多弧离子镀NiCrAlY涂层与搪瓷基复合涂层的抗热震行为对比研究

以K444镍基高温合金为基体,采用多弧离子镀法制备了NiCrAlY涂层、喷涂-烧结法制备了搪瓷基复合涂层,并对比研究了2种涂层的抗热震性能。热震实验高温段温度为900℃。高温段保温1.5h后经水或空气冷却为一个热震循环。结果表明,NiCrAlY涂层的抗热震性能较差。当冷却介质为水时,水淬热震30cyc后,涂层表面氧化膜开裂明显,且有个别裂纹已穿透氧化膜,扩展至涂层内部;而搪瓷基复合涂层的抗热震性能非常优异。热震后,涂层表面及内部均未发现裂纹,涂层和基体界面结合良好。经分析,其优良的抗热震性能源于:(1)搪瓷釉热膨胀系数与高温合金基体匹配度高;(2)纳米Ni和NiCrAlY金属颗粒的加入进一步增大涂层热膨胀系数的同时,还提高了搪瓷的韧塑性。     

四种典型高温防护涂层的抗氧化性能

目的系统地评价典型高温防护涂层的抗高温氧化性能,并分析其失效机制。方法通过对比普通Ni Al涂层、NiCrAlY涂层、Pt改性Ni Al涂层以及Pt+Hf共改性Ni Al涂层等四种典型高温防护涂层在1100℃的恒温氧化行为,从氧化过程中的氧化增重、组织结构演变规律等角度出发,分析了四种涂层在高温氧化过程中的抗氧化性能以及氧化失效规律。结果四种涂层在1100℃恒温氧化过程中的增重均符合抛物线规律。普通Ni Al涂层氧化膜粘附性能较差,氧化膜快速剥落,涂层退化最快。NiCrAlY涂层中Y元素在氧化膜/涂层界面形成"钉扎"作用,显著提高氧化膜的粘附性能,但由于涂层内部Al元素含量降低,涂层1100℃氧化300 h后基本失效。Pt改性Ni Al涂层的氧化膜较为完整,但氧化膜起伏严重。Pt+Hf共改性Ni Al涂层的氧化膜均匀完整且无明显起伏,具有综合最优的抗高温氧化性能。结论四种涂层的抗高温氧化性能排序为:Pt+Hf共改性Ni Al Pt改性NiAl普通Ni AlNiCrAlY。     

MCrAlY涂层的研究进展

随着发动机的服役温度日益升高,工作环境日益恶劣,涡轮叶片极易在高温环境中氧化,大大降低了叶片的使用寿命。如何在低成本下制备保护性能好的高温防护涂层,是当前国内外研究的重点。MCrAlY包覆涂层可分为NiCrAlY涂层、CoCrAlY涂层和NiCoCrAlY涂层,这3类涂层的抗氧化性能和抗腐蚀性能较好,又有很好的塑韧性和抗热疲劳性能,因此可作为涂层或热障涂层的黏结层材料。综述了涂层中主要元素(Al、Cr、Co、Y)、掺杂合金元素(Ta、Re、Si、Pt)、涂层制备工艺和预处理工艺对MCrAlY涂层性能的研究进展。结果表明,可以通过调节MCrAlY涂层的成分来实现涂层性能的调控。向MCrAlY涂层中掺入Si、Ta和Re等活性元素,可显著提高涂层的抗高温氧化性能,以进一步提高发动机的工作效率和满足高温的工作环境需求。总结了采用细化涂层晶粒、掺杂纳米颗粒和制备梯度复合涂层等方法来提高MCrAlY涂层的抗氧化性能和抗腐蚀性能的研究现状,对MCrAlY涂层的发展趋势进行了展望。     

共渗制备NiCrAlY涂层及抗高温腐蚀研究

采用热扩散的方法在高温合金K417G基体上制备了NiCrAlY涂层,经测定,涂层以β–NiAl相为主,Cr以固溶态和AlCr(x)相同时存在。1000和1100℃恒温氧化试验表明,NiCrAlY涂层显著提高了合金的抗氧化性,氧化膜致密稳定的Al2O3为主,300h后氧化膜没有明显的剥落。对基体合金和涂层试样进行了900℃,NaCl/Na2SO4(25:75)融盐环境的热腐蚀试验。结果表明,NiCrAlY涂层氧化膜完整,涂层内硫化物含量低,有效提高了抗热腐蚀性能。     

γ-TiAl表面NiCrAlY/Al复合涂层的高温氧化行为

采用磁控溅射和电弧离子镀技术在γ-TiAl合金表面制备NiCrAlY/Al复合涂层,研究了复合涂层对提高γ-TiAl合金抗高温氧化性能的作用机理。经950℃恒温氧化100 h后,涂层表面未发现裂纹和脱落,涂层试样氧化增重值较基体大幅减小。对氧化层进行了SEM、EDS和XRD分析,结果表明无保护涂层的基体γ-TiAl合金表层疏松多孔,无法抵抗高温环境下氧气对基体合金的侵蚀。复合涂层表面的NiCrAlY镀层在氧化过程中形成了Cr2O3,α-Al2O3和β-NiAl相组成的致密防护涂层,阻隔了氧气与基体的接触,中间的Al层为表层持续生成Al2O3提供了Al源。NiCrAlY/Al复合涂层显著提高了基体在950℃下的抗高温氧化性能。     

渗铝改性离子镀NiCrAlY涂层的高温热腐蚀行为

为了进一步改善离子镀NiCrAlY涂层的抗热腐蚀性能,采用粉末包埋法在离子镀NiCrAlY涂层表面上进行渗铝,研究了涂层渗铝前后在850℃含氯硫酸盐膜下的热腐蚀行为.结果表明:在25%NaCl 75%Na2SO4熔盐中850℃热腐蚀40h时,未渗铝的NiCrAlY涂层生成的是外层以Cr2O3为主的氧化膜,渗铝后的NiCrAlY涂层仅生成一层Al2O3膜;未渗铝的NiCrAlY涂层在腐蚀50h后失去保护作用,而渗铝涂层在腐蚀100h后表面仍形成以Al2O3为主的保护膜.因此,渗铝处理可以明显提高原涂层的抗热腐蚀性能.     

两种MCrAlY涂层与DD98M合金的互扩散行为

为研究MCrAlY涂层与DD98M合金的互扩散行为,采用多弧离子镀技术在DD98M合金表面制备了NiCrAlY与NiCoCrAlY涂层,运用XRD、SEM/EDS、EPMA、TEM等方法分别分析了两种MCrAlY涂层对DD98M合金恒温氧化及互扩散行为的影响。结果表明:在1 050℃氧化100 h后,NiCrAlY和NiCoCrAlY涂层表面均形成了一层连续致密的以α-Al2O3为主的保护膜,显著提高了DD98M合金的抗氧化性能。两种MCrAlY涂层与DD98M合金之间形成了因互扩散而导致的互扩散区(IDZ);在NiCoCrAlY涂层试样中还形成了二次反应区(SRZ),但在NiCrAlY涂层试样中却并未发现。NiCoCrAlY涂层试样形成的SRZ中析出了很多针状与颗粒状的μ-TCP相;NiCrAlY涂层试样,合金基体γ/γ′结构中γ′相的体积分数没有明显增加,基体的化学组成与原始成分相比也没有发生明显改变,因此抑制了SRZ的形成。     

铝合金压铸模具钢表面涂层改性研究

采用超音速火焰喷涂复合金属粉末对铝合金压铸模具H13钢进行表面涂层改性,并进行涂层表面性能、模具钢试样的耐磨损性能、抗高温氧化性能和热疲劳性能测试与分析。结果表明,超音速火焰喷涂复合金属粉末表面涂层改性显著改善了模具钢的耐磨损性能、抗高温氧化性能和热疲劳性能。与未进行表面涂层改性相比,表面涂层改性使其20℃、250℃和500℃磨损体积分别减小了85.9%、90.2%和89.6%;500℃高温氧化100 h后的单位面积质量增重减少86.6%;热疲劳裂纹级别从7级变为2级。     

Nb-Hf合金表面Si-Ti-Cr硅化物涂层在恒温氧化和热震中的高温抗氧化性能（英文）

为了提高Nb-Hf合金的高温抗氧化性能,采用浆料烧结和高温渗透制备了Si-Ti-Cr硅化物涂层。分析了Si-Ti-Cr硅化物包覆的Nb-Hf合金样品在恒温氧化和高温热震条件下的抗氧化性能,揭示了Si-Ti-Cr涂层高温恒温氧化和高温热震条件下的失效机理。结果表明,在1800℃恒温氧化5 h条件下,涂层的增重为7 mg/cm²;在1700℃热震循环50周次和恒温氧化5 h条件下,涂层的最大增重为1.8mg/cm²。硅化物涂层在1800℃恒温氧化环境下和1700℃热震/恒温氧化环境下具有优异的抗氧化性能。     

Ti6Al4V钛合金表面Al_2O_3颗粒改性微弧氧化涂层制备及性能（英文）

通过在磷酸盐电解液中加入Al_2O_3陶瓷颗粒,使得在Ti6Al4V钛合金表面的微弧氧化涂层结构和性能得到改性。涂层的结构和性能通过扫描电镜和XRD进行表征和测试,涂层的抗高温氧化性能和热震性能通过高温热循环氧化试验和热震试验进行测试。结果表明,通过在电解液中添加Al_2O_3陶瓷颗粒,涂层由Al_2TiO_5和TiO_2组成,涂层更为致密,表现出更为优异的抗高温氧化和热震性能。电解液中游动的Al_2O_3陶瓷颗粒在微弧氧化过程中被吸入到样品表面并进入涂层,涂层的结构和性能得到改性。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。