Effect of simulated thermal cycles on the microstructure of the heat-affected zone in HSLA-80 and HSLA-100 steel plates

The influence of weld thermal simulation on the transformation kinetics and heat-affected zone (HAZ) microstructure of two high-strength low-alloy (HSLA) steels, HSLA-80 and HSLA-100, has been investigated. Heat inputs of 10 kJ/cm (fast cooling) and 40 kJ/cm (slow cooling) were used to generate single-pass thermal cycles with peak temperatures in the range of 750 °C to 1400 °C. The prior-austenite grain size is found to grow rapidly beyond 1100 °C in both the steels, primarily with the dissolution of niobium carbonitride (Nb(CN)) precipitates. Dilatation studies on HSLA-80 steel indicate transformation start temperatures (T _s ) of 550 °C to 560 °C while cooling from a peak temperature (T _p ) of 1000 °C. Transmission electron microscopy studies show here the presence of accicular ferrite in the HAZ. The T _s value is lowered to 470 °C and below when cooled from a peak temperature of 1200 °C and beyond, with almost complete transformation to lath martensite. In HSLA-100 steel, the T _s value for accicular ferrite is found to be 470 °C to 490 °C when cooled from a peak temperature of 1000 °C, but is lowered below 450 °C when cooled from 1200 °C and beyond, with correspondingly higher austenite grain sizes. The transformation kinetics appears to be relatively faster in the fine-grained austenite than in the coarse-grained austenite, where the niobium is in complete solid solution. A mixed microstructure consisting of accicular ferrite and lath martensite is observed for practically all HAZ treatments. The coarse-grained HAZ (CGHAZ) of HSLA-80 steel shows a higher volume fraction of lath martensite in the final microstructure and is harder than the CGHAZ of HSLA-100 steel.     

Continuous cooling transformation diagrams applicable to the heat-affected zone of HSLA-80 and HSLA-100 steels

Continuous cooling transformation (CCT) diagrams for HSLA-80 and HSLA-100 steels pertaining to fusion welding with heat inputs of 10 to 40 kJ/cm, and peak temperatures of 1000 °C to 1400 °C have been developed. The corresponding nonlinear cooling profiles and related γ → α phase transformation start and finish temperatures for various peak temperature conditions have been taken into account. The martensite start (M _s ) temperature for each of the grades and ambient temperature microstructures were considered for mapping the CCT diagrams. The austenite condition and cooling rate are found to influence the phase transformation temperatures, transformation kinetics, and morphology of the transformed products. In the fine-grain heat-affected zone (FGHAZ) of HSLA-80 steel, the transformation during cooling begins at temperatures of 550 °C to 560 °C, and in the HSLA-100 steel at 470 °C to 490 °C. In comparison, the transformation temperature is lower by 120 °C and 30 °C in the coarse-grain heat-affected zone (CGHAZ) of HSLA-80 steel and HSLA-100 steel, respectively. At these temperatures, acicular ferrite (AF) and lath martensite (LM) phases are formed. While the FGHAZ contains a greater proportion of acicular ferrite, the CGHAZ has a higher volume fraction of LM. Cooling profiles from the same peak temperature influence the transformation kinetics with slower cooling rates producing a higher volume fraction of acicular ferrite at the expense of LM. The CCT diagrams produced can predict the microstructure of the entire HAZ and have overcome the limitations of the conventional CCT diagrams, primarily with respect to the CGHAZ.     

Effect of microstructure on hydrogen embrittlement of weld-simulated HSLA-80 and HSLA-100 steels

HSLA-80 and HSLA-100 steels have been subjected to weld-simulated grain-coarsened heat-affected zone (GCHAZ) and grain-refined heat-affected zone (GRHAZ) treatments at peak temperatures of 1350 °C and 950 °C, respectively, followed by varying cooling rates to approximate the weld heat inputs of 10 to 50 kJ/cm. Subsequent slow strain rate testing in synthetic seawater has been employed to assess the hydrogen embrittlement (HE) propensity of the materials. It is indicated that in spite of an increase in strength after weld simulation, further ductility deterioration, compared to the base material under similar testing conditions, did not occur in GCHAZ HSLA-100 steel and for low heat input condition of GRHAZ HSLA-80. This has been attributed to their HE resistant microstructures. Predominant acicular ferrite or lath martensite or a combination of both imparts resistance to HE, as observed in the case of grain-coarsened HSLA-100 and for the low heat input grain-refined HSLA-80 steels. The deleterious effect of bainitic-martensitic microstructure has been reflected in the ductility values of grain-coarsened HSLA-80, which is in agreement with the observation of higher susceptibility of the as-received HSLA-100 steel having a similar structure. However, contrary to its beneficial effect in the as-received HSLA-80, an acicular ferrite structure has shown vulnerability toward HE for high heat input grain-refined HSLA-80. This has been attributed to the presence of polygonal ferrite and to the development of an HE susceptible substructure on GRHAZ weld simulation.     

Effect of cooling rate on the as-quenched microstructure and mechanical properties of HSLA-100 steel plates

The effect of cooling rate on the as-quenched microstructure and mechanical properties of a 14-mm-thick HSLA-100 steel using various cooling media such as brine, water, oil, air, and furnace has been studied. While quenching in brine, water, and oil resulted in lath martensite structures, the granular bainite and martensite-austenite (M-A) constituents were found in air- or furnace-cooled specimens. The average lath spacing increased slightly on decreasing the cooling rate (300 nm in brine-quenched specimen to 400 nm in oil-quenched specimen). The precipitates of Cu and Nb(C, N) were observed in all the quenching conditions except in the brine-quenched specimen. The as-quenched strength and toughness of the brine-, water-, and oil-quenched specimens were higher (yield strength: 894 to 997 MPa, ultimate tensile strength: 1119 to 1153 MPa, and Charpy V-notch energies: 65 to 70 J at −85 °C) than those of air- and furnace-cooled specimens (yield strength: 640 to 670 MPa, ultimate tensile strength: 944 to 1001 MPa, and Charpy V-notch energies: 10 to 20 J at −85 °C). For industrial production of HSLA-100 steel plates, oil or water quenching is recommended in lower thickness plates (<25 mm). For production of thicker plates, however, water quenching is more suitable.     

Influence of tempering on the microstructure and mechanical properties of HSLA-100 steel plates

The influence of tempering on the microstructure and mechanical properties of HSLA-100 steel (with C-0.04, Mn-0.87, Cu-1.77, Cr-0.58, Mo-0.57, Ni-3.54, and Nb-.038 pct) has been studied. The plate samples were tempered from 300 °C to 700 °C for 1 hour after austenitizing and water quenching. The transmission electron microscopy (TEM) studies of the as-quenched steel revealed a predominantly lath martensite structure along with fine precipitates of Cu and Nb(C, N). A very small amount of retained austenite could be seen in the lath boundaries in the quenched condition. Profuse precipitation of Cu could be noticed on tempering at 450 °C, which enhanced the strength of the steel significantly (yield strength (YS)—1168 MPa, and ultimate tensile strength (UTS)—1219 MPa), though at the cost of its notch toughness, which dropped to 37 and 14 J at 25 °C and −85 °C, respectively. The precipitates became considerably coarsened and elongated on tempering at 650 °C, resulting in a phenomenal rise in impact toughness (Charpy V-notch (CVN) of 196 and 149 J, respectively, at 25 °C and −85 °C) at the expense of YS and UTS. The best combination of strength and toughness has been obtained on tempering at 600 °C for 1 hour (YS-1015 MPa and UTS-1068 MPa, with 88 J at −85 °C).     

Microstructural changes in HSLA-100 steel thermally cycled to simulate the heat-affected zone during welding

The microstructural changes that occur in a commercial HSLA-100 steel thermally cycled to simulate weld heat affected zone (HAZ) behavior were systematically investigated primarily by transmission electron microscopy (TEM). Eight different weld thermal cycles, with peak temperatures representative of four HAZ regions (the tempered region, the intercritical region, the fine-grained austenitized region, and the coarse-grained austenitized region) and cooling rates characteristic of high heat input (cooling rate (CR) = 5 °C/s) and low heat input (CR = 60 °C/s) welding were simulated in a heating/quenching dilatometer. The as-received base plate consisted of heavily tempered lath martensite, acicular ferrite, and retained austenite matrix phases with precipitates of copper, niobiumcarbonitride, and cementite. The microstructural changes in both the matrix and precipitate phases due to thermal cycling were examined by TEM and correlated with the results of (1) conventional optical microscopy, (2) prior austenite grain size measurements, (3) microhardness testing, and (4) dilatometric analysis. Many of the thermal cycles resulted in dramatic changes in both the microstructures and the properties due to the synergistic interaction between the simulated position in the HAZ and the heat input. Some of these microstructures deviate substantially from those predicted from published continuous cooling transformation (CCT) curves. The final microstructure was predominantly dependent upon peak temperature(i.e., position within the HAZ), although the cooling rate(i.e., heat input) strongly affected the microstructures of the simulated intercritical and finegrained austenitized regions. A. MATUSZESKI, formerly Summer Student, Physical Metallurgy Branch, Naval Research Laboratory.     

Influence of thermomechanical treatments on the microstructure and mechanical properties of HSLA-100 steel plates

The influence of thermomechanical treatment (TMT), i.e., controlled rolling and direct quenching, as a function of rolling temperature and deformation on the microstructure and mechanical properties of HSLA-100 steel have been studied. The optical microstructure of the direct quenched (DQ) and tempered steel rooled at lower temperatures (800 °C and 900 °C) showed elongated and deformed grains, whereas complete equiaxed grains were visible after rolling at 1000 °C. The transmission electron microscope (TEM) microstructure of the 800 °C rooled DQ steel showed shorter, irregular, and closer martensite laths with extremely fine Cu and Nb(C,N) precipitates after tempering at 450 °C. The precipitates coarsened somewhat after tempering at 650 °C; the degree of coarsening was, however, less compared to that of the reheat-quenched (RQ) and tempered steel, indicating that the DQ steel was slightly more resistant to tempering. Similar to the RQ steel, at a 450 °C tempering condition, the DQ steel exhibited peak strength with extremely poor impact toughness. After tempering at 650 °C, the toughness of the DQ steel improved significantly, but at the expense of its strength. In general, the strength of the DQ and tempered steel was good and comparable to that of the RQ and tempered steel, although, its impact toughness was marginally less than the latter. The optimum combination of strength and toughness in the DQ steels was achieved after 900 °C rolling with 50 pct deformation, followed by direct quenching and tempering at 650 °C (yield strength (YS)=903 MPa, ultimate tensile strength (UTS)=928 MPa, and Charpy V-notch (CVN) strength=143 J at −85 °C).     

Failure behavior of heat-affected zones within HSLA-100 and HY-100 steel weldments

The deformation and fracture behavior of simulated heat-affected zones (HAZ) within HSLA-100 and HY-100 steel weldments has been studied as a function of stress state using notched and unnotched axisymmetric tensile specimens. For the case of the HSLA-100 steel, the results for fine-grained, as well as coarse-grain HAZ (CGHAZ) material, show that, despite large differences in the deformation behavior when compared to base plate or weld metal, the failure strains are only weakly dependent on the thermal history or microstructure. Ductile microvoid fracture dominates the failure of the HSLA-100 steel with small losses of ductility occurring in the HAZ conditions only at high stress triaxialities. In contrast, the HY-100 steel is susceptible to a large loss of ductility over all of the stress states when subjected to a severe, single-pass simulation of a CGHAZ. The ductility loss is greatest at the high stress triaxiality ratio in which case failure initiation occurs by a combination of localized cleavage and ductile microvoid fracture.     

二次热循环对管线钢在役焊接粗晶区显微组织的影响

采用焊接热模拟技术、金相分析及透射电镜研究了X70管线钢在役焊接粗晶区及其经受不同峰值温度二次焊接热循环作用后热影响区各区的金相组织和精细结构.结果表明,在役焊接粗晶区的金相组织主要是板条束贝氏体和粒状贝氏体,经历不同峰值温度的二次热循环后,组织类型没有发生变化,但各种组织的形态、大小、数量以及原奥氏体晶粒大小有些差异.热影响区各区的主要形貌都是铁素体板条和分布在板条之间或板条基体上的M-A组元.在役焊接粗晶区M-A组元形态以条状为主,经历二次热循环后,再热临界粗晶区的M-A组元有所细化.再热临界粗晶区存在下贝氏体组织,且具有典型的\     

Effect of magnesium addition in low carbon steel part 2: toughness and microstructure of the simulated coarse-grained heat-affected zone

A critical investigation into the role of Mg on the toughness and microstructure of coarse grain heat-affected zone (CGHAZ) in low carbon steel has been investigated. In this research, the specimens (Mg-free and Mg-added) underwent weld thermal cycle with heat input of 54, 80, and 100?kJ?cm^?1 at 1350°C peak temperature using a thermal simulator. The typical inclusions characteristics were characterised by means of scanning electron microscopy and equilibrium calculations. The precipitates were characterised by transmission electron microscopy and energy-dispersive spectroscopy. It is revealed that the occurrence of Mg in steel mostly exists in the form of Mg-Al-O oxide inclusions, but a few in the form of solid solution state and (Nb,Ti)(C,N)+MgO precipitates when the concentration of Mg is 0.0026%. The improvement of CGHAZ toughness is obtained when the heat input is 80 and 100?kJ?cm^?1. The possible reasons about the effects of Mg on the toughness of CGHAZ, including Mg-Al-O inclusions, precipitates, and soluble Mg, are discussed in detail.     

Simulation study on heat-affected zone of high-strain X80 pipeline steel

The microstructure evolution and impact-toughness variation of heat-affected zone(HAZ)in X80 highstrain pipeline steel were investigated via a welding thermal-simulation technique,Charpy impact tests,and scanning electron microscopy observations under different welding heat inputs and peak temperatures.The results indicate that when heat input was between 17 and 25kJ·cm~(-1),the coarse-grained heat-affected zone showed improved impact toughness.When the heat input was increased further,the martensite-austenite(M-A)islands transformed from fine lath into a massive block.Therefore,impact toughness was substantially reduced.When the heat input was 20kJ·cm~(-1) and the peak temperature of the first thermal cycle was between 900 and 1300°C,a higher impact toughness was obtained.When heat input was 20kJ·cm~(-1) and the peak temperature of the first thermal cycle was 1300°C,the impact toughness value at the second peak temperature of 900°C was higher than that at the second peak temperature of 800°C because of grain refining and uniformly dispersed M-A constituents in the matrix of bainite.     

Effect of TiN particles and microstructure on fracture toughness in simulated heat-affected zones of a structural steel

Thermally stable TiN particles can effectively pin austenite grain boundaries in weld heat-affected zones (HAZs), thereby improving toughness, but can also act as cleavage initiators. The HAZs simulated in a GLEEBLE 1500 TCS using two peak temperatures (T _p ) and three cooling times (Δ∼ _8/5) have determined the effects of matrix microstructure and TiN particle distribution on the fracture toughness (crack tip opening displacement (CTOD)) of three steels microalloyed with 0.006, 0.045, and 0.1 wt pct Ti. Coarse TiN (0.5 to 6 μm) particles are identified in steels with the two higher levels of Ti, and fine Ti(C, N) (35 to 500 nm) particles were present in all three steels. Large prior austenite grain size caused by higher T _p decreased fracture toughness considerably in steels containing coarse TiN particles but had little effect in their absence. Fracture toughness was largely independent of matrix microstructure in the presence of coarse particles. Cleavage fracture initiation was observed to occur at coarse TiN particles in the samples with a large prior austenite grain size. Alloy thermodynamics have been used to rationalize the influence of Ti content on TiN formation and its size.     

钛稀土复合处理对C-Mn钢粗晶热影响区组织及韧性的影响

利用Gleeble-1500D热模拟机进行焊接热影响区热循环模拟实验,研究了在焊接热输入为65 kJ·cm^-1时稀土单独处理和钛稀土复合处理对C-Mn钢粗晶热影响区组织及冲击韧性的影响,并利用扫描电镜观察和分析了实验钢中的夹杂物和冲击断口形貌,利用光镜观察了热循环模拟后实验钢中的微观组织.实验结果表明:稀土单独处理和钛稀土复合处理的试样微观组织分别主要是晶界铁素体+块状铁素体+针状铁素体和晶界铁素体+晶内针状铁素体.经稀土单独处理的试样中夹杂物为La₂O₂S+锰铝硅酸盐+MnS复合夹杂;钛稀土复合处理的试样中的夹杂主要是La₂O₂S+TiO_x+锰铝硅酸盐+MnS复合夹杂.钛稀土复合处理钢中的复合夹杂更细小,有利于形成细小的晶内针状铁素体.钛稀土复合处理极大地改善了实验钢的焊接热影响区低温冲击韧性,比稀土单独处理对试样的冲击性能提升效果更好.     

焊接热循环对微钙钢组织性能的影响

研究了焊接热模拟工艺参数(峰值温度Tp、焊后冷却时间t8/5)和真实焊接对微钙钢热影响区显微组织和性能的影响.用Lepera着色腐蚀剂腐蚀粒状贝氏体中的M-A组元,观察和研究了不同t8/5的热模拟条件下粒状贝氏体中M-A组元的形态、数量及分布特征.结果表明:当冷却速度较快时,M-A组元主要以杆状呈方向性分布;当冷却速度降低时,M-A组元逐渐变成颗粒状,并失去方向性;真实焊接试验结果与热模拟试验结果相符.     

Effect of thermal cycles on microstructure of reduced activation steel fabricated using laser melting deposition

Reduced activation steel was successfully fabricated by laser melting deposition employing a Gaussian and a ring-shaped laser.The microstructure evolution of th...     

Mechanisms and modeling of cleavage fracture in simulated heat-affected zone microstructures of a high-strength low alloy steel

The effect of the welding cycle on the fracture toughness properties of high-strength low alloy (HSLA) steels is examined by means of thermal simulation of heat-affected zone (HAZ) microstructures. Tensile tests on notched bars and fracture toughness tests at various temperatures are performed together with fracture surface observations and cross-sectional analyses. The influence of martensite-austenite (M-A) constituents and of “crystallographic” bainite packets on cleavage fracture micromechanisms is, thus, evidenced as a function of temperature. Three weakest-link probabilistic models (the “Master-curve” (MC) approach, the Beremin model, and a “double-barrier” (DB) model) are applied to account for the ductile-to-brittle transition (DBT) fracture toughness curve. Some analogy, but also differences, are found between the MC approach and the Beremin model. The DB model, having nonfitted, physically based scatter parameters, is applied to the martensite-containing HAZ microstructures and gives promising results.     

Mechanisms and modeling of cleavage fracture in simulated heat-affected zone microstructures of a high-strength low alloy steel

The effect of the welding cycle on the fracture toughness properties of high-strength low alloy (HSLA) steels is examined by means of thermal simulation of heat-affected zone (HAZ) microstructures. Tensile tests on notched bars and fracture toughness tests at various temperatures are performed together with fracture surface observations and cross-sectional analyses. The influence of martensite-austenite (M-A) constituents and of “crystallographic” bainite packets on cleavage fracture micromechanisms is, thus, evidenced as a function of temperature. Three weakest-link probabilistic models (the “Master-curve” (MC) approach, the Beremin model, and a “double-barrier” (DB) model) are applied to account for the ductile-to-brittle transition (DBT) fracture toughness curve. Some analogy, but also differences, are found between the MC approach and the Beremin model. The DB model, having nonfitted, physically based scatter parameters, is applied to the martensite-containing HAZ microstructures and gives promising results.     

原位观察TiN粒子对低合金高强度钢模拟焊接热影响区粗晶区晶粒细化作用

采用高温激光共聚焦显微镜原位观察和电子背散射衍射技术研究TiN粒子在低合金高强度钢模拟大线能量焊接热循环过程中晶粒细化效果.研究发现合理的Ti和N含量能形成大量细小弥散分布的纳米级TiN粒子,在焊接热循环过程中有效钉扎热影响区粗晶区奥氏体晶界,抑制晶粒粗化.同时,TiN附着在Al₂O₃表面析出,在冷却过程中有效促进针状铁素体形核,得到有效晶粒尺寸非常细小的由少量针状铁素体和大量贝氏体构成的复合组织.