Influence factors analysis of removing heavy metals from multiple metal-contaminated soils with different extractants

Some key factors on the heavy metals removal efficiencies were studied when soil washing technology was used in the remediation of soils contaminated by multiple heavy metals. The results show that the dissolubilities of Cu and Zn are promoted by humic acids, but Pb and Cd are inhibited by humic acids; heavy metals in the clay are more difficult to be extracted than silt; the strong acidic soils can cause the protonation of EDTA and weaken its extracting ability; EDTA is effective for extracting Pb and Cd, while oxalate (OX) is effective for extracting Cu and Zn; and biosurfactant can be used as additive to improve the removal of some particular heavy metals. Foundation item: Project(20050532009) supported by the Doctoral Foundation of Ministry of Education of China; Projects(2006BAD03A1704, 2006BAD03A1706) supported by the National 11th-Five Technology Supporting Project     

Synthesis and photophysical and electrochemical properties of new cyclometalated platinum complex containing oxadiazole ligand

A new cyclometalated platinum complex containing 2, 5-bis（naphthalene-1-yl）-1,3,4-oxadiazole ligand was synthesized and characterized. The UV-Vis absorptions and photoluminescent properties of the ligand and its platinum complex were investigated A characteristic metal-ligand charge transfer absorption peak at 439 nm in the UV spectrum and a strong emission peak at 625 nm in the photoluminescence spectrum were observed for this complex in dichloromethane. Cyclic voltammtry （CV） analysis shows that the EHOMO （energy level of the highest occupied molecular orbital） and ELUMO （energy level of the lowest unoccupied molecular orbital） of the platinum complex are about -5.69 and -3.25 eV, respectively, indicating that the oxadiazole-based platinum complex has a potential application in electrophosphorescent devices used as a red-emitting material.     

Devitrification behaviour of rapidly solidified Al87Ni7Cu3Nd3 amorphous alloy prepared by melt spinning method

Rapidly solidified Al87Ni7Cu3Nd3 amorphous alloy was prepared by using melt spinning. Its calorimetric behavior was characterized by using differential scanning calorimeter in a continuous or isothermal heating mode. phase transformation was investigated, with a special interest in primary crystallization, by using an in-situ examination of X-ray diffractometry （XRD） and high resolution transmission electron microscopy （HRTEM）. The results show that, the whole devitrification of rapidly solidified Al87NiyCu3Nd3 amorphous alloy involves two main processes of primary crystallization and secondary crystallization that consist mainly of two reactions. For primary crystallization, the apparent activation energies, EIso and EKis and growth activation energies Eg are about 153, 166 and 288 kJ/mol, respectively. The interdiffusion of Al atoms is a rate-controlled step of formation of the a（Al） particles, but slow diffusion of Ni and Nd atoms plays a significant role in retarding growth of the α （Al） particles. For secondary crystallization, EIso, EKis and Eg of the first reaction are about 291,208 and 290 kJ/mol, and those of the second reaction are about 367, 269 and 372 kJ/mol. The two reactions of secondary crystallization are controlled mainly in an interface-controlled three-dimensional mode, depending mainly on slow diffusion of Ni and Nd atoms.     

Synthesis and coloring properties of Cd（S1-xSex） pigments by precipitate-hydrothermal method

Cd（S1-xSex） pigments （red to yellow） were synthesized by precipitate-hydrothermal method. The structure, morphology and hue of the powder were characterized by X-ray diffractometry （XRD）, scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDAX） and CIE chromaticity. The optimum synthesis conditions were obtained and reaction mechanism was further analyzed as well. The results show that molar ratio of S to Se, pH value and hydrothermal reaction conditions have great effects on the hues of the pigments. Pigments with vivid hues are obtained under the conditions that pH value is about 13.0, hydrothermal reaction condition is at 140 ℃ for 4 h or at 160 ℃ for 6 h. The reaction mechanism is that Se^2- of Cd（S1-xSex） substitutes S^2- of CdS and then forms a continuous solid solution.     

First-principles lattice stability of Fe, Ru and Os

Lattice constants, total energies and densities of states of transition metals Fe, Ru and Os with BCC, FCC and HCP structures were calculated by the GGA+PBE functional and the ultrasoft pseudo-potential plane wave method, and compared with those of the first-principles projector augmented wave (PAW) method, CALPHAD method and experimental data. The results show that the lattice stability of this work is ΔG ^BCC-HCP>ΔG ^FCC-HCP>0, agreeing well with those of PAW method in the first-principles and CALPHAD method except for BCC-Fe. And the densities of state of HCP-Ru and Os have an obvious character of stable phase, agreeing completely with the results of the total energy calculations. Further analyses of atomic population show that the transition rate of electrons from s to p state for HCP, FCC and BCC crystals increases from Fe to Os, and a stronger cohesion, a higher cohesive energy or a more stable lattice between atoms of heavier metals are formed. Foundation item: Project(20070533118) supported by the Doctoral Discipline Foundation of Ministry of Education of China; Projects(50471058, 50271085) supported by the National Natural Science Foundation of China; Project supported by the Postdoctoral Foundation of Central South University, China     

Carburization of ferrochromium metals in chromium ore fines containing coal during voluminal reduction by microwave heating

Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the conditions of COFCC with n(O):n(C) (molar ratio) as 1.00:0.84 and n(SiO₂):n(CaO) as 1.00:0.39, the samples were heated by 10 kW microwave power to reach the given temperatures and held for different times respectively. The results show that the low-C-Cr ferrochromium metal phase in the reduced materials forms before the high-C-Cr ferrochromium metal phase does. With increasing temperature the C content of ferrochromium metals is in a positive correlation with the content of Cr. The C content of ferrochromium metal in reduced materials is 0–10.07% with an average value of 4.68%. With the increase of holding time the Cr content in ferrochromium metals is in a negative correlation with the content of C, while the content of Fe changes in the contrary way. In the microwave field the kinetic conditions of carburization are closely related with the temperature of microwave heating, holding time and carbon fitting ratio. Foundation item: Project(50474083) supported by the National Natural Science Foundation of China; Project supported by the Baoshan Iron & Steel Co. Ltd. of China     

Effect of cobalt loading on reducibility, dispersion and crystallite size of Co／Al2O3 Fischer-Tropsch catalyst

Co/Al2O3 Fischer-Tropsch synthesis catalysts with different cobalt loadings were prepared using incipient wetness impregnation method. The effects of cobalt loading on the properties of catalysts were studied by means of X-ray diffraction (XRD), temperature programmed reduction (TPR), hydrogen temperature programmed desorption (H2-TPD) and O2 titration. Co-support compound formation can be detected in catalyst system by XRD.For the Co/Al2O3 catalysts with low cobalt loading, CoAl2O3 phase appears visibly. Two different reduction regions can be presented for Co/Al2O3 catalysts, which belong to Co3 O4 crystallites (reduction at 320 ““C) and cobalt oxidealumina interaction species (reduction at above 400℃). Increasing Co loading results in the increase of Co3 O4 crystallite size. The reduced Co/Al2O3 catalysts have two adsorption sites, and cobalt loading greatly influences the adsorption behavior. With the increase of cobalt loading, the amount of low temperature adsorption is increased, the amount of high temperature adsorption is decreased, and the percentage reduction and cobalt crystallite size are increased.     

First-principle investigation on stability of Co-doped spinel λ-Mn4-xCoxO8

The mechanism of stability of Co-doped spinel λ-MnO2 that is referred to as spinel LixMn2O4 （x=0） was studied by using the first-principle calculation method. The total energy and formation enthalpy can be decreased remarkably due to the Co substation, resulting in a more stable structure ofλ-MnxCr2-xO4. The bond order and DOS analysis were given in detail to explain the nature of stability improvement. The calculated results show that as the content of Co dopant increases, the bond order of Mn-O becomes larger and the peak of density of states around Fermi level shifts toward lower energy. The charge density distribution illustrates that the Mn-O bonding is ionic and partially covalent, and the covalent Mn-O bonding becomes stronger with the increase of Co dopant content. The results confirm that the Co-doping will enhance the stability of λ-MnO2 and hence improve the electrochemistry performance of LixMn2O4.     

Growth kinetics of Thiobacillus ferrooxidans in bioelectrochemical cell

Thiobacillus ferrooxidans might be the most important bacteria used in biometallurgy. The foundation way of its growth process is oxidizing ferrous in order to obtain energy needed for metabolism, but the variation of ferrous concentration and mixed potential of the culture media would have crucial effect on the bacteria growth. Based on the characteristics of Thiobacillus ferroxidans growth and redox potential of ferric and ferrous, an electrochemical cell was designed conventionally to study growth rule and the relationship between redox potential and bacteria growth was built up, and some growth kinetics of Thiobacillus ferrooxidans were elucidated. It demonstrates that the variation of open potential of electrochemical cell ΔE shows the growth tendency of Thiobacillus ferrooxidans, at the initial growth stage, the value of δE increases slowly, when at logistic growth stage, it increases drastically, and the growth rate of bacteria is linear with the oxidation rate of ferrous. The bacteria growth kinetics model is proposed using Monod and Michealis-Menten equation, and the kinetics parameters are got. The consistence of the measured and the calculated results proves that it is proper to use the proposed kinetics model and the electrochemical cell method to describe the growth rule of Thiobacillus ferrooxidans. Foundation item: Project (50204001) supported by the National Science Foundation of China     

Characterization of tricalcium phosphate solubilization by Stenotrophomonas maltophilia YC isolated from phosphate mines

The phosphate solubilizing characteristics of a strain YC, which was isolated from phosphate mines (Hubei, China), were studied in National Botanical Research Institute’s phosphate (NBRIP) growth medium containing tricalcium phosphate (TCP) as sole phosphorus (P) source. The strain YC is identified as Stenotrophomonas maltophilia (S. maltophilia) based upon the results of morphologic, physiological and biochemical characteristics and 16S rRNA sequences analysis. The results show that the strain S. maltophilia YC can solubilize TCP and release soluble P in NBRIP growth medium. A positive correlation between concentration of soluble P and population of the isolate and a negative correlation between concentration of soluble P and pH in the culture medium are observed from statistical analysis results. Moreover, gluconic acid is detected in the culture medium by HPLC analysis. It indicates that the isolate can release gluconic acid during the solubilizing experiment, which causes acidification of the culture medium and then TCP solubilization. S. maltophilia YC has a maximal TCP solubilizing capability when using maltose as carbon source and ammonium nitrate as nitrogen source, respectively, in NBRIP growth medium. Foundation item: Project(2004CB619201) supported by the Major State Basic Research and Development Program of China; Project(Z200515002) supported by the Key Project Foundation of the Education Department of Hubei Province, China; Project(GCP200801) supported by the Open Research Fund of Key Laboratory for Green Chemical Process of Ministry of Education, China; Project(Q200811) supported by the Youths Science Foundation of Wuhan Institute of Technology, China     

Microscopic phase-field simulation for coarsening behavior of L12 and DO22 phases of Ni75Cr x Al25? x alloy

Based on the microscopic phase-field dynamic model and the microelasticity theory, the coarsening behavior of L1₂ and DO₂₂ phases in Ni₇₅Cr _x Al_25−x alloy was simulated. The results show that the initial irregular shaped, randomly distributed L1₂ and DO₂₂ phases are gradually transformed into cuboidal shape with round corner, regularly aligned along directions [100] and [001], and highly preferential selected microstructure is formed during the later stage of precipitation. The elastic field produced by the lattice mismatch between the coherent precipitates and the matrix has a strong influence on the coarsening kinetics, and there is no linear relationship between the cube of the average size of precipitates and the aging time, which does not agree with the results predicted by the classical Lifshitz-Slyozov-Wagner. The coarsening processes of L1₂ and DO₂₂ phases are retarded in elastically constrained system. In the concurrent system of L1₂ and DO₂₂ phases, there are two types of coarsening modes: the migration of antiphase domain boundaries and the interphase Ostwald ripening. Foundation item: Project(50671084) supported by the National Natural Science Foundation of China; Project(20070420218) supported by China Postdoctoral Science Foundation     

Delay-independent decentralized H ∞ control for multi-channel discrete-time systems with uncertainties

A robust decentralized H∞ control problem was considered for uncertain multi-channel discrete-time systems with time-delay. The uncertainties were assumed to be time-invariant, norm-bounded, and exist in the system, the time-delay and the output matrices. Dynamic output feedback was focused on. A sufficient condition for the multi-channel uncertain discrete time-delay system to be robustly stabilizable with a specified disturbance attenuation level was derived based on the theorem of Lyapunov stability theory. By setting the Lyapunov matrix as block diagonal appropriately according to the desired order of the controller, the problem was reduced to a linear matrix inequality （LMI） which is sufficient to existence condition but much more tractable. An example was given to show the efficiency of this method.     

Separation of baicalin from Scutellaria Baicalensis Georgi with polyamide

Separation of baicalin from Scutellaria Baicalensis Georgi with polyamide was studied. The adsorption isotherm, kinetic equation and desorption law were investigated by static and dynamic adsorption methods. The results show that the kinetic behavior is mainly controlled by the liquid film diffusion process and obeys the Boyd film diffusion equation. Equilibrium data for the adsorption of baicalin are correlated with Freundlich isotherm equation, i.e. q=3.8Ce2.057, suggesting that the relative capacity of polyamide to baicalin is somewhat small. The desorption results indicate that the baicalin with mass fraction of 33.86% and the least impurities can be obtained by chromatography using 60% ethanol as the eluant at room temperature.     

Sand-wear resistance of brush electroplated nanocomposite coating in oil and its application to remanufacturing

Sand-wear resistance of nano scale alumina particle reinforced nickel matrix composite coating (n-Al₂O₃/Ni) prepared by brush electroplating technique was investigated via wear tests in sand-contaminated oil lubricant, comparing with that of AISI1045 steel and brush electroplated Ni coating. Effects of testing load, sand content and sand size on worn volume of the three materials, and also coating surface roughness on worn volume of the brush electroplated coatings were accessed. Results show that the worn volume of all the three materials increases with increasing of testing load, sand content and sand size. In the same conditions, n-Al₂O₃/Ni composite coating has the smallest worn volume while AISI1045 steel has the largest because of the n-Al₂O₃ particle effects. As to n-Al₂O₃/Ni and Ni coatings, the surface-polished coatings have obviously lower worn volume than the as-plated coatings. The brush electroplated n-Al₂O₃/Ni composite coating was employed to remanufacture the sand-worn bearing seats of a heavy vehicle and good results were gained. Foundation item: Project (50235030) supported by the National Natural Science Foundation of China; Project (51489020104ZD0401) supported by the National Key Laboratory for Remanufacturing; Project(51418060105JB3058) supported by National Defence Foundation     

Antibiotic properties of Al2O3 doping silver

The preparation technique and properties of Ag-type inorganic antibiotic material carried by Al₂O₃ were studied. The results show that the material has good antibiotic and safety properties, the acute toxicity taken by stomata is LD ₅₀>8 000 mg/kg (little and big white rats), and the normal quantity in subacute toxicity test is 80 mg/(kg · d). The better mass fraction of doping Ag₂O in antibiotic material carried by Al₂O₃ is 4%–8%, and the optimal sintering temperature is from 1 000 °C to 1 100 °C. Foundation item: Project (2002AA327090) supported by National High Technology Research and Development Program of China     

Removal of lead in wastewater by immobilized inactivated cells of Rhizopus oligosporus

A novel technology for lead removal with nonliving Rhizopus oligosporus immobilized in calcium alginate was studied. The results show that the main influencing factors include pH value and interfering cations. pH value has different effects on biosorption of various heavy metals and lead adsorption can be proceeded by controlling pH value in a range of 2-5; interfering cations especially Cu( Ⅱ ) can make the adsorption amount of Pb( Ⅱ ) decrease by immobilized Rhizopus oligosporus. Desorption efficiency of different eluants and kinetics were investigated. Citrate the reaction equilibrium reaches 3 h. Immobilized biomass keeps high lead biosorption capacity after five cycles of regeneration.     

Coating of Fe, Ni on α-alumina microspheres by heterogeneous precipitation

1INTRODUCTION Themagneticmetal coatedceramicoxides,core shellstructuralcompositematerials,inwhichthinmetallicfilmsarecoatedonaceramicoxide matrixwithmicrometerparticlesizes,areattrac tiveduetothecombinationofthefunctionalchar acteristicsofmetalsandmechanicalpropertiesoftheceramicmatrix.Theceramic basedtransition metal coated,core shellcompositessuchasNi coatedAl2O3[1],Fe coatedAl2O3[2],FeNi coated Al2O3[3]orCoFe coatedSiO2[4],havebeenfoundtoexhibitinterestingfunctionalperformancesdue…     

Non-fragile delay-dependent H ∞ control of linear time-delay system with uncertainties in state and control input

The problem of designing a non-fragile delay-dependent H∞ state-feedback controller was investigated for a linear time-delay system with uncertainties in state and control input. First, a recently derived integral inequality method and Lyapunov-Krasovskii stability theory were used to derive new delay-dependent bounded real lemmas for a non-fragile state-feedback controller containing additive or multiplicative uncertainties. They ensure that the closed-loop system is internally stable and has a given H∞ disturbance attenuation level. Then, methods of designing a non-fragile H∞ state feedback controller were presented. No parameters need to be tuned and can be easily determined by solving linear matrix inequalities. Finally, the validity of the proposed methods was demonstrated by a numerical example with the asymptotically stable curves of system state and controller output under the initial condition of x（0）=[1 0 -1]^T and h=0.8 time-delay boundary.     

Retention of clay-solidified grouting curtain to Cd^2＋ , Pb^2＋ and Hg^2＋ in landfill of municipal solid waste

The effects of components and their ratio of groups on anti-seepage capability of clay-solidified grouting curtain and its permeability of heavy metal cations were investigated by permeating experiments, using reactive solute transport model to study the permeation of heavy metals (Cd²⁺, Pb²⁺ and Hg²⁺). The study of permeating for different mixture ratios of cement and clay indicates that hydraulic conductivity of clay-solidified groupting curtain with different ratios of solid to liquid or with the same ratio of solid to liquid but with different ratios of cement to clay is changed. The laboratory simulation test results also show that precipitates produced in heavy metal cation migration process in curtain block up water flowing passage which makes the hydraulic conductivity of the solution-permeated curtain decrease with the leakage time. The permeation velocities for different heavy metal cations vary with ionic concentration, exchange capacity and ion radius etc. The test results indicate that the permeation rapidity order of heavy metals cations in clay-solidified grouting curtain is Hg²⁺ > Pb²⁺ in the same experimental circumstance. In addition, permeability for different mixture ratios and antisepsis capabilities of clay-solidified grouting curtain were studied in tests. Foundation item: Project (2000-65) supported by the Fund for University Key Teacher by the Ministry of Education of China     

Isolation and characterization of YNTC-1, a novel Alicyclobacillus sendaiensis strain

A heterotrophic acidothermophilic bacterial strain, YNTC-1, was isolated from an acidic hot spring in Tengchong, Yunan, China. YNTC-1 grows at pH value of 1.5-8.0 and temperature of 40-70 ℃, with optimal pH and temperature at 3.0 and 55 ℃, respectively. The cells of the strain are in shape of short rod, with 1.0-1.2 μm in length and 0.7-0.8 μm in diameter, and with distinct spores at both poles of each cell. The predominant fatty acids in cellular membrane of the strain are C18：1 ω7c. 16s rRNA gene analysis reveals that this strain is closely related to Alicyclobacillus sendaiensis, with over 99% sequence similarity. Based on phenotypic and genotypic analyses, YNTC-1 is identified as a member ofA. sendaiensis. Considering some important morphological and biochemical differences between strain YNTC-1 and A. sendaiensis ATCC 27009T, YNTC-1 may be proposed to be a novel subspecies of A. sendaiensis. However, this viewpoint has to be confirmed by further studies. Co-bioleaching of pyrite and chalcopyrite with strain YN22, Sulfobacillus thermosulfidooxidans, shows that strain YNTC-1 has no evident influence on bioleaching rates of these two sulphide minerals.