Stable carbon isotope fractionation during aerobic biodegradation of chlorinated ethenes

Stable isotope analysis is recognized as a powerful tool for monitoring, assessing, and validating in-situ bioremediation processes. In this study, kinetic carbon isotope fractionation factors (epsilon) associated with the aerobic biodegradation of vinyl chloride (VC), cis-1,2-dichloroethylene (cDCE), and trichloroethylene (TCE) were examined. Of the three solvents, the largest fractionation effects were observed for biodegradation of VC. Both metabolic and cometabolic VC degradation were studied using Mycobacterium aurum L1 (grown on VC), Methylosinus trichosporium OB3b (grown on methane), Mycobacterium vaccae JOB5 (grown on propane), and two VC enrichment cultures seeded from contaminated soils of Alameda Point and Travis Air Force Base, CA. M. aurum L1 caused the greatest fractionation (epsilon = -5.7) while for the cometabolic cultures, epsilon values ranged from -3.2 to -4.8. VC fractionation patterns for the enrichment cultures were within the range of those observed for the metabolic and cometabolic cultures (epsilon = -4.5 to -5.5). The fractionation for cometabolic degradation of TCE by Me. trichosporium OB3b was low (epsilon = -1.1), while no quantifiable carbon isotopic fractionation was observed during the cometabolic degradation of cDCE. For all three of the tested chlorinated ethenes, isotopic fractionation measured during aerobic degradation was significantly smaller than that reported for anaerobic reductive dechlorination. This study suggests that analysis of compound-specific isotopic fractionation could assist in determining whether aerobic or anaerobic degradation of VC and cDCE predominates in field applications of in-situ bioremediation. In contrast, isotopic fractionation effects associated with metabolic and cometabolic reactions are not sufficiently dissimilar to distinguish these processes in the field.     

Evaluation of isotopic enrichment factors for the biodegradation of chlorinated ethenes using a parameter estimation model: toward an improved quantification of biodegradation

A model was developed to predict the concentrations of chlorinated ethenes and ethene during sequential reductive dechlorination of tetrachloroethene (PCE) from stable carbon isotope values using Rayleigh model principles and specified isotopic enrichment factors for each step of dechlorination. The model was tested using three separate datasets of concentration and isotope values measured during three experiments involving the degradation of PCE to vinyl chloride (VC), trichloroethene (TCE) to ethene, and cis-1,2-dichloroethene (cDCE) to ethene. The model was then coupled to a parameter estimation method to estimate values for the isotopic enrichment factors of TCE, cDCE, and VC when they are intermediates in the dechlorination to ethene. The enrichment factors estimated for TCE and cDCE when they were intermediates in biodegradation experiments were close to or within the published range of enrichment factors determined from experiments where TCE or cDCE were the initial substrates. In contrast, the enrichment factors determined by parameter estimation for experiments in which VC was an intermediate in biodegradation experiments were consistently more negative (by approximately 10 per thousandth) than the most negative published enrichment factor determined from experiments where VC was the initial substrate. This finding suggests that the range of enrichment factors for VC dechlorination may not be as narrow as previously suggested (-21.5 per thousandth to -26.6 per thousandth) and that fractionation during VC dechlorination when VC is an intermediate compound may be significantly larger than when VC is the initial substrate. These findings have important implications both for the current practice of extrapolating laboratory-derived isotopic enrichment factors to quantify biodegradation of chlorinated ethenes in the field and for understanding the details of enzymatic reductive dechlorination.     

Chlorine isotope fractionation during reductive dechlorination of chlorinated ethenes by anaerobic bacteria

Chlorine isotope fractionation during reductive dechlorination of trichloroethene (TCE) and tetrachloroethene (PCE) to cis-1,2-dichloroethene (cDCE) by anaerobic bacteria was investigated. The changes in the 37Cl/35Cl ratio observed during the one-step reaction (TCE to cDCE) can be explained by the regioselective elimination of chlorine accompanied by the Rayleigh fractionation. The fractionation factors (alpha) of the TCE dechlorination by three kinds of anaerobic cultures were approximately 0.994-0.995 at 30 degrees C. The enrichment of 37Cl in the organic chlorine during the two-step reaction (PCE to cDCE) can be explained by the random elimination of one chlorine atom in the PCE molecule followed by the regioselective elimination of one chlorine atom in the TCE molecule. The fractionation factors for the first step of the PCE dechlorination with three kinds of anaerobic cultures were estimated to be 0.987-0.991 at 30 degrees C using a mathematical model. Isotope fractionation during the first step would be the primary factor for the chlorine isotope fractionation during the PCE dechorination to cDCE. The developed models can be utilized to evaluate the fractionation factors of regioselective and multistep reactions.     

Pathway dependent isotopic fractionation during aerobic biodegradation of 1,2-dichloroethane

1,2-Dichloroethane (1,2-OCA) is a widespread groundwater contaminant known to be biodegradable under aerobic conditions via enzymatic oxidation or hydrolytic dehalogenation reactions. Current literature reports that stable carbon isotope fractionation of 1,2-DCA during aerobic biodegradation is large and reproducible (-27 to -33/1000). In this study, a significant variation in the magnitude of stable carbon isotope fractionation during aerobic biodegradation was observed. Biodegradation in experiments involving microcosms, enrichment cultures, and pure microbial cultures produced a consistent bimodal distribution of enrichment factors (epsilon) with one mean epsilon centered on -3.9 +/- 0.6/1000 and the other on -29.2 +/- 1.9/1000. Reevaluation of epsilon in terms of kinetic isotope effects 12k/13k gave values of 12k/13k = 1.01 and 1.06, which are typical of oxidation and hydrolytic dehalogenation (S(N)2) reactions, respectively. The bimodal distribution is therefore consistent with the microbial degradation of 1,2-DCA by two separate enzymatic pathways. This interpretation is further supported in this study by experiments with pure strains of Xanthobacter autotrophicus GJ10, Ancylobacter aquaticus AD20, and Pseudomonas sp. Strain DCA1 for which the enzymatic degradation pathways are well-known. A small fractionation of -3.0/1000 was measured for 1,2-DCA degradation by Pseudomonas sp. Strain DCA1 (monooxygenase enzyme), while degradation by the hydrolytic dehalogenase enzyme by the other two pure strains was characterized by fractionation of -32.3/1000.     

Oxygen and chlorine isotopic fractionation during perchlorate biodegradation: laboratory results and implications for forensics and natural attenuation studies

Perchlorate is a widespread environmental contaminant having both anthropogenic and natural sources. Stable isotope ratios of O and Cl in a given sample of perchlorate may be used to distinguish its source(s). Isotopic ratios may also be useful for identifying the extent of biodegradation of perchlorate, which is critical for assessing natural attenuation of this contaminant in groundwater. For this approach to be useful, however, the kinetic isotopic fractionations of O and Cl during perchlorate biodegradation must first be determined as a function of environmental variables such as temperature and bacterial species. A laboratory study was performed in which the O and Cl isotope ratios of perchlorate were monitored as a function of degradation by two separate bacterial strains (Azospira suillum JPLRND and Dechlorospirillum sp. FBR2) at both 10 degrees C and 22 degrees C with acetate as the electron donor. Perchlorate was completely reduced by both strains within 280 h at 22 degrees C and 615 h at 10 degrees C. Measured values of isotopic fractionation factors were epsilon(18)O = -36.6 to -29.0% per hundred and epsilon(37)Cl = -14.5 to -11.5% per hundred, and these showed no apparent systematic variation with either temperature or bacterial strain. An experiment using (18)O-enriched water (delta(18)O = +198% per hundred) gave results indistinguishable from those observed in the isotopically normal water (delta(18)O = -8.1% per hundred) used in the other experiments, indicating negligible isotope exchange between perchlorate and water during biodegradation. The fractionation factor ratio epsilon(18)O/epsilon(37)Cl was nearly invariant in all experiments at 2.50 +/- 0.04. These data indicate that isotope ratio analysis will be useful for documenting perchlorate biodegradation in soils and groundwater. The establishment of a microbial fractionation factor ratio (epsilon(18)O/ epsilon(37)Cl) also has significant implications for forensic studies.     

Hydrogen and carbon isotope fractionation during anaerobic biodegradation of aromatic hydrocarbons--a field study

The aquifer of a former manufactured gas plant site, highly contaminated by dissolved monocyclic, heterocyclic, and polycyclic aromatic hydrocarbons, was studied to evaluate the applicability of carbon and hydrogen isotope fractionation to prove ongoing biodegradation of these compounds even in complex aquifer settings. The loss of toluene, o-xylene, p,m-xylene, and 2-methylnaphthalene was accompanied by a considerable carbon isotope fractionation. Additionally, a strong 2H enrichment in residual o-xylene was detected. All isotope fractionations observed could be related to established biochemical degradation mechanisms, each involving a C-H bond cleavage in the rate-determining step. In contrast, other compounds such as 1-methylnaphthalene, methylbenzofuran, and acenaphthene exhibited a uniform stable carbon isotope composition. However, a decrease in concentration for these compounds was observed in the flowpath of the aquifer. High threshold concentrations of acenaphthene downgradient indicate that this contaminant is, if at all, only marginally biodegraded. Detailed analyses of xylenes provided support that compound specific isotope analyses and subsequent application of the Rayleigh model may provide a valuable basis to distinguish between different biodegradation mechanisms as well as dissolution processes in heterogeneous aquifers.     

Stable isotope evidence for biodegradation of chlorinated ethenes at a fractured bedrock site

Stable carbon isotope analysis of chlorinated ethenes and ethene was performed at a site contaminated with trichloroethene (TCE), a dense non-aqueous phase liquid (DNAPL). The site is located in fractured bedrock and had variable groundwater hydraulic gradients during the study due to a local excavation project. Previous attempts to biostimulate a pilot treatment area at the site resulted in the production of cis-1,2-dichloroethene (cis-DCE), the first product of reductive dechlorination of TCE. Cis-DCE concentrations accumulated however, and there was no appreciable production of the breakdown products from further reductive dechlorination, vinyl chloride (VC) and ethene (ETH). Consequently, the pilot treatment area was bioaugmented with a culture of KB-1, a natural microbial consortium known to completely reduce TCE to nontoxic ETH. Due to ongoing dissolution of TCE from DNAPL in the fractured bedrock, and to variable hydraulic gradients, concentration profiles of dissolved TCE and its degradation products cis-DCE, VC, and ETH could not convincingly confirm biodegradation of the chlorinated ethenes. Isotopic analysis of cis-DCE and VC, however, demonstrated that biodegradation was occurring in the pilot treatment area. The isotope values of cis-DCE and VC became significantly more enriched in 13C over the last two sampling dates (in one well from -17.6%o to -12.8%o and from -22.5%o to -18.2%o for cis-DCE and VC, respectively). Quantification of the extent of biodegradation in the pilot treatment area using the Rayleigh model indicated that, depending on the well, between 21.3% and 40.7% of the decrease in cis-DCE and between 15.2% and 36.7% of the decrease in VC concentrations can be attributed to the effects of biodegradation during this time period. Within each well, the isotope profile of TCE remained relatively constant due to the continuous input of undegraded TCE due to DNAPL dissolution.     

Carbon and hydrogen isotopic fractionation during biodegradation of methyl tert-butyl ether

Carbon and hydrogen isotopic fractionation during aerobic biodegradation of MTBE by a bacterial pure culture (PM1) and a mixed consortia from Vandenberg Air Force Base (VAFB) were studied in order to assess the relative merits of stable carbon versus hydrogen isotopic analysis as an indicator of biodegradation. Carbon isotopic enrichment in residual MTBE of up to 8.1/1000 was observed at 99.7% biodegradation. Carbon fractionation was reproducible in the PM1 and VAFB experiments, yielding similar enrichment factors (epsilon) of -2.0/1000 +/- 0.1/1000 to -2.4/1000 +/- 0.3/1000 for replicates in the PM1 experiment and -1.5/1000 +/- 0.1/1000 to -1.8/1000 +/- 0.1/1000 for replicates in the VAFB experiment. Hydrogen isotopic fractionation was highly reproducible for the PM1 pure cultures, with epsilon values of -33/1000 +/- 5/1000 to -37/1000 +/- 4/1000 for replicate samples. In the VAFB microcosms, there was considerably more variability in epsilon values, with values of -29/1000 +/- 4/1000 and -66/1000 +/- 3/1000 measured for duplicate sample bottles. Despite this variability, hydrogen isotopic fractionation always resulted in 2H enrichment of the residual MTBE of >80/1000 at 90% biodegradation. The reproducible carbon fractionation suggests that compound-specific carbon isotope analysis may be used to estimate the extent of biodegradation at contaminated sites. Conversely, the large hydrogen isotopic fractionation documented during biodegradation of MTBE suggests that compound-specific hydrogen isotope analysis offers the most conclusive means of identifying in-situ biodegradation at contaminated sites.     

Hydrogen and carbon isotope fractionation during aerobic biodegradation of benzene

The main aim of the study was to evaluate hydrogen and carbon isotope fractionation during biodegradation of benzene as a possible tool to trace the process in contaminated environments. Aerobic biodegradation of benzene by two bacterial isolates, Acinetobacter sp. and Burkholderia sp., was accompanied by significant hydrogen and carbon isotope fractionation with hydrogen isotope enrichment factors of -12.8 +/- 0.7 per thousand and -11.2 +/- 1.8 per thousand, respectively, and average carbon isotope enrichment factors of -1.46 +/- 0.06 per thousand and -3.53 +/- 0.26 per thousand, respectively. Inorganic carbon produced by Acinetobacter sp. was depleted in 13C by 3.6-6.2 per thousand as compared to the initial delta13C of benzene, while the produced biomass was enriched in 13C by 3.8 per thousand. The secondary aim was to determine isotope ratios of benzenes from different manufacturers with regard to the use of isotopes for source differentiation. While two of the four analyzed benzenes had similar delta13C values, each of them had a distinct delta2H-delta13C pair and delta2H values spread over a range of 66.5 per thousand. Thus, combined analyses of hydrogen and carbon isotopes may be a more promising approach to trace sources and/or biodegradation of benzene than measuring carbon isotopes only.     

Monitoring oxidation of chlorinated ethenes by permanganate in groundwater using stable isotopes: laboratory and field studies

Permanganate injection is increasingly applied for in situ destruction of chlorinated ethenes in groundwater. This laboratory and field study demonstrates the roles that carbon isotope analysis can play in the assessment of oxidation of trichloroethene (TCE) by permanganate. In laboratory experiments a strong carbon isotope fractionation was observed during oxidation of TCE with similar isotopic enrichment factors (-25.1 to -26.8 per thousand) for initial KMnO4 concentrations between 67 and 1,250 mg/L. At the field site, a single permanganate injection episode was conducted in a sandy aquifer contaminated with TCE as dense nonaqueous liquid (DNAPL). After injection, enriched delta13C values of up to +204% and elevated Cl- concentrations were observed at distances of up to 4 m from the injection point. Farther away, the Cl- increased without any change in delta13C of TCE suggesting that Cl- was not produced locally but migrated to the sampling point Except for the closest sampling location to the injection point, the delta13C rebounded to the initial 613C again, likely due to dissolution of DNAPL Isotope mass balance calculations made it possible to identify zones where TCE oxidation continued to occur during the rebound phase. The study indicates that delta13C values can be used to assess the dynamics between TCE oxidation and dissolution and to locate zones of oxidation of chlorinated ethenes that cannot be identified from the Cl- distribution alone.     

Potential for identifying abiotic chloroalkane degradation mechanisms using carbon isotopic fractionation

Degradation of 1,1- and 1,2-dichloroethane (1,1-DCA, 1,2-DCA) and carbon tetrachloride (CCl4) on Zn0 was investigated using compound specific isotope analysis (CSIA) to measure isotopic fractionation factors for chloroalkane degradation by hydrogenolysis, by alpha-elimination, and by beta-elimination. Significant differences in enrichment factors (epsilon) and associated apparent kinetic isotope effects (AKIE) were measured for these different reaction pathways, suggesting that carbon isotope fractionation by beta-elimination is substantially larger than fractionation by hydrogenolysis or by alpha-elimination. Specifically, for 1,1-DCA, the isotopic composition of the reductive alpha-elimination product (ethane) and the hydrogenolysis product (chloroethane) were the same, indicating that cleavage of a single C-Cl bond was the rate-limiting step in both cases. In contrast, for 1,2-DCA, epsilon = epsilon(reactive position) = -29.7 +/- 1.5% per hundred, and the calculated AKIE (1.03) indicated that beta-elimination was likely concerted, possibly involving two C-Cl bonds simultaneously. Compared to 1,1-DCA hydrogenolysis, the AKIE of 1.01 for hydrogenolysis of CCl4 was much lower, indicating that, for this highly reactive organohalide, mass transfer to the surface was likely partially rate-limiting. These findings are a first step toward delineating the relative contribution of these competing pathways in other abiotic systems such as the degradation of chlorinated ethenes on zerovalent iron (ZVI), iron sulfide, pyrite, or magnetite, and, potentially, toward distinguishing between degradation of chlorinated ethenes by abiotic versus biotic processes.     

Oxidation of chlorinated ethenes by heat-activated persulfate: kinetics and products

In situ chemical oxidation (ISCO) and in situ thermal remediation (ISTR) are applicable to treatment of groundwater contaminated with chlorinated ethenes. ISCO with persulfate (S2O8(2-)) requires activation, and this can be achieved with the heat from ISTR, so there may be advantages to combining these technologies. To explore this possibility, we determined the kinetics and products of chlorinated ethene oxidation with heat-activated persulfate and compared them to the temperature dependence of other degradation pathways. The kinetics of chlorinated ethene disappearance were pseudo-first-order for 1-2 half-lives, and the resulting rate constants-measured from 30 to 70 degrees C--fit the Arrhenius equation, yielding apparent activation energies of 101 +/- 4 kJ mol(-1) for tetrachloroethene (PCE), 108 +/- 3 kJ mol(-1) for trichloroethene (TCE), 144 +/- 5 kJ mol(-1) for cis-1,2-dichloroethene (cis-DCE), and 141 +/- 2 kJ mol(-1) for trans-1,2-dichloroethene (trans-DCE). Chlorinated byproducts were observed, but most of the parent material was completely dechlorinated. Arrhenius parameters for hydrolysis and oxidation by persulfate or permanganate were used to calculate rates of chlorinated ethene degradation by these processes over the range of temperatures relevant to ISTR and the range of oxidant concentrations and pH relevant to ISCO.     

Combined carbon and hydrogen isotope fractionation investigations for elucidating benzene biodegradation pathways

Recently, combined carbon and hydrogen isotope fractionation investigations have emerged as a powerful tool for the characterization of reaction mechanisms relevant for the removal of organic pollutants. Here, we applied this approach in order to differentiate benzene biodegradation pathways under oxic and anoxic conditions in laboratory experiments. Carbon and hydrogen isotope fractionation of benzene was studied with four different aerobic strains using a monooxygenase or a dioxygenase for the initial benzene attack, a facultative anaerobic chlorate-reducing strain as well as a sulfate-reducing mixed culture. Carbon and hydrogen enrichment factors (epsilon(C), epsilon(H)) varied for the specific pathways and degradation conditions, respectively, so that from the individual enrichment factors only limited information could be obtained for the identification of benzene biodegradation pathways. However, using the slope derived from hydrogen vs carbon isotope discriminations or the ratio of hydrogen to carbon enrichment factors (lambda = deltaH/ deltaC approximately epsilon(H)/epsilon(C)), benzene degradation mechanisms could be distinguished. Although experimentally determined lambda values partially overlapped, ranges could be determined for different benzene biodegradation pathways. Specific lambda values were < 2 for dihydroxylation, between 7 and 9 for monohydroxylation, and > 17 for anaerobic degradation. Moreover, variations in lambda values suggest that more than one reaction mechanism exists for monohydroxylation as well as for anaerobic benzene degradation under nitrate-reducing, sulfate-reducing, or methanogenic conditions. Our results show that the combined carbon and hydrogen isotope fractionation approach has potential to elucidate biodegradation pathways of pollutants in field and laboratory microcosm studies.     

Competition for sorption and degradation of chlorinated ethenes in batch zero-valent iron systems

The sorption and degradation of the chlorinated ethenes tetrachloroethene (PCE, 5 mg L(-1)) and trichloroethene (TCE, 10 mg L(-1)) were investigated in zero-valent iron systems (ZVI, 100 g L(-1)) in the presence of compounds common to contaminated groundwater with varying physicochemical properties. The potential competitors were chlorinated ethenes, monocyclic aromatic hydrocarbons, and humic acids. The effect of a complex matrix was tested with landfill contaminated groundwater. Nonlinear Freundlich isotherms adequately described chloroethene sorption to ZVI. In the presence of the more hydrophobic PCE (5 mg L(-1)), TCE sorption and degradation decreased by 33% and 30%, respectively, while TCE (10 mg L(-1)) decreased PCE degradation by 30%. In the presence of nonreactive hydrophobic hydrocarbons (i.e., benzene, toluene, and m-xylene at 100 mg L(-1)), TCE and PCE sorption decreased by 73% and 55%, respectively. The presence of the hydrocarbons had no effect on TCE degradation and increased PCE reduction rates by 50%, suggesting that the displacement of the chloroethenes from the sorption sites by the aromatic hydrocarbons enhanced the degradation rates. Humic acids did not interfere significantly with chloroethene sorption or with TCE degradation but lowered PCE degradation kinetics by 36% when present at high concentrations (100 mg L(-1)). The landfill groundwater with an organic carbon content of 109 mg L(-1) C had no effect on chloroethene sorption but inhibited TCE and PCE degradation by 60% and 70%, respectively.     

Monitoring biodegradation of ethene and bioremediation of chlorinated ethenes at a contaminated site using compound-specific isotope analysis (CSIA)

Chlorinated ethenes are commonly found in contaminated groundwater. Remediation strategies focus on transformation processes that will ultimately lead to nontoxic products. A major concern with these strategies is the possibility of incomplete dechlorination and accumulation of toxic daughter products (cis-1,2-dichloroethene (cDCE), vinyl chloride (VC)). Ethene mass balance can be used as a direct indicator to assess the effectiveness of dechlorination. However, the microbial processes that affect ethene are not well characterized and poor mass balance may reflect biotransformation of ethene rather than incomplete dechlorination. Microbial degradation of ethene is commonly observed in aerobic systems but fewer cases have been reported in anaerobic systems. Limited information is available on the isotope enrichment factors associated with these processes. Using compound-specific isotope analysis (CSIA) we determined the enrichment factors associated with microbial degradation of ethene in anaerobic microcosms (ε = -6.7‰ ± 0.4‰, and -4.0‰ ± 0.8‰) from cultures collected from the Twin Lakes wetland area at the Savannah River site in Georgia (United States), and in aerobic microcosms (ε = -3.0‰ ± 0.3‰) from Mycobacterium sp. strain JS60. Under anaerobic and aerobic conditions, CSIA can be used to determine whether biotransformation of ethene is occurring in addition to biodegradation of the chlorinated ethenes. Using δ(13)C values determined for ethene and for chlorinated ethenes at a contaminated field site undergoing bioremediation, this study demonstrates how CSIA of ethene can be used to reduce uncertainty and risk at a site by distinguishing between actual mass balance deficits during reductive dechlorination and apparent lack of mass balance that is related to biotransformation of ethene.     

Experimental evidence for a lack of thermodynamic control on hydrogen concentrations during anaerobic degradation of chlorinated ethenes

Hydrogen (H2) concentrations during reductive dechlorination of cis-dichloroethene (cDCE) and vinyl chloride (VC) were investigated with respectto the influence of parameters entering the Gibbs free energy expression of the reactions. A series of laboratory experiments was conducted employing a mixed, Dehalococcoides-containing enrichment culture capable of complete dechlorination of chlorinated ethenes. The objective was to investigate whether a constant energy gain controls H2 levels in dechlorinating systems, thereby evaluating the applicability of the partial equilibrium approach to microbial dechlorination at contaminated sites. Variations in the temperature between 10 and 30 degrees C did not affect the H2 concentration in a fashion that suggested thermodynamic control through a constant energy gain. In another set of experiments, H2 levels at constant ionic strength were independent of the chloride concentration between 10 and 110 mmol chloride per liter. These findings demonstrate that the partial equilibrium approach is not directly applicable to the interpretation of reductive degradation of chlorinated ethenes. We also present recalculated thermodynamic properties of aqueous chlorinated ethene species that allow for calculation of in-situ Gibbs free energy of dechlorination reactions at different temperatures.     

Ion-specific isotopic fractionation of molybdenum during diffusion in aqueous solutions

Experiments modeling diffusion of Mo in aqueous solutions have been performed and, using multicollector ICP-MS, the ratios of the diffusivities of Mo isotopes, D97Mo/ D95Mo, in aqueous solutions have been determined. Diffusion of MoO42- ions in solution was concomitant with Mo isotopic fractionation with D97Md/D95Mo = 0.99988+/-0.00004 (2sigma for n = 3). In contrast, during diffusion of Mo polyanions, such as Mo70246- and Mo8O264-, no measurable isotope fractionation has been found with D97Mo/D95MO = 1.00000 +/- 0.00002 (2sigma for n = 3). These results indicate the need for due consideration to Mo speciation when attempting to interpret the role of diffusive fluxes in the formation of Mo isotopic signatures in nature. They also raise the possibility that the various chemical forms of other transition metals may be characterized by species-specific isotopic fractionation effects during physicochemical reactions.     

The absence and application of stable carbon isotopic fractionation during the reductive dechlorination of polychlorinated biphenyls

A bacterial enrichment culture (specific to doubly flanked chlorine removal) reductively dechlorinated 2,3,4,5-tetrachlorobiphenyl (2,3,4,5-CB) to 2,3,5-trichlorobiphenyl (2,3,5-CB) in aqueous media. Approximately 90% conversion to 2,3,5-CB occurred after 90 days, with no other products formed. The delta13C values of 2,3,4,5-CB and 2,3,5-CB were relatively constant over the course of the reaction, indicating a very small or no isotope effect. In addition, compound-specific delta13C analysis performed for every congener in three different lots of Aroclor 1268 showed an intrinsic isotopic trend of decreasing 13C abundance with increasing chlorine content, similar to observations in other commercial mixtures of polychlorinated biphenyls (PCBs). The results of this laboratory study suggest that microbial reductive dechlorination of PCBs in contaminated sediments will create congeners with more depleted delta13C values than native PCBs of similar chlorination. Such information may provide additional evidence for the occurrence of this process and aid in further understanding the biogeochemistry of these compounds.     

Enrichment of stable carbon and hydrogen isotopes during anaerobic biodegradation of MTBE: microcosm and field evidence

The conventional approach to evaluate biodegradation of organic contaminants in groundwater is to demonstrate an increase in the concentration of transformation products. This approach is problematic for MTBE from gasoline spills because the primary transformation product (TBA) can also be a component of gasoline. Compound-specific stable isotope analysis may provide a useful alternative to conventional practice. Changes in the delta13C and deltaD of MTBE during biodegradation of MTBE in an anaerobic enrichment culture were compared to the delta13C and deltaD of MTBE in groundwater at nine gasoline spill-sites. The stable isotopes of hydrogen and carbon were extensively fractionated during anaerobic biodegradation of MTBE. The stable isotope enrichment factor for carbon (epsilonC) in the enrichment cultures was -13 (-14.1 to -11.9 at 95% confidence level), and the hydrogen enrichment factor (epsilonH) was -16 (-21 to -11 at 95% confidence level). The isotope enrichment factors for carbon and hydrogen during anaerobic biodegradation indicate that the first reaction is enzymatic hydrolysis of the O-Cmethyl bond. The ratio of epsilonH to epsilonC was consistent between the enrichment culture and the field site that provided the inoculum, and with the other eight sites, suggesting a common degradation pathway. Compound-specific isotope evidence is discussed in terms of its utility for monitoring in situ biodegradation, in particular, for measuring how much MTBE was degraded. For the studied field sites, significant biodegradation of the original mass of MTBE is suggested, in some cases exceeding 90%.