共查询到20条相似文献,搜索用时 31 毫秒
1.
《Composites Part A》2002,33(2):289-292
The thermal conductivity of polymer composites having a matrix of polystyrene (PS) containing aluminum nitride (AlN) reinforcement has been investigated under a special dispersion state of filler in the composites: aluminum nitride filler particles surrounding polystyrene matrix particles. Data for the thermal conductivity of the composites are discussed as a function of composition parameters (aluminum nitride concentration, polystyrene particle size) and temperature. It is found that the thermal conductivity of composites is higher for a polystyrene particle size of 2 mm than that for a particle size of 0.15 mm. The thermal conductivity of the composite is five times that of pure polystyrene at about 20% volume fraction of AlN for the composite containing 2 mm polystyrene particle size. The relationship between thermal conductivity of composites and AlN filler concentrations has been compared with the predictions of two theoretical models from the literature. 相似文献
2.
This study investigates the thermal conductivity of epoxy composites containing two hybrid fillers which are multi-walled carbon nanotubes (MWCNTs) and aluminum nitride (AlN). To form a covalent bonds between the fillers and the epoxy resin, poly(glycidyl methacrylate) (PGMA) were grafted onto the surface of nano-sized MWCNTs via free radical polymerization and micro-sized AlN was modified by zirconate coupling agent. Results show that functionalized fillers improve thermal conductivity of epoxy composites, due to the good dispersion and interfacial adhesion, which is confirmed by scanning electron microscope. Furthermore, the hybrid fillers provide synergetic effect on heat conductive networks. The thermal conductivity of epoxy composites containing 25 vol.% modified AlN and 1 vol.% functionalized MWCNTs is 1.21 W/mK, comparable to that of epoxy composites containing 50 vol.% untreated AlN (1.25 W/mK), which can reduce the half quantity of AlN filler used. 相似文献
3.
Polyacrylate composites with various fillers such as multi-walled carbon nanotube (CNT), aluminum flake (Al-flake), aluminum powders and Al–CNT were prepared by a ball milling. The thermal decomposition temperature increased by as much as 64 °C for polyacrylate/Al-flake 70 wt% composite compared to polyacrylate. The thermal conductivity of polyacrylate/Al–CNT composites increased from 0.50 to 1.67 W/m K as the Al–CNT content increases from 50 to 80 wt%. The thermal conductivity of the composite sheet increases with the sheet thickness. At the given filler concentration (90 wt%), the composite filled with aluminum powder of 13 μm has a higher thermal conductivity than the one filled 3 μm powder, and the composite filled with mixture of two powders showed a synergistic effect on the thermal conductivity. The morphology indicates that the dispersion of CNT in the polyacrylate/Al-flake + CNT composite is not perfect, and agglomeration of CNTs was observed. 相似文献
4.
Due to the growing needs of thermal management in modern electronics, polyimide-based (PI) composites are increasingly demanded in thermal interface materials (TIMs). Graphene woven fabrics (GWFs) with a mesh structure have been prepared by chemical vapor deposition and used as thermally conductive filler. With the incorporation of 10-layer GWFs laminates (approximate 12 wt%), the in-plane thermal conductivity of GWFs/PI composite films achieves 3.73 W/mK, with a thermal conductivity enhancement of 1418% compared to neat PI. However, the out-of-plane thermal conductivity of the composites is only 0.41 W/mK. The in-plane thermal conductivity exceeds its out-of plane counterpart by over 9 times, indicating a highly anisotropic thermal conduction of GWFs/PI composites. The thermal anisotropy and the enhanced in-plane thermal conductivity can be attributed to the layer-by-layer stacked GWFs network in PI matrix. Thus, the GWFs-reinforced polyimide films are promising for use as an efficient heat spreader for electronic cooling applications. 相似文献
5.
The hybrid filler of hollow glass microspheres (HGM) and nitride particles was filled into low-density polyethylene (LDPE) matrix via powder mixing and then hot pressing technology to obtain the composites with higher thermal conductivity as well as lower dielectric constant (Dk) and loss (Df). The effects of surface modification of nitride particles and HGMs as well as volume ratio between them on the thermal conductivity and dielectric properties at 1 MHz of the composites were first investigated. The results indicate that the surface modification of the filler has a beneficial effect on thermal conductivity and dielectric properties of the composites due to the good interfacial adhesion between the filler and matrix. An optimal volume ratio of nitride particles to HGMs of 1:1 is determined on the basis of overall performance of the composites. The thermal conductivity as well as dielectric properties at 1 MHz and microwave frequency of the composites made from surface-modified fillers with the optimal nitride to HGM volume ratio were investigated as a function of the total volume fraction of hybrid filler. It is found that the thermal conductivity increases with filler volume fraction, and it is mainly related to the type of nitride particle other than HGM. The Dk values at 1 MHz and microwave frequency show an increasing trend with filler volume fraction and depend largely on the types of both nitride particles and HGMs. The Df values at 1 MHz or quality factor (Q × f) at microwave frequency show an increasing or decreasing trend with filler volume fraction and also depend on the types of both nitride particle and HGM. Finally, optimal type of HGM and nitride particles as well as corresponding thermal conductivity and dielectric properties is obtained. SEM observations show that the hybrid filler particles are agglomerated around the LDPE matrix particles, and within the agglomerates the smaller-sized nitride particles in the hybrid filler can easily form thermally conductive networks to make the composites with high thermal conductivity. At the same time, the increase of the value Dk of the composites is restricted due to the presence of HGMs. 相似文献
6.
Rapidly increasing packaging density of electronic devices puts forward higher requirements for thermal conductivity of glass fibers reinforced polymer (GFRP) composites, which are commonly used as substrates in printed circuit board. Interface between fillers and polymer matrix has long been playing an important role in affecting thermal conductivity. In this paper, the effect of interfacial state on the thermal conductivity of functionalized Al2O3 filled GFRP composites was evaluated. The results indicated that amino groups-Al2O3 was demonstrated to be effective filler to fabricate thermally conductive GFPR composite (1.07 W/m K), compared with epoxy group and graphene oxide functionalized Al2O3. It was determined that the strong adhesion at the interface and homogeneous dispersion of filler particles were the key factors. Moreover, the effect of interfacial state on dielectric and thermomechanical properties of GFRP composites was also discussed. This research provides an efficient way to develop high-performance GFRP composites with high thermal conductivity for integrated circuit packaging applications. 相似文献
7.
Aluminum-hydroxide-covered multi-walled carbon nanotubes (A–MWCNT) were fabricated as a thermally conductive material. The thermal conductivity of A–MWCNT was estimated based on Casimir theory. The effective thermal conductivity of A–MWCNT was estimated at about ∼26 W/mK. The thermal conductivity of A–MWCNT/epoxy-terminated polydimethylsiloxane (ETDS) composite was examined as a function of A–MWCNT loading, and the results showed the maximum value at 1.5 wt% of A–MWCNT loading, above which it decreased slightly. The effective medium approximation (EMA) developed by Maxwell–Garnett (M–G) was used to analyze the thermal conducting behavior of the composite. The experimental results showed negative deviation from the expected thermal conductivity, ke, beyond 1.5 wt% of A–MWCNT loading, because the composites containing A–MWCNT were strongly affected by interfacial resistance. The interfacial resistance value calculated from M–G approximation increased when filler loading was higher than 1.5 wt% because of the folded and partially agglomerated A–MWCNT along with insufficient interfacial interactions. 相似文献
8.
We found that the thermal conductivity of polymer composites was synergistically improved by the simultaneous incorporation of graphene nanoplatelet (GNP) and multi-walled carbon nanotube (MWCNT) fillers into the polycarbonate matrix. The bulk thermal conductivity of composites with 20 wt% GNP filler was found to reach a maximum value of 1.13 W/m K and this thermal conductivity was synergistically enhanced to reach a maximum value of 1.39 W/m K as the relative proportion of MWCNT content was increased but the relative proportion of GNP content was decreased. The synergistic effect was theoretically estimated based on a modified micromechanics model where the different shapes of the nanofillers in the composite system could be taken into account. The waviness of the incorporated GNP and MWCNT fillers was found to be one of the most important physical factors determining the thermal conductivity of the composites and must be taken into consideration in theoretical calculations. 相似文献
9.
《材料与设计》2015
Using pressureless infiltration of copper into a bed of coarse (180 μm) diamond particles pre-coated with tungsten, a composite with a thermal conductivity of 720 W/(m K) was prepared. The bending strength and compression strength of the composite were measured as 380 MPa. As measured by sound velocity, the Young's modulus of the composite was 310 GPa. Model calculations of the thermal conductivity, the strength and elastic constants of the copper–diamond composite were carried out, depending on the size and volume fraction of filler particles. The coincidence of the values of bending strength and compressive strength and the relatively high deformation at failure (a few percent) characterize the fabricated diamond–copper composite as ductile. The properties of the composite are compared to the known analogues — metal matrix composites with a high thermal conductivity having a high content of filler particles (~ 60 vol.%). In strength and ductility our composite is superior to diamond–metal composites with a coarse filler; in thermal conductivity it surpasses composites of SiC–Al, W–Cu and WC–Cu, and dispersion-strengthened copper. 相似文献
10.
Cu/diamond composites were fabricated by spark plasma sintering (SPS) after the surface pretreatment of the diamond powders, in which the diamond particles were mixed with copper powder and tungsten powder (carbide forming element W). The effects of the pretreatment temperature and the diamond particle size on the thermal conductivity of diamond/copper composites were investigated. It was found that when 300 μm diamond particles and Cu–5 wt.% W were mixed and preheated at 1313 K, the composites has a relatively higher density and its thermal conductivity approaches 672 W (m K)−1. 相似文献
11.
This paper reports a new approach to enhance the through-thickness thermal conductivity of laminated carbon fabric reinforced composites by using nanoscale and microscale silver particles in combination to create heterogeneously structured continuous through-thickness thermal conducting paths. High conductivity of 6.62 W/(m K) with a 5.1 v% silver volume fraction can be achieved by incorporating these nanoscale and microscale silver particles in EWC-300X/Epon862 composite. Silver flakes were distributed within the inter-tow area, while nanoscale silver particles penetrated into the fiber tows. The combination of different sizes of silver fillers is able to effectively form continuous through-thickness conduction paths penetrating fiber tows and bridging the large inter-tow resin rich areas. Positive hybrid effects to thermal conductivity were found in IM7/EWC300X/sliver particle hybrid composites. In addition, microscale fillers in resin rich areas showed less impact on tensile performance than nanoscale particles applied directly on fiber surface. 相似文献
12.
Polyimide (PI) composites containing one-dimensional SiC nanowires grown on two-dimensional graphene sheets (1D–2D SiCNWs-GSs) hybrid fillers were successfully prepared. The PI/SiCNWs-GSs composites synchronously exhibited high thermal conductivity and retained electrical insulation. Moreover, the heat conducting properties of PI/SiCNWs-GSs films present well reproducibility within the temperature range from 25 to 175 °C. The maximum value of thermal conductivity of PI composite is 0.577 W/mK with 7 wt% fillers loading, increased by 138% in comparison with that of the neat PI. The 1D SiC nanowires grown on the GSs surface prevent the GSs contacting with each other in the PI matrix to retain electrical insulation of PI composites. In addition, the storage modulus and Young’s modulus of PI composites are remarkably improved in comparison with that of the neat PI. 相似文献
13.
Polydimethylsiloxane (PDMS) hybrid composites consisting of exfoliated graphite nanoplatelets (xGnPs) and multiwalled carbon nanotubes functionalized with hydroxyl groups (MWCNTs-OH) were fabricated, and the effects of the xGnP/MWCNT-OH ratio on the thermal, electrical, and mechanical properties of polydimethylsiloxane (PDMS) hybrid composites were investigated. With the total filler content fixed at 4 wt%, a hybrid composite consisting of 75% × GnP/25% MWCNT-OH showed the highest thermal conductivity (0.392 W/m K) and electrical conductivity (1.24 × 10−3 S/m), which significantly exceeded the values shown by either of the respective single filler composites. The increased thermal and electrical conductivity found when both fillers are used in combination is attributed to the synergistic effect between the fillers that forms an interconnected hybrid network. In contrast, the various different combinations of the fillers only showed a modest effect on the mechanical behavior, thermal stability, and thermal expansion of the PDMS composite. 相似文献
14.
Diamond/Al composites were prepared by vacuum hot pressing (VHP) to get high thermal properties. The sintering temperature, pressure and time in the VHP process were optimized. Microstructures, thermal properties, interface reaction product and its effect on the properties of the composites were investigated. The result shows that the sintering temperature and time are key parameters to get high thermal property of the composites. The composites with 20–55 vol% diamond sintered at 650 °C for 90 min under a pressure of 67 MPa exhibit thermal conductivities of 320–567 W/mK, over 90% of the theoretical predictions by the differential effective medium (DEM) scheme. The high thermal conductivity is attributed to the favorable interface conductance, while the formation of aluminum carbide at diamond–Al interface is found to be negative. 相似文献
15.
Multi-walled carbon nanotubes functionalized with amino groups (MWCNT-NH2) were prepared via the chemical modification of the carboxyl groups introduced on the surface of MWCNT. The synthesized materials and untreated micro-aluminum nitride (micro-AlN) particles were embedded in a polymer resin, viz. epoxy-terminated dimethyl siloxane. The thermal diffusivity and conductivity of all of the composites continuously improved with increasing the content of fillers. A thermal conductivity of 3.81 W/mK was achieved at an MWCNT-NH2 loading of 3 wt% and micro-AlN loading of 70 wt% while their flexibility was maintained. This result is due to the high aspect ratio of the MWCNT-NH2 which allows a heat conductive percolation network to be established between the micro-AlN particles. Also, all of the composites fabricated by the optimized process endured about 200,000 bending cycles without rupturing or losing their thermal conductivity. 相似文献
16.
The thermal conductivity of polymer composites containing nanofillers such as GNP (graphene nanoplatelet) and carbon black (CB) was investigated using experimental and theoretical approaches. We developed a fabrication method that allows different shapes and sizes of nanofillers to be highly dispersed in polymer resin. When the bulk and in-plane thermal conductivities of the fabricated composites were measured, they were found to increase rapidly as the GNP filler content increased. The in-plane thermal conductivity of composites with 20 wt.% GNP filler was found to reach a maximum value of 1.98 W/m K. The measured thermal conductivities were compared with the calculated values based on a micromechanics model where the waviness of nanofillers could be taken into account. The waviness of the incorporated GNP filler is an important physical factor that determines the thermal conductivity of composites and must be taken into consideration in theoretical calculations. 相似文献
17.
Chang Heon Kang Kwan Han Yoon Young-Bin Park Dae-Yeol Lee Sung-Sil Jeong 《Composites Part A》2010,41(7):919-926
Polypropylene/aluminum–multi-walled carbon nanotube (PP/Al–CNT) composites were prepared by a twin-screw extruder. The morphology indicates that the CNTs are well embedded or implanted within Al-flakes rather than attached on the surface. During preparation of composites, the CNTs came apart from Al–CNT so that free CNTs as well as Al–CNT were observed in PP/Al–CNT composite. The crystallization temperatures of PP/CNT and PP/Al–CNT composites were increased from 111 °C for PP to 127 °C for the composites. The decomposition temperature increased by 55 °C for PP/CNT composite and 75 °C for PP/Al–CNT composite. The PP/Al–CNT composite showed higher thermal conductivity than PP/CNT and PP/Al-flake composites with increasing filler content. PP/Al–CNT composites showed the viscosity values between PP/CNT and PP/Al-flake composites. PP/Al–CNT composite showed higher tensile modulus and lower tensile strength with increasing filler content compared to PP/CNT and PP/Al-flake composites. 相似文献
18.
Polyhedral oligomeric silsesquioxane grafting thermally conductive silicon carbide particle (POSS-g-SiCp) fillers, are performed to fabricate highly thermally conductive ultra high molecular weight polyethylene (UHMWPE) composites combining with optimal dielectric properties and excellent thermal stabilities, via mechanical ball milling followed by hot-pressing method. The POSS-g-SiCp/UHMWPE composite with 40 wt% POSS-g-SiCp exhibits relative higher thermal conductivity, lower dielectric constant and more excellent thermal stability, the corresponding thermally conductive coefficient of 1.135 W/mK, the dielectric constant of 3.22, and the 5 wt% thermal weight loss temperature of 423 °C, which holds potential for packaging and thermal management in microelectronic devices. Agari’s semi-empirical model fitting reveals POSS-g-SiCp fillers have strong ability to form continuous thermally conductive networks. 相似文献
19.
Wenying Zhou Caifeng Wang Tao Ai Ke Wu Fenjuan Zhao Hongzhi Gu 《Composites Part A》2009,40(6-7):830-836
A novel thermally conductive plastic composite was prepared from a mixture of silicon nitride (Si3N4) filler particles and an ultrahigh molecular weight polyethylene–linear low density polyethylene blend. The effects of Si3N4 particle sizes, concentration, and dispersion on the thermal conductivity and relevant dielectric properties were investigated. With proper fabrication the Si3N4 particles could form a continuously connected dispersion that acted as the dominant thermally conductive pathway through the plastic matrix. By adding 0–20% Si3N4 filler particles, the composite thermal conductivity was increased from 0.2 to ~1.0 W m?1 K?1. Also, the composite thermal conductivity was further enhanced to 1.8 W m?1 K?1 by decreasing the Si3N4 particle sizes from 35, 3 and 0.2 μm, and using coupling agent, for the composites with higher filler content. Alumina short fibers were then added to improve the overall composite toughness and strength. Optimum thermal, dielectric and mechanical properties were obtained for a fiber-reinforced polyethylene composite with 20% total alumina–Si3N4 (0.2 μm size) filler particles. 相似文献
20.
Thermally conducting aluminum nitride polymer-matrix composites 总被引:22,自引:0,他引:22
Thermally conducting, but electrically insulating, polymer-matrix composites that exhibit low values of the dielectric constant and the coefficient of thermal expansion (CTE) are needed for electronic packaging. For developing such composites, this work used aluminum nitride whiskers (and/or particles) and/or silicon carbide whiskers as fillers(s) and polyvinylidene fluoride (PVDF) or epoxy as matrix. The highest thermal conductivity of 11.5 W/(m K) was attained by using PVDF, AlN whiskers and AlN particles (7 μm), such that the total filler volume fraction was 60% and the AlN whisker–particle ratio was 1:25.7. When AlN particles were used as the sole filler, the thermal conductivity was highest for the largest AlN particle size (115 μm), but the porosity increased with increasing AlN particle size. The thermal conductivity of AlN particle epoxy-matrix composite was increased by up to 97% by silane surface treatment of the particles prior to composite fabrication. The increase in thermal conductivity is due to decrease in the filler–matrix thermal contact resistance through the improvement of the interface between matrix and particles. At 60 vol.% silane-treated AlN particles only, the thermal conductivity of epoxy-matrix composite reached 11.0 W/(m K). The dielectric constant was quite high (up to 10 at 2 MHz) for the PVDF composites. The change of the filler from AlN to SiC greatly increased the dielectric constant. Combined use of whiskers and particles in an appropriate ratio gave composites with higher thermal conductivity and low CTE than the use of whiskers alone or particles alone. However, AlN addition caused the tensile strength, modulus and ductility to decrease from the values of the neat polymer, and caused degradation after water immersion. 相似文献