by 8-10%, compared to that of DCS; the fuel consumptions increased by around 7-9%. It is also found that carbon monoxide (CO) emissions are reduced when the engine run at engine high power outputs, so are the hydrocarbon (HC) emissions from ICS at the peak power outputs. It is found that, when fuelled with the blend, the effects of ICS to the performance and emissions of diesel engine are very similar to that of running with diesel. For ICS engine fuelled with diesel and the blend fuel, the BSFCs for the blend are around 5% higher; the BTEs are around 2-4% lower; the reductions of NO_x from the blend fuel are 5.1-8.4% on average for the ICS; the reductions of smoke from the blend fuel are 26.8-31.7% on average for the ICS. CO emissions are around a half lower; and HC emissions are around one fifth lower, compared to that of fuelling with diesel. Comparing to that of DCS fuelled with diesel, using ICS fuelled with the blended fuel has much lower emissions. NO_x emissions decreased by 65.6% and 66.1%; smoke emissions decreased by 75.7% and 80.2%; CO emissions decreased by 55.8% and 46.0%; HC emissions decreased by 24.9% and 18.9%; with the BSFCs around 14.6-14.9% higher and the BTEs around 9.7-10.0% lower.     

Comparative evaluation of performance and emission characteristics of jatropha, karanja and polanga based biodiesel as fuel in a tractor engine

Non-edible jatropha (Jatropha curcas), karanja (Pongamia pinnata) and polanga (Calophyllum inophyllum) oil based methyl esters were produced and blended with conventional diesel having sulphur content less than 10 mg/kg. Ten fuel blends (Diesel, B20, B50 and B100) were tested for their use as substitute fuel for a water-cooled three cylinder tractor engine. Test data were generated under full/part throttle position for different engine speeds (1200, 1800 and 2200 rev/min). Change in exhaust emissions (Smoke, CO, HC, NO_x, and PM) were also analyzed for determining the optimum test fuel at various operating conditions. The maximum increase in power is observed for 50% jatropha biodiesel and diesel blend at rated speed. Brake specific fuel consumptions for all the biodiesel blends with diesel increases with blends and decreases with speed. There is a reduction in smoke for all the biodiesel and their blends when compared with diesel. Smoke emission reduces with blends and speeds during full throttle performance test.