Fabrication of nano-sized Al2O3 reinforced casting aluminum composite focusing on preparation process of reinforcement powders and evaluation of its properties

In this study, a novel approach was used to fabricate Al₂O₃ nanoparticle reinforced aluminum composites to avoid agglomeration of nanoparticles in matrix. Al₂O₃ nanoparticles were separately milled with aluminum and copper powders at different milling durations and incorporated into A356 alloy via stir casting method. The effects of milling process and milling time on mechanical properties of the composites were evaluated by hardness, tensile, and compression tests. Based on the results, some of the composites, reinforced with Al₂O₃-metallic mixed powders, showed higher mechanical performance compared with that of the pure Al₂O₃ nanoparticle reinforced composite. This enhancement is related to uniform distribution of individual nanoparticles and grain refinement of A356 matrix, shown in microstructural studies. Moreover, the results showed that an increase in milling time, led to a gradual decrease in mechanical performance of the samples. It can be related to further oxidation of metallic powders that can act as inclusions and also further probable contamination of nanoparticles with increase in milling time. Studies on the fracture surfaces revealed that the failure of matrix was the basic mechanism of fracture in the composites. Agglomerated nanoparticles were observed on dendrites in the fracture surface of the Al₂O₃–Al reinforcement samples.     

Determining the effect of flake matrix size and Al2O3 content on microstructure and mechanical properties of Al2O3 nanoparticle reinforced Al matrix composites

In this study, Al2024 matrix composites reinforced with Al₂O₃ nanoparticle contents ranging from 1 to 5?wt% were produced via a new method called as flake powder metallurgy (FPM). The effect of flake size and Al₂O₃ nanoparticle content on the reinforcement distribution, microstructure, physical, and mechanical properties of the composites were studied. SEM analysis was performed to investigate the microstructure of metal matrix and the distribution of nanoparticles. The hot-pressed density increased with decreasing the matrix size. The hardness of the Al2024–Al₂O₃ nanocomposites fabricated by using fine matrix powders increased as compared to the Al2024–Al₂O₃ nanocomposites produced by using coarse matrix powders. It has been found that the FPM method proposed in this study revealed to be an effective method for the production of nanoparticle reinforced metal matrix composites.     

Microstructure and mechanical properties of cast (Al–Si)/SiCp composites produced by liquid and semisolid double stirring process

Abstract

A stirring process containing two steps, i.e. liquid and then semisolid stirring, was used to produce SiC particle reinforced aluminium matrix composites. The major advantages of this process are that full wetting of SiC particles by molten aluminium can be readily achieved at relatively low stirring rates, and undesirable Al₄ C₃ is not formed at the Al/SiC interface due to lower processing temperatures. Cast Al–Si matrix composites reinforced with 15 and 20 vol.-%SiC particles were produced in the present work. The mechanical properties of the composites were evaluated under the conditions of investment mould casting and heat treatment. For the composites obtained without employing semisolid stirring, the aggregation of SiC particles observed in the microstructure of composites resulted in quite poor mechanical properties. Observations and analyses indicated that some Al/SiC interfaces were very clean, and a reaction product of spinel MgAl₂O₄ was also found at some Al/SiC interfaces. Silicon dioxide (SiO₂ ) was found to exist on the surface of as purchased and 250°C dried SiC powders. This SiO₂ is involved in the spinel reaction at the interface between the SiC particles and the matrix in the present Al/SiC composites.     

Micro-yield property of sub-micron Al2O3 particle reinforced 2024 aluminum matrix composite

The microstructure and micro-yield strength of sub-micron Al₂O₃ particle reinforced 2024Al composites and the effect of the thermal-cold cycling treatment on the microstructure and properties were studied. The results show that the dislocations are rare in the microstructure of the sub-micron Al₂O_3p/2024Al composite in the squeeze casting condition. Aging and thermal-cold cycling treatment does not change this phenomenon. The Al₂O₃ particles are fine, so the thermal misfit between particles and the matrix is very small during the temperature change, resulting in decreased dislocations. The tiny and uniformly dispersed S′ precipitates and sub-micron particles can effectively pin dislocations, therefore, the micro-yield strength of the composite increases. Depending on the condition of the thermal-cold cycling treatment after aging, both the size and distribution of the S′ precipitates in the composite change, and they have great effect on the micro-yield strength of the composite.     

纳米Al2O3改性玻璃纤维增强复合材料低温力学性能研究

简述了纳米Al2O3改性玻璃纤维增强环氧树脂基复合材料的制备,并对其常温、低温力学性能进行实验。结果表明,常温、低温下,复合材料的力学性能随着纳米Al2O3含量的增加都呈现先增强后减弱的趋势。低温处理使复合材料的力学性能得到提升,并且低温下Al2O3的引入对复合材料强度的改善效果比常温下明显,Al2O3含量为1%(质量分数)时,拉伸强度提高比例高达16.61%。其原因是低温下基体强度增大,另外基体热膨胀系数大,收缩明显,界面粘接强度增大,纳米Al2O3颗粒在界面处与树脂基体结合更深入,从而使纳米粒子阻碍微裂纹扩展的能力更强。     

Fabrication of aluminum matrix composites with enhanced mechanical properties reinforced by in situ generated MgAl2O4 whiskers

Aluminum matrix composite reinforced by in situ generated single crystalline MgAl₂O₄ whiskers was fabricated by chemical synthesis method in an Al-Mg-H₃BO₃ system. A large number of MgAl₂O₄ whiskers were generated during the sintering process and distributed homogeneously in the Al matrix. The whiskers penetrate into the matrix grains to form the framework of the materials, leading to an incredible increase in mechanical properties of the composites. The generation mechanism of the MgAl₂O₄ whiskers was also discussed.     

Fabrication of AA6061/Al2O3p composites from elemental and alloy powders

The tensile properties and microstructures of AA6061/Al₂O_3p composites fabricated by the pressureless infiltration method under a nitrogen atmosphere were examined. Since the spontaneous infiltration of molten metal into elemental powders bed as well as alloy powders bed occurred at 700°C for 1 hour under a nitrogen atmosphere, it was possible to fabricate 6061 Al matrix composite reinforced with Al₂O_3p irrespective of the type of metal powders. Both MgAl₂O₄ and MgO were formed at interfaces between Al₂O₃ and the matrix. In addition, MgAl₂O₄ was formed at within the matrix by in situ reaction during composite fabrication. Fine AlN was formed by in situ reaction in both composites. A significant strengthening in the composites occurred due to the formation ofin situ AlN particle and addition of Al₂O₃ particles, as compared to the commercial alloy, while tensile properties in the both elemental and alloy powders composites showed similar trend.     

Structure and properties of modified compocast microsilica reinforced aluminum matrix composite

A356 aluminum alloy reinforced with 7 wt.% microsilica composites was produced by the three different processing routes viz. liquid metal stir casting followed by gravity casting, compocasting followed by squeeze casting and modified compocasting route and their properties were examined. Microstructure of liquid metal stir cast Al MMC shows agglomeration of particles leading to high porosity level in the developed material. Adopting new route of compocasting followed by squeeze casting process prevents the agglomeration sites with uniform distribution and dispersion of the dispersoids in the matrix metal. Modified compocasting process reduces the segregation of particles in the final composites thus enhancing the mechanical, tribological and corrosion properties of the composites. Superior wear-resistance properties were exhibited by the modified compocast composite compared to the unreinforced squeeze cast alloy and abrasive type wear mechanism was observed in the case of composite. Increasing the sliding speed resulted in the quick evolution of tribolayer and the wear rate of composite gets reduced. The presence of intermetallic phases like MgAl₂O₄, NaAlSi₃O₈ and KAlSi₃O₈ has a favorable effect on increased corrosion resistance of the composite. Microsilica particles significantly enhanced the compressive strength of modified compocast composites compared to the unreinforced squeeze cast Al alloy.     

纳米Al2O3增强铝基复合材料的制备技术和发展方向

纳米颗粒具有极高的增强效率,能够显著提高铝基复合材料的综合性能.纳米Al2 O3/Al复合材料作为其中的代表,具有高弹性模量、高强度和低密度等优势,得到长期的关注和研究.详细介绍了纳米Al2O3/Al复合材料的制备方法,分析了各制备方法的优点和缺点,并对纳米Al2O3/Al复合材料的发展前景进行了展望.     

Fabrication and microstructure of in situ toughened Al2O3/Fe3Al

Fe₃Al nano-particles and commercial purity Al₂O₃ powders were used as raw materials to fabricate in situ reinforced Al₂O₃/Fe₃Al nano/micro-composites. Densification and microstructure were studied. The Al₂O₃ matrix grains were characterized by platelet grains. The Fe₃Al particles inhibited the grain growth of Al₂O₃ grains and limited the densification of the composites. In Al₂O₃/Fe₃Al composites, the Fe₃Al particles were uniformly dispersed in the Al₂O₃ matrix. The major Fe₃Al micro-particles, about 1 μm in average size, existed at Al₂O₃ grain boundaries, and the Fe₃Al nano-particles were found embedded in the matrix grains. The grain size of the intragranular particles ranged from several to several hundred nanometers. The grain size and aspect ratio of Al₂O₃ platelet grains and distribution of intragranular Fe₃Al could be optimized by controlling the Fe₃Al contents and sintering process. The in situ formed Al₂O₃ platelet grains, as well as Fe₃Al dispersoids, were beneficial to the increase of the mechanical properties of alumina.     

Fabrication and properties of in situ synthesized particles reinforced aluminum matrix composites of Al–Zr–O–B system

A new in situ Al–Zr–O–B system is exploited. The Al–Zr(CO₃)₂–KBF₄ components are used to fabricate the particle reinforced aluminum matrix composites by the direct melt reaction method. The analytical results of XRD and SEM show that the in situ endogenetic particles are ZrAl₃, ZrB₂ and Al₂O₃, which are well distributed in the aluminum matrix. The sizes of reinforced particles are 0.5–2.5 μm. The results of mechanical properties of the composites show that the tensile strength and yield strength are improved with the increase of theoretical volume fraction of particles in matrix in the range of 0–12%, which are much superior to those of aluminum matrix. The best elongation of composites is 33% when the theoretical volume fraction is 3%. The fracture mechanism belongs to a ductile one. The wear resistance properties of the composites are much higher than that of aluminum matrix. The best abradability is got when the theoretical volume fraction of particles is 6%. The wear mechanism of the aluminum matrix is adhesive wear while the wear mechanism of (ZrAl₃ + ZrB₂ + Al₂O₃)_p/Al composites is abrasive wear.     

Effect of ceramic reinforcements on microwave sintered metal matrix composites

Metal matrix composites (MMCs) using Aluminum Alloy 2900 and 2024 as matrix material with silicon carbide and alumina as reinforcement have been fabricated through powder metallurgy route for investigation. The average particle size of matrix metal and reinforcement material considered in this research is 10?µm. AA-SiC and AA-Al₂O₃ composites with 3, 6, and 9 weight percentage (wt%) of SiC and Al₂O₃ are fabricated. The Rockwell hardness and Compressive strength of AA-SiC and AA-Al₂O₃ composites were found to increase with an increase in the wt% of reinforcement when the samples were microwave sintered. AA 2024 with 6?wt% Al₂O₃ reinforced MMCs samples were exhibiting improved hardness results, strength behavior, and stress-strain behavior when the samples are microwave sintered. AA 2900 with 6?wt% Al₂O₃ exhibited good ductility and formability properties. Good Microstructural bonding was observed in the MMCs, which is attributed to finer Al₂O₃ particulate used as reinforcement and the microwave sintering.     

Role of controlled debonding along fiber/matrix interfaces in the strength and toughness of metal matrix composites

In metal matrix composites toughness is derived primarily from the plastic work of rupture of ductile matrix ligaments between the fractured fibers and from the plastic work of simple shear separation along steps connecting major fracture terraces. In the optimization of tensile strength in the longitudinal and transverse directions together with the respective works of fracture the most important factor is the control of the extent of debonding along interfaces between the fibers and the matrix, which develops locally in the course of deformation in a continuously changing mix of modes. In Al alloy matrix composites reinforced with Al₂O₃ fibers an effective means of controlling the key interface fracture toughness is through coarsening of Al₂Cu intermetallic interface precipitates which prescribe a ductile fracture separation layer. A combined experimental approach and micromechanical modeling, utilizing a specially tailored novel tension/shear: traction/separation law provides the means for further optimization of overall behavior. This revised version was published online in July 2006 with corrections to the Cover Date.     

Microstructure investigations and mechanical properties of an Al‐Al2O3 MMC produced by semi‐solid solidification

The influence of the semi‐solid solidification production parameters (shear rate and agitation time) and the concentration of reinforcing particles on the microstructure formation and mechanical properties of a 520 aluminum alloy reinforced with Al₂O₃ particles was investigated. Depending on the content of reinforcing particles and the stirring conditions different rosette structures were formed. The type of wear mechanism (delamination or adhesion) depends on the size of the rosettes and the distribution of Al₂O₃ reinforcements. Best mechanical properties were obtained for metal matrix composites reinforced with 12 wt% of Al₂O₃ stirred at a shear rate of 2100 s^–1 for 1800 s. These samples showed tensile strength and yield stress similar to the commercial A520 alloy. The hardness and wear resistance were improved by the addition of Al₂O₃ particles, meanwhile the elongation to fracture was reduced.     

Microstructure and properties of in situ generated MgAl2O4 spinel whisker reinforced aluminum matrix composites

In this study, a novel MgAl₂O₄ spinel whisker reinforced composite was synthesized in situ in an Al matrix by a powder metallurgy technique. In MgAl₂O₄/Al composite, the whisker content was varied from 3% to 15% in weight and each one was completely investigated. The as-produced MgAl₂O₄/Al composites were hot extruded and MgAl₂O₄/Al composites rods with high relative density were obtained. Both the hardness and the softening temperature of the composites increased with increasing content of MgAl₂O₄ whisker. The dilatometric measurements show that MgAl₂O₄ whisker reinforced Al composites exhibit better thermal stability and lower thermal expansion coefficient than aluminum alloys. Moreover, wear resistance is also enhanced due to the formation of the whisker-formed network structure which is capable of bearing and transferring abrasion effect. Thus, the enhanced properties of the composites could be obtained.     

Infiltrated Cu8Al–Ti alumina composites

The effect of titanium additions on the interface and mechanical properties of infiltrated Cu8 wt%Al–Al₂O₃ composites containing 57 ± 2 vol% ceramic are investigated, exploring two different Al₂O₃ particle types and four different Ti concentrations (0, 0.2, 1, 2 wt%Ti). Addition of 0.2 wt%Ti leads to the development of a thin (5–10 nm) layer enriched in Ti at the interface between Cu alloy and Al₂O₃ particles; this Ti concentration produces the best mechanical properties. With higher Ti-contents Ti₃(Cu, Al)₃O appears; this decreases both the interface and composite strength. Composites reinforced with vapor-grown polygonal alumina particles show superior mechanical properties compared to those reinforced by angular comminuted alumina particles, as has been previously documented for aluminum-based matrices. Micromechanical analysis shows that damage accumulation is more extensive, as is matrix hardening by dislocation emission during composite cooldown, in the present Cu8 wt%Al matrix composites compared with similarly reinforced and processed Al-matrix composites.     

Influence of matrix alloying elements on reactive synthesis of 2124 aluminium alloy metal matrix composites

Abstract

In situ TiB₂ particle reinforced Al alloys are produced by reactive synthesis from elemental and prealloyed powders. The influence of 2124 alloying elements on the reactive synthesis is evaluated with a comparison of elemental AI, elemental AI-Cu mixture, and 2124 Al prealloyed powders as matrix materials. Experimental investigations by differential scanning calorimetry and dilatometry showed that the presence of Cu leads to an increase in the reaction rate during the formation of intermediate reaction products in comparison with the elemental Al matrix. X-ray diffraction of the reaction products showed a more complete conversion of the intermediate Al₃ Ti as a result of Cu addition. The Cu has no influence on the TiB₂ particle size, but the TiB₂ morphology changed from pure hexagonal to a more rounded morphology.     

Microstructural evolution of reinforcements in the remelting in situ TiC/Al-12Si composites treated by ultrasonic vibration

Clusters of reinforced particles and long rod-like Al₃Ti particles are usually present in the matrix of in situ TiC/Al alloy composites fabricated via SHS reaction of the Al-Ti-C system in the molten aluminum alloys. In order to improve the properties of the composites, the above issues should be solved effectively. In our research, high-intensity ultrasonic vibration was introduced into the remelting TiC/Al-12Si composites containing clusters of TiC particles and long rod-like Al₃Ti phase to optimize the microstructure of the composites. The results of SEM showed that long rod-like Al₃Ti particles were turned into small blocky ones and large clusters were broken up into small ones. In the meantime, individual TiC particles could be peeled off from the clusters and distributed uniformly in the matrix. An in situ TiC/Al-12Si composite with a homogeneous microstructure was attained successfully. The evolution of the morphology of Al₃Ti phase and the clusters in the ultrasonic field was also discussed.     

Alumina powder assisted carbon nanotubes reinforced Mg matrix composites

Mg matrix composites reinforced by carbon nanotubes (CNTs)-Al₂O₃ mixture, which was synthesized by in situ growing CNTs over Al₂O₃ particles through chemical vapor deposition (CVD) using Ni catalyst, were fabricated by means of powder metallurgy process, followed by hot-extrusion. By controlling synthesis conditions, the as-grown CNTs over Al₂O₃ particles possessed high degree of graphitization, ideal morphology, higher purity and homogeneous dispersion. Due to the ‘vehicle’ carrying effect of micrometer-level A₂O₃, CNTs were easy to be homogeneously dispersed in Mg matrix under moderate ball milling. Meanwhile, Al₂O₃ particles as catalyst carriers, together with CNTs, play the roles of synergistic reinforcements in Mg matrix. Consequently, the Mg matrix composites reinforced by CNTs-Al₂O₃ mixture exhibited remarkable mechanical properties.     

Effects of ball milling and high-pressure torsion for improving mechanical properties of Al–Al2O3 nanocomposites

Pure Al powders were mixed with a 30 % volume fraction of Al₂O₃ powders having particle sizes of ~30 nm. The mixed powders were first subjected to ball milling (BM) and thereafter consolidated by high-pressure torsion (HPT) at room temperature under a pressure of 3 GPa for 10 turns. The Al–Al₂O₃ composite produced by BM and HPT (BM + HPT) had a more uniform dispersion of the nano-sized Al₂O₃ particles in the Al matrix. Hardness values of the BM + HPT composites were higher than those of the composites without BM. It is shown that the use of BM powders for HPT is more effective in achieving a uniform dispersion of the nano-sized Al₂O₃ particles and in improving mechanical properties of the Al–Al₂O₃ nanocomposites.