Synthesis and thermal expansion of 4J36/ZrW2Os composites

Gas atomized 4336 alloy powder was milled for 72 h then mixed with ZrW2O8 powder and sintered at 600℃ for 4 h under argon atmosphere.4J36/ZrW2O8 composites containing 10 vol.%, 20 vol.%, 30 vol.%, and 40 vol.% ZrW2O8 were fabricated, the relative density of which ranged from 70% to 80%. Thermal expansion coefficients of the composites decreased as the amount of ZrW2O8 increased, in agreement with the rule of the mixture. The coefficient of thermal expansion of the 4J36/40 vol.%ZrW2O8 composite in 25-100℃ is 0.55 ×10-6/℃.     

Recovery of V<Subscript>2</Subscript>O<Subscript>5</Subscript> from Bayer liquor by ion exchange

A new technology was developed to recover V2O5 from Bayer spent liquor by ion exchange.The experimental results show that in the conditions of 105°C and 0.20-0.25 mass ratios between CaO in lime and Al2O3 in spent liquor, the precipitation rate of vanadium in Bayer liquor is more than 85%.The vanadium-bearing precipitation is leached by NaHCO3 solution.The leaching rate of vanadium can reach 85% in the conditions of 95°C, 40 g·L-1 of NaHCO3 concentration, and ventilating of CO2.The 201 × 7 type of resin has...     

Formation of high-density TiN/Ti<Subscript>5</Subscript>Si<Subscript>3</Subscript> ceramic composites using preceramic polymer

The formation, microstructure and properties of high-density TiN/Ti₅Si₃ ceramic composites created by the pyrolysis of preceramic polymer with filler were investigated. Methylpolysiloxane was mixed with TiH₂ as filler and ceramic composites prepared by pyrolysis at 1200°C to 1600°C under N₂, Ar and vacuum were studied. When a specimen with 70 vol.% TiH₂ was pyrolyzed up to 1600°C in a vacuum after a preheat treatment at 850°C in a N₂ atmosphere and subsequently heat-treated at 1600°C for 1 h under Ar at a pressure of 2 MPa, a ceramic composite with full density was obtained. The microstructure of the ceramic composite was composed of TiN and Ti₅Si₃ phases. Under specific pyrolysis conditions, a ceramic composite with a density of 99.2 TD%, a Vickers hardness of 18 GPa, a fracture toughness of 3.5 MPam^1/2, a flexural strength of 270 MPa and a electrical conductivity of 6200 ohm⁻¹·cm⁻¹ was obtained.     

Growth Kinetics and Microstructure Evolution of Intermediate Phases in MoSi<Subscript>2</Subscript>-Si<Subscript>3</Subscript>N<Subscript>4</Subscript>-WSi<Subscript>2</Subscript>/Mo Diffusion Couples

The growth kinetics and silicon diffusion coefficients of intermediate silicide phases in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo diffusion couple prepared by spark plasma sintering were investigated in temperatures ranging from 1200 to 1500 °C. The intermediate silicide phases were characterized by x-ray diffraction. The microstructures and components of the MoSi₂-Si₃N₄-WSi₂/Mo composites were investigated using scanning electron microscope with energy-dispersive spectroscopy. A special microstructure with MoSi₂ core surrounded by a thin layer of (Mo,W)Si₂ ring was found in the MoSi₂-Si₃N₄-WSi₂ composites. The intermediate layers of Mo₅Si₃ and (Mo,W)₅Si₃ in the MoSi₂-Si₃N₄-WSi₂/Mo diffusion couples were formed at different diffusion stages, which grew parabolically. Activation energy of the growth of intermediate layers in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo diffusion couple was calculated to be 316 ± 23 kJ/mol. Besides, the hindering effect of WSi₂ addition on the growth of intermediate layers was illustrated by comparing the silicon diffusion coefficients in MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂/Mo and MoSi₂-3.5 vol.% Si₃N₄/Mo diffusion couples. MoSi₂-3.5 vol.% Si₃N₄-5.0 vol.% WSi₂ coating on Mo substrate exhibited a better high-temperature oxidation resistance in air than that of MoSi₂-3.5 vol.% Si₃N₄ coating.     

Microstructure and Properties of Nanocrystalline Copper Strengthened by a Low Amount of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanoparticles

Dispersion-strengthened Cu-Al₂O₃ materials have been studied over recent years to find an optimum processing route to obtain a high strength, thermal-stable copper alloy designed for modern applications in electrical engineering. The study analyses the influence of 1 vol.% of alumina content on strengthening the copper matrix. Microstructure of the Cu-Al₂O₃ composite was studied by x-ray diffraction as well as scanning and transmission electron microscopy. The composite shows a homogeneous, thermal-stable nanostructure up to 900 °C due to dispersed alumina nanoparticles. The particles effectively strengthen crystallite/grain boundaries in processes of powder consolidation and annealing of the compact. In contrast to monolithic Cu, the Cu-1 vol.% Al₂O₃ exhibits more than double strength and hardness. The nanocrystalline matrix and the low amount of alumina particles result in a yield strength of 288 MPa and a ductility of 15% which is a good combination for practical utilization of the material.     

Microstructure and Thermomechanical Properties of Atmospheric Plasma-Sprayed Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating

In this study, a Yb₂O₃ coating was fabricated by the atmospheric plasma spray technique. The phase composition, microstructure, and thermal stability of the coating were examined. The thermal conductivity and thermal expansion behavior were also investigated. Some of the mechanical properties (elastic modulus, hardness, fracture toughness, and flexural strength) were characterized. The results reveal that the Yb₂O₃ coating is predominantly composed of the cubic Yb₂O₃ phase, and it has a dense lamellar microstructure containing defects. No mass change and exothermic phenomena are observed in the thermogravimetry and differential thermal analysis curves. The high-temperature x-ray diffraction results indicate that no phase transformation occurs from room temperature to 1500 °C, revealing the good phase stability of the Yb₂O₃ coating. The coefficient of thermal expansion of the Yb₂O₃ coating is (7.50-8.67)?×?10^?6 K^?1 in the range of 200-1400 °C. The thermal conductivity is about 1.5 W m^?1 K^?1 at 1200 °C. The Yb₂O₃ coating has excellent mechanical properties and good damage tolerant. The unique combination of these properties implies that the Yb₂O₃ coating might be a promising candidate for T/EBCs applications.     

Synthesis and characterization of Li<Subscript>1.3</Subscript>Al<Subscript>0.3</Subscript>Ti<Subscript>1.7</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by wet chemical route

Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ was prepared by wet chemical route. The phase, surface morphology, and electrochemical properties of the prepared powders were characterized by X-ray diffraction, scanning electron micrograph, and galvanostatic charge-discharge experiments. Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ has similar X-ray diffraction patterns as LiMn₂O₄. The corner and border of Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ particles are not as clear as the uncoated one. The two powders show similar values of lithium-ion diffusion coefficient. When cycled at room temperature and 55°C for 40 times at the charge-discharge rate of 0.2C, Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ shows the capacity retentions of 98.2% and 93.9%, respectively, which are considerably higher than the values of 85.4% and 79.1% for the uncoated one. Both the capacity retention differences between Li_1.3Al_0.3Ti_1.7(PO₄)₃-coated LiMn₂O₄ and LiMn₂O₄ cycling at room temperature and 55°C become larger with the increase of charge-discharge rate. When the charge-discharge rate reaches 2C, the capacity retention of LATP-coated LiMn₂O₄ becomes 8.4% higher than the uncoated LiMn₂O₄ for room temperature cycling, and it becomes 11.1% higher than the latter when cycled at 55°C.     

Effects of cryogenic treatment on the thermal physical properties of Cu<Subscript>76.12</Subscript>Al<Subscript>23.88</Subscript> alloy

The thermal diffusion coefficient,heat capacity,thermal conductivity,and thermal expansion coefficient of Cu76.12Al23.88 alloy before and after cryogenic treatment in the heating temperature range of 25°C to 600°C were measured by thermal constant tester and thermal expansion instrument.The effects of cryogenic treatment on the thermal physical properties of Cu76.12Al23.88 alloy were investigated by comparing the variation of the thermal parameters before and after cryogenic treatment.The results show that the variation trend of the thermal diffusion coefficient,heat capacity,thermal conductivity,and thermal expansion coefficient of Cu76.12Al23.88 alloy after cryogenic treatment was the same as before.The cryogenic treatment can increase the thermal diffusion coefficient,thermal conductivity,and thermal expansion coefficient of Cu76.12Al23.88 alloy and decrease its heat capacity.The maximum difference in the thermal diffusion coefficient between the before and after cryogenic treatment appeared at 400°C.Similarly,thermal conductivity was observed at 200°C.     

Evaluation of in vitro and in vivo tests for surface-modified titanium by H<Subscript>2</Subscript>SO<Subscript>4</Subscript> and H<Subscript>2</Subscript>O<Subscript>2</Subscript> treatment

Titanium is widely used as an implant material for artificial teeth. Furthermore, various studies have examined surface treatment with respect to the formation of a fine passive film on the surface of commercial titanium and its alloys and to improve the bioactivity with bone. However, there is insufficient data about the biocompatibility of implant materials in the body. The purpose of this study was to examine whether surface modification affects the precipitation of apatite on titanium metal. Specimens were chemically washed for 2 min in a 1∶1∶1.5 (vol.%) mixture of 48 %HF, 60%HNO₃ and distilled water. The specimens were then chemically treated with a solution containing 97%H₂SO₄ and 30%H₂O₂ at the ratio of 1∶1 (vol.%) at 40°C for 1h, and subsequently heat-treated at 400°C for 1h. All the specimens were immersed in HBSS with pH 7.4 at 36.5°C for 15d, and the surface was examined with TF-XRD, SEM, EDX and XPS. In addition, specimens of commercial pure Ti, with and without surface treatment, were implanted in the abdominal connective tissue of mice for 28 d. Conventional aluminum and stainless steel 316L were also implanted for comparison. An amorphous titania gel layer was formed on the titanium surface after the titanium specimen was treated with a solution of H₂SO₄ and H₂O₂. The average roughness was 2.175 μm after chemical surface treatment. The amorphous titania was subsequently transformed into anatase by heat treatment at 400°C for 1h. The average thickness of the fibrous capsule surrounding the specimens implanted in the connective tissue was 47.1μm in the chemically treated Ti, and 52.2, 168.7 and 101.9μm, respectively, in the untreated commercial pure Ti, aluminum and stainless steel 316L.     

Thermal and structural role of additives in P<Subscript>2</Subscript>O<Subscript>5</Subscript>-ZnO-Sb<Subscript>2</Subscript>O<Subscript>3</Subscript> glass for low expansion sealing materials

A glass based on the P₂O₅-ZnO-Sb₂O₃ ternary system was modified with various additives, such as RO (R=Ca, Ba and Mn), B₂O₃ and V₂O₅, for low temperature and low expansion sealing materials. The glass transition temperature (T_g) and coefficient of thermal expansion (CTE) were monitored and reduced with additive compositions of RO. Additional incorporation of B₂O₃ at the expense of RO also showed a similar result. Significant improvement was observed when the glass was modified with V₂O_5. A glass showing T_g<350 °C along with CTE<65×10⁻⁷/°C was found, suggesting a high potential for low temperature sealing materials especially for display applications. The role of the quaternary element within the glass is discussed, along with the structural effect using Raman spectroscopy.     

Oxidation resistant Mo-Mo<Subscript>2</Subscript>B-silica and Mo-Mo<Subscript>2</Subscript>B-silicate composites for high temperature applications

Development of Mo composites based on the Mo-Si-B system has been demonstrated as a possible new route to achieving a high temperature Mobased material. In this new system, the silicide phases are replaced directly with silica or other silicate materials. These composites avoid the high ductile to brittle transition temperature observed for Mo-Si-B alloys by removing the Si that exists in solid solution in Mo at equilibrium with its silicides. A variety of compositions is tested for room temperature ductility and oxidation resistance. A system based upon Mo, Mo₂B, and SrO·Al₂O₃·(SiO₂)₂ is shown to possess both ductility at 80 vol.% Mo and oxidation resistance at 60 vol.%. These composites can be produced using a powder processing approach and fired to greater than 95% theoretical density with a desirable microstructure of isolated boride and silicate phases within a ductile Mo matrix.     

Influence of Feedstock Powder Modification by Heat Treatments on the Properties of APS-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-40% TiO<Subscript>2</Subscript> Coatings

The formation and decomposition of aluminum titanate (Al₂TiO₅, tialite) in feedstock powders and coatings of the binary Al₂O₃-TiO₂ system are so far poorly understood. A commercial fused and crushed Al₂O₃-40%TiO₂ powder was selected as the feedstock for the experimental series presented in this paper, as the composition is close to that of Al₂TiO₅. Part of that powder was heat-treated in air at 1150 and 1500 °C in order to modify the phase composition, while not influencing the particle size distribution and processability. The powders were analyzed by thermal analysis, XRD and FESEM including EDS of metallographically prepared cross sections. Only a maximum content of about 45 wt.% Al₂TiO₅ was possible to obtain with the heat treatment at 1500 °C due to inhomogeneous distribution of Al and Ti in the original powder. Coatings were prepared by plasma spraying using a TriplexPro-210 (Oerlikon Metco) with Ar-H₂ and Ar-He plasma gas mixtures at plasma power levels of 41 and 48 kW. Coatings were studied by XRD, SEM including EDS linescans of metallographically prepared cross sections, and microhardness HV1. With the exception of the powder heat-treated at 1500 °C an Al₂TiO₅-Ti₃O₅ (tialite–anosovite) solid solution Al_2?xTi_1+xO₅ instead of Al₂TiO₅ existed in the initial powder and the coatings.     

Microstructure and Physical Properties of Tb<Subscript>2</Subscript>TiO<Subscript>5</Subscript> Neutron Absorber Synthesized by Ball Milling and Sintering

Tb₂TiO₅ neutron absorber was synthesized by ball milling and sintering. Microstructure character of ball-milled Tb₄O₇-17.605%TiO₂ (mass fraction, %) powders and sintered bulks was analyzed using XRD, SEM and TEM. The microhardness, coefficient of thermal expansion and thermal conductivity of sintered bulks were measured. The experiment results showed that the nanocrystalline solid solution was obtained during ball milling. After 96 h of ball milling, TiO₂ was completely solved in Tb₄O₇ and the crystal size of Tb₄O₇ was up to 37 nm. The bulk materials prepared by cold isostatic pressing were sintered at 1300 °C. Tb₂TiO₅ bulks with an orthorhombic structure were obtained. The microhardness of sintered bulks, as well as the thermal conductivity, increased firstly with increasing ball milling time and then decreased. The coefficient of thermal expansion decreased initially and then increased with increasing ball milling time. For the sintered bulk with powder milled for 48 h, the highest values of both microhardness and thermal conductivity were observed, whereas the lowest coefficient of thermal expansion was exhibited. In addition, with increasing testing temperature, the thermal conductivity of sintered bulks initially fell and then rebounded while an opposite trend was found in the coefficient of thermal expansion.     

Phase Relations in the Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-MoO<Subscript>3</Subscript> System in the Solid State. The Crystal Structure of AlVO<Subscript>4</Subscript>

Phase relations in the ternary oxide system Al₂O₃-V₂O₅-MoO₃ in the solid state in air have been investigated by using the x-ray diffraction (XRD) and differential thermal analysis/thermogravimetric (DTA/TG) methods. It was confirmed that in the subsolidus area of the Al₂O₃-V₂O₅-MoO₃ system, there exist seven phases, that is Al₂O₃, V₂O_5(s.s.), MoO₃, AlVO₄, Al₂(MoO₄)₃, AlVMoO₇, and V₉Mo₆O₄₀. Seven fields, in which particular phases coexist at equilibrium, were isolated. The crystal structure of AlVO₄ has been refined from x-ray powder diffraction data. Its space group is triclinic, , Z = 6, with a = 0.65323(1) nm, b = 0.77498(2) nm, c = 0.91233(3) nm, α = 96.175(2)°, β = 107.234(3)°, γ = 101.404(3)°, V = 0.42555 nm³. The crystal structure of the compound is isotypic with FeVO₄. Infrared (IR) spectra of AlVO₄ and FeVO₄ are compared.     

Phase Stability of Ce-Modified La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> Coatings and Chemical Compatibility with YSZ

Ce-modified La₂Zr₂O₇ powders, i.e., La₂Zr₂O₇ (LZ), La₂(Zr_0.7Ce_0.3)₂O₇ (LZ7C3), and La₂(Zr_0.3Ce_0.7)₂O₇ (LZ3C7), were used to produce thermal barrier coatings by atmospheric plasma spray process. The chemical compatibility of the CeO₂-doped La₂Zr₂O₇ with the traditional YSZ was investigated in LZ-YSZ powder mixtures and LZ-YSZ bilayer coatings by x-ray diffraction and scanning electron microscope. The powder mixtures and coatings were aged at 1200 and 1300 °C for 100 h. The results showed that LZ and LZ7C3 presented single pyrochlore structure after the heat treatments at both 1200 and 1300 °C. For LZ3C7, however, fluorite structure was observed at 1300 °C, indicating a poor phase stability of LZ3C7 at the elevated temperature. The results further showed that La₂(Zr_0.3Ce_0.7)₂O₇ reacted with YSZ in the bilayer ceramic coatings due to the diffusion of cerium, zirconium, and yttrium. While for La₂Zr₂O₇(LZ) and La₂(Zr_0.7Ce_0.3)₂O₇, a better chemical compatibility with YSZ was shown.     

Co-reinforcing Al/SiC composites with MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> formed in situ during the processing by non-assisted infiltration

In this work, SiC_P and SiC_P/SiO₂ porous preforms were infiltrated without assistance in Ar→N₂ atmosphere with the alloy Al-10.3 Mg-12.04 Si (wt.%) at 1050 and 1100 °C, for 20, 40 and 60 min. It was found that a decrease in residual porosity and an increase in elastic modulus by about 22 % with respect to composites produced without SiO₂ additions to the preforms are associated with the formation of magnesium aluminate spinel (MgAl₂O₄). A concurrent increase of the matrix hardness is ascribed to a strengthening mechanism by MgAl₂O₄ formation, similar to the strengthening observed with Mg₂Si in aluminum alloys. Therefore, the spinel can be considered as a co-reinforcement of SiC_p in the aluminum matrix composites. Reactions for spinel formation and possible mechanisms for hardness enhancement are outlined.     

Synthesis,Structural, and Adsorption Characteristics of γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> Composite

The γ-Fe₂O₃/SiO₂ composite is synthesized by coprecipitation of the magnetic carrier γ-Fe₂O₃ (specific surface area S = 17 m²/g, pore volume V = 0.51 cm³/g) and silicon dioxide from a solution of sodium-liquid glass. The influence of the synthesis conditions (SiO₂ content, temperature, introduction of electrolyte into reaction mixture) on the structural and adsorption characteristics of the resulting composites is studied. Coprecipitation in the presence of electrolyte (5% NaCl) makes it possible to obtain the most highly porous composites. At SiO₂ content from 20 to 50%, S is from 70 to 150 m²/g, V is from 0.74 to 0.89 cm³/g. These composites have a large adsorption capacity for test substances: a main dye, methylene blue, and an enzyme, cytochrome C. The capacity of these composites on dye (15–40 mg/g) is approximately 10–30 times larger that of the initial iron oxide (1.2 mg/g), and on enzyme (130–280 mg/g) 3–6 times greater than the capacity of iron oxide (45 mg/g). Such composites can be used as magnetic sorbents to for purification, concentration or immobilization of water-soluble organic substances and biopolymers.     

Tribological Properties of Ni<Subscript>3</Subscript>Al Matrix Composite Sliding Against Si<Subscript>3</Subscript>N<Subscript>4</Subscript>, SiC and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> at Elevated Temperatures

The Ni₃Al matrix self-lubricating composite was fabricated by powder metallurgy technique. The tribological behavior of the composite sliding against commercial Si₃N₄, SiC and Al₂O₃ ceramic balls was investigated from 20 to 1000 °C. It was found that the composite demonstrated excellent lubricating properties with different friction pairs at a wide temperature range, which can be attributed to the synergetic effect of Ag, fluorides, and molybdates formed by oxidations. The Ni₃Al matrix self-lubricating composite/Si₃N₄ couple possessed the stable friction coefficient and wear rate.     

Phase Formation of the Yttrium Aluminates in the Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiC System

Phase formation sequence of the yttrium aluminates in the Y₂O₃-Al₂O₃-SiC ternary system as temperature increases were investigated via x-ray diffraction (XRD). Results showed that YAM (monoclinic), YAP (perovskite) and YAG (garnet) were the yttrium aluminates presented in the solid-state reacted samples at a fixed Al₂O₃:SiC ratio of 1:1. Formation of the yttrium aluminates depended on the temperature. The YAM, YAP and YAG started to form below 1150 °C, at 1300 °C, and at 1450 °C, respectively. Accordingly, two behavior phase diagrams of the Y₂O₃-Al₂O₃-SiC ternary system were recognized, one is in the temperature range of 1150-1300 °C and the other is in 1300-1450 °C, respectively. Thereafter, the phase equilibrium was reached in the temperature range of 1450-1700 °C. Effects of SiC on the phase formation processes in the ternary system were discussed.     

Fabrication and magnetic properties of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorods

NiFe₂O₄ nanorods have been successfully synthesized via thermal treatment of the rod-like precursor fabricated by Ni-doped α-FeOOH, which was enwrapped by the complex of citric acid and Ni²⁺. The morphology evolution during the calcination of the precursor nanorods was investigated with transmission electron microscopy (TEM), and the phase and the magnetic properties of samples were analyzed through X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The results indicated that the diameter of the NiFe₂O₄ nanorods obtained ranged between 30 and 50 nm, and the length ranged between 2 and 3 μm. As the calcination temperature was up to 600°C, the coercivity, saturation magnetization, and remanent magnetization of the samples were 36.1 kA·m⁻¹, 27.2 A·m²·kg⁻¹, and 5.3 A·m²·kg⁻¹, respectively. The NiFe₂O₄ nanorods prepared have higher shape anisotropy and superior magnetic properties than those with irregular shapes.