Reduction of heat flux on divertor plates by remote radiative cooling in doublet III

Using a single null divertor configuration, heat flux intensity and its profile on the divertor plates as a function of plasma current and density were measured with an infrared camera and thermocouples. The vertical width of the heat flux on the divertor plates 2λ is ≈ 10 cm at the lower separatrix and is ≈ 5.5 cm at the upper separatrix. A diffusion coefficient D which is obtained from the measurement of the diffusion length across the scrape-off field lines is roughly proportional to and its magnitude is on the order of Bohm diffusion. The heat flux on the plates decreases by more than a factor of 5 with increasing electron density in the main plasma and is much smaller than that on the limiters in non-diverted plasmas. Only 3% of ohmic input power goes into the divertor plates at high density of the main plasma, while ≈ 20% goes in at low density. The decrease of heat flux is in good agreement with the increase of radiation loss in the divertor region. The heat flux on the divertor plates can be reduced by remote radiative cooling in high density discharges.     

Temperature Distribution and Heat Flux on the EAST Divertor Targets in H-Mode

An infrared camera (IR) has been put into operation in the Experimental Advanced Superconducting Tokamak (EAST), which is used to measure the temperature distribution on the surface of lower divertor target plates. With a finite di®erence method, the heat flux onto the divertor target plates is calculated from the surface temperature profile. The high confinement mode (H-mode) with type-III edge localized modes (ELMs) has been obtained with about 1 MW lower-hybrid wave power on the EAST in the autumn experiment in 2010. The analyzed H-mode discharges were lower single null X-point diverted discharges with a density range of < ne > (1~ 4)x 10¹⁹ m^-3. The surface temperature of the inner target plate increases with heating power. The peak temperature on the surface of target plates is lower than 200 oC with about 2.4 MW heating power. Comparison among the heat flux profiles occurring in di fferent phases in the same discharge has been erformed. It indicates that the heatflux profile obviously changes from the ohmic phase to the H-mode phase, and the full width at half maximum (FWHM) of the heat flux pro file is the narrowest during the ELM-free H-phase. On the outer target plate, the peak heat flux exceeds 2 MW/m2 during the ELMy H-mode phase, whereas it is only about 0.8 MW/m2 during the ELM-free phase in the same discharge.     

Design of snowflake-diverted equilibria of CFETR

The Chinese Fusion Engineering Test Reactor (CFETR) represents the next generation of full superconducting fusion reactors in China.Recently,CFETR was redesigned with a larger size and will be operated in two phases.To reduce the heat flux on the target plate,a snowflake (SF) divertor configuration is proposed.In this paper we show that by adding two dedicated poloidal field (PF) coils,the SF configuration can be achieved in both phases.The equilibria were calculated by TEQ code for a range of self-inductances li3.The coil currents were calculated at some fiducial points in the flattop phase.The results indicate that the PF coil system has the ability to maintain a long flattop phase in 7.5 and 10 MA inductive scenarios for the single null divertor (SND) and SF divertor configurations.The properties of the SF configuration were also analyzed.The connection length and flux expansion of the SF divertor were both increased significantly over the SND.     

Analysis of Divertor Heat Flux with Infrared Thermography During Gas Fuelling in the HL-2A Tokamak

In HL-2A tokamaks, the behavior of heat flux deposited on the divertor targets has been studied during deuterium gas fuelling. The heat flux is reduced significantly after supersonic molecular beam injection （SMBI） fuelling during Ohmic and electron cyclotron resonance heating （ECRH） divertor discharges. The SMBI fuelling causes an increase in the plasma density and this change results in the experienced change of the edge properties. Most of this reduction in divertor target heat flux occurs together with a high plasma radiation region located at near the X-point. The largest reduction in heat flux profiles is observed at the outboard divertor separatrix strike point, while the heat flux far from the strike point remains almost unchanged. In particular, with SMBI multi-pulses gas fuelling, a partially detached divertor regime is observed with a highly radiating region at the X-point. With the onset of the partially detached divertor regime, a sudden drop in both heat flux and power flow on the divertor target is observed. The reduction in power load on the divertor targets is roughly equal to the increase in plasma radiation loss.     

偏滤器物理设计与实验研究

应用B2-code模拟了偏滤器等离子体行为,优化了HL-2A装置偏滤器位形。研究了偏滤器刮削层中等离子体与器壁间过渡鞘层的离子碰撞效应,模拟研究了利用LHCD和NBI控制等离子体剖面分布在HL-2A中建立准稳态的反磁剪切位形。HL-2A装置首次实现了下单零点的偏滤器位形运行,完成了偏滤器初步物理实验,截至2004年底,获得等离子体电流320 kA,等离子体存在时间1 580 ms,环向磁场2.2 T。开展了高功率密度聚变堆偏滤器靶板的设计研究,特别是流动液态锂偏滤器靶板表面的物理过程的研究。探索性研究了用RF有质动力势改善偏滤器排灰效率和减少氚投料量。对FEB- E聚变堆偏滤器进行了优化设计。用电子束模拟对碳基材料及钨进行了高热负荷冲击实验,完成了钨/铜合金的热等静压焊接及热疲劳试验研究。研究了氦在钨中的滞留与热解吸行为。     

Double-null divertor configuration discharge and disruptive heat flux simulation using TSC on EAST

The tokamak simulation code (TSC) is employed to simulate the complete evolution of a disruptive discharge in the experimental advanced superconducting tokamak.The multiplication factor of the anomalous transport coefficient was adjusted to model the major disruptive discharge with double-null divertor configuration based on shot 61 916.The real-time feed-back control system for the plasma displacement was employed.Modeling results of the evolution of the poloidal field coil currents,the plasma current,the major radius,the plasma configuration all show agreement with experimental measurements.Results from the simulation show that during disruption,heat flux about 8 MW m-2 flows to the upper divertor target plate and about 6 MW m-2 flows to the lower divertor target plate.Computations predict that different amounts of heat fluxes on the divertor target plate could result by adjusting the multiplication factor of the anomalous transport coefficient.This shows that TSC has high flexibility and predictability.     

HL-2M Divertor Geometry Exploration with SOLPS5.0

One of the critical issues to be solved for HL-2M is the power and particle exhaust. Divertor target plate geometry strongly influences the plasma profiles by controlling the neutral recycling pattern, which has in turn a strong effect on the symmetry and stability of the divertor plasma and finally on the whole edge region. The numerical simulation software SOLPS5.0 Pack- age is used to design and explore the divertor target plates for HL-2M. We choose two divertor geometries, and assess the heat flux on the target plates and first wall, then further discuss the di- vertor plasma parameters, and how private flux baffling affects both neutral recirculation pattern and pumping efficiency.     

Super X divertors for solving heat and neutron flux problems of fusion devices

We present a new magnetic geometry, called the Super X divertor (SXD), that could potentially solve the enormous heat exhaust problem of next-generation high power-density experiments and fusion reactors. With only small changes in net coil currents, the axisymmetric SXD modification of the standard divertor (SD) coils greatly increases the divertor radius, the line length, and the plasma-wetted area. The lower B at large R decreases parallel heat flux and hence lowers the plasma temperature at SXD plates to below 10 eV, allowing higher divertor radiation fractions. The SXD could safely exhaust five times more heat than an SD, is unique in allowing adequate shielding of divertor target from neutron damage, and can enable much improved, reactor-relevant core plasma performance.     

Structural Modification and Thermal and Structural Analysis of the Divertor in HL-2A

The re-design of the adoptable structure and the cooling manner of the divertor in the HL-2A tokamak is based on the parameters confirmed by the optimum divertor configuration and the primary modification scheme. The characteristics of the new divertor system include the double shear joint design on the domes and the outer target plates as well as the poloidal flow with toroidal manifolds. The results of the thermal and structural analysis of the outer target plates show that the design of the poloidal flow with toroidal manifolds can improve the capability of the target plates to withstand the heat loads, and the double shear joint design is compatible with the stress intensity requirements by the electromagnetic loads due to halo currents.     

Magnetic configuration flexibility of snowflake divertor for HL-2M

HL-2M (Li, 2013 [1]) is a tokamak device that is under construction. Based on the magnetic coils design of HL-2M, four kinds of divertor configurations are calculated by CORSICA code (Pearlstein et al., 2001 [2]) with the same main plasma parameters, which are standard divertor, exact snowflake divertor, snowflake-plus divertor and snowflake-minus divertor configurations. The potential properties of these divertors are analyzed and presented in this paper: low poloidal field area around X-point, connection length from outside mid-plane to the primary X-point, target plate design and magnetic field shear. The results show that the snowflake configurations not only can reduce the heat load at divertor target plates, but also may improve the magneto-hydrodynamic stability by stronger magnetic shear at the edge. A new divertor configuration, named “tripod divertor”, is designed by adjusting the positions of the two X-points according to plasma parameters and magnetic coils current of HL-2M.     

Study of Striated Heat Flux on EAST Divertor Plates Induced by LHW Using Infrared Camera

An upgraded infrared （IR） imaging system which provides a wide field of view （FOV） has been installed on the Experimental Advanced Superconducting Tokamak （EAST） to monitor the surface temperatures on plasma facing components. Modified magnetic topology induced by lower hybrid wave （LHW） can lead to the formation of striated heat flux （SHF} on divertor plates which can be clearly observed by IR camera. In this paper, LHW power modulation is applied to analyze the appearance of SHF. It is also demonstrated that deuterium （D） pellet injection and supersonic molecular beam injection （SMBI） can to some extent reduce the heat flux on the outer strike point （OSP）, but enhance the SHF on lower outer plates （LOP） of divertor. This may provide an optional approach to actively control the distribution of heat flux on diveror plates, which can protect materials from long duration high-heat flux.     

The in-vessel components of the experiment WENDELSTEIN 7-X

The in-vessel components of the WENDELSTEIN 7-X stellarator consist of the divertor components and the wall protection with its internal cooling supply. The main components of the open divertor are the vertical and horizontal target plates which form the pumping gap, the cryo-vacuum pumps and the control coils. The divertor volume is closed by graphite shielded baffle modules and with divertor closures. All these components are designed to be actively water-cooled. For the first commissioning phase planned in 2014, an inertial-cooled test divertor will be installed instead of the actively water-cooled high heat flux divertor. The wall protection consists of graphite-protected heat shields in the higher loaded areas and stainless steel panels in the lower loaded regions. The wall protection cooling circuits are connected through 80 supply-ports via so-called “plug-ins”. It is envisaged to protect the diagnostic ports by panel-type port-liners. Special graphite-shielded port liners are used on the diagnostic injector and the neutral beam injector ports. The in-vessel components are mainly manufactured and tested at the Max-Planck-Institute für Plasmaphysik in its Garching workshop. Panels, high heat flux target elements and control coils are delivered by industrial partners. Manufacturing of the KiP (“Komponenten im Plasmagefäß”) is in plan. Delivery of the components will be in time.     

Estimates of EAST Operation Window with LHCD by Using a Core-SOL-Divertor Model

An experimental advanced superconducting tokamak (EAST) operation window with the lower hybrid current drive (LHCD) in H-mode is estimated by using a core-SOL-divertor (C-S-D) model validated by the present EAST divertor experiments. The operation window con- sists of four limits including two usual limits, one of which is the maximum allowable heat load onto the divertor plate, and two additional limits associated with the LHCD. The predictive EAST operation window is not qualified to fulfill its mission for high input power. To extend the opera- tion window, gas puffing and impurity seeding are presented as two effective methods. In addition, the effect of the LHCD current on the operation window is also discussed. Our numerical analysis results provide a reference for the safe operation of EAST experiments with LHCD in future.     

Simulation of Small Size Divertor Tokamak Plasma Edge Including Self-Consistent Electric Fields

The B2.SOLPES.0.5.2D code (Braams, Contrib Plasma Phys 36:276, 1996; Rozhansky and Tendler, Rev Plasma Phys 19:147, 1996) is applied for modeling SOL (Scrape off Layer) plasma in the small size divertor tokamak. Detailed distributions of the plasma heat flux and other plasma parameters in SOL, especially at the target plate of the divertor are found by modeling. The modeling results show that most of the electron heat flux and small part of ion heat flux arrive at target plate of the divertor, while, a large part of the ion heat flux and part of electron heat flux arrive at the outer wall. Also analysis of the role of poloidal E × B drifts in the redistribution of edge plasma is fulfilled.     

Calculation of the Heat Flux on the First Wall During Disruption on Tokamak

Disruptions are the most dangerous instabilities in tokamak plasma. During plasma disruption, the large amounts of energy will be deposited on Plasma Facing Components (PFCs) which is a damaging threat for the divertor target and the first wall materials. Therefore, studying the characteristic of heat deposition on the first wall is very significant. The Infrared (IR) camera is an effective tool to measure the surface temperature profile on the first wall on the Experimental Advanced Superconducting Tokamak (EAST). With a finite difference method, the heat flux arrived to the divertor can be calculated from the surface temperature. However, the surface layer on the divertor has a great influence on the calculation of the heat flux on the divertor. The numerical method for solving heat conduction for semi-infinite model is given in this paper. And the thermal resistance of surface layers is considered in this numerical method. In addition, the distribution of heat flux on the divertor during disruption is also shown.     

Feasibility study of an actively cooled tungsten divertor in Tore Supra for ITER technology testing

In order to reduce the risks for ITER Plasma Facing Components (PFCs), it is proposed to equip Tore Supra with a full tungsten divertor, benefitting from the unique long pulse capabilities, the high installed RF power and the long experience with actively cooled high heat flux components of the Tore Supra platform. The transformation from the current circular limiter geometry to the required X-point configuration will be achieved by installing a set of copper poloidal coils inside the vacuum vessel. The new configuration will allow for H-mode access, providing relevant plasma conditions for PFC technology validation. Furthermore, attractive steady-state regimes are expected to be achievable. The lower divertor target design will be closely based on that currently envisaged for ITER (W monoblocks), while the upper divertor region will be used to qualify the main first wall heat sink technology adopted for the ITER blanket modules (CuCrZr copper/stainless steel) with a tungsten coating (in place of the Be tiles which ITER will use). Extended plasma exposure will provide access to ITER critical issues such as PFC lifetime (melting, cracking, etc.), tokamak operation on damaged metallic surfaces, real time heat flux control through PFC monitoring, fuel retention and dust production.     

Manufacturing of the Wendelstein 7-X divertor and wall protection

The in-vessel components of Wendelstein 7-X (W7-X) with a total surface of 265 m² comprise the divertor and the wall protection. The high heat flux (HHF) and lower heat flux (LHF) target, the baffle, the end plates closing the divertor chamber, a cryo vacuum pump (CVP) and a control coil form one divertor unit. Steel panels and the graphite heat shield protect the wall, including the ports. The HHF target elements, the steel panels and the control coils are manufactured by industry. The remaining components will be manufactured by the Max-Planck-Institute für Plasmaphysik (IPP) at its Garching workshops. For all components the final acceptance tests will be performed by IPP. This paper summarizes the main aspects for manufacturing, the preceding development and qualification tests as well as the final acceptance tests for the in-vessel components.     

Conceptual design and heat transfer performance of a flat-tile water-cooled divertor target

The divertor target components for the Chinese fusion engineering test reactor (CFETR) and the future experimental advanced superconducting tokamak (EAST) need to remove a heat flux of up to ～20 MW m-2.In view of such a high heat flux removal requirement,this study proposes a conceptual design for a flat-tile divertor target based on explosive welding and brazing technology.Rectangular water-cooled channels with a special thermal transfer structure (TTS)are designed in the heat sink to improve the flat-tile divertor target's heat transfer performance(HTP).The parametric design and optimization methods are applied to study the influence of the TTS variation parameters,including height (H),width (W*),thickness (T),and spacing (L),on the HTP.The research results show that the flat-tile divertor target's HTP is sensitive to the TTS parameter changes,and the sensitivity is T ＞ L ＞ W* ＞ H.The HTP first increases and then decreases with the increase of T,L,and W* and gradually increases with the increase of H.The optimal design parameters are as follows:H =5.5 mm,W* =25.8 mm,T =2.2 mm,and L =9.7 mm.The HTP of the optimized flat-tile divertor target at different flow speeds and tungsten tile thicknesses is studied using the numerical simulation method.A flat-tile divertor mock-up is developed according to the optimized parameters.In addition,high heat flux (HHF)tests are performed on an electron beam facility to further investigate the mock-up HTP.The numerical simulation calculation results show that the optimized flat-tile divertor target has great potential for handling the steady-state heat load of 20 MW m-2 under the tungsten tile thickness＜5 mm and the flow speed ≥7 m s-1.The heat transfer efficiency of the flat-tile divertor target with rectangular cooling channels improves by ～ 13％ and ～30％ compared to that of the flat-tile divertor target with circular cooling channels and the ITER-like monoblock,respectively.The HHF tests indicate that the flat-tile divertor mock-up can successfully withstand 1000 cycles of 20 MW m-2 of heat load without visible deformation,damage,and HTP degradation.The surface temperature of the flat-tile divertor mock-up at the 1000th cycle is only ～930 ℃.The fiat-tile divertor target's HTP is greatly improved by the parametric design and optimization method,and is better than the ITER-like monoblock and the fiat-tile mock-up for the WEST divertor.This conceptual design is currently being applied to the engineering design of the CFETR and EAST flat-tile divertors.     

Modeling of Heat Fluxes in Edge Plasma of Small Size Divertor Tokamak

The heat flows out from the tokamak core region are collected on the divertor plates and external wall. Control of heat flux exhaust in the SOL and divertor plates regions is one of the important issues in tokamak physics. There are important phenomena affecting heat flows were simulated. The simulation is based on the B2SOLPS5.0 2D multifluid code. It is demonstrated that, the following results: (1) The simulation shows that, the operation of small size divertor tokamak, the divertor plate with/without impurities influence on profiles of electron, ion temperatures, and heat loads significantly. (2) Under normal direction of parallel (toroidal) magnetic field and different values of edge plasma density, strong “SOL” heat flow exists directed towards the LFS (outer) plate. (3) The simulation results show that, the increasing of the plasma density strong influence on the ion and electron poloidal heat fluxes profile significantly. The ion and electron polodial heat flux increase by factor “~8” and “2.4” times. (4) The simulation results show that the in–out asymmetry of heat fluxes was reversed when switching on/off E × B drifts in the edge plasma of this tokamak. (5) The simulation results show correlation between the in–out asymmetry divertor heat fluxes and E × B drift velocity. (6) The observed heat loads asymmetry between HFS and LFS plates can be explained with the radial electric field in SOL. (7) Also the simulation results performed result in, the in–out asymmetry strong influence on the characteristic length of ion poloidal heat flux.