Effect of carbon nanotubes on the mechanical properties and crystallization behavior of poly(ether ether ketone)

Pristine carbon nanotubes (CNTs) and noncovalently functionalized carbon nanotubes (f-CNTs) were used to prepare poly(ether ether ketone) (PEEK) composites (CNTs/PEEK and f-CNTs/PEEK) via melt blending. Noncovalently functionalized multiwalled nanotubes were synthesized using hydrogen-bonding interactions between sulfonic groups of sulfonated poly(ether ether ketone) (SPEEK) and carboxylic groups of nanotubes treated by acid (CNTs–COOH). The effects of these two kinds of nanotubes on the mechanical properties and crystallization behavior of PEEK were investigated. CNTs improved mechanical properties and promoted the crystallization rate of PEEK as a result of heterogeneous nucleation. Better enhancement of mechanical properties appeared in the f-CNTs/PEEK composites, which is ascribed to the good interaction between f-CNTs and PEEK. However, the strong interaction of f-CNTs and PEEK chains decreased the crystallization rate of PEEK for high content of f-CNTs.     

Pristine and amino functionalized carbon nanotubes reinforced glass fiber epoxy composites

Multi-phase composites have been studied by incorporating carbon nanotubes (CNTs) as a secondary reinforcement in an epoxy matrix which was then reinforced with glass fiber mat. Different types of CNTs e.g. amino functionalized carbon nanotubes (ACNT) and pristine carbon nanotubes (PCNT) were homogeneously dispersed in the epoxy matrix and two-ply laminates were fabricated using vacuum-assisted resin infusion molding technique. The issues related to CNT dispersion and interfacial bonding and its affect on the mechanical properties have been studied. An important finding of this study is that PCNT scores over ACNT in composites prepared under certain conditions. This is a very significant finding since PCNT is available at a much lower cost than ACNT.     

Tuning the mechanical properties of SWNT/nylon 6,10 composites with flexible spacers at the interface

We have prepared nylon 6,10 nanocomposites using functionalized single wall carbon nanotubes and our interfacial in situ polycondensation method. The specific functional groups -(CH2)nCOCl [n = 4 and 9] on the sidewalls of SWNT were designed to covalently link nanotubes to the nylon matrix via alkyl segments. The composites with functionalized SWNT show significant improvements in tensile modulus, strength, and toughness relative to nylon and nylon modified with non-functionalized SWNT. The alkyl linkages at the SWNT/nylon 6,10 interface contribute significantly to improving the toughness of the composites.     

Preparation,characterization and properties of polycaprolactone diol-functionalized multi-walled carbon nanotube/thermoplastic polyurethane composite

Multi-walled carbon nanotubes (MWCNTs) were chemically functionalized to prepare thermoplastic polyurethane (PU) composites with enhanced properties. In order to achieve a high compatibility of functionalized MWCNTs with the PU matrix, polycaprolactone diol (PCL), as one of PU’s monomers, was selectively grafted on the surface of MWCNTs (MWCNT–PCL), while carboxylic acid groups functionalized MWCNTs (MWCNT–COOH) and raw MWCNTs served as control. Both MWCNT–COOH and MWCNT–PCL improved the dispersion of MWCNTs in the PU matrix and interfacial bonding between them at 1 wt% loading fraction. The MWCNT–PCL/PU composite showed the greatest extent of improvement, where the tensile strength and modulus were 51.2% and 33.5% higher than those of pure PU respectively, without sacrificing the elongation at break. The considerable improvement in both mechanical properties and thermal stability of MWCNT–PCL/PU composite should result from the homogeneous dispersion of MWCNT–PCL in the PU matrix and strong interfacial bonding between them.     

Effect of carbon nanotube type and functionalization on the electrical,thermal, mechanical and electromechanical properties of carbon nanotube/styrene–butadiene–styrene composites for large strain sensor applications

Thermoplastic elastomer tri-block copolymer, namely styrene–butadiene–styrene (SBS) composites filled with carbon nanotubes (CNT) are characterized with the main goal of obtaining electro-mechanical composites suitable for large deformation sensor applications. CNT/SBS composites with different filler contents and filler functionalizations are studied by morphological, thermal, mechanical and electrical analyses. It is shown that the different dispersion levels of CNT in the SBS matrix are achieved for pristine or functionalized CNT with strong influence in the electrical properties of the composites. In particular covalently functionalized CNTs show percolation thresholds higher than 8 weight percentage (wt%) whereas pristine CNT show percolation threshold smaller than 1 wt%. On the other hand, CNT functionalization does not alter the conduction mechanism which is related to hopping between the CNT for concentrations higher than the percolation threshold.Pristine single and multiwall CNT within the SBS matrix allow the preparation of composites with electro-mechanical properties appropriate for strain sensors for deformations up to 5% of strain, the gauge factor varying between 2 and 8. Composites close to the percolation threshold show larger values of the gauge factor.     

Influence of different carbon nanotubes on the electrical and mechanical properties of melt mixed poly(ether sulfone)-multi walled carbon nanotube composites

Commercial Udel® poly(ether sulfone) (PSU) was filled with three different commercially available multiwalled carbon nanotubes (MWCNTs) by small scale melt mixing. The MWCNTs were as grown NC 7000 and two of its derivatives prepared by ball milling treatment. One of them was unmodified (NC 3150); the other was amino modified (NC 3152). The main difference beside the reactivity was the reduced aspect ratio of NC 3150 and NC 3152 caused by ball milling process. All PSU/MWCNT composites with similar filler content were prepared under fixed processing conditions and comparative analysis of their electrical and mechanical properties were performed and were correlated with their microstructure, characterized by optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). A non-uniform MWCNT dispersion was observed in all composites. The MWCNTs were present in form of agglomerates in the size of 10–60 μm whereas the deagglomerated part was homogeneously distributed in the PSU matrix. The differences in the agglomeration states correlate with the variations of properties between different PSU/MWCNT composites. The lowest electrical percolation threshold of 0.25–0.5 wt.% was observed for the shortened non-functionalized MWCNT composites and the highest for amine-modified MWCNT composites (ca. 1.5 wt.%). The tensile behavior of the three composites was only slightly altered with CNT loading as compared to the pure PSU. However, the elongation at break showed a reduction with MWCNT loading and the reduction was least for composite with best MWCNT dispersion.     

The dispersion of SWCNTs treated by dispersing agents in glass fiber reinforced polymer composites

It is an obstacle issue for carbon nanotubes (CNTs) particularly for single-wall carbon nanotubes (SWCNTs) with nano-level dispersion in fiber reinforced polymer matrix composites. In this paper, the dispersing agents such as Volan and BYK-9076 were employed to treat SWCNTs to improve their dispersion in the glass fiber/epoxy (GF/EP) composites. The dispersing results of SWCNTs in composites were observed by scanning electron microscopy (SEM). Then the glass transition temperature (T_g) of these kinds of composites with treated and untreated SWCNTs were obtained by dynamic mechanical thermal analysis (DMTA). Moreover, the flexural tests were performed on these composites. Based on the experiment results, the dispersion of SWCNTs was improved and the flexural property of SWCNTs/GF/EP composite was enhanced too.     

A strategy for improving mechanical properties of a fiber reinforced epoxy composite using functionalized carbon nanotubes

Carbon fiber reinforced epoxy composite laminates are studied for improvements in quasi static strength and stiffness and tension-tension fatigue cycling at stress-ratio (R-ratio) = +0.1 through strategically incorporating amine functionalized single wall carbon nanotubes (a-SWCNTs) at the fiber/fabric-matrix interfaces over the laminate cross-section. In a comparison to composite laminate material without carbon nanotube reinforcements there are modest improvements in the mechanical properties of strength and stiffness; but, a potentially significant increase is demonstrated for the long-term fatigue life of these functionalized nanotube reinforced composite materials. These results are compared with previous research on the cyclic life of this carbon fiber epoxy composite laminate system reinforced similarly with side wall fluorine functionalized industrial grade carbon nanotubes. Optical and scanning electron microscopy and Raman spectrometry are used to confirm the effectiveness of this strategy for the improvements in strength, stiffness and fatigue life of composite laminate materials using functionalized carbon nanotubes.     

碳纳米管增强铝基复合材料的界面研究进展

碳纳米管以其稳定的结构、优异的力学性能,成为复合材料的理想增强相。其增强效果受多方面因素影响,界面是决定其增强效果的关键因素之一,也是金属基复合材料的研究重点。简要介绍了碳纳米管增强铝基(CNTs/Al)复合材料的界面结合机制及界面对复合材料性能的影响,评述了热膨胀系数、制备方法、碳纳米管纯度等多种因素对CNTs/Al复合材料界面的影响,并提出了改善界面的方法。     

Structural characterization of a mechanically milled carbon nanotube/aluminum mixture

The structural evolution of carbon nanotubes (CNTs) during mechanical milling was investigated using SEM, TEM, XRD, XPS and Raman spectroscopy. The study showed that milling of the CNTs alone introduces defects but preserves the tubular structure. When milling the CNTs with aluminum (Al) powder in order to produce a composite, Raman spectroscopy has shown that most of the nanotubes are destroyed. During sintering of the CNT/Al milled mixture, the carbon atoms available from the destruction of the nanotubes react with the Al to form aluminum carbide (Al₄C₃). The effect of milling on the Al matrix was also studied.     

Growth of carbon nanotubes on carbon fibre substrates to produce hybrid/phenolic composites with improved mechanical properties

Carbon nanotubes were grown by chemical vapor deposition (CVD) on different carbon fibre substrates namely, unidirectional (UD) carbon fibre tows, bi-directional (2D) carbon fibre cloth and three dimensional (3D) carbon fibre felt. These substrates were used as the reinforcement in phenolic resin matrix to develop hybrid CF–CNT composites. The growth morphology and other characteristics of the as grown tubes were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and thermal gravimetry (TGA) which confirmed a copious growth of multiwalled carbon nanotubes (MWNTs) on these substrates. The mechanical properties of the hybrid composites was found to increase with the increasing amount of deposited carbon nanotubes. The flexural strength (FS) improved by 20% for UD, 75% for 2D and 66% for 3D hybrid composites as compared to that prepared by neat reinforcements (without CNT growth) under identical conditions. Flexural modulus (FM) of these composites also improved by 28%, 54% and 46%, respectively.     

Mechanical properties of carbon nanotube reinforced polymer nanocomposites: A coarse-grained model

In this work, a coarse-grained (CG) model of carbon nanotube (CNT) reinforced polymer matrix composites is developed. A distinguishing feature of the CG model is the ability to capture interactions between polymer chains and nanotubes. The CG potentials for nanotubes and polymer chains are calibrated using the strain energy conservation between CG models and full atomistic systems. The applicability and efficiency of the CG model in predicting the elastic properties of CNT/polymer composites are evaluated through verification processes with molecular simulations. The simulation results reveal that the CG model is able to estimate the mechanical properties of the nanocomposites with high accuracy and low computational cost. The effect of the volume fraction of CNT reinforcements on the Young's modulus of the nanocomposites is investigated. The application of the method in the modeling of large unit cells with randomly distributed CNT reinforcements is examined. The established CG model will enable the simulation of reinforced polymer matrix composites across a wide range of length scales from nano to mesoscale.     

Effect of carbon nanotube (CNT) content on the mechanical properties of CNT-reinforced aluminium composites

The interest in carbon nanotubes (CNTs) as reinforcements for aluminium (Al) has been growing considerably. Efforts have been largely focused on investigating their contribution to the enhancement of the mechanical performance of the composites. The uniform dispersion of CNTs in the Al matrix has been identified as being critical to the pursuit of enhanced properties. Ball milling as a mechanical dispersion technique has proved its potential. In this work, we use ball milling to disperse up to 5 wt.% CNT in an Al matrix. The effect of CNT content on the mechanical properties of the composites was investigated. Cold compaction and hot extrusion were used to consolidate the ball-milled Al–CNT mixtures. Enhancements of up to 50% in tensile strength and 23% in stiffness compared to pure aluminium were observed. Some carbide formation was observed in the composite containing 5 wt.% CNT. In spite of the observed overall reinforcing effect, the large aspect ratio CNTs used in the present study were difficult to disperse at CNT wt.% greater than 2, and thus the expected improvements in mechanical properties with increase in CNT weight content were not fully realized.     

Interfacial analysis between Mg matrix and carbon nanotubes in Mg-6 wt.% Al alloy matrix composites reinforced with carbon nanotubes

Magnesium containing 6 wt.% aluminum alloy composites reinforced with carbon nanotubes were fabricated with powder metallurgy based wet-processing. Yield stress and tensile strength were successfully improved by the addition of carbon nanotubes. Field emission-transmission electron microscopy microstructural analysis clarified that needle-like ternary carbides of Al₂MgC₂ were synthesized at some interfaces between magnesium matrix and carbon nanotubes, and the other interfaces were clean without any other materials or defects. Tensile loading transfer from magnesium matrix to carbon nanotubes was effectively strengthened by both the production of Al₂MgC₂ compounds and the clean interface between magnesium matrix and carbon nanotubes.     

In situ polymerized nanocomposites: Polystyrene/CNT and Poly(methyl methacrylate)/CNT composites

Carbon nanotubes (CNTs) were incorporated into polystyrene (PS) and poly(methyl methacrylate) (PMMA) matrices via in situ emulsion and emulsion/suspension polymerization methods. The polymerizations were carried out using various initiators, surfactants, and carbon nanotubes to determine their influence on polymerization and on the properties of the composites. The loading of CNTs in the composites varied from 0 to 15 wt.%, depending on the CNTs used. Morphology and dispersion of the CNTs were analyzed by transmission and scanning electron microscopy techniques. The dispersion of multi-walled carbon nanotubes (MWCNT) in the composites was excellent, even at high CNT loading. The mechanical properties, and electrical and thermal conductivities, of the composites were also analyzed. Both electrical and thermal conductivities were improved.     

Synthesis of uniformly dispersed carbon nanotube reinforcement in Al powder for preparing reinforced Al composites

In order to obtain homogeneously dispersed carbon nanotube (CNT) reinforcement with well structure in Al powder, a novel and simple approach was developed as a means of overcoming the limits of traditional mixing methods. This process involves the even deposition of Ni catalyst onto the surface of Al powder by impregnation route with a low Ni content (0.5 wt.%) and in situ synthesis of CNTs in Al powder by chemical vapor deposition. The in situ synthesized CNTs with well-crystallized bamboo-like structure in the composite powders can obviate the reaction with Al below 1000 °C. The feasibility of fabricating CNT/Al composites with high mechanical properties using the as-prepared composite powders was proved by our primary test, which indicated that the compressive yield stress and elastic modulus of 1.5 wt.%-CNT/Al composites synthesized by hot extrusion are 2.2 and 3.0 times as large as that of the pure Al matrix.     

Influence of carbon nanotube-polymeric compatibilizer masterbatches on morphological, thermal, mechanical, and tribological properties of polyethylene

Study was made of the effect of multiwall carbon nanotubes (MWCNTs) and polymeric compatibilizer on thermal, mechanical, and tribological properties of high density polyethylene (HDPE). The composites were prepared by melt mixing in two steps. Carbon nanotubes (CNTs) were melt mixed with maleic anhydride grafted polyethylene (PEgMA) as polymeric compatibilizer to produce a PEgMA-CNT masterbatch containing 20 wt% of CNTs. The masterbatch was then added to HDPE to prepare HDPE nanocomposites with CNT content of 2 or 6 wt%. The unmodified and modified (hydroxyl or amine groups) CNTs had similar effects on the properties of HDPE-PEgMA indicating that only non-covalent interactions were achieved between CNTs and matrix. According to SEM studies, single nanotubes and CNT agglomerates (size up to 1 μm) were present in all nanocomposites regardless of content or modification of CNTs. Addition of CNTs to HDPE-PEgMA increased decomposition temperature, but only slight changes were observed in crystallization temperature, crystallinity, melting temperature, and coefficient of linear thermal expansion (CLTE). Young’s modulus and tensile strength of matrix clearly increased, while elongation at break decreased. Measured values of Young’s moduli of HDPE-PEgMA-CNT composites were between the values of Young’s moduli for longitudinal (E₁₁) and transverse (E₂₂) direction predicted by Mori-Tanaka and Halpin-Tsai composite theories. Addition of CNTs to HDPE-PEgMA did not change the tribological properties of the matrix. Because of its higher crystallinity, PEgMA possessed significantly different properties from HDPE matrix: better mechanical properties, lower friction and wear, and lower CLTE in normal direction. Interestingly, the mechanical and tribological properties and CLTEs of HDPE-PEgMA-CNT composites lie between those of PEgMA and HDPE.     

Influence of screw configuration,residence time,and specific mechanical energy in twin-screw extrusion of polycaprolactone/multi-walled carbon nanotube composites

Melt processing of thermoplastic-based nanocomposites is the favoured route to produce electrically conductive or electrostatic dissipative polymer composites containing carbon nanotubes (CNT). As these properties are desired at low filler fractions, a high degree of dispersion is required in order to benefit from the intrinsic CNT properties. This study discusses the influence of screw configuration, rotation speed, and throughput on the residence time and specific mechanical energy (SME) and the resulting macroscopic CNT dispersion in polycaprolactone (PCL) based masterbatches containing 7.5 wt.% multi-walled carbon nanotubes (MWNT) using an intermeshing co-rotating twin-screw extruder Berstorff ZE25.     

Interconnected multi-walled carbon nanotubes reinforced polymer-matrix composites

A modified method for interconnecting multi-walled carbon nanotubes (MWCNTs) was put forward. And interconnected MWCNTs by reaction of acyl chloride and amino groups were obtained. Scanning electron microscopy shows that hetero-junctions of MWCNTs with different morphologies were formed. Then specimens of pristine MWCNTs, chemically functionalized MWCNTs and interconnected MWCNTs reinforced epoxy resin composites were fabricated by cast moulding. Tensile properties and fracture surfaces of the specimens were investigated. The results show that, compared with pristine MWCNTs and chemically functionalized MWCNTs, the chemically interconnected MWCNTs improved the fracture strain and therefore the toughness of the composites significantly.     

Probing deformation of double-walled carbon nanotube (DWNT)/epoxy composites using FTIR and Raman techniques

Two of the limitations of carbon nanotube (CNT) polymer composites have been the low volume fraction of nanotubes and inadequate load transfer from the polymer to the stiff CNT. Here, we have utilized functionalized mats of double-walled nanotubes (DWNT) to obtain 10 wt.% DWNT in an epoxy matrix, with strength approaching those of quasi-isotropic carbon fiber composites. We used the transmission FTIR technique with in situ loaded specimens to monitor spectral shift per unit applied stress for understanding load transfer behavior at the nanotube–epoxy interface. Tests show that in most cases a tensile stress causes negative FTIR peak shift in the neat epoxy, but this behavior is not always observed for the epoxy matrix in the composite. The FTIR data can be used successfully to estimate the average matrix stress in the composite and thereby the average stress in the nanotubes. In situ Raman studies using the G′ peak are also conducted to obtain complementary information on average tensile stress in the DWNT in the loading direction. The shift response is found to be ∼37 cm⁻¹/GPa.