Synthesis and characterizations of modified expanded graphite/emulsion styrene butadiene rubber nanocomposites: Mechanical,dynamic mechanical and morphological properties

The present research work demonstrated the reinforcing effect of expanded graphite (EG) and modified EG (MEG) with and without carbon black (CB) on the physical, mechanical and thermo-mechanical properties of emulsion polymerized styrene butadiene rubber (SBR) vulcanizates. In separate batches, EG and MEG flakes with and without CB were incorporated into the SBR by melt blending. The microstructures of the nanocomposites were precisely characterized by wide angle X-ray diffraction (WAXD) analysis and high resolution transmission electron microscope (HR-TEM). EG and MEG filled SBR compounds showed improvement in the curing features, mechanical, thermal and dynamic mechanical properties than their respective controls.     

Monitoring and simulations of hydrolysis in epoxy matrix composites during hygrothermal aging

In this paper, we studied the water transport in thermoset matrices. We used Fourier Transform Infrared analysis (FTIR) during sorption/desorption experiments to investigate the interaction between sorbed water and the epoxy network. Our results demonstrated that the polymer matrix undergoes hydrolysis. We found that the chemical species involved in the reaction process was the residual anhydride groups. These results support the physical basis of the three-dimensional (3D) diffusion/reaction model. We finally showed that this model is able to reproduce multi-cycle sorption/desorption experiment, as well as water uptake in hybrid metal/epoxy samples. We simulated the 3D distributions of the diffusing water and the reacted water.     

Effects of stretching on mechanical properties of aligned multi-walled carbon nanotube/epoxy composites

Composites based on epoxy resin and differently aligned multi-walled carbon nanotube (MWCNT) sheets have been developed using hot-melt prepreg processing. Aligned MWCNT sheets were produced from MWCNT arrays using the drawing and winding technique. Wavy MWCNTs in the sheets have limited reinforcement efficiency in the composites. Therefore, mechanical stretching of the MWCNT sheets and their prepregs was conducted for this study. Mechanical stretching of the MWCNT sheets and hot stretching of the MWCNT/epoxy prepregs markedly improved the mechanical properties of the composites. The improved mechanical properties of stretched composites derived from the increased MWCNT volume fraction and the reduced MWCNT waviness caused by stretching. With a 3% stretch ratio, the MWCNT/epoxy composites achieved their best mechanical properties in this study. Although hot stretching of the prepregs increased the tensile strength and modulus of the composites considerably, its efficiency was lower than that of stretching the MWCNT sheets.     

Effect of surface treatment on thermal stability of the hemp-PLA composites: Correlation of activation energy with thermal degradation

The thermal behavior of hemp-poly lactic acid composites with both untreated and chemically surface modified hemp fiber was characterized by means of activation energy of thermal degradation. Three chemical surface modification employed were; alkali, silane and acetic anhydride. Model-free isoconversion Flynn–Wall–Ozawa method was chosen to evaluate the activation energy of composites. The results indicated that composites prepared with acetic anhydride modified hemp had 10–13% higher activation energy compared to other composites. Further, among the three surface modifications, acetic anhydride resulted in higher activation energy (159–163 kJ/mol). Fourier transform infrared spectroscopy supported the findings of thermogravimetric analysis results, wherein surface functionalization changes were observed as a result of surface modification of hemp fiber. It was concluded that, higher bond energy results in higher activation energy, which improves thermal stability. The activation energy data can aid in better understanding of the thermal degradation behavior of composites as a function of composite processing.     

Investigation of thermal conductivity and dielectric properties of LDPE-matrix composites filled with hybrid filler of hollow glass microspheres and nitride particles

The hybrid filler of hollow glass microspheres (HGM) and nitride particles was filled into low-density polyethylene (LDPE) matrix via powder mixing and then hot pressing technology to obtain the composites with higher thermal conductivity as well as lower dielectric constant (D_k) and loss (D_f). The effects of surface modification of nitride particles and HGMs as well as volume ratio between them on the thermal conductivity and dielectric properties at 1 MHz of the composites were first investigated. The results indicate that the surface modification of the filler has a beneficial effect on thermal conductivity and dielectric properties of the composites due to the good interfacial adhesion between the filler and matrix. An optimal volume ratio of nitride particles to HGMs of 1:1 is determined on the basis of overall performance of the composites. The thermal conductivity as well as dielectric properties at 1 MHz and microwave frequency of the composites made from surface-modified fillers with the optimal nitride to HGM volume ratio were investigated as a function of the total volume fraction of hybrid filler. It is found that the thermal conductivity increases with filler volume fraction, and it is mainly related to the type of nitride particle other than HGM. The D_k values at 1 MHz and microwave frequency show an increasing trend with filler volume fraction and depend largely on the types of both nitride particles and HGMs. The D_f values at 1 MHz or quality factor (Q × f) at microwave frequency show an increasing or decreasing trend with filler volume fraction and also depend on the types of both nitride particle and HGM. Finally, optimal type of HGM and nitride particles as well as corresponding thermal conductivity and dielectric properties is obtained. SEM observations show that the hybrid filler particles are agglomerated around the LDPE matrix particles, and within the agglomerates the smaller-sized nitride particles in the hybrid filler can easily form thermally conductive networks to make the composites with high thermal conductivity. At the same time, the increase of the value D_k of the composites is restricted due to the presence of HGMs.     

Influence of morphology on the dynamic mechanical characteristics of PP-EP/EVA/organoclay nanocomposites

A study on the dynamic mechanical properties of polypropylene copolymer/ethylene–vinyl acetate/organoclay (PP-EP/EVA/C20A) nanocomposites is presented. Nanocomposites were obtained by melt blending. Morphology consisting of intercalated–exfoliated clay nanolayers preferentially located within the EVA phase was observed by transmission electron microscopy (TEM) and wide angle X-ray diffraction (WAXD). Polar groups of vinyl acetate in the EVA facilitated the polymer–clay interactions. Changes in the glass transition temperature (T_g) were correlated with changes in the clay intercalation–exfoliation levels. The highly reinforced with intercalated–exfoliated clay layers EVA phase was considered as the origin of the improvement on mechanical properties of the ternary nanocomposites and is associated with the increase on viscosity, heat deflection temperature (HDT), and storage modulus.     

The voids formation mechanisms and their effects on the mechanical properties of flax fiber reinforced epoxy composites

Unidirectional flax fiber reinforced composites (FFRC) were made by hot press. Effects of processing parameters, including curing pressure, time and temperature on the distribution, shape and content of the voids formed during the manufacturing process of FFRC were investigated. The voids were characterized with the aid of ultrasonic C-scan and optical microscopy. Tensile and interlaminar shear properties of FFRC containing different content and shape of the voids were tested. The results showed that the voids were easily trapped in both the intralaminar and inside the flax yarns of FFRC due to the distinct structural characteristics of flax fibers. The relationships between voids and mechanical properties of the composites were established.     

Tailoring of thermal and dielectric properties of LDPE-matrix composites by the volume fraction,density, and surface modification of hollow glass microsphere filler

Hollow glass microsphere (HGM) filled low-density polyethylene (LDPE) composites were prepared, and the effects of density, content, and surface modification of HGM on the thermal and dielectric properties of the composites were investigated. It is found that the thermal conductivity of the composites decreases with increasing HGM content or decreasing HGM density. At the same HGM content and density, the composites filled with suitable amount of silane coupling agent (KH570) modified HGM exhibit higher thermal conductivity than unmodified-HGM filled composites. The dielectric constant at 1 MHz of the composites also decreases with increasing HGM content or decreasing HGM density, but their dielectric loss increases with increasing HGM content or increasing HGM density. By modifying the surface of HGM with suitable amount of KH570, the dielectric constant and loss at 1 MHz of the composites can be decreased at the same time. The results of microwave dielectric properties of the composites indicate that the dielectric constant decreases with increasing HGM content or decreasing HGM density, the quality factor (Q × f) decreases with increasing HGM content or increasing HGM density, but both dielectric constant and quality factor are slightly affected by the surface modification of HGM. Due to lower intrinsic thermal conductivity and dielectric constant but higher dielectric loss of HGM than LDPE, the thermal conductivity and dielectric properties of the composites can be controlled with adding HGM and varying its volume fraction. The surface modification of HGM improves the interface contact between HGM and LDPE in the composites, which is confirmed by the SEM observation, and thus the heat conduction and dielectric properties at low frequency are improved. Based on calculated thermal conductivity and dielectric constant of HGM, the experimental trends of thermal conductivity and dielectric constant at 1 MHz of the composites are analyzed by using different models, including typical models for particles-filled composites and special models developed for hollow microsphere filled composites. The results from suitable models show close correlation with the experimental values.     

Characterization of organo-montmorillonite (OMMT) modified wood flour and properties of its composites with poly(lactic acid)

In this research, sodium-montmorillonite (Na-MMT) at four different concentrations (0.5%, 1.0%, 2.0% and 4.0%) and didecyl dimethyl ammonium chloride (DDAC) were used to modify wood flour (WF) in a two-step process to form organo-montmorillonite (OMMT) inside the WF. Then the WFs with three sizes were mixed with poly(lactic acid) (PLA) to produce WF/PLA composites. The treated WF was characterized and some physical and mechanical properties of the composites were tested. The results showed that: (1) Na-MMT was successfully transformed to OMMT and uniformly distributed inside WF; (2) at 0.5% MMT concentration, water repellency, flexural and tensile properties of the composites were improved significantly. However, after introducing more OMMT, the enhancements diminished because of poor interfacial adhesion caused by OMMT agglomeration; (3) the composites with the maximum size of WF showed the most significant improvements among all, suggesting bigger WF was more suitable for this modification process.     

Study on thermal properties of graphene foam/graphene sheets filled polymer composites

The polymer composites composed of graphene foam (GF), graphene sheets (GSs) and pliable polydimethylsiloxane (PDMS) were fabricated and their thermal properties were investigated. Due to the unique interconnected structure of GF, the thermal conductivity of GF/PDMS composite reaches 0.56 W m⁻¹ K⁻¹, which is about 300% that of pure PDMS, and 20% higher than that of GS/PDMS composite with the same graphene loading of 0.7 wt%. Its coefficient of thermal expansion is (80–137) × 10⁻⁶/K within 25–150 °C, much lower than those of GS/PDMS composite and pure PDMS. In addition, it also shows superior thermal and dimensional stability. All above results demonstrate that the GF/PDMS composite is a good candidate for thermal interface materials, which could be applied in the thermal management of electronic devices, etc.     

Preparation and tribological performance of chemically-modified reduced graphene oxide/polyacrylonitrile composites

Interface control and dispersion of graphene base nanomaterials in polymer matrix are challenging to develop high comprehensive nanocomposites due to their strong interlayer cohesive energy and chemical inertia. In this research, an efficient approach is presented to functionalize reduced graphene oxide nanosheets by N-[3-(trimethoxylsilyl)propyl]ethylenediamine, which is dispersed into polyacrylonitrile to prepare N-[3-(trimethoxylsilyl)propyl]ethylenediamine – reduced graphene oxide/polyacrylonitrile nanocomposites. A thermogravimetric analysis technique was employed to evaluate thermal properties of the nanocomposites. The tribological properties of the polyacrylonitrile/graphene nanocomposites were investigated. The morphologies and volume of the worn surface were examined using a 3D profilometer. The impact of loading ratio on friction coefficient, carry-bearing capacity and durability were studied. The N-[3-(trimethoxylsilyl)propyl]ethylenediamine – reduced graphene oxide/polyacrylonitrile nanocomposite with appropriate loading ratio of reduced graphene oxide exhibited a high load-bearing capacity and durability. Therefore, the polyacrylonitrile/graphene nanocomposite shows promising potential to industrial applications involving the lubrication and anti-wear.     

Enhanced stress transfer and thermal properties of polyimide composites with covalent functionalized reduced graphene oxide

This work prepares (3-aminopropyl) trimethoxysilane (APTMS)-functionalized reduced graphene oxide (APTMS-rGO)/polyimide (PI) composite (APTMS-rGO/PI) through in-situ polymerization. NH₂-functionalized rGO coupled by APTMS demonstrates the good reinforced efficiency in mechanical and thermal properties, which is ascribed to the covalent-functionalized PI matrix by APTMS-rGO sheets. The uniform dispersion of APTMS-rGO increases the glass transition temperature (Tg) and the thermal decomposition temperature (Td), exhibiting 21.7 °C and 44 °C improvements, respectively. The tensile strength of the composites with 0.3 wt% APTMS-rGO is 31% higher than that of neat PI, and Young’s modulus is 35% higher than that of neat PI. Raman spectroscopy show the obvious G band shift, and also clearly demonstrates the enhanced interfacial interaction between rGO nanofillers and PI matrix. The high mechanical property of the APTMS-rGO/PI composites is attributed to the covalent functionalized GO by NH₂ groups and its good dispersion in comparison with GO.     

Tailoring of the interfacial properties of polymeric single fibre-reinforced epoxy composites by non-oxidative plasma treatments

The interfacial properties of epoxy composites reinforced with a single, plasma-treated fibre of either poly(p-phenyleneterephthalamide) (PPTA) or poly(p-phenylenebenzobisoxazole) (PBO) have been investigated with a focus on evaluating the effect of two non-oxidative (He and N₂) microwave plasma treatments on interfacial adhesion properties. Tensile testing of single filaments revealed that their tensile strength does not diminish with the plasma treatments, despite the fact that their surface properties have been both physically and chemically modified. Interfacial characterisation by Raman spectroscopy indicated that the quality of adhesion was substantially enhanced following exposure of the fibres to microwave plasma treatment in either pure helium or pure nitrogen flows for just one minute. Such improvement was higher than that attained when O₂ was used for blowing the plasma, under the same operational conditions. Moreover, no swelling effect was observed by AFM after exposure of the He or N₂ plasma-treated fibres to ambient conditions for as much as 24 h.     

Strain sensing in polymer/carbon nanotube composites by electrical resistance measurement

In this work multiwall carbon nanotubes (MWCNTs) dispersed in a polymer matrix have been used for strain sensing of the resulting nanocomposite under tensile loading. This was achieved by measuring the relative electrical resistance change (ΔR/R₀) in conductive polyvinylidenefluoride (PVDF)/MWCNTs nanocomposites prepared by melt-mixing with varying filler content from 0.5 wt.% to 8 wt.%. Two main parameters were systematically studied. The PVDF/MWCNTs mixing procedure that results in a successful MWCNTs dispersion, and the effect of MWCNTs content on material’s sensing behaviour. The samples were subjected to tensile loading and the longitudinal strain was monitored together with the longitudinal electrical resistance. The results showed that MWCNTs dispersed in insulating PVDF matrix have the potential to be used as a sensitive network to monitor the strain levels in polymer/carbon nanotube nanocomposites as the deformation level of each sample was being reflected by the resistance changes.     

Enhanced thermal resistance of phenolic resin composites at low loading of graphene oxide

By incorporating graphene oxide (GO) into phenolic resin (PR), GO/PR composites were prepared, and the effects of the content and reduction degree of GO on thermal resistance of GO/PR composites were studied. The peak degradation temperature of the PR was increased by about 14 °C with GO which was heat treated. The char yield of GO/PR composite at a GO weight fraction of 0.5% was about 11% greater than that of PR. The interactions such as covalent bonds and π–π stacking between GO and PR were regarded as the main reason for the enhancement. Located at the GO–PR interface, GO effectively anchored and structured PR molecular near the surfaces of GO sheets, and thus facilitated the formation of char. The superiority of GO/PR composites over PR in terms of thermal properties enhancement should also be related to the promoting graphitization by the addition of GO.     

Effects of chitosan as biopolymer coupling agent on the thermal and rheological properties of polyvinyl chloride/wood flour composites

Chitosan (CS) was opted as a novel biopolymer coupling agent for wood flour polyvinyl chloride composites (WF/PVC) to improve interfacial adhesion. This study mainly aimed at investigating the effects after adding CS of different addition amounts and particle sizes on the thermal and rheological properties of WF/PVC composites by the analyses of vicat softening temperature test (VST), differential scanning calorimetry (DSC), thermogravimetry (TGA) and torque rheometry. The results indicated that an optimum addition amount (30 phr) with the particle size (180–220 mesh) could elevate heat resistance capacity, glass transition temperature of composites as well as thermal stability at the early stage of degradation more effectively. In the aspect of rheological characteristics, longer fusion time, lower fusion torque and higher fusion temperature were showed as the CS addition amount increased and the particle size declined. In order to obtain sufficient compaction and ensure proper blending to compounds during extrusion, the higher pressure needed to be supplied when the addition amount of CS exceeded 20 phr.     

Mechanical characteristics and strengthening effectiveness of random-chopped FRP composites containing air voids

In random-chopped fiber-reinforced polymer (FRP) composites used as a retrofit material, a high volume fraction of voids is inevitable due to the manufacturing characteristics. In this paper, the mechanical characteristics and strengthening effectiveness of random-chopped FRP composites containing air porosity are investigated through experiments and numerical analysis. Coupon-shaped specimens with various material compositions were manufactured to examine the uniaxial tensile performance, and the air voids in the composites were measured by a microscope camera. In order to predict the overall performance of the composites, a micromechanical formulation that accounts for porosity was newly developed. The derived model was incorporated into a finite element (FE) code, and the model parameters were estimated by comparing uniaxial tensile test results for various systems of random-chopped FRP composites. In addition, concrete beams strengthened with the composites were produced to evaluate their load-carrying capacity. The FE predictions of the composite structures were then compared with experimental data to verify the predictive capability of the proposed numerical framework.     

Thermal conductivity and dielectric properties of Al/PVDF composites

Polymeric composites with relatively high thermal conductivity, high dielectric permittivity, and a low dissipation factor are obtained in the present study. Three types of core-shell-structured aluminum (Al) particles are incorporated in poly(vinylidene fluoride) (PVDF) by melt-mixing and hot-pressing processes. The morphological, thermal, and dielectric properties of the composites are characterized using thermal analysis, a scanning electron microscope, and a dielectric analyzer. The results indicate that the Al particles decrease the degree of crystallinity of PVDF, and that the particle size and shape of the filler affect the thermal conductivity and dielectric properties of Al/PVDF. No variation in the dissipation factor is observed up to 60 wt.% Al. Thermal conductivity and dielectric permittivity values as high as 1.65 W/m K and 230, respectively, as well as a low dissipation factor of 0.25 at 0.1 Hz, are realized for the composites with 80 wt.% spherical Al.     

An investigation on shape memory behaviours of hydro-epoxy/glass fibre composites

Shape-memory polymers (SMPs) have the capacity to return large strains by external stimuli. Among various SMPs, shape-memory epoxy has received considerable attention because of its superior mechanical and thermal properties as well as excellent shape-memory performance. In this study, short glass fibre-reinforced shape-memory hydro-epoxy composites are developed to improve further the mechanical property of shape-memory epoxy resin. The thermomechanical and shape-memory properties of the developed composite materials are investigated by dynamic mechanical analysis, bend test and shape recovery test. The results indicate that the glass modulus and bend strength of the developed composite materials initially increase and then slightly decrease with increasing short glass fibre content. The glass transition temperature of the developed composite materials does not change with increasing short glass fibre. When the short glass fibre content is less than 4.5 wt.%, full recovery can be observed after only several minutes at different temperatures. The shape-memory property of the composite materials is not affected greatly. However, when the short glass fibre content is more than 4.5 wt.%, the material would be destroyed after deformation.     

The effect of graphene presence in flame retarded epoxy resin matrix on the mechanical and flammability properties of glass fiber-reinforced composites

The effect of adding graphene in epoxy containing either an additive (MP) or reactive-type (DOPO) flame retardant on the thermal, mechanical and flammability properties of glass fiber-reinforced epoxy composites was investigated using thermal analysis; flexural, impact, tensile tests; cone calorimetry and UL-94 techniques. The addition of MP or DOPO to epoxy had a thermal destabilization effect below 400 °C, but led to higher char yield at higher temperatures. The inclusion of 10 wt% flame retardants slightly decreased the mechanical behavior, which was attributed to the poor interfacial interactions in case of MP or the decreased cross-linking density in case of DOPO flame retarded resin. The additional graphene presence increased flexural and impact properties, but slightly decreased tensile performance. Adding graphene further decreased the PHRR, THR and burning rate due to its good barrier effect. The improved fire retardancy was mainly attributed to the reduced release of the combustible gas products.