C-S-H纳米晶核对矿物掺合料复合胶凝材料水化性能的影响研究

水泥中掺入大量矿物掺合料易造成其早期强度低、施工周期长等问题。本文研究了C-S-H晶核对含矿物掺合料的复合胶凝材料体系水化性能的影响规律;通过热力学计算阐述了C-S-H晶核降低水化产物成核势垒的机理,并通过离子溶出与沉积探讨大掺量矿物掺合料胶凝体系水化机理。结果表明：矿物掺合料复合胶凝材料体系水化能力较弱,这是由于Ca²⁺溶出受到制约,C₃S的水化反应缓慢;当加入晶核后,水泥中硅酸盐相溶解-结晶能力得到大幅提升,使得矿物掺合料水泥体系的水化反应活性接近纯水泥体系。研究表明,C-S-H晶核可解决大掺量矿物掺合料胶凝体系所带来的水化能力严重不足问题。     

Early Hydration of Tricalcium Silicate

The hydration of tricalcium silicate (C₃S) in the preacceleration stages was studied. The C₃S particles carry a positive charge during the early stages of hydration. Following a rapid hydrolysis of C₃S, calcium ions adsorbed on the Si-rich surface of C₃S particles, greatly reducing their further dissolution, thus initiating the induction period. The [Ca²⁺] and [OH^-] continue to increase at lower rates and, because Ca(OH)₂ crystal growth is inhibited by silicate ions, become supersaturated with respect to Ca(OH)₂. When the supersaturation reaches a value of ∼1.5 to 2.0 times the saturation concentration, nuclei are formed, and rapid growth of Ca(OH)₂ and C-S-H is initiated. These products act as sinks for the ions in solution, thus enhancing the further dissolution of C₃S.     

Chemical Composition of C-S-H Gel Formed in the Hydration of Calcium Silicate Pastes

The chemical and physical compositions of C-S-H formed in paste hydration of C₃S cured at 4°, 25°, and 65°C and of C₂S and a C₃S/C₂S blend cured at 25°C were studied using quantitative X-ray diffraction analysis (QXDA), extraction, and thermal effluent gas analysis (TEGA) to determine the free CH content. The amount of CH determined by extraction is greater than or equal to that determined by QXDA. The difference between the two results increased with the H₂O surface area of the paste, indicating the existence of adsorbed CH in the form of Ca²⁺ and (OH)⁻ ions which cannot be measured by QXDA and suggesting that the extraction method is better for estimating the composition of C-S-H.     

Influence of Minor Ions on the Stability and Hydration Rates of β-Dicalcium Silicate

The effects of Al³⁺, B³⁺, P⁵⁺, Fe³⁺, S⁶⁺, and K⁺ ions on the stability of the β-phase and its hydration rate were studied in reactive dicalcium silicate (C₂S, Ca₂SiO₄) synthesized using the Pechini process. In particular, the dependences of the phase stability and degree of hydration on the calcination temperature (i.e., particle size) and the concentration of the stabilizing ions were investigated. The phase evolution in doped C₂S was determined using XRD, and the degree of hydration was estimated by the peak intensity ratio of the hydrates to the nonhydrates in ²⁹Si MAS NMR spectra. The stabilizing ability of the ions varied significantly, and the B³⁺ ions were quite effective in stabilizing the β-phase over a wide range of doping concentrations. The hydration results indicated that differently stabilized β-C₂S hydrated at different rates, and Al³⁺- and B³⁺-doped C₂S exhibited increased degree of hydration for all doping concentration ranges investigated. The effect of the doping concentration on degree of hydration was strongly dependent on the stabilizing ions.     

镁渣晶体结构对脱硫活性影响实验

研究了激冷水合过程中镁渣晶体结构的变化,结合钙转化率研究了晶体结构对镁渣脱硫活性的影响。借助X射线衍射和透射电镜分析了镁渣的晶体结构和形貌特征。结果表明：β-C₂S中的Ca²⁺配位不规则是其水合活性高于γ-C₂S的原因。随着镁渣激冷温度升高,β-C₂S增加,促进了具有发达孔隙结构的C－S－H生成,提高了物理吸附能力;晶粒细化程度增大,晶胞参数变化引起的晶格缺陷增多,增强了化学吸附能力。950℃激冷温度下镁渣脱硫活性最高,钙转化率达到24.6%。     

Thermal stability of ettringite in alkaline solutions at 80 °C

The thermal stability of synthetic ettringite was examined in NaOH solutions up to 1 M after 12 h of heat treatment at 80 °C, with or without the coexistence of C₃S in the system. Ettringite was found to convert to the U phase, a sodium-substituted AFm phase, over the heat treatment in the absence of C₃S. The presence of C₃S, leading to C-S-H formation, prevents the U phase formation and results in the conversion of ettringite to monosulfate. Sulfate ions generated from ettringite decomposition mostly remain in the solution, but some is incorporated into C-S-H. During subsequent storage at room temperature, the majority of monosulfate slowly converts back to secondary ettringite under moist conditions, using the supply of sulfate ions from the solution and C-S-H. The observations support the current mechanism of delayed ettringite formation (DEF).     

C-S-H/PCE凝胶对掺磷渣水泥的低温促凝早强性能研究

探讨C-S-H/PCE凝胶对掺磷渣硅酸盐水泥的低温促凝早强性能的影响,并通过上清液pH值、Ca²⁺浓度和化学结合水量分析其对水化的影响机理。低温下(8℃) C-S-H/PCE凝胶能有效缩短混凝土终凝时间,并提高早期强度,当掺量5%时,混凝土终凝时间缩短近6 h,16 h、24 h和3 d抗压强度比分别为160%、150%和110%,且不影响2.5 h混凝土工作性能。C-S-H/PCE凝胶能使低温下掺磷渣硅酸盐水泥浆体处于高pH状态,加速早期水泥矿相离子溶解,提高Ca²⁺过饱和度,加速后期析晶过程,提高化学结合水量,从而促进掺磷渣硅酸盐水泥的水化,实现低温促凝早强。     

硫铝酸钙的氧化铝溶出性能

使用分析纯CaCO₃、Al₂O₃与CaSO₄·2H₂O配料,在1375℃、保温2 h的条件下合成了纯物相硫铝酸钙3CaO·3Al₂O₃·CaSO₄（C₄A₃S）,对其物相组成和微观形貌进行了表征。并探究了碳碱浓度、苛碱浓度、溶出温度、溶出时间、粒度等因素对C₄A₃S氧化铝溶出性能的影响。结果表明：C₄A₃S的氧化铝溶出性能随着碳碱与苛碱浓度的增加先提高,之后趋于稳定。粒度越小,溶出率越高。与七铝酸十二钙12CaO·7Al₂O₃（C₁₂A₇）相比,C₄A₃S的孔洞状结构使其氧化铝更易溶出,在10 min时氧化铝溶出率即达到98%以上,且溶出所需的碳碱浓度与溶出温度均低于C₁₂A₇。在最佳条件：碳碱80 g·L^-1、苛碱10 g·L^-1、溶出温度80℃、溶出时间10 min下,C₄A₃S的氧化铝溶出率为98.76%。     

Adsorption equilibrium,kinetics, and dynamic separation of Ca2+ and Mg2+ ions from phosphoric acid-nitric acid aqueous solution by strong acid cation resin

The separation of Ca²⁺ and Mg²⁺ ions from phosphoric acid-nitric acid aqueous solution is very significant for the neutralization process of nitrophosphate fertilizer. This paper studied the adsorption equilibrium, kinetics, and dynamic separation of Ca²⁺ and Mg²⁺ ions by strong acid cation resin, and the effects of phosphoric acid and nitric acid on the adsorption process were investigated. The results reveal that the adsorption process of Ca²⁺ and Mg²⁺ ions in pure water on resin is in good agreement with the Langmuir isotherm model and their maximal adsorption capacities are 1.86 mmol·g^-1 and 1.83 mmol·g^-1, respectively. The adsorption kinetics of Ca²⁺ and Mg²⁺ ions on resin fits better with the pseudo-first-order model, and the adsorption equilibrium in pure water is reached within 10 min contact time, while at the present of phosphoric acid, the adsorption rate of Ca²⁺ and Mg²⁺ ions on resin will go down. The dynamic separation experiments demonstrate that the designed column adsorption is able to undertake the separation of metal ions from the mix acids aqueous solution, but the dynamic operation should control the flow rate of mix acid solution. Besides nitric acid solution was proved to be effective to completely regenerate the spent resin and achieve the recyclable operation of separation process.     

Early hydration of large single crystals of tricalcium silicate

A reaction product believed to be an initial hydrate layer was observed to have formed on large pure C₃S single crystals after 5 minutes of hydration. This layer then increased in thickness and became covered with micrometer-sized spheres of poorly crystallized Ca(OH)₂ within 30 minutes. Subsequently, the formation of a new hydrate of acicular morphology was observed to occur on the surface of the first-formed hydrate. This transformation was accompanied by the disappearance of the first hydrate layer and the calcium hydroxide spheres. The observation of a transient initial hydrate is in accord with the view that the rate of early C₃S hydration is controlled by the formation and subsequent disappearance of a barrier layer.     

水泥矿物体系诱导期的水化进程及机理的研究进展

硅酸三钙(C₃S)体系及铝酸三钙-二水石膏(C₃A-CH₂) 体系作为主要的硅酸盐水泥矿物相,对水泥新拌阶段及后续性能发展阶段有尤为重要的影响。而水泥在诱导期内的水化进程很大程度上决定了其后续性能的发展。鉴于此,本文回顾了水泥水化的热力学原理,重点综述了目前关于水泥水化诱导期开始及结束时作为主要矿物体系的C₃S体系和C₃A-CH₂体系的水化进程及机理的研究进展,以及不同矿物体系诱导期的成因。但限于目前的研究手段,对于水泥水化诱导期内各种矿物体系的相互作用和相互影响仍未完全厘清,还需要进一步的探索。     

Si NMR Study of the Hydration of Ca3SiO5 and ß-Ca2SiO4 in the Presence of Silica Fume

²⁹Si magic-angle spinning nuclear magnetic resonance (MASNMR) was used to study the room-temperature hydration of C₃S, ß-C₂S, and reactive ß-C₂S mixed with different amounts of silica fume (SF) that had been hydrated up to nine months and longer. The overall CaO:SiO₂ molar ratios of the mixes were 0.12, 0.20, 0.35, 0.50, and 0.80. NMR spectroscopy was used to quantify the remaining starting materials and the resulting hydration products of different species. A broad peak assigned to Q³, appearing in both the fourier transform (FT) and the cross-polarization (CP) modes, increased in intensity with increased SF content and with age. This Q³ species was attributed to two sources: (1) the surface hydroxylation of SF and (2) the cross-linking of dreierketten (chains of silicate tetrahedra arranged in a repeating three-unit conformation) in the calcium silicate hydrate (C-S-H) structure. A Q⁴ species also appeared in the CP spectra of samples with large SF additions after extended hydration and was attributed to cross-polarization by adjacent hydroxylated Q³ species at the surface of amorphous SiO₂.     

Characterization of C-S-H from Highly Reactive β-Dicalcium Silicate Prepared from Hillebrandite

β-dicalcium silicate synthesized by thermal dissociation of hydrothermally prepared hillebrandite (Ca₂(SiO₃)(OH)₂) exhibits extremely high hydration activity. Characterization of the hydrates obtained and investigation of the hydration mechanism was carried out with the aid of trimethylsilylation analysis, ²⁹Si magic angle spinning nuclear magnetic resonance, transmission electron microscopy selected area electron diffraction, and XRD. The silicate anion structure of C-S-H consisted mainly of a dimer and a single-chain polymer. Polymerization advances with increasing curing temperature and curing time. The C-S-H has an oriented fibrous structure and exhibits a 0.73-nm dreierketten in the longitudinal direction. On heating, the C-S-H dissociates to form β-C₂S. The temperature at which βC₂S begins to form decreases with increasing chain length of the C-S-H or as the Ca/Si ratio becomes higher. The high activity of β-C₂S is due to its large specific surface area and the fact that the hydration is chemical-reaction-rate-controlled until its completion. As a result, the hydration progresses in situ and C-S-H with a high Ca/Si ratio is formed.     

CCUS环境下水泥单矿C3S的CO2腐蚀动力学研究

在碳捕集、利用和封存(CCUS)井下,油井水泥因长期受井下高温、高压和高酸性流体的作用会遭受碳化腐蚀导致水泥环失效。为了模拟CO₂地质封存井下碳化腐蚀环境,本文将油井水泥的主要单相矿物硅酸三钙(C₃S)置于不同温度(30 ℃、60 ℃、90 ℃),并密封在8.0 MPa的气相或液相的CO₂碳化环境下,采用XRD和TGA相结合的分析方法,分析水泥单矿C₃S受CO₂腐蚀环境的影响规律。根据非稳态Fick扩散的渗透理论模型,建立腐蚀产物定量分析结果与腐蚀龄期的数学模型,拟合得到C₃S受CO₂腐蚀后的产物生成系数,以此评价不同CO₂腐蚀因素对C₃S的影响程度。结果表明:在CO₂气相环境中,温度升高将显著加剧对C₃S的腐蚀且产生溶蚀现象;而在CO₂液相环境下,高温(90 ℃)使C₃S水化反应加剧并形成阻滞层,降低CO₂对C₃S的腐蚀速率。     

The morphology and composition of an immature C3S paste

The morphology of a one month old hydrated C₃S paste has been studied using the scanning electron microscope (SEM) and preferential etching techniques. The C/S ratios of the calcium silicate hydrates (CSH) have been determined using the SEM with an energy dispersive spectrometer. The hydrate rims covering the partially hydrated C₃S grains were found to consist of two layers; an outer porous product with an acicular morphology having a C/S ratio of 1.6 ± 0.1 and an inner product with a C/S ratio of 1.90 ± 0.05.

A region of increased C/S ratio in the C₃S core at the C₃S-CSH interface is attributed to a depletion of SiO₂ resulting from the diffusion of Si⁴⁺ ions into the hydrate.     

Evidence of calcium silicoaluminates in hydrated mixtures of tricalcium silicate and tricalcium aluminate

Calcium monosilicoaluminate C₃A·CaSiO₃·12 H₂O and calcium trisilicoaluminate C₃A·3 CaSiO₃·31 H₂O have been identified in pastes of C₃S + C₃A. Electron probe microanalysis and scanning electron microscopy with energy X-ray dispersive analysis show that silicoaluminates are both formed around C₃A grains by diffusion of silicate ions from C₃S grains through solution. In samples containing gypsum, these silicate ions diffuse through the sulfoaluminate zone.     

Crystal lattice defects in di-calcium silicate

It is well documented that the impurity content of C₂S has a marked effect on its hydration properties. It is also a fact that pure C₂S at room temperature exists in a crystal configuration, γ, which is completely different from the clinker C₂S. Incorporation of impurity ions into pure C₂S inhibits the β → γ transition on cooling, even at impurity levels as low as 0.1%. Currently, there is no fully accepted model for the mechanism of the stabilization of the β phase over the γ phase by impurities. The presence of these trace impurities naturally raises the question of the location and role of the impurities in producing this marked stabilizing effect. A quantitative solution to this problem requires that the lattice defect disorder of C₂S be defined and related to the phase stabilization properties of the impurities. Definition of crystal defect disorder can be achieved through detailed measurements of the electrical conductance of the solid with the data being interpreted in terms of solid state physics. Data for the electrical conductance of pure and “intentionally” impure (doped) C₂S over the temperature range 300 to 1100°C is presented. These data are interpreted in terms of crystal defects, their formation, location and kinetics. Models are presented to account for the stabilizing action of impurity ions within the crystal lattice of C₂S.     

Highly Reactive β-Dicalcium Silicate: III, Hydration Behavior at 40–80°C

The effect of curing temperature (40°, 60°, 80°C) on the hydration behavior of β-dicalcium silicate (β-C₂S) was investigated. The β-C₂S was obtained by decomposition of hillebrandite, Ca₂(SiO₃)(OH)₂, at 600°C, has a specific surface area of about 7 m²/g, and is in the form of fibrous crystals. The dependence of the hydration reaction on temperature continues until the reaction is completed. The hydration is completed in 1 day at 80°C and in 14 days at 14°C. The hydration mechanism is different above and below 60°C, but at a given temperature, the reaction mechanism and the silicate anion structures of C-S-H do not change significantly from the initial to the late stages of the reaction. High curing temperature and long curing times after completion of reaction promote silicate polymerization. The Ca/Si ratio of C-S-H shows high values, being almost 2.0 above 60°C and 1.95 below 40°C.     

Elucidation of a preparation method for copper ion-exchanged ZSM-5 samples exhibiting extremely efficient N2-adsorption at room temperature: effect of counter ions in the exchange solution

The adsorption of N₂ on a copper ion-exchanged ZSM-5 sample (CuZSM-5) prepared by ion exchange using an aqueous solution of copper propionate, Cu(C₂H₅COO)₂, was examined at room temperature by measuring the FT-IR spectra, adsorption isotherms and heat of adsorption. This sample was found to be extremely efficient in terms of N₂ adsorption with regard to both the amount and the energy (i.e., heat) of adsorption, compared with samples prepared by a conventional ion-exchange method using an aqueous solution involving Cu²⁺ and simple counter ions, Cl⁻ or NO₃⁻. To clarify the specificity of the newly-prepared sample, the ion-exchange of ZSM-5 with Cu²⁺ was carried out by employing aqueous solutions involving Cu²⁺ and various types of counter ions [propionate (C₂H₅COO⁻), acetate (CH₃COO⁻), formate (HCOO⁻), chloride (Cl⁻) and nitrate (NO₃⁻) ions]. When the ion exchange was performed by using a Cu(C₂H₅COO)₂ or Cu(CH₃COO)₂ solution, the Cu²⁺ species with propionate or acetate ligand (in the monomer state) were ion-exchanged in ZSM-5, as confirmed by the DR, EPR and FT-IR spectra for CuZSM-5. In contrast, Cu²⁺ species were present in the form of aquo-complexes in samples prepared with other solutions. This distinct difference can be ascribed to the difference in the pK_a values of the counter ions; carboxylate ions, with a high pK_a value, are inclined to form a complex with Cu²⁺. Using this newly applied Cu(C₂H₅COO)₂ solution, the present ion-exchange method has the potential to develop new effective materials that possess the specific adsorption and catalytic properties of CuZSM-5.     

过氧化氢溶液中痕量离子吸附分离用氨基功能化SBA-15的制备及性能

通过后接枝法制备了氨基功能化SBA-15介孔氧化硅(S-N),用于吸附过氧化氢溶液中的金属和阴离子及有机杂质制高纯过氧化氢.研究了接枝量对吸附剂结构和性能的影响并发现S-N中的氮含量随接枝剂用量增加而增加,最高为1.83％.S-N保留了高度有序的六方孔道结构,但比表面积和孔体积均随接枝量增加而下降.在过氧化氢溶液中,各...