LaAlO3/BaTiO3/SrTiO3三色超晶格的RHEED原位监测

采用激光脉冲分子束外延技术，在（100）取向的STO单晶基片上成功外延生长了LaAlO3／BaTiO3／SrTiO3超晶格。在超晶格薄膜生长过程中采用反射高能电子衍射（RHEED）对LaAlO3／BaTiO3／SrTiO3超晶格的生长过程进行了分析。通过对超晶格中各层RHEED图像分析，发现由于各层面内晶格失配的不同，超晶格各层生长特性有所区别。借助原子力显微镜（AFM）对超晶格表面形貌进行了表征，表明制备的超晶格具有原子级平整的表面。     

AlN/Si衬底上ZnO薄膜的择优取向生长

当ZnO薄膜直接沉积在Si衬底上时,由于ZnO与Si的晶格失配度大,不易于获得高质量的ZnO薄膜.因此,选择合适的衬底材料沉积ZnO薄膜,对提高其质量非常重要.本文采用射频磁控溅射法,通过在Si(100)衬底上预沉积AlN作为ZnO薄膜生长的缓冲层,获得了择优取向的ZnO薄膜.我们还讨论了ZnO薄膜在AlN/Si衬底上的取向生长机理.     

BaTiO3/Si界面扩散与控制方法研究

利用激光分子束外延（LMBE）方法在Si（100）基片上直接生长BaTiO3（BTO）铁电薄膜。通过俄歇电子能谱（AES），X光电子能谱（XPS）等分析手段系统研究了在Si基片上直接生长BTO铁电薄膜过程中的界面扩散现象。根据研究得到的BTO／Si界面扩散规律，采用一种新型的“温度梯度调制生长方法”减小、抑制BTO／Si界面互扩散行为，实现了BTO铁电薄膜在Si基片上的选择性择优定向生长，为在Si基片上制备具有原子级平整度的择优单一取向的BTO铁电薄膜奠定了基础。     

新型硅基双异质外延SOI材料Si/γ-Al2O3/Si制备

异质外延法是目前制备新型SOI材料的技术途径之一。采用低压化学气相沉积技术(LPCVD)在硅衬底上先外延γ-Al2O3绝缘单晶薄膜，制备出硅衬底上外延氧化物外延结构γ-Al2O3/Si(EOS)，然后采用类似SOS薄膜生长的常压CVD(APCVD)方法在EOS上外延硅单晶薄膜，形成新型硅基双异质SOI材料Si／γ-Al2O3／Si。利用反射高能电子衍射(RHEED)、X射线衍射(XRD)、俄歇电子能谱(AES)及MOS电学测量等技术表征分析了Si(100)／γ-Al2O3(100)／Si(100)SOI异质结构的晶体结构、组分和电学性能。测试结果表明，已成功实现了高质量的新型双异质外延SOI结构材料Si(100)／γ-Al2O3(100)／Si(100)，γ-Al2O3与Si外延薄膜均为单晶，γ-Al2O3薄膜具有良好绝缘性能，SOI结构界面清晰陡峭，该SOI材料可应用于CMOS电路的研制。     

硅衬底碳化对异质外延SiC薄膜结构的影响

用LPMOCVD方法在P—Si（111）衬底上异质外延生长SiC,用碳化方法生长出具有单晶结构的3C—SiC薄膜,研究了开始碳化温度、丙烷流量和碳化时间对结晶质量的影响．结果表明,在较低的温度开始碳化不利于丙烷的分解,不能形成很好的过渡层;碳化时丙烷流量过大会造成碳污染,碳化时间过长使过渡层的结晶质量降低．最佳的碳化条件为：开始碳化温度1150℃,碳化时间和碳化时丙烷的流量分别为8min和2sccm．     

3C-SiC/Si(111)的掠入射X射线衍射研究

在衬底温度为1000℃条件下, 利用固源分子束外延(SSMBE)技术在Si衬底上生长3C-SiC单晶薄膜. RHEED结果显示在Si(111)上所生长的SiC薄膜为3C-SiC, 并与衬底的取向基本一致. 采用同步辐射掠入射X射线衍射(GID)技术并结合常规X射线衍射(XRD)研究了SiC薄膜内的应变和晶体质量. 常规衍射的联动扫描曲线得到薄膜处于双轴张应变状态. 3C-SiC薄膜和Si衬底的晶格失配和热膨胀系数失配是导致双轴张应变的原因. 根据不同角度的掠入射衍射Phi扫描的摇摆曲线结果, 发现薄膜晶体质量在远离SiC/Si界面区变好. 这是由于SiC薄膜中的缺陷随着远离界面逐渐减少的原因. GID和XRD的摇摆曲线结果表明薄膜中镶嵌块的倾斜大于扭转, 表明SiC薄膜在面内的晶格排列要比垂直方向更加有序.     

MoS2基板上外延生长C60薄膜的分子动力学模拟

外延生长异质薄膜通常要求材料之间晶格匹配 ,然而利用范德瓦尔斯作用外延生长时 ,晶格匹配要求显著降低。实验上已经得出了在MoS2 基板上外延生长C60 薄膜的结果 ,本文用分子动力学计算机模拟方法对MoS2 基板上外延生长C60 薄膜进行了研究 ,证实范德瓦尔斯外延可以克服较大的晶格失配问题。     

MoS2基板上外延生长C60薄膜的分子动力学模拟

外延生长异质薄膜通常要求材料之间晶格匹配，然而利用范德瓦尔斯作用外延生长时，晶格匹配要求显降低实验上已经得出了在MoS2基板上外延生长C60薄膜的结果，本用分子动力学计算机模拟方法对MoS2基板上外延生长C60薄膜进行了研究，证实范德瓦尔斯外延可以克服较大的晶格失配问题。     

Si(111) 衬底上3C-SiC的超低压低温外延生长

研究了发展一种Si衬底上低温外延生长3C－SiC的方法。采用LPCVD生长系统，以SiH4和C2H4为气源，在超低压（30Pa) ,低温（900℃）的条件下，在Si(111衬底上外延生长出高质量的3C－SiC薄膜材料。采用俄歇能谱（AES），X射线衍射（XRD）和原子力显微镜（AFM）等分析手段研究了SiC薄膜的外延层组分，晶体结构及其表面形貌。AES结果表明薄膜中的Si/C的原子比例符合SiC的理想化学计量比，XRD结果显示了3C－SiC外延薄膜的良好晶体结构，AFM揭示了3C－SiC薄膜的良好的表面形貌。     

PZT/ZnO薄膜制备及其结构特性研究

利用固相反应制备的ZnO-Li_(2.2%)陶瓷靶和RF射频磁控溅射技术在Si(100)基片上制备了高度c轴择优取向的ZnO薄膜,XRD和电性能分析表明掺杂Li离子改善了ZnO靶材的结构和性能,同时研究了不同RF溅射温度对ZnO薄膜结构与取向的影响;然后采用sol-gel前驱单体薄膜制备方法,以ZnO为过渡层淀积PZT薄膜,探讨高度c轴(002)择优取向ZnO薄膜对PZT薄膜结构与性能的影响,实验发现在PZT/ZnO异质结构中,致密、均匀和高度c轴择优取向的ZnO可作为晶核,促进PZT钙钛矿结构转化、晶粒(110)择优取向生长,相应降低PZT薄膜的退火温度.     

Structural and optical properties of high quality ZnO thin film on Si with SiC buffer layer

ZnO thin films are grown on Si substrates with SiC buffer layer using ion plasma high frequency magnetron sputtering. These substrates are fabricated using a technique of solid phase epitaxy. With this technique SiC layer of thickness 20-200 nm had been grown on Si substrates consisting pores of sizes 0.5-5 μm at SiC and Si interface. Due to mismatching in lattice constants as well as thermal expansion coefficients, elastic stresses have been developed in ZnO film. Pores at the interface of SiC and Si are acting as the elastic stress reliever of the ZnO films making them strain free epitaxial. ZnO film grown on this especially fabricated Si substrate with SiC buffer layer exhibits excellent crystalline quality as characterized using X-ray diffraction. Surface topography of the film has been characterized using Atomic Force Microscopy as well as Scanning Electron Microscopy. Chemical compositions of the films have been analyzed using Energy Dispersive X-ray Spectroscopy. Optical properties of the films are investigated using Photoluminescence Spectroscopy which also shows good optical quality.     

The structure and photoluminescence properties of ZnO/SiC multilayer film on Si substrate

ZnO/SiC multilayer film has been fabricated on a Si (111) substrate with a silicon carbide (SiC) buffer layer using the RF (radio frequency)-magnetron technique with targets of a ceramic polycrystalline zinc oxide (ZnO) and a composite target of pure C plate with attached Si chips on the surface. The as-deposited films were annealed at a temperature range of 600–1000°C under nitrogen atmosphere. The structure and photoluminescence (PL) properties of the samples were measured using X-ray diffractometry (XRD), Fourier transform infrared (FTIR) spectroscopy and PL spectrophotometry. By increasing the annealing temperature to 800°C, it is found that all the ZnO peaks have the strongest intensities, and the crystallinity of ZnO is more consistent on the SiC buffer layer. Further increase of the annealing temperature allows the ZnO and SiC layers to penetrate one another, which makes the interface between ZnO and SiC layer become more and more complicated, thus reduces the crystallinities of ZnO and SiC. The PL properties of a ZnO/SiC multilayer are investigated in detail. It is discovered that the PL intensities of these bands reach their maximum after being annealed at 800°C. The PL peaks shift with an increase in the annealing temperature, which is due to the ZnO and SiC layers penetrating reciprocally. This makes the interface more impacted and complicated, which induces band structure deformation resulting from lattice deformation.     

Effect of a ZnO buffer layer on the characteristics of MgZnO thin films grown on Si (100) substrates by radio-frequency magnetron sputtering

This is a report on the effect of a ZnO buffer layer on the microstructures and optical properties of MgZnO thin films grown on Si (100) substrates by radio frequency magnetron sputtering. For the sample without the ZnO buffer layer, the microstructural analyses carried out by X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed the formation of Mg₂Si in the interface between the Si substrate and the MgZnO thin film. Mg₂Si induced the random oriented polycrystalline MgZnO thin film. For the sample with the ZnO buffer layer, a few Mg₂Si were observed. An epitaxial relationship between the Si substrate and the MgZnO thin film was formed. In both samples, the photoluminescence (PL) investigation showed a small blue shift of the emission peak, which was owing to the incorporation of Mg atoms in ZnO by co-sputtering the MgO and ZnO targets. In addition, the sample with the ZnO buffer layer showed the enhanced PL intensity, when compared with the sample without the buffer layer.     

The role of the Zn buffer layers in the structural and photoluminescence properties of ZnO films on Zn buffer layers deposited by RF magnetron sputtering

Highly c-axis oriented ZnO thin films were grown on Si (100) substrates with Zn buffer layers. Effects of the Zn buffer layer thickness on the structural and optical qualities of ZnO thin films were investigated for the ZnO films with the buffer layers 90, 110, and 130 nm thick using X-ray diffraction (XRD), photoluminescence (PL) and atomic force microscopy (AFM) analysis techniques. It was confirmed that the quality of a ZnO thin film deposited by RF magnetron sputtering was substantially improved by using a Zn buffer layer. The highest ZnO film quality was obtained with a Zn buffer layer 110 nm thick. The surface roughness of the ZnO thin film increases as the Zn buffer layer thickness increases.     

The growth of GaN films by alternate source gas supply hot-mesh CVD method

Gallium nitride (GaN) films and Aluminium nitride (AlN) layers were deposited on SiC/Si (111) substrates by an alternating source gas supply or an intermittent supply of a source gas such as ammonia (NH₃), trimethylgallium (TMG) or trimethylaluminum (TMA) in a hot-mesh chemical vapor deposition (CVD) apparatus. The AlN layer was deposited as a buffer layer using NH₃ and TMA on a SiC layer grown by carbonization on Si substrates using propane (C₃H₈). GaN films were grown on an AlN layer by a reaction between NH_x radicals generated on a ruthenium (Ru) coated tungsten (W)-mesh and TMG molecules. An alternating source gas supply or an intermittent supply of one of the source gases during the film growth are expected to be effective for the suppression of gas phase reactions and for the enhancement of precursor migration on the substrate surface. By the intermittent supply of alkylmetal gas only during the growth of the AlN layer, the defect generation in the GaN films was reduced. GaN film growth by intermittent supply on an AlN buffer layer, however, did not lead to the improvement of the film quality.     

Enhanced magnetic properties of chemical solution deposited BiFeO3 thin film with ZnO buffer layer

Magnetic properties of BiFeO₃ films deposited on Si substrates with and without ZnO buffer layer have been studied in this work. We adopted the chemical solution deposition method for the deposition of BiFeO₃ as well as ZnO films. The x-ray diffraction measurements on the deposited films confirm the formation of crystalline phase of BiFeO₃ and ZnO films, while our electron microscopy measurements help to understand the morphology of few micrometers thick films. It is found that the deposited ZnO film exhibit a hexagonal particulate surface morphology, whereas BiFeO₃ film fully covers the ZnO surface. Our magnetic measurements reveal that the magnetization of BiFeO₃ has increased by more than ten times in BiFeO₃/ZnO/Si film compared to BiFeO₃/Si film, indicating the major role played by ZnO buffer layer in enhancing the magnetic properties of BiFeO₃, a technologically important multiferroic material.     

Si(111)衬底上多层石墨烯薄膜的外延生长

利用固源分子束外延(SSMBE)技术, 在Si(111)衬底上沉积碳原子外延生长石墨烯薄膜, 通过反射式高能电子衍射(RHEED)、红外吸收谱(FTIR)、拉曼光谱(RAMAN)和X射线吸收精细结构谱(NEXAFS)等手段对不同衬底温度(400、600、700、800℃)生长的薄膜进行结构表征. RAMAN和NEXAFS结果表明: 在800℃下制备的薄膜具有石墨烯的特征, 而 400、600和700℃生长的样品为非晶或多晶碳薄膜. RHEED和FTIR结果表明, 沉积温度在600℃以下时C原子和衬底Si原子没有成键, 而衬底温度提升到700℃以上, 沉积的C原子会先和衬底Si原子反应形成SiC缓冲层, 且在800℃沉积时缓冲层质量较好. 因此在Si衬底上制备石墨烯薄膜需要较高的衬底温度和高质量的SiC缓冲层.     

Combination of surface texturing and nanostructure coating for reduction of light reflection in ZnO/Si heterojunction thin film solar cell

In this study, we report a single heterojunction solar cell based on n-type zinc oxide/p-type silicon. Three different solar cells were fabricated based on ZnO thin film on Si substrate, ZnO nanorods on Si substrate, and ZnO nanorods on micro-pyramidal structure of Si substrate. The comparison between these three kinds of solar cells was studied. Pyramidal structure of silicon was fabricated using chemical etching technique of p-type Si (100). The chemical solution consists of NaOH, isopropyl alcohol and hydrazine hydrate. The results showed that Si micro-pyramids can enhance optical absorption of Si substrates by increasing surface area and entrapping of incident light. For fabrication of uniform ZnO nanorods, a seed layer of ZnO was deposited on Si substrates via radio frequency magnetron sputtering technique. This layer can be used as an active n-type material in heterojunction solar cells as well. ZnO nanostructures can increase light absorption due to their high specific surface area. The combination of ZnO nanorods and Si micro-pyramids can enhance light trapping effect and increase the efficiency of solar cells. The structural and morphology of samples were studied using field-emission scanning electron microscopy, atomic force microscopy and X-ray diffractometry while the optical properties were investigated using photoluminescence and reflectance spectrometry. The efficiency and fill factor of solar cells were obtained from current–voltage characteristics using a solar simulator and a source-meter. The results showed that the efficiency of solar cell based on nanostructures of ZnO/micropyramids of Si is highly increased due to high anti-reflective behavior of this sample.     

Fabrication of vertical ZnO nanowires on silicon (100) with epitaxial ZnO buffer layer

Vertical ZnO nanowires were successfully grown on epitaxial ZnO (002) buffer layer/Si (100) substrate. The nanowire growth process was controlled by surface morphology and orientation of the epitaxial ZnO buffer layer, which was deposited by radio-frequency (rf) sputtering. The copper catalyzed the vapor-liquid-solid growth of ZnO nanowires with diameter of approximately 30 nm and length of approximately 5.0 microm. The perfect wurtzite epitaxial structure (HCP structure) of the ZnO (0002) nanowires synthesized on ZnO (002) buffer layer/Si (100) substrate results in excellent optical characteristics such as strong UV emission at 380 nm with potential use in nano-optical and nano-electronic devices.     

Influences of Ti film thickness on electrochemical properties of Si/Ti/Cu film electrodes

Si and Si/Ti films were fabricated on a Cu current collector (substrate) using the DC sputtering system. The Ti film as a buffer layer was inserted between the Si film and the Cu current collector. Their structural and electrochemical properties were investigated with various Ti film thicknesses of 20-90 nm. The Si and Ti films deposited on a polycrystalline Cu substrate were amorphous. The Si/Ti/Cu film electrode exhibited better electrochemical properties than the Si/Cu electrode in terms of capacity, charge-discharge efficiency, and cycleability. In the Si/Ti/Cu electrode, the film electrode with a 55 nm Ti film thickness showed the best electrochemical properties: 367 microA h/cm2 initial capacity, 91% efficiency, and 50% capacity retention after 100 cycles. These good electrochemical properties are attributed to the enhanced adhesion between the Si and Ti films. Additionally, the modified surface morphology of Si film with a cluster structure could withstand the lateral volume change during the charge-discharge process.