共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
粉末喷涂系统的过程控制 总被引:1,自引:0,他引:1
粉末喷涂系统的过程控制,广义地分,主要有四类:喷枪移动、喷枪启动、火焰检测和喷粉室/回收系统监控。喷枪移动装置如振荡器、往复装置、自动装置,一般都已了解,这里不再赘述。本文着重叙述近年来已经进展很大的后面三项。 相似文献
3.
目前,大陆大多数火焰喷涂设备主要用于金属喷涂的零部件维修和预保护涂层,喷枪送粉结构单一,无法满足大型构件防腐现场喷涂需要。作者黎明先生在本文中对火焰喷塑涂层用途、原理及特点,喷涂参数及工艺等方面作了详尽的阐述。 相似文献
4.
5.
6.
静电粉末喷涂的故障、原因和排除方法 总被引:1,自引:1,他引:0
故障故障原因排除方法喷涂过程中发生1.不喷粉(1)喷枪开关失灵。(2)供粉器内无粉或粉量太少。(3)输粉管堵塞。(4)吸粉管件松动漏气或脱落。(5)供粉振荡器故障。(6)流化床虹吸法供料器的压力调得过低。(1)修理。(2)加入粉。(3)输通。(4)修... 相似文献
7.
8.
漫反射光电开关用于粉末喷涂设备改造,可准确控制停粉操作,从而节省涂料,减轻操作者的劳动强度,改善工作环境. 相似文献
9.
列举了粉末喷涂过程设备逸粉的危害,提出粉末喷涂设备设计要“五位一体”统筹考虑的设计思想,并从设备选型、设备设计、设备管理、设备改造诸方面提出防止粉末外逸的解决方案。 相似文献
10.
11.
分享了海沃氏使用先进涂装设备提高生产效率的经验:快速换色粉房ColorMax系统的使用使整个换色时间由1 h减少到4 min 20 s,Encore粉末喷枪的应用克服了传统喷枪存在的粉末涂出量、带电效果及雾化效果不稳定的问题,单级回收粉房的应用使粉末上粉率达到98%以上。新设备工艺技术的使用在提升产品品质的同时有效地控制了生产成本。 相似文献
12.
13.
影响粉末涂料涂膜质量因素的探讨 总被引:1,自引:0,他引:1
介绍了粉末涂料的喷涂原理、喷涂工艺流程,研究了粉末粒径、前处理、涂层厚度、喷涂工艺参数、固化温度以及喷涂环境对涂膜质量的影响。结果表明:前处理工艺参数对涂膜品质影响较大。控制粉末粒径在20-80μm,调整适宜的喷涂参数(30.90kV的静电压,0、01~0.1kV的雾化气压和0.
2—0.4MPa的供粉气压),在喷嘴距离为200—250mm下.于空气湿度不高于85%的涂装环境中.对经过前处理后之工件进行涂装,使涂层厚度为60—90μm,视涂层化学成分分别于160—200℃的温度下烘烤20min,可以获得外观好、物理机械性能优良的涂膜。 相似文献
14.
介绍在团粒法工艺的基础上 ,将尿素熔融成尿液或用尿素车间二段蒸发器的尿液进行喷浆造粒生产复合肥的改造方案、改造内容、改造效果和投资情况。 相似文献
15.
Pierre Schuck Romain Jeantet Bhesh Bhandari Xiao Dong Chen Ítalo Tuler Perrone Antônio Fernandes de Carvalho 《Drying Technology》2016,34(15):1773-1790
Milk is extremely perishable, and yet it has to be preserved for later consumption. In this view, membrane filtration, vacuum concentration lactose crystallization, homogenization, and spray-drying dehydration are valuable techniques to stabilize most dairy ingredients. Considering the increasing development of dairy trade, there is a need for the dairy industry to improve its understanding of how these concentration and spray-drying processes affect the quality of the resulting dairy powders, so to control it. However, the residence time of the droplet and the powder in the spray dryer is so short that it is very difficult to implement studies on the mechanisms of the structural changes in the protein without fundamental research into the process/product interactions. Moreover, several authors have reported the crucial and specific role of dairy components in the mechanisms of water transfer during drying and rehydration. The aim of this paper is to review the present and recent advances in knowledge and innovations, on the properties of spray-dried dairy products, on the modeling and simulation of water transfer processes (drying and rehydration), and on spray-drying equipment and energy consumption. 相似文献
16.
The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate. 相似文献
17.
18.
介绍了杀虫双干燥制粉工艺流程,并对装置中的一些问题提出了改进措施,经济性分析表明杀虫双粉剂的生产效益非常显著。 相似文献
19.
20.
介绍了几种静电喷粉快速换色方法,采用滤芯回收系统可解决喷粉快速换色,阐述滤芯分离粉尘的机理,以及滤芯的性能要求,讨论了集中滤芯回收系统和分体式滤芯侧回收系统的工作原理及其应用。 相似文献